Resources

A uniform horizontal beam of length L=2.40 mL = 2.40\text{ m} is pivoted about a frictionless hinge on a vertical wall at its left end. A technician applies a force of magnitude F=45.0 NF = 45.0\text{ N} at the right end of the beam at an angle of θ=35.0∘\theta = 35.0^\circ above the horizontal. Calculate the magnitude of the torque exerted by this force about the pivot at the left end, and state whether this torque tends to cause clockwise or counterclockwise rotation.

Answer and steps

Final answer

τ=61.9 N⋅m\tau = 61.9\text{ N}\cdot\text{m}, counterclockwise

Steps

01

Identify the Formula for Torque

The magnitude of torque τ\tau produced by a force F⃗\vec{F} exerted at a position vector r⃗\vec{r} relative to a pivot is given by:

τ=rFsin⁡θ\tau = r F \sin\theta

where:

  • rr is the distance from the pivot point to the point of application of the force.
  • FF is the magnitude of the applied force.
  • θ\theta is the angle between the position vector r⃗\vec{r} (directed along the beam from the pivot to the right end) and the force vector F⃗\vec{F}.

Alternatively, torque can be viewed as the lever arm times the perpendicular component of the force:

τ=rF⊥=r(Fsin⁡θ)\tau = r F_{\perp} = r (F \sin\theta)


02

Substitute the Given Values

From the problem statement:

  • r=L=2.40 mr = L = 2.40\text{ m}
  • F=45.0 NF = 45.0\text{ N}
  • θ=35.0∘\theta = 35.0^\circ

Compute the magnitude:

τ=(2.40 m)(45.0 N)sin⁡(35.0∘)\tau = (2.40\text{ m})(45.0\text{ N})\sin(35.0^\circ)

τ=(108.0 N⋅m)(0.57358)≈61.946 N⋅m≈61.9 N⋅m\tau = (108.0\text{ N}\cdot\text{m})(0.57358) \approx 61.946\text{ N}\cdot\text{m} \approx 61.9\text{ N}\cdot\text{m}


03

Determine the Direction of Rotation

  • Decompose the force into components:
    • The horizontal component Fx=Fcos⁡(35.0∘)F_x = F \cos(35.0^\circ) acts along the line extending directly through the pivot, producing zero torque because its line of action passes through the rotation axis.
    • The vertical component Fy=Fsin⁡(35.0∘)F_y = F \sin(35.0^\circ) pulls the right end of the beam upward.
  • Because the beam is fixed at the left end, an upward force at the right end causes the beam to rotate upward and to the left around the pivot, which is a counterclockwise direction.

Common Pitfall: Be careful not to use cos⁡θ\cos\theta instead of sin⁡θ\sin\theta. Only the component perpendicular to the beam (Fsin⁡θF\sin\theta) creates torque. The parallel component (Fcos⁡θF\cos\theta) only pulls against the hinge and contributes no rotational tendency.

Typical errors

OverviewACEpath Teacher's Diagnosis

01 The student uses the cosine of the angle instead of the sine, calculating the torque from the parallel component of the force.

Sample Student Work

Reviewed by ACEpath Teacher
Step-by-Step Review
Walk Through It with Your Teacher
Partially correct
  1. Step 1

    τ=r⋅F⋅cos⁡(35.0∘)  ⟹  τ=2.40⋅45.0⋅0.8192  ⟹  τ=88.5 N⋅m\tau = r \cdot F \cdot \cos(35.0^\circ) \implies \tau = 2.40 \cdot 45.0 \cdot 0.8192 \implies \tau = 88.5\text{ N}\cdot\text{m}

    Correct

    τ=rFsin⁡(35.0∘)=(2.40 m)(45.0 N)sin⁡(35.0∘)≈61.9 N⋅m\tau = r F \sin(35.0^\circ) = (2.40\text{ m})(45.0\text{ N})\sin(35.0^\circ) \approx 61.9\text{ N}\cdot\text{m}

    You used cos⁡(35.0∘)\cos(35.0^\circ) to find the torque. The horizontal component Fcos⁡(35.0∘)F\cos(35.0^\circ) acts directly along the beam and passes through the pivot, contributing zero torque. Torque depends only on the perpendicular component of the force, which is Fsin⁡(35.0∘)F\sin(35.0^\circ).

  2. Step 2

    Counterclockwise\text{Counterclockwise}

WHAT YOU DID WELL
Compliments from Your Teacher

You correctly identified the lever arm distance r=2.40 mr = 2.40\text{ m} from the pivot to the point of force application.

You correctly evaluated the rotational direction as counterclockwise.

You carried out your arithmetic accurately based on the formula you wrote.

THE ERROR
Where Your ACEpath Teacher Spotted the Mistake
Trigonometric Component Selection

You accidentally selected the cosine function instead of the sine function when resolving the force vector for torque.

WHY IT HAPPENED
ACEpath Teacher's Diagnosis

You associated the horizontal angle with the standard cosine projection without verifying whether that component is perpendicular or parallel to the lever arm.

REASONING PATH
Your ACEpath teacher’s suggested approach
Identify the perpendicular component
  • Only the component of force perpendicular to the radial position vector r⃗\vec{r} produces torque: τ=rF⊥=rFsin⁡θ\tau = r F_\perp = r F \sin\theta, where θ\theta is the angle between r⃗\vec{r} and F⃗\vec{F}.

  • Draw the force components relative to the beam; eliminate the component pointing along the beam and keep only the perpendicular component.

CORRECTED PATH
ACEpath Teacher's Demonstration
  1. Identify the perpendicular force component: F⊥=Fsin⁡(35.0∘)=45.0 N×sin⁡(35.0∘)≈25.81 NF_\perp = F\sin(35.0^\circ) = 45.0\text{ N} \times \sin(35.0^\circ) \approx 25.81\text{ N}.

  2. Multiply the perpendicular force by the distance to the pivot: τ=rF⊥=(2.40 m)(25.81 N)≈61.9 N⋅m\tau = r F_\perp = (2.40\text{ m})(25.81\text{ N}) \approx 61.9\text{ N}\cdot\text{m}.

Final answer

τ=61.9 N⋅m\tau = 61.9\text{ N}\cdot\text{m}, counterclockwise

NEXT STEPS
Final Takeaways from Your Teacher
  • Sketch the force at the application point and break it into parallel and perpendicular components relative to the beam before writing the torque equation.

  • Check whether the component passes through the pivot axis; any force component whose line of action crosses the pivot produces zero torque.

OverviewACEpath Teacher's Diagnosis

02 The student omits the angular factor entirely, assuming the force acts purely perpendicular to the beam.

Sample Student Work

Reviewed by ACEpath Teacher
Step-by-Step Review
Walk Through It with Your Teacher
Partially correct
  1. Step 1

    τ=r∗F  ⟹  τ=2.40∗45.0\tau = r * F \implies \tau = 2.40 * 45.0

    Correct

    τ=rFsin⁡θ=(2.40 m)(45.0 N)sin⁡(35.0∘)\tau = r F \sin\theta = (2.40\text{ m})(45.0\text{ N})\sin(35.0^\circ)

    You used the simplified formula τ=rF\tau = r F, which assumes the force acts perpendicular to the lever arm. Because the force is applied at an angle of θ=35.0∘\theta = 35.0^\circ above the horizontal beam, you need to include the factor sin⁡θ\sin\theta to find the perpendicular component of the force.

  2. Step 2

    τ=108 N⋅m\tau = 108\text{ N}\cdot\text{m}

    Correct

    τ≈61.9 N⋅m\tau \approx 61.9\text{ N}\cdot\text{m}

    Your arithmetic (2.40)(45.0)=108(2.40)(45.0) = 108 was computed accurately from your previous expression, but the value is incorrect due to the missing sin⁡(35.0∘)\sin(35.0^\circ) factor.

  3. Step 3

    Counterclockwise\text{Counterclockwise}

WHAT YOU DID WELL
Compliments from Your Teacher

You correctly identified the pivot distance r=2.40 mr = 2.40\text{ m} and force magnitude F=45.0 NF = 45.0\text{ N}.

You accurately determined that the upward vertical component creates a counterclockwise torque.

THE ERROR
Where Your ACEpath Teacher Spotted the Mistake
Omitted angular factor in torque calculation

no

WHY IT HAPPENED
ACEpath Teacher's Diagnosis

You assumed that all applied forces act perpendicular to the lever arm, treating torque simply as force times distance rather than accounting for the angle between the position vector and the force vector.

REASONING PATH
Your ACEpath teacher’s suggested approach
Perpendicular Component Rule
  • Only the component of force perpendicular to the position vector creates torque: τ=rF⊥=rFsin⁡θ\tau = r F_{\perp} = r F \sin\theta.

  • Always check whether the applied force is perpendicular to the lever arm, and multiply by sin⁡θ\sin\theta whenever the angle is not 90∘90^\circ.

CORRECTED PATH
ACEpath Teacher's Demonstration
  1. τ=rFsin⁡θ\tau = r F \sin\theta

  2. τ=(2.40 m)(45.0 N)sin⁡(35.0∘)\tau = (2.40\text{ m})(45.0\text{ N})\sin(35.0^\circ)

  3. τ=(108.0 N⋅m)(0.57358)≈61.9 N⋅m\tau = (108.0\text{ N}\cdot\text{m})(0.57358) \approx 61.9\text{ N}\cdot\text{m}

Final answer

τ=61.9 N⋅m\tau = 61.9\text{ N}\cdot\text{m}, counterclockwise

NEXT STEPS
Final Takeaways from Your Teacher
  • Review the vector definition of torque τ⃗=r⃗×F⃗\vec{\tau} = \vec{r} \times \vec{F} and practice resolving forces into parallel and perpendicular components relative to the lever arm.

  • Work through problems where the force is applied at various non-90∘90^\circ angles to build the habit of checking for the sin⁡θ\sin\theta factor.

OverviewACEpath Teacher's Diagnosis

03 The student misidentifies the direction of rotation, confusing counterclockwise with clockwise rotation produced by an upward force at the right end.

Sample Student Work

Reviewed by ACEpath Teacher
Step-by-Step Review
Walk Through It with Your Teacher
Partially correct
  1. Step 1

    τ=r∗F∗sin⁡(35.0∘)  ⟹  τ=2.40∗45.0∗0.5736=61.9 N⋅m\tau = r * F * \sin(35.0^\circ) \implies \tau = 2.40 * 45.0 * 0.5736 = 61.9\text{ N}\cdot\text{m}

  2. Step 2

    Clockwise

    Correct

    Counterclockwise

    With the pivot at the left end, pulling upward and to the right on the right end lifts the beam upward, which rotates it counterclockwise around the hinge.

WHAT YOU DID WELL
Compliments from Your Teacher

You correctly identified and applied the torque magnitude equation τ=rFsin⁡θ\tau = r F \sin\theta.

You accurately evaluated the trigonometric term and rounded the torque to 61.9 N⋅m61.9\text{ N}\cdot\text{m}.

THE ERROR
Where Your ACEpath Teacher Spotted the Mistake
Rotational sense misidentification

no

WHY IT HAPPENED
ACEpath Teacher's Diagnosis

You confused the rotational direction produced by an upward force applied to the right of a fixed pivot, treating an upward swing as clockwise rather than counterclockwise.

REASONING PATH
Your ACEpath teacher’s suggested approach
Visualize the Pivot as a Clock Center
  • Imagine the beam as a clock hand pointing from the pivot to the point of force application.

  • Place your pencil on the page, pin down the left end with one finger, and push the right end upward in the direction of the force component. Observe that it sweeps upward and to the left (counterclockwise).

CORRECTED PATH
ACEpath Teacher's Demonstration
  1. Decompose the applied force: the horizontal component acts along the beam through the pivot, producing no torque.

  2. The vertical component acts upward at x=+2.40 mx = +2.40\text{ m} relative to the pivot at x=0x = 0.

  3. An upward force on the right side of a fixed pivot causes the beam to rotate upward and to the left, which corresponds to counterclockwise rotation.

Final answer

τ=61.9 N⋅m\tau = 61.9\text{ N}\cdot\text{m}, counterclockwise

NEXT STEPS
Final Takeaways from Your Teacher
  • Practice using the right-hand rule or the pinned-pencil trick to visually confirm the rotational direction before writing down clockwise or counterclockwise.

  • Solve problems where forces act at different quadrants relative to the pivot to build intuition for directional signs.

Lock it in

Similar question

01

A horizontal rod of length 1.50 m1.50\text{ m} is pivoted at its left end. A downward force of 20.0 N20.0\text{ N} is applied at the right end at an angle of 60.0∘60.0^\circ below the horizontal. Calculate the magnitude and direction (clockwise or counterclockwise) of the torque about the pivot.

Answer

τ=26.0 N⋅m\tau = 26.0\text{ N}\cdot\text{m}, clockwise. Key step: The perpendicular component is F⊥=20.0sin⁡(60.0∘)≈17.32 NF_\perp = 20.0\sin(60.0^\circ) \approx 17.32\text{ N}, giving τ=(1.50 m)(17.32 N)≈26.0 N⋅m\tau = (1.50\text{ m})(17.32\text{ N}) \approx 26.0\text{ N}\cdot\text{m}. A downward pull at the right end rotates the rod clockwise.

02

A mechanic pushes on the end of a 0.350 m0.350\text{ m} long wrench with a force of 80.0 N80.0\text{ N}. The force makes an angle of 120.0∘120.0^\circ with the handle of the wrench directed outward. What torque magnitude does the mechanic exert on the bolt?

Answer

τ=24.2 N⋅m\tau = 24.2\text{ N}\cdot\text{m}. Key step: τ=rFsin⁡(120.0∘)=(0.350 m)(80.0 N)sin⁡(120.0∘)=28.0×0.8660≈24.2 N⋅m\tau = r F \sin(120.0^\circ) = (0.350\text{ m})(80.0\text{ N})\sin(120.0^\circ) = 28.0 \times 0.8660 \approx 24.2\text{ N}\cdot\text{m}.

03

A uniform beam of length L=3.00 mL = 3.00\text{ m} and mass 12.0 kg12.0\text{ kg} is hinged to a wall at its left end. In addition to gravity acting at its center of mass, a cable attached to the right end pulls upward and to the left at an angle of 40.0∘40.0^\circ above the horizontal with tension T=70.0 NT = 70.0\text{ N}. Taking g=9.80 m/s2g = 9.80\text{ m/s}^2, calculate the net torque about the hinge and state whether the beam begins to rotate clockwise or counterclockwise.

Answer

τnet=41.4 N⋅m\tau_{\text{net}} = 41.4\text{ N}\cdot\text{m}, clockwise. Key steps: Gravity produces a clockwise torque τg=(1.50 m)(12.0 kg×9.80 m/s2)=176.4 N⋅m\tau_g = (1.50\text{ m})(12.0\text{ kg} \times 9.80\text{ m/s}^2) = 176.4\text{ N}\cdot\text{m}. The cable produces a counterclockwise torque τT=(3.00 m)(70.0 N)sin⁡(40.0∘)≈135.0 N⋅m\tau_T = (3.00\text{ m})(70.0\text{ N})\sin(40.0^\circ) \approx 135.0\text{ N}\cdot\text{m}. Net torque is 176.4−135.0=41.4 N⋅m176.4 - 135.0 = 41.4\text{ N}\cdot\text{m} clockwise.

Loading workspace…