Resources

A cylindrical hot water storage pipe of radius r1=10.0 mmr_1 = 10.0\text{ mm} carries hot water at Ti=80.0∘CT_i = 80.0^{\circ}\text{C} through an open basement at T∞=20.0∘CT_{\infty} = 20.0^{\circ}\text{C}. The external natural convection coefficient is h=10.0 W/(m2⋅K)h = 10.0\text{ W}/(\text{m}^2\cdot\text{K}). An insulation contractor suggests adding a sleeve of flexible fiberglass insulation with thermal conductivity k=0.0400 W/(m⋅K)k = 0.0400\text{ W}/(\text{m}\cdot\text{K}) of outer radius r2=12.0 mmr_2 = 12.0\text{ mm} (2.00 mm2.00\text{ mm} insulation thickness). (a) Calculate the critical radius of insulation rcrr_{\text{cr}} for this cylinder. (b) Determine the rate of heat loss per unit length Q˙′\dot{Q}' of the bare pipe (r1=10.0 mmr_1 = 10.0\text{ mm}) versus the insulated pipe (r2=12.0 mmr_2 = 12.0\text{ mm}), and evaluate whether adding this thin insulation increases or decreases the rate of heat loss.

Answer and steps

Final answer

(a) rcr=4.00×10−3 m=4.00 mmr_{\text{cr}} = 4.00\times 10^{-3}\text{ m} = 4.00\text{ mm}; (b) Bare pipe: Q˙bare′=37.7 W/m\dot{Q}'_{\text{bare}} = 37.7\text{ W}/\text{m}; Insulated pipe: Q˙ins′=32.4 W/m\dot{Q}'_{\text{ins}} = 32.4\text{ W}/\text{m}. Adding this insulation decreases the heat loss rate by 14.1%14.1\% because the outer radius r1=10.0 mmr_1 = 10.0\text{ mm} is already greater than rcrr_{\text{cr}}.

Steps

01

Bare Pipe (r1=10.0 mm=0.0100 mr_1 = 10.0\text{ mm} = 0.0100\text{ m})

Part (a): Critical Radius of Insulation

For a cylindrical geometry, adding insulation introduces two competing effects:

  1. Conduction resistance increases logarithmically with outer radius r2r_2.
  2. Convection resistance decreases inversely with r2r_2 because the external surface area increases. The critical radius of insulation rcrr_{\text{cr}} represents the outer radius at which total thermal resistance is minimized (and heat transfer is maximized). It is defined as: rcr=khr_{\text{cr}} = \frac{k}{h} Substitute the given values:
  • Thermal conductivity of insulation: k=0.0400 W/(m⋅K)k = 0.0400\text{ W}/(\text{m}\cdot\text{K})
  • Convection heat transfer coefficient: h=10.0 W/(m2⋅K)h = 10.0\text{ W}/(\text{m}^2\cdot\text{K}) rcr=0.0400 W/(m⋅K)10.0 W/(m2⋅K)=0.00400 m=4.00 mmr_{\text{cr}} = \frac{0.0400\text{ W}/(\text{m}\cdot\text{K})}{10.0\text{ W}/(\text{m}^2\cdot\text{K})} = 0.00400\text{ m} = 4.00\text{ mm}

Part (b): Heat Loss Rates

Let LL be the length of the pipe. We calculate the heat transfer rate per unit length, Q˙′=Q˙/L\dot{Q}' = \dot{Q}/L.

The bare pipe surface is maintained at Ti=80.0∘CT_i = 80.0^{\circ}\text{C} and loses heat solely through external convection to the surrounding air at T∞=20.0∘CT_{\infty} = 20.0^{\circ}\text{C}.

The surface area per unit length is A′/L=2πr1A'/L = 2\pi r_1. Using Newton's law of cooling:

Q˙bare′=h(2πr1)(Ti−T∞)\dot{Q}'_{\text{bare}} = h(2\pi r_1)(T_i - T_{\infty})

Q˙bare′=(10.0 W/(m2⋅K))⋅(2π⋅0.0100 m)⋅(80.0∘C−20.0∘C)\dot{Q}'_{\text{bare}} = (10.0\text{ W}/(\text{m}^2\cdot\text{K})) \cdot (2\pi \cdot 0.0100\text{ m}) \cdot (80.0^{\circ}\text{C} - 20.0^{\circ}\text{C})

Q˙bare′=20.0π⋅0.0100⋅60.0≈37.7 W/m\dot{Q}'_{\text{bare}} = 20.0\pi \cdot 0.0100 \cdot 60.0 \approx 37.7\text{ W}/\text{m}

02

Insulated Pipe (r1=0.0100 mr_1 = 0.0100\text{ m}, r2=0.0120 mr_2 = 0.0120\text{ m})

For the insulated cylinder, heat flows in series through:

  1. Conduction through the cylindrical insulation layer: Rcond′=ln⁡(r2/r1)2πkR'_{\text{cond}} = \frac{\ln(r_2/r_1)}{2\pi k}
  2. Convection from the outer surface to ambient air: Rconv′=12πr2hR'_{\text{conv}} = \frac{1}{2\pi r_2 h}

The total thermal resistance per unit length is:

Rtotal′=Rcond′+Rconv′=ln⁡(r2/r1)2πk+12πr2hR'_{\text{total}} = R'_{\text{cond}} + R'_{\text{conv}} = \frac{\ln(r_2/r_1)}{2\pi k} + \frac{1}{2\pi r_2 h}

Calculate each resistance component: Rcond′=ln⁡(0.0120/0.0100)2π⋅0.0400=ln⁡(1.2)0.0800π≈0.182320.25133≈0.7254 m⋅K/WR'_{\text{cond}} = \frac{\ln(0.0120 / 0.0100)}{2\pi \cdot 0.0400} = \frac{\ln(1.2)}{0.0800\pi} \approx \frac{0.18232}{0.25133} \approx 0.7254\text{ m}\cdot\text{K}/\text{W}

Rconv′=12π⋅0.0120⋅10.0=10.240π≈1.3263 m⋅K/WR'_{\text{conv}} = \frac{1}{2\pi \cdot 0.0120 \cdot 10.0} = \frac{1}{0.240\pi} \approx 1.3263\text{ m}\cdot\text{K}/\text{W}

Rtotal′=0.7254+1.3263=2.0517 m⋅K/WR'_{\text{total}} = 0.7254 + 1.3263 = 2.0517\text{ m}\cdot\text{K}/\text{W}

The rate of heat loss per unit length is:

Q˙ins′=Ti−T∞Rtotal′=80.0−20.02.0517≈32.4 W/m\dot{Q}'_{\text{ins}} = \frac{T_i - T_{\infty}}{R'_{\text{total}}} = \frac{80.0 - 20.0}{2.0517} \approx 32.4\text{ W}/\text{m}

03

Evaluation

Comparing the two rates:

  • Q˙bare′=37.7 W/m\dot{Q}'_{\text{bare}} = 37.7\text{ W}/\text{m}
  • Q˙ins′=32.4 W/m\dot{Q}'_{\text{ins}} = 32.4\text{ W}/\text{m}

The percentage reduction in heat loss is:

Percentage reduction=37.7−32.437.7×100%≈14.1%\text{Percentage reduction} = \frac{37.7 - 32.4}{37.7} \times 100\% \approx 14.1\%

Adding the insulation decreases heat loss because the bare pipe radius (r1=10.0 mmr_1 = 10.0\text{ mm}) is already larger than the critical radius (rcr=4.00 mmr_{\text{cr}} = 4.00\text{ mm}). For any radius r>rcrr > r_{\text{cr}}, the increase in conductive resistance dominates over the decrease in convective resistance, leading to a net reduction in heat loss.

Typical errors

OverviewACEpath Teacher's Diagnosis

01 The student confuses the critical radius formula for a cylinder with that of a sphere by using r_cr = 2k/h instead of k/h.

Sample Student Work

Reviewed by ACEpath Teacher
Step-by-Step Review
Walk Through It with Your Teacher
Partially correct
  1. Step 1

    rcr=2kh⟹rcr=2(0.0400)10.0=0.00800 m=8.00 mmr_{\text{cr}} = \frac{2k}{h} \Longrightarrow r_{\text{cr}} = \frac{2(0.0400)}{10.0} = 0.00800\text{ m} = 8.00\text{ mm}

    Correct

    rcr=kh=0.040010.0=0.00400 m=4.00 mmr_{\text{cr}} = \frac{k}{h} = \frac{0.0400}{10.0} = 0.00400\text{ m} = 4.00\text{ mm}

    You used the critical radius formula for a sphere, rcr=2khr_{\text{cr}} = \frac{2k}{h}, instead of the formula for a cylinder, rcr=khr_{\text{cr}} = \frac{k}{h}.

  2. Step 2

    Rbare′=12πr1h=12π(0.0100)(10.0)=1.592 m⋅K/W⟹Q˙bare′=80.0−20.01.592=37.7 W/mR'_{\text{bare}} = \frac{1}{2\pi r_1 h} = \frac{1}{2\pi(0.0100)(10.0)} = 1.592\text{ m}\cdot\text{K}/\text{W} \Longrightarrow \dot{Q}'_{\text{bare}} = \frac{80.0 - 20.0}{1.592} = 37.7\text{ W}/\text{m}

  3. Step 3

    Rcond′=ln⁡(12.0/10.0)2π(0.0400)=0.725 m⋅K/W⟹Rconv′=12π(0.0120)(10.0)=1.326 m⋅K/W⟹Rtotal′=0.725+1.326=2.051 m⋅K/W⟹Q˙ins′=60.02.051=29.2 W/mR'_{\text{cond}} = \frac{\ln(12.0/10.0)}{2\pi(0.0400)} = 0.725\text{ m}\cdot\text{K}/\text{W} \Longrightarrow R'_{\text{conv}} = \frac{1}{2\pi(0.0120)(10.0)} = 1.326\text{ m}\cdot\text{K}/\text{W} \Longrightarrow R'_{\text{total}} = 0.725 + 1.326 = 2.051\text{ m}\cdot\text{K}/\text{W} \Longrightarrow \dot{Q}'_{\text{ins}} = \frac{60.0}{2.051} = 29.2\text{ W}/\text{m}

  4. Step 4

    Adding insulation decreases heat loss since 29.2 W/m<37.7 W/m.\text{Adding insulation decreases heat loss since } 29.2\text{ W}/\text{m} < 37.7\text{ W}/\text{m}.

WHAT YOU DID WELL
Compliments from Your Teacher

You correctly set up and computed the thermal resistance network for both the bare and insulated cylindrical pipes.

You accurately determined that adding insulation reduces heat loss by comparing the calculated heat transfer rates.

THE ERROR
Where Your ACEpath Teacher Spotted the Mistake
Geometry Formula Confusion

You wrote rcr=2khr_{\text{cr}} = \frac{2k}{h} instead of rcr=khr_{\text{cr}} = \frac{k}{h}.

WHY IT HAPPENED
ACEpath Teacher's Diagnosis

You confused the critical radius of insulation expression for spherical geometries with the expression for cylindrical geometries.

REASONING PATH
Your ACEpath teacher’s suggested approach
Geometry Distinction for Critical Radius
  • For a cylinder, rcr=khr_{\text{cr}} = \frac{k}{h}. For a sphere, rcr=2khr_{\text{cr}} = \frac{2k}{h}.

  • Check the geometry of the system before selecting the critical radius formula: remember that the factor of 2 arises only from the spherical surface area derivative ddr(4πr2)=8πr\frac{d}{dr}(4\pi r^2) = 8\pi r versus the cylindrical ddr(2πrL)=2πL\frac{d}{dr}(2\pi r L) = 2\pi L.

CORRECTED PATH
ACEpath Teacher's Demonstration
  1. Identify the geometry as a cylinder, for which the total thermal resistance per unit length is R′(r)=ln⁡(r/r1)2πk+12πrhR'(r) = \frac{\ln(r/r_1)}{2\pi k} + \frac{1}{2\pi r h}.

  2. Differentiate with respect to outer radius rr and set to zero: dR′dr=12πkr−12πhr2=0\frac{dR'}{dr} = \frac{1}{2\pi k r} - \frac{1}{2\pi h r^2} = 0.

  3. Solve for rr: rcr=khr_{\text{cr}} = \frac{k}{h}.

  4. Substitute k=0.0400 W/(m⋅K)k = 0.0400\text{ W}/(\text{m}\cdot\text{K}) and h=10.0 W/(m2⋅K)h = 10.0\text{ W}/(\text{m}^2\cdot\text{K}) to obtain rcr=4.00 mmr_{\text{cr}} = 4.00\text{ mm}.

Final answer

(a) rcr=4.00 mmr_{\text{cr}} = 4.00\text{ mm}; (b) Q˙bare′=37.7 W/m\dot{Q}'_{\text{bare}} = 37.7\text{ W}/\text{m}, Q˙ins′≈29.2 W/m\dot{Q}'_{\text{ins}} \approx 29.2\text{ W}/\text{m} (or 32.4 W/m32.4\text{ W}/\text{m} with rounded values); adding insulation decreases heat loss.

NEXT STEPS
Final Takeaways from Your Teacher
  • Review the thermal resistance derivation for cylinders versus spheres to see how the geometric surface area affects the critical radius.

  • Practice distinguishing between cylindrical (k/hk/h) and spherical (2k/h2k/h) critical radius problems.

OverviewACEpath Teacher's Diagnosis

02 The student misapplies the critical radius concept by qualitatively assuming any added insulation below the outer radius r2 will increase heat loss without checking if r1 already exceeds r_cr.

Sample Student Work

Reviewed by ACEpath Teacher
Step-by-Step Review
Walk Through It with Your Teacher
Partially correct
  1. Step 1

    rcr=kh=0.040010.0=0.00400 m=4.00 mmr_{\text{cr}} = \frac{k}{h} = \frac{0.0400}{10.0} = 0.00400\text{ m} = 4.00\text{ mm}

  2. Step 2

    Rbare′=12π⋅0.0100⋅10.0=1.592 m⋅K/W  ⟹  Q˙bare′=60.01.592=37.7 W/mR'_{\text{bare}} = \frac{1}{2\pi \cdot 0.0100 \cdot 10.0} = 1.592\text{ m}\cdot\text{K}/\text{W} \implies \dot{Q}'_{\text{bare}} = \frac{60.0}{1.592} = 37.7\text{ W}/\text{m}

  3. Step 3

    Rcond′=ln⁡(12/10)2π⋅0.0400=0.725 m⋅K/W  ⟹  Rconv′=12π⋅0.0120⋅10.0=1.326 m⋅K/W  ⟹  Rtotal′=2.051 m⋅K/W  ⟹  Q˙ins′=60.02.051=29.2 W/mR'_{\text{cond}} = \frac{\ln(12/10)}{2\pi \cdot 0.0400} = 0.725\text{ m}\cdot\text{K}/\text{W} \implies R'_{\text{conv}} = \frac{1}{2\pi \cdot 0.0120 \cdot 10.0} = 1.326\text{ m}\cdot\text{K}/\text{W} \implies R'_{\text{total}} = 2.051\text{ m}\cdot\text{K}/\text{W} \implies \dot{Q}'_{\text{ins}} = \frac{60.0}{2.051} = 29.2\text{ W}/\text{m}

  4. Step 4

    Because insulation was added to a thin pipe, heat loss increases due to increased surface area.

    Correct

    Because r1=10.0 mm>rcr=4.00 mmr_1 = 10.0\text{ mm} > r_{\text{cr}} = 4.00\text{ mm}, adding insulation increases total thermal resistance, so heat loss decreases from 37.7 W/m37.7\text{ W}/\text{m} to 29.2 W/m29.2\text{ W}/\text{m}.

    Your conclusion contradicts your own calculated numbers (29.2 W/m<37.7 W/m29.2\text{ W}/\text{m} < 37.7\text{ W}/\text{m}) and the critical radius rule. Because the initial radius r1=10.0 mmr_1 = 10.0\text{ mm} already exceeds rcr=4.00 mmr_{\text{cr}} = 4.00\text{ mm}, any additional insulation increases conductive resistance more than it decreases convective resistance, so heat loss decreases.

WHAT YOU DID WELL
Compliments from Your Teacher

You correctly computed the critical radius of insulation using rcr=k/hr_{\text{cr}} = k/h.

You correctly determined the thermal resistances and heat transfer rates per unit length for both the bare and insulated configurations.

THE ERROR
Where Your ACEpath Teacher Spotted the Mistake
Critical Radius Misinterpretation

none

WHY IT HAPPENED
ACEpath Teacher's Diagnosis

You relied on a generalized qualitative intuition that adding insulation to small or thin cylinders always increases heat transfer, without comparing the pipe's initial outer radius r1r_1 to the critical radius rcrr_{\text{cr}} or checking your own calculated values of Q˙′\dot{Q}'.

REASONING PATH
Your ACEpath teacher’s suggested approach
Compare $r_1$ to $r_{\text{cr}}$
  • If initial radius r1>rcrr_1 > r_{\text{cr}}, total thermal resistance increases with insulation (dR′/dr>0dR'/dr > 0), meaning heat loss strictly decreases.

  • Check whether r1<rcrr_1 < r_{\text{cr}} or r1>rcrr_1 > r_{\text{cr}} before concluding whether heat loss increases or decreases.

Verify consistency with calculated values
  • A qualitative conclusion must agree with your quantitative values: if Q˙ins′<Q˙bare′\dot{Q}'_{\text{ins}} < \dot{Q}'_{\text{bare}}, heat loss has decreased.

  • Compare Q˙ins′\dot{Q}'_{\text{ins}} directly against Q˙bare′\dot{Q}'_{\text{bare}} as a final sanity check.

CORRECTED PATH
ACEpath Teacher's Demonstration
  1. Compare the two calculated heat loss rates: Q˙bare′=37.7 W/m\dot{Q}'_{\text{bare}} = 37.7\text{ W}/\text{m} and Q˙ins′=29.2 W/m\dot{Q}'_{\text{ins}} = 29.2\text{ W}/\text{m}.

  2. Observe that Q˙ins′<Q˙bare′\dot{Q}'_{\text{ins}} < \dot{Q}'_{\text{bare}}, representing a reduction in heat loss.

  3. Explain using critical radius: because the bare pipe radius r1=10.0 mmr_1 = 10.0\text{ mm} is already larger than rcr=4.00 mmr_{\text{cr}} = 4.00\text{ mm}, adding insulation places the system in the regime where conductive resistance dominates convective surface expansion, thereby decreasing heat loss.

Final answer

(a) rcr=4.00 mmr_{\text{cr}} = 4.00\text{ mm}; (b) Q˙bare′=37.7 W/m\dot{Q}'_{\text{bare}} = 37.7\text{ W}/\text{m}, Q˙ins′≈29.2 W/m\dot{Q}'_{\text{ins}} \approx 29.2\text{ W}/\text{m} (or 32.4 W/m32.4\text{ W}/\text{m} if using rounded intermediate parameters). Adding this insulation decreases the rate of heat loss.

NEXT STEPS
Final Takeaways from Your Teacher
  • Practice sketching the curve of total thermal resistance R′R' versus outer radius rr to visually identify the minimum at r=rcrr = r_{\text{cr}}.

  • Whenever an evaluation asks if heat transfer increases or decreases, immediately check whether the starting radius r1r_1 lies to the left (r1<rcrr_1 < r_{\text{cr}}) or to the right (r1>rcrr_1 > r_{\text{cr}}) of the critical radius.

OverviewACEpath Teacher's Diagnosis

03 The student uses the plane wall conduction formula rather than the cylindrical logarithmic formula for the insulation layer resistance.

Sample Student Work

Reviewed by ACEpath Teacher
Step-by-Step Review
Walk Through It with Your Teacher
Partially correct
  1. Step 1

    rcr=kh=0.040010.0=0.00400 m=4.00 mmr_{\text{cr}} = \frac{k}{h} = \frac{0.0400}{10.0} = 0.00400\text{ m} = 4.00\text{ mm}

  2. Step 2

    Rbare′=12π⋅0.0100⋅10.0=1.592 m⋅K/W  ⟹  Q˙bare′=60.01.592=37.7 W/mR'_{\text{bare}} = \frac{1}{2\pi \cdot 0.0100 \cdot 10.0} = 1.592\text{ m}\cdot\text{K/W} \implies \dot{Q}'_{\text{bare}} = \frac{60.0}{1.592} = 37.7\text{ W/m}

  3. Step 3

    Rcond′=r2−r12π⋅r1⋅k=0.002002π⋅0.0100⋅0.0400=0.796 m⋅K/WR'_{\text{cond}} = \frac{r_2 - r_1}{2\pi \cdot r_1 \cdot k} = \frac{0.00200}{2\pi \cdot 0.0100 \cdot 0.0400} = 0.796\text{ m}\cdot\text{K/W}

    Correct

    Rcond′=ln⁡(r2/r1)2πk=ln⁡(0.0120/0.0100)2π(0.0400)≈0.7254 m⋅K/WR'_{\text{cond}} = \frac{\ln(r_2/r_1)}{2\pi k} = \frac{\ln(0.0120/0.0100)}{2\pi(0.0400)} \approx 0.7254\text{ m}\cdot\text{K/W}

    In cylindrical coordinates, the area through which heat conducts varies with radius rr, so integrating Fourier's law yields Rcond′=ln⁡(r2/r1)2πkR'_{\text{cond}} = \frac{\ln(r_2/r_1)}{2\pi k} rather than a flat-slab formula using the inner perimeter.

  4. Step 4

    Rconv′=12π⋅0.0120⋅10.0=1.326 m⋅K/WR'_{\text{conv}} = \frac{1}{2\pi \cdot 0.0120 \cdot 10.0} = 1.326\text{ m}\cdot\text{K/W}

  5. Step 5

    Rtotal′=0.796+1.326=2.122 m⋅K/W  ⟹  Q˙ins′=60.02.122=28.3 W/mR'_{\text{total}} = 0.796 + 1.326 = 2.122\text{ m}\cdot\text{K/W} \implies \dot{Q}'_{\text{ins}} = \frac{60.0}{2.122} = 28.3\text{ W/m}

    Correct

    Rtotal′=0.7254+1.3263=2.0517 m⋅K/W  ⟹  Q˙ins′=60.02.0517≈32.4 W/mR'_{\text{total}} = 0.7254 + 1.3263 = 2.0517\text{ m}\cdot\text{K/W} \implies \dot{Q}'_{\text{ins}} = \frac{60.0}{2.0517} \approx 32.4\text{ W/m}

    Your arithmetic was carried out consistently, but your resulting insulated heat loss rate was shifted by using the incorrect conduction resistance from Step 3.

  6. Step 6

    Adding insulation decreases heat loss since 28.3 W/m<37.7 W/m.\text{Adding insulation decreases heat loss since } 28.3\text{ W/m} < 37.7\text{ W/m}.

WHAT YOU DID WELL
Compliments from Your Teacher

You calculated the critical radius of insulation correctly as 4.00 mm4.00\text{ mm}.

You calculated the bare pipe convection resistance and heat transfer rate accurately.

You used the outer radius r2r_2 properly when determining the external convective resistance of the insulated pipe.

You correctly concluded that adding the insulation layer reduces heat loss.

THE ERROR
Where Your ACEpath Teacher Spotted the Mistake
Geometry-specific conduction formula error

none

WHY IT HAPPENED
ACEpath Teacher's Diagnosis

You treated the cylindrical shell as a flat plane of constant surface area 2πr1L2\pi r_1 L across its thickness, forgetting that radial conduction area grows as 2πrL2\pi r L, which gives the logarithmic resistance ln⁡(r2/r1)2πkL\frac{\ln(r_2/r_1)}{2\pi k L}.

REASONING PATH
Your ACEpath teacher’s suggested approach
Cylindrical Conduction Resistance
  • For a cylindrical shell of inner radius r1r_1 and outer radius r2r_2, thermal resistance per unit length is Rcond′=ln⁡(r2/r1)2πkR'_{\text{cond}} = \frac{\ln(r_2/r_1)}{2\pi k}.

  • Always use the natural logarithm ratio of outer-to-inner radii for cylindrical layers instead of Δr/A\Delta r / A.

Critical Radius Rule
  • If the bare cylinder radius r1>rcr=k/hr_1 > r_{\text{cr}} = k/h, adding any insulation will always increase total thermal resistance and decrease heat loss.

  • Compare r1r_1 to rcrr_{\text{cr}} immediately to verify whether heat loss should increase or decrease.

CORRECTED PATH
ACEpath Teacher's Demonstration
  1. Use the cylindrical conduction resistance formula: Rcond′=ln⁡(r2/r1)2πk=ln⁡(0.0120/0.0100)2π(0.0400)=ln⁡(1.2)0.0800π≈0.7254 m⋅K/WR'_{\text{cond}} = \frac{\ln(r_2/r_1)}{2\pi k} = \frac{\ln(0.0120/0.0100)}{2\pi(0.0400)} = \frac{\ln(1.2)}{0.0800\pi} \approx 0.7254\text{ m}\cdot\text{K/W}.

  2. Sum the correct series resistances: Rtotal′=Rcond′+Rconv′=0.7254+1.3263=2.0517 m⋅K/WR'_{\text{total}} = R'_{\text{cond}} + R'_{\text{conv}} = 0.7254 + 1.3263 = 2.0517\text{ m}\cdot\text{K/W}.

  3. Calculate the corrected insulated heat loss rate: Q˙ins′=Ti−T∞Rtotal′=80.0−20.02.0517≈32.4 W/m\dot{Q}'_{\text{ins}} = \frac{T_i - T_{\infty}}{R'_{\text{total}}} = \frac{80.0 - 20.0}{2.0517} \approx 32.4\text{ W/m}.

Final answer

(a) rcr=4.00 mmr_{\text{cr}} = 4.00\text{ mm}; (b) Q˙bare′=37.7 W/m\dot{Q}'_{\text{bare}} = 37.7\text{ W/m}, Q˙ins′=32.4 W/m\dot{Q}'_{\text{ins}} = 32.4\text{ W/m}. Adding insulation decreases the rate of heat loss.

NEXT STEPS
Final Takeaways from Your Teacher
  • Review the derivation of thermal resistance for plane walls, cylindrical shells, and spherical shells from Fourier's law.

  • Practice calculating total thermal resistance networks for multi-layered insulated pipes.

Lock it in

Similar question

01

An electrical transmission cable has an outer radius of r1=5.0 mmr_1 = 5.0\text{ mm}. It is to be covered with plastic insulation of thermal conductivity k=0.12 W/(m⋅K)k = 0.12\text{ W}/(\text{m}\cdot\text{K}). The heat transfer coefficient to ambient air is h=15 W/(m2⋅K)h = 15\text{ W}/(\text{m}^2\cdot\text{K}). Calculate the critical radius of insulation and state whether a 1.0 mm1.0\text{ mm} thick layer of insulation increases or decreases heat dissipation.

Answer

rcr=kh=0.1215=0.008 m=8.0 mmr_{\text{cr}} = \frac{k}{h} = \frac{0.12}{15} = 0.008\text{ m} = 8.0\text{ mm}. Adding 1.0 mm1.0\text{ mm} thickness makes the outer radius r2=6.0 mmr_2 = 6.0\text{ mm}. Since r1<r2<rcrr_1 < r_2 < r_{\text{cr}}, adding this insulation increases heat dissipation.

02

A spherical chemical storage tank of radius r1=0.50 mr_1 = 0.50\text{ m} is insulated with a material having k=0.050 W/(m⋅K)k = 0.050\text{ W}/(\text{m}\cdot\text{K}) in an environment with convection coefficient h=5.0 W/(m2⋅K)h = 5.0\text{ W}/(\text{m}^2\cdot\text{K}). Find the critical radius of insulation rcrr_{\text{cr}}, and explain whether adding insulation to this tank can ever increase heat transfer.

Answer

For a sphere, rcr=2kh=2(0.050)5.0=0.020 m=20 mmr_{\text{cr}} = \frac{2k}{h} = \frac{2(0.050)}{5.0} = 0.020\text{ m} = 20\text{ mm}. Since the bare tank radius r1=0.50 m=500 mm≫rcrr_1 = 0.50\text{ m} = 500\text{ mm} \gg r_{\text{cr}}, any added insulation strictly increases total thermal resistance and decreases heat transfer.

03

A steam pipe with outer radius r1=20 mmr_1 = 20\text{ mm} carries steam at 120∘C120^{\circ}\text{C} in ambient air at 20∘C20^{\circ}\text{C} with h=8.0 W/(m2⋅K)h = 8.0\text{ W}/(\text{m}^2\cdot\text{K}). (a) Find rcrr_{\text{cr}} if k=0.040 W/(m⋅K)k = 0.040\text{ W}/(\text{m}\cdot\text{K}). (b) Calculate the percentage change in heat loss per unit length if a 5.0 mm5.0\text{ mm} layer of this insulation is added.

Answer

(a) rcr=kh=0.0408.0=5.0 mmr_{\text{cr}} = \frac{k}{h} = \frac{0.040}{8.0} = 5.0\text{ mm}. (b) Bare: Rbare′=12π(0.020)(8.0)≈0.995 m⋅K/W  ⟹  Q˙bare′=1000.995≈100.5 W/mR'_{\text{bare}} = \frac{1}{2\pi(0.020)(8.0)} \approx 0.995\text{ m}\cdot\text{K}/\text{W} \implies \dot{Q}'_{\text{bare}} = \frac{100}{0.995} \approx 100.5\text{ W}/\text{m}. Insulated (r2=25 mmr_2 = 25\text{ mm}): Rcond′=ln⁡(25/20)2π(0.040)≈0.888 m⋅K/WR'_{\text{cond}} = \frac{\ln(25/20)}{2\pi(0.040)} \approx 0.888\text{ m}\cdot\text{K}/\text{W}, Rconv′=12π(0.025)(8.0)≈0.796 m⋅K/W  ⟹  Rtotal′=1.684 m⋅K/W  ⟹  Q˙ins′=1001.684≈59.4 W/mR'_{\text{conv}} = \frac{1}{2\pi(0.025)(8.0)} \approx 0.796\text{ m}\cdot\text{K}/\text{W} \implies R'_{\text{total}} = 1.684\text{ m}\cdot\text{K}/\text{W} \implies \dot{Q}'_{\text{ins}} = \frac{100}{1.684} \approx 59.4\text{ W}/\text{m}. Heat loss decreases by 100.5−59.4100.5×100%≈40.9%\frac{100.5 - 59.4}{100.5} \times 100\% \approx 40.9\%.

Loading workspace…