Resources

A wrench of length r=0.400 mr = 0.400\text{ m} is aligned along the positive xx-axis with its socket at the origin (0,0)(0, 0). A constant force F⃗\vec{F} of magnitude F0=120 NF_0 = 120\text{ N} acts at the right tip (0.400,0) m(0.400, 0)\text{ m} in the xyxy-plane at an angle ϕ\phi with respect to the wrench axis. Write the torque magnitude τ\tau as a function of ϕ\phi. Evaluate τ\tau for ϕ1=1.00∘\phi_1 = 1.00^\circ, ϕ2=0.100∘\phi_2 = 0.100^\circ, and find the limiting value of dτdϕ\frac{d\tau}{d\phi} as ϕ→0\phi \to 0 in units of N⋅m/rad\text{N}\cdot\text{m/rad}.

Answer and steps

Final answer

τ(1.00∘)=0.838 N⋅m\tau(1.00^\circ) = 0.838\text{ N}\cdot\text{m}, τ(0.100∘)=0.0838 N⋅m\tau(0.100^\circ) = 0.0838\text{ N}\cdot\text{m}, lim⁡ϕ→0dτdϕ=48.0 N⋅m/rad\lim_{\phi \to 0}\frac{d\tau}{d\phi} = 48.0\text{ N}\cdot\text{m/rad}

Steps

01

General Expression for Torque

The magnitude of torque τ\tau produced by a force F⃗\vec{F} applied at a position vector r⃗\vec{r} relative to the pivot is given by the cross product magnitude:

τ=∣r⃗×F⃗∣=rF0sin⁡ϕ\tau = |\vec{r} \times \vec{F}| = r F_0 \sin\phi

Given:

  • Lever arm distance from pivot: r=0.400 mr = 0.400\text{ m}
  • Force magnitude: F0=120 NF_0 = 120\text{ N}

Substitute these values to obtain τ\tau as a function of the angle ϕ\phi:

τ(ϕ)=(0.400 m)(120 N)sin⁡ϕ=48.0sin⁡ϕ N⋅m\tau(\phi) = (0.400\text{ m})(120\text{ N})\sin\phi = 48.0\sin\phi\text{ N}\cdot\text{m}


02

Evaluation at Specific Angles

  • For ϕ1=1.00∘\phi_1 = 1.00^\circ:

    τ(1.00∘)=48.0sin⁡(1.00∘)≈48.0×0.0174524≈0.838 N⋅m\tau(1.00^\circ) = 48.0 \sin(1.00^\circ) \approx 48.0 \times 0.0174524 \approx 0.838\text{ N}\cdot\text{m}

  • For ϕ2=0.100∘\phi_2 = 0.100^\circ:

    τ(0.100∘)=48.0sin⁡(0.100∘)≈48.0×0.00174533≈0.0838 N⋅m\tau(0.100^\circ) = 48.0 \sin(0.100^\circ) \approx 48.0 \times 0.00174533 \approx 0.0838\text{ N}\cdot\text{m}

Common Pitfall: When evaluating trigonometric functions on a calculator, ensure the angle mode is set to degrees when entering values in degrees, or convert the angle into radians (ϕ rad=ϕ∘×π180∘\phi\text{ rad} = \phi^\circ \times \frac{\pi}{180^\circ}) before calculation.


03

Rate of Change of Torque with Respect to Angle

When differentiating with respect to an angle measured in radians, the derivative of sin⁡ϕ\sin\phi is cos⁡ϕ\cos\phi:

dτdϕ=ddϕ(rF0sin⁡ϕ)=rF0cos⁡ϕ\frac{d\tau}{d\phi} = \frac{d}{d\phi}(r F_0 \sin\phi) = r F_0 \cos\phi

Taking the limit as ϕ→0\phi \to 0:

lim⁡ϕ→0dτdϕ=rF0cos⁡(0)=rF0=48.0 N⋅m/rad\lim_{\phi \to 0} \frac{d\tau}{d\phi} = r F_0 \cos(0) = r F_0 = 48.0\text{ N}\cdot\text{m/rad}

This shows that for small angles in radians (sin⁡ϕ≈ϕ\sin\phi \approx \phi), the torque grows linearly at an initial rate of 48.0 N⋅m48.0\text{ N}\cdot\text{m} per radian.

Typical errors

OverviewACEpath Teacher's Diagnosis

01 The student confuses the cross product for torque with the dot product for work, using cosine instead of sine for the torque magnitude.

Sample Student Work

Reviewed by ACEpath Teacher
Step-by-Step Review
Walk Through It with Your Teacher
Incorrect
  1. Step 1

    τ(ϕ)=rF0cos⁡ϕ  ⟹  τ(ϕ)=(0.400)(120)cos⁡ϕ=48.0cos⁡ϕ N⋅m\tau(\phi) = r F_0 \cos\phi \implies \tau(\phi) = (0.400)(120)\cos\phi = 48.0\cos\phi\text{ N}\cdot\text{m}

    Correct

    τ(ϕ)=rF0sin⁡ϕ=(0.400 m)(120 N)sin⁡ϕ=48.0sin⁡ϕ N⋅m\tau(\phi) = r F_0 \sin\phi = (0.400\text{ m})(120\text{ N})\sin\phi = 48.0\sin\phi\text{ N}\cdot\text{m}

    You correctly substituted the numerical values r=0.400 mr = 0.400\text{ m} and F0=120 NF_0 = 120\text{ N}, but torque magnitude comes from the cross product ∣r⃗×F⃗∣=rF0sin⁡ϕ|\vec{r} \times \vec{F}| = r F_0 \sin\phi, not cos⁡ϕ\cos\phi.

  2. Step 2

    τ(1.00∘)=48.0cos⁡(1.00∘) N⋅m=48.0 N⋅m  ⟹  τ(0.100∘)=48.0cos⁡(0.100∘) N⋅m=48.0 N⋅m\tau(1.00^\circ) = 48.0\cos(1.00^\circ)\text{ N}\cdot\text{m} = 48.0\text{ N}\cdot\text{m} \implies \tau(0.100^\circ) = 48.0\cos(0.100^\circ)\text{ N}\cdot\text{m} = 48.0\text{ N}\cdot\text{m}

    Correct

    τ(1.00∘)=48.0sin⁡(1.00∘)≈0.838 N⋅m  ⟹  τ(0.100∘)=48.0sin⁡(0.100∘)≈0.0838 N⋅m\tau(1.00^\circ) = 48.0\sin(1.00^\circ)\approx 0.838\text{ N}\cdot\text{m} \implies \tau(0.100^\circ) = 48.0\sin(0.100^\circ)\approx 0.0838\text{ N}\cdot\text{m}

    Your evaluation follows logically from your expression in Step 1, but it is affected by using cos⁡ϕ\cos\phi. Notice that pulling almost parallel to a wrench (ϕ→0\phi \to 0) should produce nearly zero torque, rather than the maximum torque.

  3. Step 3

    dτdϕ=−48.0sin⁡ϕ  ⟹  lim⁡ϕ→0dτdϕ=−48.0sin⁡(0)=0 N⋅m/rad\frac{d\tau}{d\phi} = -48.0\sin\phi \implies \lim_{\phi \to 0}\frac{d\tau}{d\phi} = -48.0\sin(0) = 0\text{ N}\cdot\text{m/rad}

    Correct

    dτdϕ=48.0cos⁡ϕ  ⟹  lim⁡ϕ→0dτdϕ=48.0cos⁡(0)=48.0 N⋅m/rad\frac{d\tau}{d\phi} = 48.0\cos\phi \implies \lim_{\phi \to 0}\frac{d\tau}{d\phi} = 48.0\cos(0) = 48.0\text{ N}\cdot\text{m/rad}

    Your differentiation of cos⁡ϕ\cos\phi was mathematically sound, but because the true torque function is τ(ϕ)=48.0sin⁡ϕ\tau(\phi) = 48.0\sin\phi, the derivative is dτdϕ=48.0cos⁡ϕ\frac{d\tau}{d\phi} = 48.0\cos\phi.

WHAT YOU DID WELL
Compliments from Your Teacher

You correctly identified that the lever arm is r=0.400 mr = 0.400\text{ m} and the applied force is F0=120 NF_0 = 120\text{ N}.

You accurately computed the product rF0=48.0 N⋅mr F_0 = 48.0\text{ N}\cdot\text{m}.

You correctly differentiated your chosen trigonometric function and evaluated the limit as ϕ→0\phi \to 0.

THE ERROR
Where Your ACEpath Teacher Spotted the Mistake
Trigonometric function mix-up in cross product

no

WHY IT HAPPENED
ACEpath Teacher's Diagnosis

You used the cosine function instead of the sine function for torque magnitude, confusing the cross-product definition of torque (∥r⃗×F⃗∥=rFsin⁡ϕ\|\vec{r} \times \vec{F}\| = r F \sin\phi) with the dot-product definition of work (W=F⃗⋅d⃗=Fdcos⁡θW = \vec{F} \cdot \vec{d} = F d \cos\theta).

REASONING PATH
Your ACEpath teacher’s suggested approach
Torque uses the perpendicular component
  • τ=∣r⃗×F⃗∣=rFsin⁡ϕ\tau = |\vec{r} \times \vec{F}| = r F \sin\phi, where ϕ\phi is the angle between r⃗\vec{r} and F⃗\vec{F}.

  • Always verify extreme angles physically: when ϕ=0∘\phi = 0^\circ (pulling directly along the wrench handle), there is no rotational tendency, so τ\tau must be 00, requiring sin⁡(0∘)=0\sin(0^\circ) = 0.

CORRECTED PATH
ACEpath Teacher's Demonstration
  1. Write the torque definition using the cross-product magnitude: τ(ϕ)=rF0sin⁡ϕ\tau(\phi) = r F_0 \sin\phi.

  2. Substitute r=0.400 mr = 0.400\text{ m} and F0=120 NF_0 = 120\text{ N} to get τ(ϕ)=48.0sin⁡ϕ N⋅m\tau(\phi) = 48.0\sin\phi\text{ N}\cdot\text{m}.

  3. Evaluate at ϕ1=1.00∘\phi_1 = 1.00^\circ: τ(1.00∘)=48.0sin⁡(1.00∘)≈0.838 N⋅m\tau(1.00^\circ) = 48.0\sin(1.00^\circ) \approx 0.838\text{ N}\cdot\text{m}.

  4. Evaluate at ϕ2=0.100∘\phi_2 = 0.100^\circ: τ(0.100∘)=48.0sin⁡(0.100∘)≈0.0838 N⋅m\tau(0.100^\circ) = 48.0\sin(0.100^\circ) \approx 0.0838\text{ N}\cdot\text{m}.

  5. Differentiate with respect to ϕ\phi in radians: dτdϕ=48.0cos⁡ϕ N⋅m/rad\frac{d\tau}{d\phi} = 48.0\cos\phi\text{ N}\cdot\text{m/rad}.

  6. Take the limit as ϕ→0\phi \to 0: lim⁡ϕ→048.0cos⁡ϕ=48.0 N⋅m/rad\lim_{\phi \to 0} 48.0\cos\phi = 48.0\text{ N}\cdot\text{m/rad}.

Final answer

τ(1.00∘)=0.838 N⋅m\tau(1.00^\circ) = 0.838\text{ N}\cdot\text{m}, τ(0.100∘)=0.0838 N⋅m\tau(0.100^\circ) = 0.0838\text{ N}\cdot\text{m}, lim⁡ϕ→0dτdϕ=48.0 N⋅m/rad\lim_{\phi \to 0}\frac{d\tau}{d\phi} = 48.0\text{ N}\cdot\text{m/rad}

NEXT STEPS
Final Takeaways from Your Teacher
  • Remember that cross products measure perpendicularity and use sine, while dot products measure alignment and use cosine.

  • Perform a quick physical boundary check at ϕ=0∘\phi = 0^\circ and ϕ=90∘\phi = 90^\circ before proceeding to calculations.

OverviewACEpath Teacher's Diagnosis

02 The student evaluates trigonometric functions while keeping the calculator in radian mode instead of degree mode for the given degree angles.

Sample Student Work

Reviewed by ACEpath Teacher
Step-by-Step Review
Walk Through It with Your Teacher
Partially correct
  1. Step 1

    τ(ϕ)=rF0sin⁡ϕ=(0.400)(120)sin⁡ϕ=48.0sin⁡ϕ N⋅m\tau(\phi) = r F_0 \sin\phi = (0.400)(120)\sin\phi = 48.0\sin\phi\text{ N}\cdot\text{m}

  2. Step 2

    τ(1.00∘)=48.0sin⁡(1.00)=40.4 N⋅m\tau(1.00^\circ) = 48.0\sin(1.00) = 40.4\text{ N}\cdot\text{m}

    Correct

    τ(1.00∘)=48.0sin⁡(1.00∘)≈0.838 N⋅m\tau(1.00^\circ) = 48.0\sin(1.00^\circ) \approx 0.838\text{ N}\cdot\text{m}

    You entered 1.001.00 as radians into your calculator rather than degrees. Because sin⁡(1.00∘)≈0.01745\sin(1.00^\circ) \approx 0.01745, the torque is 48.0×0.01745≈0.838 N⋅m48.0 \times 0.01745 \approx 0.838\text{ N}\cdot\text{m}.

  3. Step 3

    τ(0.100∘)=48.0sin⁡(0.100)=4.79 N⋅m\tau(0.100^\circ) = 48.0\sin(0.100) = 4.79\text{ N}\cdot\text{m}

    Correct

    τ(0.100∘)=48.0sin⁡(0.100∘)≈0.0838 N⋅m\tau(0.100^\circ) = 48.0\sin(0.100^\circ) \approx 0.0838\text{ N}\cdot\text{m}

    You computed sin⁡(0.100 rad)\sin(0.100\text{ rad}) instead of sin⁡(0.100∘)\sin(0.100^\circ). In degrees, sin⁡(0.100∘)≈0.001745\sin(0.100^\circ) \approx 0.001745, giving τ≈0.0838 N⋅m\tau \approx 0.0838\text{ N}\cdot\text{m}.

  4. Step 4

    dτdϕ=48.0cos⁡ϕ  ⟹  lim⁡ϕ→0dτdϕ=48.0cos⁡(0)=48.0 N⋅m/rad\frac{d\tau}{d\phi} = 48.0\cos\phi \implies \lim_{\phi \to 0}\frac{d\tau}{d\phi} = 48.0\cos(0) = 48.0\text{ N}\cdot\text{m/rad}

WHAT YOU DID WELL
Compliments from Your Teacher

You correctly established the cross product magnitude formula for torque, τ(ϕ)=rF0sin⁡ϕ\tau(\phi) = r F_0 \sin\phi.

You correctly recognized that calculus derivatives of trigonometric functions require angle arguments in radians, yielding the correct rate of change of 48.0 N⋅m/rad48.0\text{ N}\cdot\text{m/rad}.

THE ERROR
Where Your ACEpath Teacher Spotted the Mistake
Angle Unit Mismatch (Degrees vs. Radians)

You dropped the degree symbol (∘^\circ) when entering values into your calculator, evaluating sin⁡(1.00 rad)\sin(1.00\text{ rad}) and sin⁡(0.100 rad)\sin(0.100\text{ rad}) instead of sin⁡(1.00∘)\sin(1.00^\circ) and sin⁡(0.100∘)\sin(0.100^\circ).

WHY IT HAPPENED
ACEpath Teacher's Diagnosis

Treating degree inputs directly as dimensionless real numbers without switching your calculator to degree mode or multiplying by the conversion factor π180∘\frac{\pi}{180^\circ}.

REASONING PATH
Your ACEpath teacher’s suggested approach
Calculator Mode Check
  • Always verify the angle setting (DEG vs. RAD) before evaluating trigonometric expressions.

  • If an angle is given with a degree symbol ∘^\circ, ensure your calculator is in degree mode or convert to radians via ϕrad=ϕ∘×π180∘\phi_\text{rad} = \phi^\circ \times \frac{\pi}{180^\circ}.

Small-Angle Sanity Check
  • For small angles in degrees, sin⁡(θ∘)≈θ×π180≈0.0175 θ\sin(\theta^\circ) \approx \theta \times \frac{\pi}{180} \approx 0.0175\,\theta.

  • Notice that 1∘1^\circ is a tiny fraction of a circle, so sin⁡(1∘)\sin(1^\circ) must be much closer to 0.0170.017 than to sin⁡(1 rad)≈0.84\sin(1\text{ rad}) \approx 0.84.

CORRECTED PATH
ACEpath Teacher's Demonstration
  1. τ(1.00∘)=48.0sin⁡(1.00∘)=48.0×0.0174524≈0.838 N⋅m\tau(1.00^\circ) = 48.0\sin(1.00^\circ) = 48.0 \times 0.0174524 \approx 0.838\text{ N}\cdot\text{m}

  2. τ(0.100∘)=48.0sin⁡(0.100∘)=48.0×0.0017453≈0.0838 N⋅m\tau(0.100^\circ) = 48.0\sin(0.100^\circ) = 48.0 \times 0.0017453 \approx 0.0838\text{ N}\cdot\text{m}

Final answer

τ(1.00∘)=0.838 N⋅m\tau(1.00^\circ) = 0.838\text{ N}\cdot\text{m}, τ(0.100∘)=0.0838 N⋅m\tau(0.100^\circ) = 0.0838\text{ N}\cdot\text{m}, lim⁡ϕ→0dτdϕ=48.0 N⋅m/rad\lim_{\phi \to 0}\frac{d\tau}{d\phi} = 48.0\text{ N}\cdot\text{m/rad}

NEXT STEPS
Final Takeaways from Your Teacher
  • Check your calculator display for the 'DEG' indicator whenever you evaluate an angle given in degrees.

  • Use the small-angle approximation sin⁡(ϕ∘)≈ϕ⋅π180\sin(\phi^\circ) \approx \phi \cdot \frac{\pi}{180} as a mental check for angles near 0∘0^\circ.

OverviewACEpath Teacher's Diagnosis

03 The student treats the derivative angle variable as being in degrees rather than radians, introducing a degree-to-radian conversion factor of π/180 into the derivative.

Sample Student Work

Reviewed by ACEpath Teacher
Step-by-Step Review
Walk Through It with Your Teacher
Partially correct
  1. Step 1

    τ(ϕ)=rF0sin⁡ϕ=(0.400)(120)sin⁡ϕ  ⟹  =48.0sin⁡ϕ N⋅m\tau(\phi) = r F_0 \sin\phi = (0.400)(120) \sin\phi \implies = 48.0 \sin\phi \text{ N}\cdot\text{m}

  2. Step 2

    τ(1.00∘)=48.0sin⁡(1.00∘)=0.838 N⋅m  ⟹  τ(0.100∘)=48.0sin⁡(0.100∘)=0.0838 N⋅m\tau(1.00^\circ) = 48.0 \sin(1.00^\circ) = 0.838 \text{ N}\cdot\text{m} \implies \tau(0.100^\circ) = 48.0 \sin(0.100^\circ) = 0.0838 \text{ N}\cdot\text{m}

  3. Step 3

    dτdϕ=48.0(π180)cos⁡ϕ\frac{d\tau}{d\phi} = 48.0 \left(\frac{\pi}{180}\right) \cos\phi

    Correct

    dτdϕ=ddϕ(48.0sin⁡ϕ)=48.0cos⁡ϕ N⋅m/rad\frac{d\tau}{d\phi} = \frac{d}{d\phi}(48.0 \sin\phi) = 48.0 \cos\phi \text{ N}\cdot\text{m/rad}

    In standard calculus, differentiating with respect to an angle variable already assumes the angle is in radians, where ddϕ(sin⁡ϕ)=cos⁡ϕ\frac{d}{d\phi}(\sin\phi) = \cos\phi. Multiplying by π180\frac{\pi}{180} would give the derivative with respect to an angle measured in degrees (N⋅m/deg\text{N}\cdot\text{m/deg}), not radians.

  4. Step 4

    lim⁡ϕ→0dτdϕ=48.0(π180)cos⁡(0)=0.838 N⋅m/rad\lim_{\phi \to 0} \frac{d\tau}{d\phi} = 48.0 \left(\frac{\pi}{180}\right) \cos(0) = 0.838 \text{ N}\cdot\text{m/rad}

    Correct

    lim⁡ϕ→0dτdϕ=48.0cos⁡(0)=48.0 N⋅m/rad\lim_{\phi \to 0} \frac{d\tau}{d\phi} = 48.0 \cos(0) = 48.0 \text{ N}\cdot\text{m/rad}

    You correctly evaluated the limit of your expression as ϕ→0\phi \to 0, but the numerical value was affected by the extra factor introduced in the previous step.

WHAT YOU DID WELL
Compliments from Your Teacher

You stated the correct torque formula as a function of the angle.

You accurately evaluated the trigonometric values at small degree angles.

You recognized that evaluating the limit as ϕ→0\phi \to 0 involves setting cos⁡(0)=1\cos(0) = 1.

THE ERROR
Where Your ACEpath Teacher Spotted the Mistake
Unnecessary degree-to-radian conversion in calculus differentiation

no

WHY IT HAPPENED
ACEpath Teacher's Diagnosis

You treated the angle variable ϕ\phi in the derivative as though it required a conversion from degrees to radians, overlooking that the standard derivative rule ddϕ(sin⁡ϕ)=cos⁡ϕ\frac{d}{d\phi}(\sin\phi) = \cos\phi naturally yields units of per radian.

REASONING PATH
Your ACEpath teacher’s suggested approach
Natural Angle Unit of Calculus
  • The derivative identity ddθ(sin⁡θ)=cos⁡θ\frac{d}{d\theta}(\sin\theta) = \cos\theta is derived using lim⁡θ→0sin⁡θθ=1\lim_{\theta \to 0} \frac{\sin\theta}{\theta} = 1, which is valid only when θ\theta is in radians.

  • Differentiate trigonometric functions directly without inserting conversion factors when the desired derivative unit is per radian.

Derivative Units Check
  • The derivative dydx\frac{dy}{dx} has units of (units of y)/(units of x)(\text{units of } y)/(\text{units of } x).

  • Notice that if you multiply by π180\frac{\pi}{180}, you obtain the derivative with respect to degrees (N⋅m/deg\text{N}\cdot\text{m/deg}), whereas the requested unit is N⋅m/rad\text{N}\cdot\text{m/rad}.

CORRECTED PATH
ACEpath Teacher's Demonstration
  1. Differentiate τ(ϕ)=48.0sin⁡ϕ\tau(\phi) = 48.0 \sin\phi directly with respect to ϕ\phi in radians: dτdϕ=48.0cos⁡ϕ N⋅m/rad\frac{d\tau}{d\phi} = 48.0 \cos\phi \text{ N}\cdot\text{m/rad}.

  2. Evaluate the limit as ϕ→0\phi \to 0: lim⁡ϕ→0dτdϕ=48.0cos⁡(0)=48.0(1)=48.0 N⋅m/rad\lim_{\phi \to 0} \frac{d\tau}{d\phi} = 48.0 \cos(0) = 48.0(1) = 48.0 \text{ N}\cdot\text{m/rad}.

Final answer

τ(1.00∘)=0.838 N⋅m\tau(1.00^\circ) = 0.838\text{ N}\cdot\text{m}, τ(0.100∘)=0.0838 N⋅m\tau(0.100^\circ) = 0.0838\text{ N}\cdot\text{m}, lim⁡ϕ→0dτdϕ=48.0 N⋅m/rad\lim_{\phi \to 0}\frac{d\tau}{d\phi} = 48.0\text{ N}\cdot\text{m/rad}

NEXT STEPS
Final Takeaways from Your Teacher
  • Review why the geometric limit lim⁡x→0sin⁡xx=1\lim_{x \to 0} \frac{\sin x}{x} = 1 requires radians.

  • Practice checking the denominator units of derivatives to ensure proper angular units.

Lock it in

Similar question

01

A mechanic pushes on the end of a 0.250 m0.250\text{ m} long wrench with a force of 80.0 N80.0\text{ N} at an angle of 30.0∘30.0^\circ relative to the handle. Calculate the magnitude of the torque applied to the bolt.

Answer

Using τ=rFsin⁡ϕ\tau = r F \sin\phi: τ=(0.250 m)(80.0 N)sin⁡(30.0∘)=20.0×0.500=10.0 N⋅m\tau = (0.250\text{ m})(80.0\text{ N})\sin(30.0^\circ) = 20.0 \times 0.500 = 10.0\text{ N}\cdot\text{m}

02

A uniform door of width w=0.900 mw = 0.900\text{ m} is pushed at its outer edge with a constant force of F=50.0 NF = 50.0\text{ N} at an angle θ\theta to the door's surface. Find dτdθ\frac{d\tau}{d\theta} at θ=60.0∘\theta = 60.0^\circ in units of N⋅m/rad\text{N}\cdot\text{m/rad}.

Answer

The torque function is τ(θ)=wFsin⁡θ=(0.900)(50.0)sin⁡θ=45.0sin⁡θ N⋅m\tau(\theta) = w F \sin\theta = (0.900)(50.0)\sin\theta = 45.0\sin\theta\text{ N}\cdot\text{m}. Differentiating with respect to θ\theta: dτdθ=45.0cos⁡θ N⋅m/rad\frac{d\tau}{d\theta} = 45.0\cos\theta\text{ N}\cdot\text{m/rad} Evaluating at θ=60.0∘\theta = 60.0^\circ: dτdθ=45.0cos⁡(60.0∘)=45.0×0.500=22.5 N⋅m/rad\frac{d\tau}{d\theta} = 45.0\cos(60.0^\circ) = 45.0 \times 0.500 = 22.5\text{ N}\cdot\text{m/rad}

03

A lever arm of length L=1.20 mL = 1.20\text{ m} rotates about a fixed pivot. A force F=150 NF = 150\text{ N} acts at its tip at a small angle ϕ\phi from the lever axis. Using the small-angle approximation sin⁡ϕ≈ϕ\sin\phi \approx \phi (with ϕ\phi in radians), estimate the torque produced when ϕ=2.00∘\phi = 2.00^\circ.

Answer

Convert the angle to radians: ϕ=2.00∘×π180∘=π90≈0.03491 rad\phi = 2.00^\circ \times \frac{\pi}{180^\circ} = \frac{\pi}{90} \approx 0.03491\text{ rad} Using the small-angle approximation: τ≈LFϕ=(1.20 m)(150 N)(0.03491 rad)≈6.28 N⋅m\tau \approx L F \phi = (1.20\text{ m})(150\text{ N})(0.03491\text{ rad}) \approx 6.28\text{ N}\cdot\text{m}

Loading workspace…