Resources
A non-uniform thin rod of total length lies along the -axis from to . Its linear mass density varies as a function of position according to , where and . (a) Derive the general expression for the moment of inertia about a perpendicular axis through the end in terms of , , and using calculus (). (b) Evaluate for (uniform rod), (linearly increasing density), and find the asymptotic limit of the fraction as , where is the total mass of the rod.
Answer and steps
Final answer
(a) ; (b) For , ; for , ; as , .
Steps
Part (a): Derivation of the Moment of Inertia
The moment of inertia of a one-dimensional body about a given axis is obtained by integrating the square of the perpendicular distance from the axis, , multiplied by an infinitesimal mass element :
Setting up the integral from to :
Factor out the constants:
Apply the power rule for integration :
Part (b): Numerical Evaluations and Asymptotic Limit
- Uniform rod (): Substitute , , and :
- Linearly increasing density (): Substitute , , and :
-
Total mass and the ratio : The total mass of the rod is found by integrating the mass density over its length:
Express the ratio :
- Asymptotic limit as : Divide the numerator and denominator by :
Physical insight: As , the density becomes negligibly small everywhere along the rod except directly at the outer edge . Consequently, all of the mass becomes concentrated at distance from the pivot, behaving dynamically like a single point mass with moment of inertia .
Typical errors
01 The student sets up the moment of inertia integral with x instead of x² as the distance weighting, confusing moment of inertia with the center-of-mass numerator.
Sample Student Work
Reviewed by ACEpath TeacherStep-by-Step Review
Walk Through It with Your Teacher- Step 1Correct
You weighted each mass element by distance instead of distance squared . The moment of inertia is defined as , so the integrand must contain , which yields .
- Step 2Correct
You evaluated your derived formula correctly for both values of , but the numerical results are affected by the missing factor of in Step 1.
- Step 3
- Step 4Correct
Your limit technique is sound, but your ratio contains an uncancelled factor of because had incorrect dimensions of mass times length rather than mass times length squared.
WHAT YOU DID WELL
Compliments from Your TeacherYou factored out constants and applied the calculus power rule for integration accurately.
You evaluated the total mass of the non-uniform rod perfectly.
You correctly simplified rational expressions involving and evaluated the asymptotic limit as .
THE ERROR
Where Your ACEpath Teacher Spotted the MistakeYou wrote instead of in the moment of inertia integral.
WHY IT HAPPENED
ACEpath Teacher's DiagnosisYou confused the definition of moment of inertia (, the second moment of mass) with the numerator used to find the center of mass (, the first moment of mass). A quick dimensional check reveals that has units of , while rotational inertia must always have units of .
REASONING PATH
Your ACEpath teacher’s suggested approach- Check Distance Power vs. Quantity
Total mass uses ; center-of-mass numerator uses ; moment of inertia uses .
Always verify that every moment of inertia integral includes before integrating.
- Perform a Dimensional Consistency Check
The SI units of moment of inertia must be .
Check the units of your final symbolic expression: gives .
CORRECTED PATH
ACEpath Teacher's DemonstrationSubstitute into to get .
Integrate using the power rule: .
Substitute : .
Substitute : .
Compute the ratio: .
Evaluate the limit: .
(a) ; (b) For , ; for , ; as , .
02 The student integrates x^(n+2) incorrectly by forgetting to increase the power and dividing by n+2 instead of n+3, resulting in I_0 = λ_0 L³ / (n + 2).
Sample Student Work
Reviewed by ACEpath TeacherStep-by-Step Review
Walk Through It with Your Teacher- Step 1
- Step 2Correct
When integrating , the power rule requires dividing by the new exponent , not .
- Step 3
For : ; For :
CorrectFor : ; For :
Your arithmetic is correct, but your numerical evaluations carry forward the incorrect denominator from Step 2.
- Step 4Correct
You correctly determined the total mass and calculated the limit of your ratio as , but the intermediate ratio was affected by using instead of .
WHAT YOU DID WELL
Compliments from Your TeacherYou set up the integral for the moment of inertia accurately.
You correctly integrated to find the total mass expression .
You evaluated the limit of a rational function as correctly.
THE ERROR
Where Your ACEpath Teacher Spotted the MistakeYou increased the power from to in the numerator, but mistakenly wrote the old power in the denominator.
WHY IT HAPPENED
ACEpath Teacher's DiagnosisFailing to match the denominator divisor to the updated exponent when applying to an expression with an algebraic exponent.
REASONING PATH
Your ACEpath teacher’s suggested approach- Power Rule Exponent and Divisor Match
For any power (with ), the denominator must always match the new exponent exactly.
Before simplifying or taking limits of integration, write down simultaneously in both the exponent and the denominator.
- Sanity Check with Known Uniform Rod Value
For a uniform rod (), the moment of inertia about one end must equal .
Substitute into your derived general formula: if it gives instead of , re-check the power in your integration.
CORRECTED PATH
ACEpath Teacher's DemonstrationApply the power rule to : .
Multiply by : .
For : .
For : .
Form the ratio: .
Evaluate the limit: .
(a) ; (b) For , ; for , ; as , .
03 The student miscalculates the total mass M by assuming it is simply λ_0 L for all n, leading to an incorrect ratio and an asymptotic limit of 0.
Sample Student Work
Reviewed by ACEpath TeacherStep-by-Step Review
Walk Through It with Your Teacher- Step 1
- Step 2
- Step 3Correct
Because the density varies along the rod, you must integrate to find the total mass as a function of , rather than multiplying the maximum density by .
- Step 4Correct
Your algebraic ratio and limit calculation followed consistently from your incorrect expression for .
WHAT YOU DID WELL
Compliments from Your TeacherYou correctly formulated the moment of inertia integral with the variable mass density .
You applied the power rule of integration accurately to determine as a function of .
You evaluated the numerical values of correctly for and .
THE ERROR
Where Your ACEpath Teacher Spotted the Mistakeno
WHY IT HAPPENED
ACEpath Teacher's DiagnosisYou assumed that the total mass equals , which only applies to a uniform rod (). For any non-uniform mass distribution, total mass depends on and must be found by integrating .
REASONING PATH
Your ACEpath teacher’s suggested approach- Total Mass of a Non-Uniform Body
For a one-dimensional body with position-dependent density , the total mass is , not .
Always set up an integral over the object's length whenever density is a function of position.
- Physical Limiting Behavior
As , vanishes everywhere except near , concentrating all mass at distance from the pivot.
Check whether the asymptotic ratio matches the point-mass limit of .
CORRECTED PATH
ACEpath Teacher's DemonstrationCalculate total mass by integrating : .
Form the dimensionless ratio: .
Evaluate the asymptotic limit as : .
Lock it in
What is the defining integral for the moment of inertia of a continuous body about a given rotation axis?
, where is the perpendicular distance from each mass element to the axis of rotation. Memory cue: Inertia scales with distance squared (), not linear distance ().
Similar question
A thin rod of length and uniform linear density lies along the -axis from to . Using calculus, calculate its moment of inertia about an axis perpendicular to the rod through the end in terms of its total mass and length .
Answer
. Key steps: , so . Then .
A non-uniform thin rod of length has linear mass density , where , for . Find both the total mass of the rod and its moment of inertia about a perpendicular axis through .
Answer
and . Key steps: . Moment of inertia: .
A thin rod of length and total mass has mass density for , where is a constant. (a) Express in terms of and . (b) Determine the moment of inertia about the axis at in terms of and .
Answer
(a) ; (b) . Key steps: . Then .