Resources

A hydraulic lift system filled with an incompressible liquid of density ρ=920 kg/m3\rho = 920\text{ kg/m}^3 has an input cylinder of cross-sectional area A1=15.0 cm2A_1 = 15.0\text{ cm}^2 and an output cylinder of cross-sectional area A2=450 cm2A_2 = 450\text{ cm}^2. An operator pushes the input piston downward by applying an external force F1=300 NF_1 = 300\text{ N}. However, due to system geometry, the input piston is situated at a vertical height of h=2.20 mh = 2.20\text{ m} above the output piston surface. Adhering strictly to fluid statics and hydrostatic pressure variation (P2=P1+ρghP_2 = P_1 + \rho g h), calculate the total upward force F2F_2 exerted by the fluid on the output piston (take g=9.80 m/s2g = 9.80\text{ m/s}^2).

Answer and steps

Final answer

F2=9890 NF_2 = 9890\text{ N}

Steps

01

Convert units to standard SI units

First, express the cross-sectional areas of both pistons in square meters (m2\text{m}^2):

A1=15.0 cm2=15.0×10−4 m2=0.00150 m2A_1 = 15.0\text{ cm}^2 = 15.0 \times 10^{-4}\text{ m}^2 = 0.00150\text{ m}^2

A2=450 cm2=450×10−4 m2=0.0450 m2A_2 = 450\text{ cm}^2 = 450 \times 10^{-4}\text{ m}^2 = 0.0450\text{ m}^2


02

Determine the pressure applied at the input piston (P1P_1)

The external downward force F1F_1 exerted on the smaller area A1A_1 creates an additional pressure in the fluid at the input surface:

P1=F1A1=300 N0.00150 m2=2.00×105 PaP_1 = \frac{F_1}{A_1} = \frac{300\text{ N}}{0.00150\text{ m}^2} = 2.00 \times 10^5\text{ Pa}


03

Account for hydrostatic pressure variation with depth

According to fluid statics, pressure increases with depth in a continuous column of static fluid. Because the input piston is located at a vertical distance h=2.20 mh = 2.20\text{ m} above the output piston, the fluid at the output piston is under the combined effect of the applied pressure and the weight of the fluid column of height hh:

P2=P1+ρghP_2 = P_1 + \rho g h

Calculate the hydrostatic contribution:

ρgh=(920 kg/m3)(9.80 m/s2)(2.20 m)=19,835.2 Pa\rho g h = (920\text{ kg/m}^3)(9.80\text{ m/s}^2)(2.20\text{ m}) = 19{,}835.2\text{ Pa}

Thus, the total pressure at the level of the output piston is:

P2=200,000 Pa+19,835.2 Pa=219,835.2 PaP_2 = 200{,}000\text{ Pa} + 19{,}835.2\text{ Pa} = 219{,}835.2\text{ Pa}

Common Pitfall: In ideal hydraulic lifts where both pistons are at the exact same elevation (h=0h = 0), pressure is transmitted equally (P1=P2P_1 = P_2). When there is an elevation difference, neglecting the hydrostatic term ρgh\rho g h leads to an underestimated force at the lower piston.


04

Calculate the total upward force on the output piston (F2F_2)

The upward force exerted by the fluid against the output piston is the product of the total pressure P2P_2 at that depth and the output piston area A2A_2:

F2=P2⋅A2=(219,835.2 Pa)(0.0450 m2)≈9892.6 NF_2 = P_2 \cdot A_2 = (219{,}835.2\text{ Pa})(0.0450\text{ m}^2) \approx 9892.6\text{ N}

Rounding to three significant figures gives:

F2=9890 NF_2 = 9890\text{ N}

Typical errors

OverviewACEpath Teacher's Diagnosis

01 The student ignores the hydrostatic height difference ρgh and assumes standard ideal Pascal's principle (P1 = P2), resulting in an underestimated output force.

Sample Student Work

Reviewed by ACEpath Teacher
Step-by-Step Review
Walk Through It with Your Teacher
Incorrect
  1. Step 1

    P1=F1A1  ⟹  A1=15.0 cm2=0.0015 m2  ⟹  P1=3000.0015=200000 PaP_1 = \frac{F_1}{A_1} \implies A_1 = 15.0\text{ cm}^2 = 0.0015\text{ m}^2 \implies P_1 = \frac{300}{0.0015} = 200000\text{ Pa}

  2. Step 2

    P2=P1=200000 PaP_2 = P_1 = 200000\text{ Pa}

    Correct

    P2=P1+ρgh=200000 Pa+(920 kg/m3)(9.80 m/s2)(2.20 m)=219835.2 PaP_2 = P_1 + \rho g h = 200000\text{ Pa} + (920\text{ kg/m}^3)(9.80\text{ m/s}^2)(2.20\text{ m}) = 219835.2\text{ Pa}

    Because the input piston is situated 2.20 m2.20\text{ m} above the output piston, fluid statics requires adding the hydrostatic column pressure ρgh\rho g h to find P2P_2.

  3. Step 3

    A2=450 cm2=0.045 m2  ⟹  F2=P2×A2=200000×0.045=9000 NA_2 = 450\text{ cm}^2 = 0.045\text{ m}^2 \implies F_2 = P_2 \times A_2 = 200000 \times 0.045 = 9000\text{ N}

    Correct

    F2=P2A2=(219835.2 Pa)(0.0450 m2)≈9890 NF_2 = P_2 A_2 = (219835.2\text{ Pa})(0.0450\text{ m}^2) \approx 9890\text{ N}

    Your area conversion and multiplication were executed correctly, but the result is too low due to the missing hydrostatic term in P2P_2.

WHAT YOU DID WELL
Compliments from Your Teacher

You accurately converted square centimeters to square meters for both piston areas.

You correctly used the definition of pressure P=FAP = \frac{F}{A} to find P1P_1.

THE ERROR
Where Your ACEpath Teacher Spotted the Mistake
Neglected hydrostatic height difference

no

WHY IT HAPPENED
ACEpath Teacher's Diagnosis

You defaulted to standard ideal Pascal's principle (P1=P2P_1 = P_2), which only holds when both pistons share the same horizontal level, ignoring the downward hydrostatic pressure increase ρgh\rho g h from the fluid column.

REASONING PATH
Your ACEpath teacher’s suggested approach
Evaluate piston heights
  • If two pistons in a static continuous fluid are separated by vertical height hh, pressure increases with depth: Plower=Pupper+ρghP_{\text{lower}} = P_{\text{upper}} + \rho g h.

  • Always compare the vertical levels of the two surfaces before equating their pressures.

CORRECTED PATH
ACEpath Teacher's Demonstration
  1. Compute the hydrostatic term: ρgh=(920 kg/m3)(9.80 m/s2)(2.20 m)=19835.2 Pa\rho g h = (920\text{ kg/m}^3)(9.80\text{ m/s}^2)(2.20\text{ m}) = 19835.2\text{ Pa}.

  2. Find total pressure at the output piston: P2=P1+ρgh=200000 Pa+19835.2 Pa=219835.2 PaP_2 = P_1 + \rho g h = 200000\text{ Pa} + 19835.2\text{ Pa} = 219835.2\text{ Pa}.

  3. Calculate upward output force: F2=P2A2=(219835.2 Pa)(0.0450 m2)≈9890 NF_2 = P_2 A_2 = (219835.2\text{ Pa})(0.0450\text{ m}^2) \approx 9890\text{ N}.

Final answer

F2=9890 NF_2 = 9890\text{ N}

NEXT STEPS
Final Takeaways from Your Teacher
  • Review the hydrostatic equation P=P0+ρghP = P_0 + \rho g h for connected fluid columns.

  • Identify whether pistons sit at equal or unequal elevations before setting up the pressure equation.

  • Practice problems where fluid columns either add to or oppose the applied piston pressure.

OverviewACEpath Teacher's Diagnosis

02 The student subtracts the hydrostatic head instead of adding it, incorrectly writing P2 = P1 - ρgh under the misconception that being below reduces pressure.

Sample Student Work

Reviewed by ACEpath Teacher
Step-by-Step Review
Walk Through It with Your Teacher
Incorrect
  1. Step 1

    A1=15.0×10−4 m2,  A2=450×10−4 m2=0.045 m2A_1 = 15.0 \times 10^{-4}\text{ m}^2,\; A_2 = 450 \times 10^{-4}\text{ m}^2 = 0.045\text{ m}^2

  2. Step 2

    P1=3000.0015=200000 PaP_1 = \frac{300}{0.0015} = 200000\text{ Pa}

  3. Step 3

    ρgh=920×9.80×2.20=19835.2 Pa\rho g h = 920 \times 9.80 \times 2.20 = 19835.2\text{ Pa}

  4. Step 4

    P2=P1−ρgh=200000−19835.2=180164.8 PaP_2 = P_1 - \rho g h = 200000 - 19835.2 = 180164.8\text{ Pa}

    Correct

    P2=P1+ρgh=200000 Pa+19835.2 Pa=219835.2 PaP_2 = P_1 + \rho g h = 200000\text{ Pa} + 19835.2\text{ Pa} = 219835.2\text{ Pa}

    You subtracted the fluid column pressure rather than adding it. Because the output piston is located a distance hh below the input piston, the weight of the fluid column increases the pressure at the bottom: P2=P1+ρghP_2 = P_1 + \rho g h.

  5. Step 5

    F2=P2×A2=180164.8×0.045=8107.4 NF_2 = P_2 \times A_2 = 180164.8 \times 0.045 = 8107.4\text{ N}

    Correct

    F2=P2⋅A2=(219835.2 Pa)(0.0450 m2)≈9890 NF_2 = P_2 \cdot A_2 = (219835.2\text{ Pa})(0.0450\text{ m}^2) \approx 9890\text{ N}

    You correctly multiplied pressure by output area, but the result is affected by the incorrect value of P2P_2 from the previous step.

WHAT YOU DID WELL
Compliments from Your Teacher

You correctly converted the cross-sectional areas from square centimeters to square meters.

You accurately calculated the applied pressure at the input piston.

You correctly evaluated the product ρgh\rho g h for the hydrostatic pressure head.

You applied the relation F2=P2A2F_2 = P_2 A_2 correctly to determine the output force.

THE ERROR
Where Your ACEpath Teacher Spotted the Mistake
Sign error in hydrostatic pressure variation

no

WHY IT HAPPENED
ACEpath Teacher's Diagnosis

You subtracted the hydrostatic pressure term ρgh\rho g h instead of adding it, confusing the sign convention for depth. In static fluids, moving downward into the fluid adds the weight of the overlying fluid column, which increases pressure (Plower=Pupper+ρghP_{\text{lower}} = P_{\text{upper}} + \rho g h).

REASONING PATH
Your ACEpath teacher’s suggested approach
Pressure vs. Depth Rule
  • Pressure increases as you move downward in a continuous fluid column: Pbottom=Ptop+ρghP_{\text{bottom}} = P_{\text{top}} + \rho g h.

  • Before writing your equation, ask yourself whether the target point is deeper or shallower than your reference point. Deeper points always have higher pressure.

CORRECTED PATH
ACEpath Teacher's Demonstration
  1. P2=200000 Pa+19835.2 Pa=219835.2 PaP_2 = 200000\text{ Pa} + 19835.2\text{ Pa} = 219835.2\text{ Pa}

  2. F2=P2⋅A2=(219835.2 Pa)(0.0450 m2)=9892.584 N≈9890 NF_2 = P_2 \cdot A_2 = (219835.2\text{ Pa})(0.0450\text{ m}^2) = 9892.584\text{ N} \approx 9890\text{ N}

Final answer

F2=9890 NF_2 = 9890\text{ N}

NEXT STEPS
Final Takeaways from Your Teacher
  • Remember the mnemonic 'deeper means denser weight above, so add ρgh\rho g h'.

  • Practice drawing a quick vertical depth line to visually check which point has a larger fluid column resting above it.

OverviewACEpath Teacher's Diagnosis

03 The student converts cm² to m² incorrectly using a factor of 10⁻² instead of 10⁻⁴, causing the pressure and force to be off by orders of magnitude.

Sample Student Work

Reviewed by ACEpath Teacher
Step-by-Step Review
Walk Through It with Your Teacher
Incorrect
  1. Step 1

    A1=15.0×10−2 m2=0.15 m2  ⟹  A2=450×10−2 m2=4.5 m2A_1 = 15.0 \times 10^{-2}\text{ m}^2 = 0.15\text{ m}^2 \implies A_2 = 450 \times 10^{-2}\text{ m}^2 = 4.5\text{ m}^2

    Correct

    A1=15.0 cm2×(10−2 m/cm)2=1.50×10−3 m2  ⟹  A2=450 cm2×(10−2 m/cm)2=0.0450 m2A_1 = 15.0\text{ cm}^2 \times (10^{-2}\text{ m}/\text{cm})^2 = 1.50 \times 10^{-3}\text{ m}^2 \implies A_2 = 450\text{ cm}^2 \times (10^{-2}\text{ m}/\text{cm})^2 = 0.0450\text{ m}^2

    You converted from cm2\text{cm}^2 to m2\text{m}^2 by multiplying by 10−210^{-2} instead of (10−2)2=10−4(10^{-2})^2 = 10^{-4}. Because 1 m=100 cm1\text{ m} = 100\text{ cm}, one square meter equals (100 cm)2=10,000 cm2(100\text{ cm})^2 = 10{,}000\text{ cm}^2, so 1 cm2=10−4 m21\text{ cm}^2 = 10^{-4}\text{ m}^2.

  2. Step 2

    P1=3000.15=2000 PaP_1 = \frac{300}{0.15} = 2000\text{ Pa}

    Correct

    P1=F1A1=300 N0.00150 m2=2.00×105 PaP_1 = \frac{F_1}{A_1} = \frac{300\text{ N}}{0.00150\text{ m}^2} = 2.00 \times 10^5\text{ Pa}

    You used the correct pressure formula P1=F1A1P_1 = \frac{F_1}{A_1}, but substituting the incorrect area A1=0.15 m2A_1 = 0.15\text{ m}^2 produced 2000 Pa2000\text{ Pa} instead of 2.00×105 Pa2.00 \times 10^5\text{ Pa}.

  3. Step 3

    ρgh=920×9.80×2.20=19835.2 Pa\rho g h = 920 \times 9.80 \times 2.20 = 19835.2\text{ Pa}

  4. Step 4

    P2=P1+ρgh=2000+19835.2=21835.2 PaP_2 = P_1 + \rho g h = 2000 + 19835.2 = 21835.2\text{ Pa}

    Correct

    P2=200,000 Pa+19,835.2 Pa=219,835.2 PaP_2 = 200{,}000\text{ Pa} + 19{,}835.2\text{ Pa} = 219{,}835.2\text{ Pa}

    You correctly added the hydrostatic contribution to the input pressure, but the value is lower than expected due to the earlier area conversion error.

  5. Step 5

    F2=P2×A2=21835.2×4.5=98258.4 NF_2 = P_2 \times A_2 = 21835.2 \times 4.5 = 98258.4\text{ N}

    Correct

    F2=P2×A2=(219,835.2 Pa)(0.0450 m2)≈9890 NF_2 = P_2 \times A_2 = (219{,}835.2\text{ Pa})(0.0450\text{ m}^2) \approx 9890\text{ N}

    Your formula F2=P2⋅A2F_2 = P_2 \cdot A_2 and arithmetic were correct, but substituting the incorrect values for P2P_2 and A2A_2 led to an incorrect final upward force.

WHAT YOU DID WELL
Compliments from Your Teacher

You correctly identified and applied the hydrostatic pressure variation formula P2=P1+ρghP_2 = P_1 + \rho g h.

You correctly evaluated the hydrostatic term ρgh\rho g h using the given density, gravity, and elevation difference.

You used the correct fundamental definitions of pressure and force (P=FAP = \frac{F}{A} and F=P⋅AF = P \cdot A).

THE ERROR
Where Your ACEpath Teacher Spotted the Mistake
Unit Conversion Error (Area)

You treated the area conversion from cm2\text{cm}^2 to m2\text{m}^2 as a linear length conversion, multiplying by 10−210^{-2} instead of 10−410^{-4}.

WHY IT HAPPENED
ACEpath Teacher's Diagnosis

Confusing linear dimension conversion factors with two-dimensional (area) conversion factors where the linear scale factor must be squared.

REASONING PATH
Your ACEpath teacher’s suggested approach
Square the conversion factor for area
  • Because 1 m=100 cm=102 cm1\text{ m} = 100\text{ cm} = 10^2\text{ cm}, squaring both sides yields 1 m2=(102 cm)2=104 cm21\text{ m}^2 = (10^2\text{ cm})^2 = 10^4\text{ cm}^2, which means 1 cm2=10−4 m21\text{ cm}^2 = 10^{-4}\text{ m}^2.

  • Always write out (10−2 m/1 cm)2(10^{-2}\text{ m}/1\text{ cm})^2 explicitly when converting square centimeters to square meters.

CORRECTED PATH
ACEpath Teacher's Demonstration
  1. Convert areas accurately: A1=15.0×10−4 m2=0.00150 m2A_1 = 15.0 \times 10^{-4}\text{ m}^2 = 0.00150\text{ m}^2 and A2=450×10−4 m2=0.0450 m2A_2 = 450 \times 10^{-4}\text{ m}^2 = 0.0450\text{ m}^2.

  2. Recalculate input pressure: P1=300 N0.00150 m2=2.00×105 PaP_1 = \frac{300\text{ N}}{0.00150\text{ m}^2} = 2.00 \times 10^5\text{ Pa}.

  3. Add the hydrostatic head: P2=P1+ρgh=200,000 Pa+19,835.2 Pa=219,835.2 PaP_2 = P_1 + \rho g h = 200{,}000\text{ Pa} + 19{,}835.2\text{ Pa} = 219{,}835.2\text{ Pa}.

  4. Compute output force: F2=P2×A2=(219,835.2 Pa)(0.0450 m2)≈9892.6 NF_2 = P_2 \times A_2 = (219{,}835.2\text{ Pa})(0.0450\text{ m}^2) \approx 9892.6\text{ N}.

Final answer

F2=9890 NF_2 = 9890\text{ N} (to three significant figures)

NEXT STEPS
Final Takeaways from Your Teacher
  • Review unit conversions involving powers (area cm2→m2\text{cm}^2 \to \text{m}^2 and volume cm3→m3\text{cm}^3 \to \text{m}^3).

  • Practice checking whether calculated areas are physically reasonable: a piston of 4.5 m24.5\text{ m}^2 would have a radius over 1 meter1\text{ meter}, which is unusually large for typical hydraulic lab problems.

  • Work through the flashcards and practice problems below to master two-dimensional unit scaling in fluid mechanics.

Lock it in

Similar question

01

A hydraulic press filled with oil (ρ=850 kg/m3\rho = 850\text{ kg/m}^3) has an input piston of area A1=0.010 m2A_1 = 0.010\text{ m}^2 and an output piston of area A2=0.20 m2A_2 = 0.20\text{ m}^2. The input piston is pushed down with F1=250 NF_1 = 250\text{ N} and sits 1.50 m1.50\text{ m} above the output piston. Taking g=9.80 m/s2g = 9.80\text{ m/s}^2, find the total force F2F_2 on the output piston.

Answer

F2=7500 NF_2 = 7500\text{ N}.

  1. P1=2500.010=25000 PaP_1 = \frac{250}{0.010} = 25000\text{ Pa}.
  2. P2=P1+ρgh=25000+(850)(9.80)(1.50)=25000+12495=37495 PaP_2 = P_1 + \rho g h = 25000 + (850)(9.80)(1.50) = 25000 + 12495 = 37495\text{ Pa}.
  3. F2=P2A2=37495×0.20=7499 N≈7500 NF_2 = P_2 A_2 = 37495 \times 0.20 = 7499\text{ N} \approx 7500\text{ N}.
02

In a hydraulic lift (fluid density ρ=1000 kg/m3\rho = 1000\text{ kg/m}^3, g=9.80 m/s2g = 9.80\text{ m/s}^2), the output piston with area A2=0.50 m2A_2 = 0.50\text{ m}^2 is situated 3.00 m3.00\text{ m} HIGHER than the input piston (A1=0.020 m2A_1 = 0.020\text{ m}^2). If an upward force of F2=12000 NF_2 = 12000\text{ N} must be supported at the output piston, what minimum downward force F1F_1 must be applied at the input piston?

Answer

F1=1070 NF_1 = 1070\text{ N}.

  1. Output pressure: P2=F2A2=120000.50=24000 PaP_2 = \frac{F_2}{A_2} = \frac{12000}{0.50} = 24000\text{ Pa}.
  2. Since input is deeper by h=3.00 mh = 3.00\text{ m}: P1=P2+ρgh=24000+(1000)(9.80)(3.00)=53400 PaP_1 = P_2 + \rho g h = 24000 + (1000)(9.80)(3.00) = 53400\text{ Pa}.
  3. F1=P1A1=53400×0.020=1068 N≈1070 NF_1 = P_1 A_1 = 53400 \times 0.020 = 1068\text{ N} \approx 1070\text{ N}.
03

A U-tube hydraulic system with liquid density ρ\rho has two pistons. Left piston has area AA and applied force FF; right piston has area 3A3A and sits at distance hh below the left piston. Derive a symbolic expression for the total upward force FRF_R on the right piston.

Answer

FR=3F+3ρghAF_R = 3F + 3\rho g h A.

  1. Pressure at left piston: PL=FAP_L = \frac{F}{A}.
  2. Pressure at right piston: PR=PL+ρgh=FA+ρghP_R = P_L + \rho g h = \frac{F}{A} + \rho g h.
  3. Upward force: FR=PR(3A)=(FA+ρgh)(3A)=3F+3ρghAF_R = P_R (3A) = \left(\frac{F}{A} + \rho g h\right)(3A) = 3F + 3\rho g h A.
Loading workspace…