Resources

An electric generator consists of a flat rectangular coil with N=250 turnsN = 250\text{ turns}, each having dimensions of 12.0 cm×20.0 cm12.0\text{ cm} \times 20.0\text{ cm}. The coil rotates at a constant angular frequency of ω=120π rad/s\omega = 120\pi\text{ rad/s} (60.0 Hz60.0\text{ Hz}) inside a uniform horizontal magnetic field of magnitude B=0.350 TB = 0.350\text{ T}. (a) Calculate the maximum electromotive force (peak emf, E0\mathcal{E}_0) induced in the coil. (b) If the output of this generator is connected across the primary winding of an ideal step-down transformer having Np=1200 turnsN_p = 1200\text{ turns} and Ns=60 turnsN_s = 60\text{ turns}, determine the root-mean-square (rms) voltage delivered across the secondary load.

Answer and steps

Final answer

(a) E0=792 V\mathcal{E}_0 = 792\text{ V}; (b) Vs,rms=28.0 VV_{s,\text{rms}} = 28.0\text{ V}

Steps

Part (a): Calculating the Peak Electromotive Force (E0\mathcal{E}_0)

  1. Calculate the cross-sectional area of the coil (AA): Convert the dimensions of the rectangular coil into standard SI units (meters): A=length×width=(0.120 m)×(0.200 m)=0.0240 m2A = \text{length} \times \text{width} = (0.120\text{ m}) \times (0.200\text{ m}) = 0.0240\text{ m}^2
  2. Apply Faraday's law of electromagnetic induction to an AC generator: As the coil rotates with angular velocity ω\omega in a uniform magnetic field BB, the magnetic flux through a single loop at time tt is: ΦB(t)=BAcos⁡(ωt)\Phi_B(t) = B A \cos(\omega t)

    According to Faraday's law, the induced electromotive force in an NN-turn coil is: E(t)=−NdΦBdt=NBAωsin⁡(ωt)\mathcal{E}(t) = -N \frac{d\Phi_B}{dt} = N B A \omega \sin(\omega t)

  3. Determine the peak emf (E0\mathcal{E}_0): The maximum (peak) value occurs when sin⁡(ωt)=1\sin(\omega t) = 1: E0=NBAω\mathcal{E}_0 = N B A \omega

    Substitute the given numerical values: E0=(250)(0.350 T)(0.0240 m2)(120π rad/s)\mathcal{E}_0 = (250)(0.350\text{ T})(0.0240\text{ m}^2)(120\pi\text{ rad/s}) E0=252π V≈791.7 V≈792 V\mathcal{E}_0 = 252\pi\text{ V} \approx 791.7\text{ V} \approx 792\text{ V}


Part (b): Finding the RMS Voltage Across the Secondary Load (Vs,rmsV_{s,\text{rms}})

  1. Determine the peak voltage across the primary winding (Vp,0V_{p,0}): Because the generator output is connected directly to the primary coil of the transformer: Vp,0=E0≈791.7 VV_{p,0} = \mathcal{E}_0 \approx 791.7\text{ V}
  2. Relate the primary and secondary voltages using the transformer turns ratio: For an ideal transformer, the ratio of the voltages equals the ratio of the turns: VsVp=NsNp\frac{V_s}{V_p} = \frac{N_s}{N_p}

    Therefore, the peak secondary voltage Vs,0V_{s,0} is: Vs,0=Vp,0(NsNp)=(791.7 V)(601200)=(791.7 V)(120)≈39.58 VV_{s,0} = V_{p,0} \left(\frac{N_s}{N_p}\right) = (791.7\text{ V})\left(\frac{60}{1200}\right) = (791.7\text{ V})\left(\frac{1}{20}\right) \approx 39.58\text{ V}

  3. Calculate the root-mean-square (rms) secondary voltage (Vs,rmsV_{s,\text{rms}}): For a sinusoidal alternating voltage, the rms voltage is related to the peak voltage by: Vrms=V02V_{\text{rms}} = \frac{V_0}{\sqrt{2}}

    Applying this to the secondary voltage: Vs,rms=Vs,02=39.58 V2≈28.0 VV_{s,\text{rms}} = \frac{V_{s,0}}{\sqrt{2}} = \frac{39.58\text{ V}}{\sqrt{2}} \approx 28.0\text{ V}

Common Pitfall: Do not confuse the peak voltage (E0\mathcal{E}_0) with the root-mean-square voltage (VrmsV_{\text{rms}}). Household and standard AC ratings are quoted in rms, which is a factor of 1/2≈0.7071/\sqrt{2} \approx 0.707 times the peak value. Applying the turns ratio to the peak voltage and then converting to rms, or converting to rms first and then applying the turns ratio, yields the same result: Vp,rms=791.7 V2≈559.8 V  ⟹  Vs,rms=559.8 V×120=28.0 VV_{p,\text{rms}} = \frac{791.7\text{ V}}{\sqrt{2}} \approx 559.8\text{ V} \implies V_{s,\text{rms}} = 559.8\text{ V} \times \frac{1}{20} = 28.0\text{ V}

Typical errors

OverviewACEpath Teacher's Diagnosis

01 The student forgets to convert the dimensions of the coil from centimeters to meters, resulting in an area that is too large by a factor of 10⁴.

Sample Student Work

Reviewed by ACEpath Teacher
Step-by-Step Review
Walk Through It with Your Teacher
Incorrect
  1. Step 1

    A=12.0×20.0=240 cm2  ⟹  E0=NBAω=(250)(0.350)(240)(120π)≈7.92×106 VA = 12.0 \times 20.0 = 240\text{ cm}^2 \implies E_0 = NBA\omega = (250)(0.350)(240)(120\pi) \approx 7.92 \times 10^6\text{ V}

    Correct

    A=(0.120 m)×(0.200 m)=0.0240 m2  ⟹  E0=NBAω=(250)(0.350)(0.0240)(120π)≈792 VA = (0.120\text{ m}) \times (0.200\text{ m}) = 0.0240\text{ m}^2 \implies \mathcal{E}_0 = NBA\omega = (250)(0.350)(0.0240)(120\pi) \approx 792\text{ V}

    You correctly applied Faraday's formula for the peak emf of a rotating coil, E0=NBAω\mathcal{E}_0 = NBA\omega. However, you substituted the area in cm2\text{cm}^2 rather than the SI base unit m2\text{m}^2. Since 1 cm2=10−4 m21\text{ cm}^2 = 10^{-4}\text{ m}^2, 240 cm2=0.0240 m2240\text{ cm}^2 = 0.0240\text{ m}^2, which yields E0≈792 V\mathcal{E}_0 \approx 792\text{ V}.

  2. Step 2

    Vs,peak=Vp,peak×(NsNp)=(7.917×106)(601200)=395840 VV_{s,\text{peak}} = V_{p,\text{peak}} \times \left(\frac{N_s}{N_p}\right) = (7.917 \times 10^6)\left(\frac{60}{1200}\right) = 395840\text{ V}

    Correct

    Vs,0=E0(NsNp)=(791.7 V)(601200)≈39.58 VV_{s,0} = \mathcal{E}_0\left(\frac{N_s}{N_p}\right) = (791.7\text{ V})\left(\frac{60}{1200}\right) \approx 39.58\text{ V}

    You used the correct transformer turns ratio VsVp=NsNp\frac{V_s}{V_p} = \frac{N_s}{N_p}. Your calculation is mathematically consistent with your peak emf from step 1, but the numerical result is inflated because of the initial unit conversion error.

  3. Step 3

    Vs,rms=Vs,peak2=3958402≈2.80×105 VV_{s,\text{rms}} = \frac{V_{s,\text{peak}}}{\sqrt{2}} = \frac{395840}{\sqrt{2}} \approx 2.80 \times 10^5\text{ V}

    Correct

    Vs,rms=Vs,02=39.58 V2≈28.0 VV_{s,\text{rms}} = \frac{V_{s,0}}{\sqrt{2}} = \frac{39.58\text{ V}}{\sqrt{2}} \approx 28.0\text{ V}

    You correctly related the root-mean-square voltage to the peak voltage using Vrms=V02V_{\text{rms}} = \frac{V_0}{\sqrt{2}}. This step is methodologically sound and only inherits the scale factor error from step 1.

WHAT YOU DID WELL
Compliments from Your Teacher

You correctly recalled and applied the generator peak electromotive force formula E0=NBAω\mathcal{E}_0 = NBA\omega.

You used the ideal transformer turns ratio VsVp=NsNp\frac{V_s}{V_p} = \frac{N_s}{N_p} accurately to step down the primary voltage.

You correctly converted the peak sinusoidal voltage to root-mean-square voltage by dividing by 2\sqrt{2}.

THE ERROR
Where Your ACEpath Teacher Spotted the Mistake
Unit conversion omitted for area

You substituted the area as 240240 directly without converting cm2\text{cm}^2 to m2\text{m}^2.

WHY IT HAPPENED
ACEpath Teacher's Diagnosis

You treated the dimensions as simple numbers in standard formulas without first expressing length in meters, overlooking that converting square centimeters to square meters requires multiplying by 10−410^{-4} (10−2×10−210^{-2} \times 10^{-2}).

REASONING PATH
Your ACEpath teacher’s suggested approach
SI Unit Check Before Formula Substitution
  • Every magnetic and electromagnetic formula involving teslas (1 T=1 N/(A⋅m)1\text{ T} = 1\text{ N}/(\text{A}\cdot\text{m})) requires lengths in meters (m\text{m}) and areas in square meters (m2\text{m}^2).

  • Convert linear dimensions to meters before multiplying: 12.0 cm=0.120 m12.0\text{ cm} = 0.120\text{ m} and 20.0 cm=0.200 m20.0\text{ cm} = 0.200\text{ m}, so A=(0.120)(0.200)=0.0240 m2A = (0.120)(0.200) = 0.0240\text{ m}^2.

CORRECTED PATH
ACEpath Teacher's Demonstration
  1. Convert the dimensions to meters: w=0.120 mw = 0.120\text{ m} and l=0.200 ml = 0.200\text{ m}, giving A=0.0240 m2A = 0.0240\text{ m}^2.

  2. Calculate the peak emf: E0=NBAω=(250)(0.350 T)(0.0240 m2)(120π rad/s)=252π V≈791.7 V≈792 V\mathcal{E}_0 = NBA\omega = (250)(0.350\text{ T})(0.0240\text{ m}^2)(120\pi\text{ rad/s}) = 252\pi\text{ V} \approx 791.7\text{ V} \approx 792\text{ V}.

  3. Find the secondary peak voltage using the turns ratio: Vs,0=E0(NsNp)=791.7 V×601200=791.720≈39.58 VV_{s,0} = \mathcal{E}_0 \left(\frac{N_s}{N_p}\right) = 791.7\text{ V} \times \frac{60}{1200} = \frac{791.7}{20} \approx 39.58\text{ V}.

  4. Convert to secondary rms voltage: Vs,rms=Vs,02=39.58 V2≈28.0 VV_{s,\text{rms}} = \frac{V_{s,0}}{\sqrt{2}} = \frac{39.58\text{ V}}{\sqrt{2}} \approx 28.0\text{ V}.

Final answer

(a) E0=792 V\mathcal{E}_0 = 792\text{ V}; (b) Vs,rms=28.0 VV_{s,\text{rms}} = 28.0\text{ V}

NEXT STEPS
Final Takeaways from Your Teacher
  • Always write down the units explicitly during substitution to spot non-SI units like cm\text{cm} or cm2\text{cm}^2 immediately.

  • Check the physical reasonableness of your final answer: millions of volts from a small 12 cm×20 cm12\text{ cm} \times 20\text{ cm} tabletop generator is an immediate clue that an area conversion was missed.

OverviewACEpath Teacher's Diagnosis

02 The student confuses the generator's rotational frequency f with angular frequency ω, multiplying by 2π again to get an angular frequency of 240π² rad/s.

Sample Student Work

Reviewed by ACEpath Teacher
Step-by-Step Review
Walk Through It with Your Teacher
Incorrect
  1. Step 1

    A=0.120×0.200=0.0240 m2A = 0.120 \times 0.200 = 0.0240\text{ m}^2

  2. Step 2

    ω=2π(120π)=240π2 rad/s\omega = 2\pi(120\pi) = 240\pi^2\text{ rad/s}

    Correct

    ω=120π rad/s\omega = 120\pi\text{ rad/s}

    The problem already gave the angular frequency as ω=120π rad/s\omega = 120\pi\text{ rad/s} (corresponding to linear frequency f=60.0 Hzf = 60.0\text{ Hz}, where ω=2πf=2π(60.0)=120π rad/s\omega = 2\pi f = 2\pi(60.0) = 120\pi\text{ rad/s}). You treated 120π120\pi as linear frequency ff and multiplied by 2π2\pi again.

  3. Step 3

    E0=NBAω=(250)(0.350)(0.0240)(240π2)=504π2 V≈4974 VE_0 = NBA\omega = (250)(0.350)(0.0240)(240\pi^2) = 504\pi^2\text{ V} \approx 4974\text{ V}

    Correct

    E0=NBAω=(250)(0.350 T)(0.0240 m2)(120π rad/s)=252π V≈792 V\mathcal{E}_0 = NBA\omega = (250)(0.350\text{ T})(0.0240\text{ m}^2)(120\pi\text{ rad/s}) = 252\pi\text{ V} \approx 792\text{ V}

    Your peak emf formula E0=NBAω\mathcal{E}_0 = NBA\omega and arithmetic were correct, but the result was inflated because of the incorrect value of ω\omega from Step 2.

  4. Step 4

    Vs,peak=4974×(601200)=248.7 VV_{s,\text{peak}} = 4974 \times \left(\frac{60}{1200}\right) = 248.7\text{ V}

    Correct

    Vs,0=E0(NsNp)=(791.7 V)(601200)=39.58 VV_{s,0} = \mathcal{E}_0\left(\frac{N_s}{N_p}\right) = (791.7\text{ V})\left(\frac{60}{1200}\right) = 39.58\text{ V}

    You correctly applied the ideal transformer voltage equation VsVp=NsNp\frac{V_s}{V_p} = \frac{N_s}{N_p}, carrying forward your previous peak voltage value.

  5. Step 5

    Vs,rms=248.72≈175.9 VV_{s,\text{rms}} = \frac{248.7}{\sqrt{2}} \approx 175.9\text{ V}

    Correct

    Vs,rms=Vs,02=39.58 V2≈28.0 VV_{s,\text{rms}} = \frac{V_{s,0}}{\sqrt{2}} = \frac{39.58\text{ V}}{\sqrt{2}} \approx 28.0\text{ V}

    You used the correct relation between peak voltage and rms voltage (Vrms=V02V_{\text{rms}} = \frac{V_0}{\sqrt{2}}), with the error tracing entirely back to Step 2.

WHAT YOU DID WELL
Compliments from Your Teacher

You correctly converted the rectangular dimensions to find the coil area in square meters.

You selected the correct formula E0=NBAω\mathcal{E}_0 = NBA\omega for the peak induced electromotive force.

You accurately applied the ideal transformer turns ratio to relate primary and secondary voltages.

You correctly converted peak alternating voltage to root-mean-square voltage by dividing by 2\sqrt{2}.

THE ERROR
Where Your ACEpath Teacher Spotted the Mistake
Angular frequency double-conversion error

Multiplying ω=120π rad/s\omega = 120\pi\text{ rad/s} by 2π2\pi to get 240π2 rad/s240\pi^2\text{ rad/s}.

WHY IT HAPPENED
ACEpath Teacher's Diagnosis

You confused angular frequency ω\omega (measured in rad/s\text{rad/s}) with ordinary rotational frequency ff (measured in Hz\text{Hz} or s−1\text{s}^{-1}). When a rate is already stated with symbol ω\omega or units of rad/s\text{rad/s}, the factor of 2π2\pi is already included.

REASONING PATH
Your ACEpath teacher’s suggested approach
Unit Inspection
  • Linear frequency ff has units of Hz\text{Hz} or rev/s\text{rev/s}, whereas angular frequency ω\omega has units of rad/s\text{rad/s}.

  • Check the given units before applying ω=2πf\omega = 2\pi f; if the value already has rad/s\text{rad/s}, use it directly as ω\omega.

Peak vs. RMS Timing in Transformers
  • Because an ideal transformer scales voltages linearly (Vs/Vp=Ns/NpV_s / V_p = N_s / N_p), you can convert peak to rms either before or after applying the turns ratio: Vs,rms=Vp,rms(Ns/Np)V_{s,\text{rms}} = V_{p,\text{rms}}(N_s / N_p).

  • Always verify whether your transformer input is peak or rms, and convert at the most convenient stage.

CORRECTED PATH
ACEpath Teacher's Demonstration
  1. Use the given angular frequency directly: ω=120π rad/s≈377.0 rad/s\omega = 120\pi\text{ rad/s} \approx 377.0\text{ rad/s}.

  2. Calculate the peak emf: E0=NBAω=(250)(0.350)(0.0240)(120π)=252π V≈791.7 V\mathcal{E}_0 = NBA\omega = (250)(0.350)(0.0240)(120\pi) = 252\pi\text{ V} \approx 791.7\text{ V}.

  3. Find the secondary peak voltage using the turns ratio: Vs,0=E0(NsNp)=791.7×601200=39.58 VV_{s,0} = \mathcal{E}_0 \left(\frac{N_s}{N_p}\right) = 791.7 \times \frac{60}{1200} = 39.58\text{ V}.

  4. Calculate the secondary rms voltage: Vs,rms=Vs,02=39.582≈28.0 VV_{s,\text{rms}} = \frac{V_{s,0}}{\sqrt{2}} = \frac{39.58}{\sqrt{2}} \approx 28.0\text{ V}.

Final answer

(a) E0=792 V\mathcal{E}_0 = 792\text{ V}; (b) Vs,rms=28.0 VV_{s,\text{rms}} = 28.0\text{ V}

NEXT STEPS
Final Takeaways from Your Teacher
  • Always inspect the units of given rotational speeds: if you see rad/s\text{rad/s}, you already have ω\omega; if you see Hz\text{Hz} or rpm\text{rpm}, multiply by 2π2\pi (and convert minutes to seconds if needed).

  • Practice working with coupled generator-transformer systems to build confidence tracking peak versus rms values.

OverviewACEpath Teacher's Diagnosis

03 The student treats the peak voltage directly as the rms voltage, failing to divide the secondary peak voltage by √2 to find the rms value.

Sample Student Work

Reviewed by ACEpath Teacher
Step-by-Step Review
Walk Through It with Your Teacher
Partially correct
  1. Step 1

    A=0.120×0.200=0.0240 m2  ⟹  E0=NBAω=(250)(0.350)(0.0240)(120π)=252π V≈792 VA = 0.120 \times 0.200 = 0.0240\text{ m}^2 \implies E_0 = NBA\omega = (250)(0.350)(0.0240)(120\pi) = 252\pi\text{ V} \approx 792\text{ V}

  2. Step 2

    Vs=Vp×(NsNp)  ⟹  Vs=792×(601200)=39.6 VV_s = V_p \times \left(\frac{N_s}{N_p}\right) \implies V_s = 792 \times \left(\frac{60}{1200}\right) = 39.6\text{ V}

  3. Step 3

    Vs,rms=39.6 VV_{s,\text{rms}} = 39.6\text{ V}

    Correct

    Vs,rms=Vs,02=39.6 V2≈28.0 VV_{s,\text{rms}} = \frac{V_{s,0}}{\sqrt{2}} = \frac{39.6\text{ V}}{\sqrt{2}} \approx 28.0\text{ V}

    The value 39.6 V39.6\text{ V} is the peak secondary voltage (Vs,0V_{s,0}), not the root-mean-square voltage. For a sinusoidal AC signal, you need to divide the peak value by 2\sqrt{2}.

WHAT YOU DID WELL
Compliments from Your Teacher

You correctly calculated the cross-sectional area in SI units.

You used the correct peak emf formula for a rotating AC generator.

You set up and evaluated the transformer turns ratio accurately.

THE ERROR
Where Your ACEpath Teacher Spotted the Mistake
Peak vs. RMS Confusion

no

WHY IT HAPPENED
ACEpath Teacher's Diagnosis

You treated the peak output voltage from the transformer as the root-mean-square (rms) voltage without applying the sinusoidal conversion factor Vrms=V02V_{\text{rms}} = \frac{V_0}{\sqrt{2}}.

REASONING PATH
Your ACEpath teacher’s suggested approach
Peak vs. RMS in Sinusoidal AC
  • For sinusoidal alternating voltage, the peak amplitude V0V_0 relates to the effective rms voltage by Vrms=V02≈0.707V0V_{\text{rms}} = \frac{V_0}{\sqrt{2}} \approx 0.707 V_0.

  • Always check whether an AC question asks for peak voltage (V0V_0) or rms voltage (VrmsV_{\text{rms}}), and divide sinusoidal peak values by 2\sqrt{2} when finding rms.

CORRECTED PATH
ACEpath Teacher's Demonstration
  1. Recognize that the calculated secondary voltage is the peak amplitude: Vs,0=39.58 VV_{s,0} = 39.58\text{ V}.

  2. Apply the sinusoidal conversion formula: Vs,rms=Vs,02=39.58 V2≈28.0 VV_{s,\text{rms}} = \frac{V_{s,0}}{\sqrt{2}} = \frac{39.58\text{ V}}{\sqrt{2}} \approx 28.0\text{ V}.

Final answer

(a) E0=792 V\mathcal{E}_0 = 792\text{ V}; (b) Vs,rms=28.0 VV_{s,\text{rms}} = 28.0\text{ V}

NEXT STEPS
Final Takeaways from Your Teacher
  • Practice identifying whether given AC voltages are peak or rms before substituting them into circuit equations.

  • Remember that you can convert to rms at the primary side first (Vp,rms=7922V_{p,\text{rms}} = \frac{792}{\sqrt{2}}) or at the secondary side last (Vs,rms=Vs,02V_{s,\text{rms}} = \frac{V_{s,0}}{\sqrt{2}}) with identical results.

Lock it in

Similar question

01

A square coil of side length 8.0 cm8.0\text{ cm} has 150 turns150\text{ turns} and rotates at ω=100 rad/s\omega = 100\text{ rad/s} in a uniform magnetic field of B=0.25 TB = 0.25\text{ T}. Calculate the peak electromotive force E0\mathcal{E}_0 induced in the coil.

Answer

E0=24 V\mathcal{E}_0 = 24\text{ V}. Key steps: A=(0.080 m)2=0.0064 m2A = (0.080\text{ m})^2 = 0.0064\text{ m}^2; then E0=NBAω=(150)(0.25 T)(0.0064 m2)(100 rad/s)=24 V\mathcal{E}_0 = NBA\omega = (150)(0.25\text{ T})(0.0064\text{ m}^2)(100\text{ rad/s}) = 24\text{ V}.

02

A circular generator coil has radius r=5.0 cmr = 5.0\text{ cm} and N=400 turnsN = 400\text{ turns}. It rotates at f=50 Hzf = 50\text{ Hz} in a field of B=0.40 TB = 0.40\text{ T}. The generator's output is connected to an ideal transformer with Np=500N_p = 500 and Ns=100N_s = 100. Find the peak voltage Vs,0V_{s,0} across the secondary coil.

Answer

Vs,0≈79.0 VV_{s,0} \approx 79.0\text{ V}. Key steps: ω=2πf=100π rad/s\omega = 2\pi f = 100\pi\text{ rad/s}; A=πr2=π(0.050 m)2=0.0025π m2A = \pi r^2 = \pi (0.050\text{ m})^2 = 0.0025\pi\text{ m}^2; E0=NBAω=400(0.40)(0.0025π)(100π)=40π2 V≈394.8 V\mathcal{E}_0 = NBA\omega = 400(0.40)(0.0025\pi)(100\pi) = 40\pi^2\text{ V} \approx 394.8\text{ V}; Vs,0=E0(NsNp)=394.8 V×100500≈79.0 VV_{s,0} = \mathcal{E}_0 \left(\frac{N_s}{N_p}\right) = 394.8\text{ V} \times \frac{100}{500} \approx 79.0\text{ V}.

03

An AC generator with a rectangular coil of 10.0 cm×15.0 cm10.0\text{ cm} \times 15.0\text{ cm} and N=300 turnsN = 300\text{ turns} produces a peak emf of E0=120 V\mathcal{E}_0 = 120\text{ V} when rotating at ω=60π rad/s\omega = 60\pi\text{ rad/s}. The generator is linked to a transformer with turns ratio Np:Ns=8:1N_p : N_s = 8 : 1. Determine (a) the magnetic field strength BB and (b) the secondary root-mean-square voltage Vs,rmsV_{s,\text{rms}}.

Answer

(a) B≈0.141 TB \approx 0.141\text{ T}; (b) Vs,rms≈10.6 VV_{s,\text{rms}} \approx 10.6\text{ V}. Key steps: A=0.100 m×0.150 m=0.0150 m2A = 0.100\text{ m} \times 0.150\text{ m} = 0.0150\text{ m}^2; B=E0NAω=120(300)(0.0150)(60π)=120270π≈0.141 TB = \frac{\mathcal{E}_0}{NA\omega} = \frac{120}{(300)(0.0150)(60\pi)} = \frac{120}{270\pi} \approx 0.141\text{ T}; Vs,0=120 V8=15.0 VV_{s,0} = \frac{120\text{ V}}{8} = 15.0\text{ V}; Vs,rms=15.0 V2≈10.6 VV_{s,\text{rms}} = \frac{15.0\text{ V}}{\sqrt{2}} \approx 10.6\text{ V}.

Loading workspace…