Resources
A block vibrates horizontally in simple harmonic motion along the -axis according to . At , the block is at and moving toward the left (negative -direction) with a velocity . The spring constant is . (a) Compute the elastic potential energy and kinetic energy at . (b) Using the work-energy theorem, calculate the total mechanical work done by the spring on the block as it moves from to the maximum leftward turning point , taking careful note of the algebraic sign.
Answer and steps
Final answer
(a) Potential energy , kinetic energy ; (b) Work done by spring .
Steps
Part (a): Potential and Kinetic Energy at
-
Calculate the elastic potential energy (): The elastic potential energy stored in a spring depends solely on the displacement from the equilibrium position ():
Substituting the given spring constant and position :
-
Calculate the kinetic energy (): The kinetic energy depends on the mass and the instantaneous velocity :
Substituting and :
Part (b): Work Done by the Spring Using the Work-Energy Theorem
- Apply the Work-Energy Theorem: The work-energy theorem states that the net work done on an object equals the change in its kinetic energy:
-
Identify initial and final states:
- Initial state ():
- Final state (): The maximum turning point occurs when the block momentarily comes to rest before reversing direction, so and .
- Compute the work done (): Since the spring force is the only horizontal force acting on the block:
-
Sign Verification and Physical Intuition:
- As the block travels to the left from toward , its displacement vector points in the negative -direction ().
- Because the spring is compressed (), the restoring spring force pushes outward toward the equilibrium position, pointing in the positive -direction ().
- Force and displacement point in opposite directions, confirming that the spring does negative work and extracts kinetic energy from the block to store it as potential energy.
Typical errors
01 The student confuses the work done by the spring with the change in potential energy and omits the negative sign in the work-energy relation, yielding a positive work value of +0.448 J.
Sample Student Work
Reviewed by ACEpath TeacherStep-by-Step Review
Walk Through It with Your Teacher- Step 1
- Step 2
- Step 3
- Step 4Correct
The work-energy theorem defines net work as the change in kinetic energy, which is always final minus initial: . Because the block slows down from to , the change is negative.
WHAT YOU DID WELL
Compliments from Your TeacherYou correctly evaluated the elastic potential energy and kinetic energy at .
You recognized that the block has zero velocity and zero kinetic energy at the turning point.
THE ERROR
Where Your ACEpath Teacher Spotted the MistakeWriting rather than .
WHY IT HAPPENED
ACEpath Teacher's DiagnosisReversing the standard definition of change () when applying the work-energy theorem, which obscures the physical reality that the spring opposes the block's leftward motion and removes kinetic energy.
REASONING PATH
Your ACEpath teacher’s suggested approach- Definition of Change
Any change quantity is always strictly defined as .
Always write explicitly before plugging in values.
- Physical Direction Check
When a force opposes the direction of displacement, it does negative work on the object.
Check that as the block moves further left (), the compressed spring pushes right (), confirming .
CORRECTED PATH
ACEpath Teacher's DemonstrationApply the work-energy theorem using : .
Substitute and : .
(a) , ; (b)
02 The student mistakenly equates the work done by the spring to the total mechanical energy of the system rather than the change in kinetic energy.
Sample Student Work
Reviewed by ACEpath TeacherStep-by-Step Review
Walk Through It with Your Teacher- Step 1
- Step 2
- Step 3Correct
According to the work-energy theorem, the net work done on the block equals its change in kinetic energy (), not the change from zero to total mechanical energy. Since the block comes to rest momentarily at the turning point , , giving .
WHAT YOU DID WELL
Compliments from Your TeacherYou correctly used to find the initial elastic potential energy.
You correctly computed the initial kinetic energy using .
You correctly determined that the work done by the spring must be negative as the block travels toward the maximum compression point.
THE ERROR
Where Your ACEpath Teacher Spotted the Mistakeno
WHY IT HAPPENED
ACEpath Teacher's DiagnosisYou confused the work done by the spring during a segment of motion () with the total mechanical energy of the oscillator (). Because the spring was already compressed at , the spring did work to convert only the remaining kinetic energy into additional potential energy, not the entire total energy from the equilibrium position.
REASONING PATH
Your ACEpath teacher’s suggested approach- Work-Energy Theorem Definition
The net work done on an object equals its change in kinetic energy: .
Always identify the initial kinetic energy and final kinetic energy of the specific interval before finding work.
- Work vs. Potential Energy Difference
For a conservative spring force, .
When using potential energy, subtract the initial potential energy from the final potential energy rather than assuming .
CORRECTED PATH
ACEpath Teacher's DemonstrationApply the work-energy theorem: .
Substitute the values at the turning point: and .
Compute the work: .
03 The student omits squaring the velocity when computing the initial kinetic energy, which then propagates into the work-energy theorem.
Sample Student Work
Reviewed by ACEpath TeacherStep-by-Step Review
Walk Through It with Your Teacher- Step 1
- Step 2Correct
You omitted the square on velocity in the kinetic energy formula. Kinetic energy is defined as , which is always non-negative.
- Step 3
K_f = 0 W_s = K_f - K_i = 0 - (-0.280) W_s = 0.280
CorrectYou correctly recognized that the block stops momentarily at the turning point () and set up the work-energy theorem properly, but substituting your negative value of led to an incorrect positive work value.
WHAT YOU DID WELL
Compliments from Your TeacherYou used the correct expression for elastic potential energy and evaluated it accurately.
You correctly identified that the kinetic energy is zero at the turning point.
You properly set up the work-energy theorem as .
THE ERROR
Where Your ACEpath Teacher Spotted the MistakeYou wrote instead of , leading to an impossible negative kinetic energy of .
WHY IT HAPPENED
ACEpath Teacher's DiagnosisConfusing linear momentum or a linear velocity factor with kinetic energy, and missing the self-check that translational kinetic energy can never be negative.
REASONING PATH
Your ACEpath teacher’s suggested approach- Kinetic Energy Sign Check
For any classical object of mass , kinetic energy is .
Whenever you compute kinetic energy and obtain a negative number, immediately check whether you forgot to square the velocity.
- Physical Sign of Restoring Work
When a spring decelerates a moving mass toward a turning point, force and displacement oppose each other, meaning .
Verify that work done by the spring is negative when it extracts kinetic energy from the block to compress or stretch further.
CORRECTED PATH
ACEpath Teacher's DemonstrationApply the work-energy theorem with :
(a) , ; (b)
Lock it in
How is the work-energy theorem defined in terms of kinetic energy?
. It is always final kinetic energy minus initial kinetic energy, never initial minus final.
Similar question
A cart on a frictionless track compresses a horizontal spring () as it slows from to a complete stop. Using the work-energy theorem, calculate the work done by the spring on the cart.
Answer
. Key steps: , . By the work-energy theorem, .
A block attached to a spring moves from to the equilibrium position . During this motion, its kinetic energy increases from to . Find the work done by the spring and explain its sign.
Answer
. Key steps: . The work is positive because the restoring force pushes rightward () while the block moves rightward toward , speeding it up.
A object oscillates with total mechanical energy . As it travels from a point where to a turning point, compute the work done by the spring using two different methods: (1) the work-energy theorem, and (2) the relation between conservative work and potential energy ().
Answer
. Key steps: (1) At the initial point, . At the turning point, . Thus . (2) At the turning point, . Thus . Therefore .