Resources

A horizontal Venturi meter is installed in an oil delivery line transporting an incompressible, non-viscous fluid with density ρ=850 kg/m3\rho = 850\text{ kg/m}^3. In the main pipeline where the diameter is D1=0.200 mD_1 = 0.200\text{ m}, the fluid flows with a speed of v1=1.50 m/sv_1 = 1.50\text{ m/s}. The fluid then passes into a constricted throat section. Two vertical open piezometer tubes tapped into the pipe wall indicate a static pressure head difference of Δh=0.450 m\Delta h = 0.450\text{ m} between the wide section and the throat. Taking g=9.80 m/s2g = 9.80\text{ m/s}^2, calculate the inner diameter D2D_2 of the constricted throat.

Answer and steps

Final answer

D2=0.134 mD_2 = 0.134\text{ m}

Steps

01

Relate Static Pressure Difference to Velocity (Bernoulli's Principle)

For a horizontal, steady, incompressible, and non-viscous fluid flow, Bernoulli's equation between the wide section (point 1) and the throat (point 2) is:

P1+12ρv12=P2+12ρv22P_1 + \frac{1}{2}\rho v_1^2 = P_2 + \frac{1}{2}\rho v_2^2

Rearranging for the pressure difference gives:

P1−P2=12ρ(v22−v12)P_1 - P_2 = \frac{1}{2}\rho (v_2^2 - v_1^2)

The open vertical piezometer tubes measure the static pressure of the flowing fluid directly as a hydrostatic liquid column height (P=ρghP = \rho g h). The difference in piezometer column levels Δh\Delta h relates to the pressure difference by:

P1−P2=ρgΔhP_1 - P_2 = \rho g \Delta h

Equating both expressions for P1−P2P_1 - P_2:

ρgΔh=12ρ(v22−v12)\rho g \Delta h = \frac{1}{2}\rho (v_2^2 - v_1^2)

Notice that the fluid density ρ\rho cancels out:

2gΔh=v22−v122g \Delta h = v_2^2 - v_1^2

Solving for the flow speed in the throat v2v_2:

v2=v12+2gΔhv_2 = \sqrt{v_1^2 + 2g\Delta h}

Substitute the given values:

  • v1=1.50 m/sv_1 = 1.50\text{ m/s}
  • g=9.80 m/s2g = 9.80\text{ m/s}^2
  • Δh=0.450 m\Delta h = 0.450\text{ m}

v2=(1.50)2+2(9.80)(0.450)=2.25+8.82=11.07≈3.327 m/sv_2 = \sqrt{(1.50)^2 + 2(9.80)(0.450)} = \sqrt{2.25 + 8.82} = \sqrt{11.07} \approx 3.327\text{ m/s}


02

Apply the Continuity Equation to Find the Throat Diameter

For an incompressible fluid, the volume flow rate remains constant throughout the pipe:

A1v1=A2v2A_1 v_1 = A_2 v_2

Expressing the circular cross-sectional areas in terms of their diameters (A=πD24A = \frac{\pi D^2}{4}):

πD124v1=πD224v2  ⟹  D12v1=D22v2\frac{\pi D_1^2}{4} v_1 = \frac{\pi D_2^2}{4} v_2 \implies D_1^2 v_1 = D_2^2 v_2

Solving for the throat diameter D2D_2:

D2=D1v1v2D_2 = D_1 \sqrt{\frac{v_1}{v_2}}

Common Pitfall: A frequent mistake is assuming the diameter scales linearly with velocity (D2=D1v1v2D_2 = D_1 \frac{v_1}{v_2}). Because cross-sectional area is proportional to the square of diameter (A∝D2A \propto D^2), the diameter is proportional to the square root of the velocity ratio: D∝1vD \propto \frac{1}{\sqrt{v}}.

Substitute the values:

D2=0.200 m×1.50 m/s3.327 m/s=0.200×0.45085≈0.200×0.6715≈0.134 mD_2 = 0.200\text{ m} \times \sqrt{\frac{1.50\text{ m/s}}{3.327\text{ m/s}}} = 0.200 \times \sqrt{0.45085} \approx 0.200 \times 0.6715 \approx 0.134\text{ m}

Typical errors

OverviewACEpath Teacher's Diagnosis

01 The student forgets that flow cross-sectional area is proportional to the square of diameter and uses a linear relationship between diameter and velocity in the continuity equation.

Sample Student Work

Reviewed by ACEpath Teacher
Step-by-Step Review
Walk Through It with Your Teacher
Incorrect
  1. Step 1

    P1−P2=ρgΔh  ⟹  v2=v12+2gΔh=(1.50)2+2(9.80)(0.450)=3.327 m/sP_1 - P_2 = \rho g \Delta h \implies v_2 = \sqrt{v_1^2 + 2g\Delta h} = \sqrt{(1.50)^2 + 2(9.80)(0.450)} = 3.327\text{ m/s}

  2. Step 2

    D1v1=D2v2D_1 v_1 = D_2 v_2

    Correct

    A1v1=A2v2  ⟹  D12v1=D22v2A_1 v_1 = A_2 v_2 \implies D_1^2 v_1 = D_2^2 v_2

    The continuity equation equates volume flow rate A1v1=A2v2A_1 v_1 = A_2 v_2. Since the cross-sectional area of a circular pipe is A=πD24A = \frac{\pi D^2}{4}, the velocities are inversely proportional to the square of the diameters (D2D^2), not to the diameters directly.

  3. Step 3

    D2=D1(v1/v2)=0.200×(1.503.327)=0.0902 mD_2 = D_1 (v_1/v_2) = 0.200 \times \left(\frac{1.50}{3.327}\right) = 0.0902\text{ m}

    Correct

    D2=D1v1v2=0.200×1.503.327≈0.134 mD_2 = D_1 \sqrt{\frac{v_1}{v_2}} = 0.200 \times \sqrt{\frac{1.50}{3.327}} \approx 0.134\text{ m}

    Because of the missing exponent on the diameters in the continuity equation, your final numerical value for D2D_2 is incorrect.

WHAT YOU DID WELL
Compliments from Your Teacher

You correctly linked the piezometer height difference to the static pressure drop across the Venturi meter.

You accurately solved for the throat velocity v2=3.327 m/sv_2 = 3.327\text{ m/s} using Bernoulli's equation.

THE ERROR
Where Your ACEpath Teacher Spotted the Mistake
Linear diameter scaling in continuity equation

no

WHY IT HAPPENED
ACEpath Teacher's Diagnosis

You treated the continuity equation as a direct linear relationship between velocity and diameter (D1v1=D2v2D_1 v_1 = D_2 v_2) rather than relating velocity to cross-sectional area (A1v1=A2v2A_1 v_1 = A_2 v_2, where A∝D2A \propto D^2).

REASONING PATH
Your ACEpath teacher’s suggested approach
Continuity Area-Diameter Relationship
  • For circular cross-sections, area scales as A=πD24A = \frac{\pi D^2}{4}. Thus, A1v1=A2v2A_1 v_1 = A_2 v_2 simplifies to D12v1=D22v2D_1^2 v_1 = D_2^2 v_2.

  • Always write out A1v1=A2v2A_1 v_1 = A_2 v_2 first, then substitute A=πD24A = \frac{\pi D^2}{4} before solving for diameter.

CORRECTED PATH
ACEpath Teacher's Demonstration
  1. Write the continuity equation for circular pipes: D12v1=D22v2D_1^2 v_1 = D_2^2 v_2.

  2. Isolate D2D_2: D2=D1v1v2D_2 = D_1 \sqrt{\frac{v_1}{v_2}}.

  3. Substitute the known values: D2=0.200 m×1.50 m/s3.327 m/s=0.200×0.45085≈0.134 mD_2 = 0.200\text{ m} \times \sqrt{\frac{1.50\text{ m/s}}{3.327\text{ m/s}}} = 0.200 \times \sqrt{0.45085} \approx 0.134\text{ m}.

Final answer

D2=0.134 mD_2 = 0.134\text{ m}

NEXT STEPS
Final Takeaways from Your Teacher
  • Review the geometric relationship between circular area and diameter (A∝D2A \propto D^2).

  • Practice rearranging the continuity equation directly in terms of radius and diameter to make the square root relationship automatic.

OverviewACEpath Teacher's Diagnosis

02 The student inverts the velocity ratio in the continuity equation, setting D₂ = D₁√(v₂/v₁) instead of D₁√(v₁/v₂), which yields an unphysical throat diameter larger than the main pipe.

Sample Student Work

Reviewed by ACEpath Teacher
Step-by-Step Review
Walk Through It with Your Teacher
Incorrect
  1. Step 1

    v22−v12=2gΔh  ⟹  v2=1.502+2×9.80×0.450=11.07=3.327 m/sv_2^2 - v_1^2 = 2g\Delta h \implies v_2 = \sqrt{1.50^2 + 2 \times 9.80 \times 0.450} = \sqrt{11.07} = 3.327\text{ m/s}

  2. Step 2

    D2=D1v2v1D_2 = D_1 \sqrt{\frac{v_2}{v_1}}

    Correct

    D2=D1v1v2D_2 = D_1 \sqrt{\frac{v_1}{v_2}}

    You inverted the velocity ratio in the continuity equation. Since A1v1=A2v2A_1 v_1 = A_2 v_2, we have D12v1=D22v2D_1^2 v_1 = D_2^2 v_2, which yields D2=D1v1/v2D_2 = D_1 \sqrt{v_1 / v_2}.

  3. Step 3

    D2=0.200×3.3271.50=0.200×1.490=0.298 mD_2 = 0.200 \times \sqrt{\frac{3.327}{1.50}} = 0.200 \times 1.490 = 0.298\text{ m}

    Correct

    D2=0.200×1.503.327≈0.134 mD_2 = 0.200 \times \sqrt{\frac{1.50}{3.327}} \approx 0.134\text{ m}

    Because of the inverted formula from the previous step, your computed throat diameter ended up larger than the main pipe diameter (0.298 m>0.200 m0.298\text{ m} > 0.200\text{ m}).

WHAT YOU DID WELL
Compliments from Your Teacher

You correctly applied Bernoulli's principle to find the fluid velocity in the throat.

You recognized that pipe diameter scales with the square root of velocity.

THE ERROR
Where Your ACEpath Teacher Spotted the Mistake
Inverted Continuity Ratio

You accidentally placed v2v_2 in the numerator and v1v_1 in the denominator when isolating D2D_2.

WHY IT HAPPENED
ACEpath Teacher's Diagnosis

Algebraic isolation error in the continuity equation: confusing the inverse relationship between speed and cross-sectional area with a direct relationship.

REASONING PATH
Your ACEpath teacher’s suggested approach
Continuity Equation Relationship
  • For incompressible flow, A1v1=A2v2A_1 v_1 = A_2 v_2, meaning area and velocity are inversely proportional (A∝1/vA \propto 1/v).

  • Solve step-by-step: D22=D12(v1/v2)D_2^2 = D_1^2 (v_1 / v_2) before taking the square root.

Physical Reality Check
  • A constricted throat section must have a smaller diameter than the inlet pipe (D2<D1D_2 < D_1).

  • Always compare your calculated throat diameter with the initial diameter; if the throat is larger while fluid speeds up, recheck the ratio.

CORRECTED PATH
ACEpath Teacher's Demonstration
  1. Set up the continuity equation: A1v1=A2v2  ⟹  D12v1=D22v2A_1 v_1 = A_2 v_2 \implies D_1^2 v_1 = D_2^2 v_2

  2. Isolate the unknown diameter: D2=D1v1v2D_2 = D_1 \sqrt{\frac{v_1}{v_2}}

  3. Substitute the known values: D2=0.200 m×1.503.327=0.200×0.6715≈0.134 mD_2 = 0.200\text{ m} \times \sqrt{\frac{1.50}{3.327}} = 0.200 \times 0.6715 \approx 0.134\text{ m}

Final answer

D2=0.134 mD_2 = 0.134\text{ m}

NEXT STEPS
Final Takeaways from Your Teacher
  • Review the algebraic steps when rearranging A1v1=A2v2A_1 v_1 = A_2 v_2 to isolate D2D_2.

  • Perform a sanity check on flow geometry: fluid speeds up where the pipe narrows, so higher velocity must always correspond to a smaller diameter.

OverviewACEpath Teacher's Diagnosis

03 The student omits the initial kinetic energy term v₁² in Bernoulli's equation, assuming v₂ = √(2gΔh).

Sample Student Work

Reviewed by ACEpath Teacher
Step-by-Step Review
Walk Through It with Your Teacher
Incorrect
  1. Step 1

    v2=2gΔh  ⟹  v2=2×9.80×0.450=8.82=2.970 m/sv_2 = \sqrt{2g\Delta h} \implies v_2 = \sqrt{2 \times 9.80 \times 0.450} = \sqrt{8.82} = 2.970\text{ m/s}

    Correct

    v2=v12+2gΔh=(1.50)2+2(9.80)(0.450)=11.07≈3.327 m/sv_2 = \sqrt{v_1^2 + 2g\Delta h} = \sqrt{(1.50)^2 + 2(9.80)(0.450)} = \sqrt{11.07} \approx 3.327\text{ m/s}

    You treated the pressure head difference as if the fluid was discharging from rest (v1=0v_1 = 0), using Torricelli's formula instead of the full Bernoulli equation. Because the oil enters the constricted section already moving at v1=1.50 m/sv_1 = 1.50\text{ m/s}, the kinetic energy balance is 12ρ(v22−v12)=ρgΔh\frac{1}{2}\rho (v_2^2 - v_1^2) = \rho g \Delta h.

  2. Step 2

    D2=D1v1v2  ⟹  D2=0.200×1.502.970=0.200×0.7107=0.142 mD_2 = D_1 \sqrt{\frac{v_1}{v_2}} \implies D_2 = 0.200 \times \sqrt{\frac{1.50}{2.970}} = 0.200 \times 0.7107 = 0.142\text{ m}

    Correct

    D2=D1v1v2=0.200×1.503.327≈0.134 mD_2 = D_1 \sqrt{\frac{v_1}{v_2}} = 0.200 \times \sqrt{\frac{1.50}{3.327}} \approx 0.134\text{ m}

    Your continuity formula and arithmetic are correct, but your final throat diameter was affected by the incorrect throat speed from Step 1.

WHAT YOU DID WELL
Compliments from Your Teacher

You correctly related the pipe diameter ratio to the inverse square root of the velocity ratio using the continuity equation.

You accurately substituted your calculated values and performed the square-root arithmetic.

THE ERROR
Where Your ACEpath Teacher Spotted the Mistake
Omission of upstream velocity in Bernoulli equation

no

WHY IT HAPPENED
ACEpath Teacher's Diagnosis

You assumed Torricelli's form v=2gΔhv = \sqrt{2g\Delta h} for the constriction velocity, overlooking the non-zero upstream velocity v1v_1 in the horizontal streamline energy balance.

REASONING PATH
Your ACEpath teacher’s suggested approach
Check Upstream Flow Speed
  • In a horizontal pipe, the static pressure drop accounts for the change in kinetic energy: ΔP=12ρ(v22−v12)\Delta P = \frac{1}{2}\rho(v_2^2 - v_1^2).

  • Always write the full Bernoulli equation between points 1 and 2 before solving for v2v_2, ensuring you do not drop v12v_1^2 unless the upstream reservoir is explicitly static (v1≈0v_1 \approx 0).

CORRECTED PATH
ACEpath Teacher's Demonstration
  1. Write Bernoulli's equation for a horizontal streamline: P1+12ρv12=P2+12ρv22P_1 + \frac{1}{2}\rho v_1^2 = P_2 + \frac{1}{2}\rho v_2^2.

  2. Express the pressure difference using the piezometer head difference: P1−P2=ρgΔhP_1 - P_2 = \rho g \Delta h.

  3. Equate the expressions: ρgΔh=12ρ(v22−v12)  ⟹  v2=v12+2gΔh\rho g \Delta h = \frac{1}{2}\rho(v_2^2 - v_1^2) \implies v_2 = \sqrt{v_1^2 + 2g\Delta h}.

  4. Calculate v2=(1.50)2+2(9.80)(0.450)=2.25+8.82=11.07≈3.327 m/sv_2 = \sqrt{(1.50)^2 + 2(9.80)(0.450)} = \sqrt{2.25 + 8.82} = \sqrt{11.07} \approx 3.327\text{ m/s}.

  5. Substitute v2v_2 into the continuity relationship: D2=D1v1v2=0.200×1.503.327≈0.134 mD_2 = D_1\sqrt{\frac{v_1}{v_2}} = 0.200 \times \sqrt{\frac{1.50}{3.327}} \approx 0.134\text{ m}.

Final answer

D2=0.134 mD_2 = 0.134\text{ m}

NEXT STEPS
Final Takeaways from Your Teacher
  • Review the derivation of the Venturi effect from Bernoulli's principle to see why both kinetic energy terms must be retained.

  • Practice solving Venturi meter problems where both the inlet velocity and the manometer head difference are non-zero.

Lock it in

Similar question

01

Water flows through a horizontal pipe with diameter D1=0.10 mD_1 = 0.10\text{ m} at a speed of v1=2.0 m/sv_1 = 2.0\text{ m/s}. The pipe narrows to a throat of diameter D2=0.050 mD_2 = 0.050\text{ m}. Calculate the fluid velocity v2v_2 in the throat.

Answer

v2=8.0 m/sv_2 = 8.0\text{ m/s}. Using continuity: D12v1=D22v2  ⟹  v2=v1(D1D2)2=2.0×(0.100.050)2=2.0×4=8.0 m/sD_1^2 v_1 = D_2^2 v_2 \implies v_2 = v_1 \left(\frac{D_1}{D_2}\right)^2 = 2.0 \times \left(\frac{0.10}{0.050}\right)^2 = 2.0 \times 4 = 8.0\text{ m/s}.

02

A horizontal Venturi meter carries water. In the main section where D1=12.0 cmD_1 = 12.0\text{ cm}, the speed is v1=1.20 m/sv_1 = 1.20\text{ m/s}. If the speed in the throat is measured to be v2=4.80 m/sv_2 = 4.80\text{ m/s}, determine the throat diameter D2D_2 and the pressure drop ΔP=P1−P2\Delta P = P_1 - P_2 (density ρ=1000 kg/m3\rho = 1000\text{ kg/m}^3).

Answer

D2=6.00 cmD_2 = 6.00\text{ cm} and ΔP=1.08×104 Pa\Delta P = 1.08 \times 10^4\text{ Pa}. By continuity: D2=D1v1/v2=12.0×1.20/4.80=6.00 cmD_2 = D_1 \sqrt{v_1/v_2} = 12.0 \times \sqrt{1.20/4.80} = 6.00\text{ cm}. By Bernoulli: ΔP=12ρ(v22−v12)=0.5×1000×(4.802−1.202)=500×(23.04−1.44)=10800 Pa\Delta P = \frac{1}{2}\rho (v_2^2 - v_1^2) = 0.5 \times 1000 \times (4.80^2 - 1.20^2) = 500 \times (23.04 - 1.44) = 10800\text{ Pa}.

03

An oil pipeline (D1=30.0 cmD_1 = 30.0\text{ cm}) carries oil (density ρ=800 kg/m3\rho = 800\text{ kg/m}^3) with an inlet velocity of v1=2.00 m/sv_1 = 2.00\text{ m/s}. A Venturi restriction creates a static head difference of Δh=0.800 m\Delta h = 0.800\text{ m} in vertical open tubes (g=9.80 m/s2g = 9.80\text{ m/s}^2). Find the required throat diameter D2D_2.

Answer

D2=0.207 mD_2 = 0.207\text{ m}. First, find throat velocity using Bernoulli: v2=v12+2gΔh=2.002+2(9.80)(0.800)=4.00+15.68=19.68≈4.436 m/sv_2 = \sqrt{v_1^2 + 2g\Delta h} = \sqrt{2.00^2 + 2(9.80)(0.800)} = \sqrt{4.00 + 15.68} = \sqrt{19.68} \approx 4.436\text{ m/s}. Then, apply continuity with area scaling: D2=D1v1/v2=0.300×2.00/4.436≈0.300×0.6714≈0.201 mD_2 = D_1 \sqrt{v_1/v_2} = 0.300 \times \sqrt{2.00 / 4.436} \approx 0.300 \times 0.6714 \approx 0.201\text{ m} (or 0.201 m0.201\text{ m}).

Loading workspace…