Resources

An electric utility engineer models the current density vector J⃗\vec{J} in a conducting alloy slab under an applied electric field E⃗=(120 i^−160 j^) V/m\vec{E} = (120\,\hat{i} - 160\,\hat{j})\text{ V}/\text{m}. The material obeys Ohm's law J⃗=σE⃗\vec{J} = \sigma \vec{E}, where the electrical conductivity is σ=3.50×104 S/m\sigma = 3.50 \times 10^4\text{ S}/\text{m} (where 1 S=1 Ω−1=1 A/V1\text{ S} = 1\,\Omega^{-1} = 1\text{ A}/\text{V}). (a) Verify the base SI units of current density J⃗\vec{J} obtained from σE⃗\sigma \vec{E}. (b) Determine the exact direction of the resulting current density vector J⃗\vec{J}, expressed as a counterclockwise angle θ\theta measured from the positive xx-axis (in the range [0∘,360∘)[0^\circ, 360^\circ)).](streamdown:incomplete-link)

Answer and steps

Final answer

(a) Base SI units are A/m2\text{A}/\text{m}^2; (b) θ=307∘\theta = 307^\circ (or 53.1∘53.1^\circ clockwise from the +x+x-axis).

Steps

Part (a): Dimensional Analysis and Base SI Units

  1. Express the units of conductivity and electric field:

    • The electrical conductivity σ\sigma is given in siemens per meter (S/m\text{S}/\text{m}). Since 1 S=1 A/V1\text{ S} = 1\text{ A}/\text{V}, we have: [σ]=AV⋅m[\sigma] = \frac{\text{A}}{\text{V}\cdot\text{m}}
    • The electric field E⃗\vec{E} is given in volts per meter: [E⃗]=Vm[\vec{E}] = \frac{\text{V}}{\text{m}}
  2. Compute the product of their units: Using the microscopic form of Ohm's law, J⃗=σE⃗\vec{J} = \sigma \vec{E}: [J⃗]=[σ][E⃗]=(AV⋅m)(Vm)=Am2[\vec{J}] = [\sigma][\vec{E}] = \left(\frac{\text{A}}{\text{V}\cdot\text{m}}\right) \left(\frac{\text{V}}{\text{m}}\right) = \frac{\text{A}}{\text{m}^2}
  3. Verify against base SI units: The ampere (A\text{A}) is the base SI unit of electric current, and the meter (m\text{m}) is the base SI unit of length. Therefore, the base SI unit representation of current density is A/m2\text{A}/\text{m}^2, which represents electric current per unit cross-sectional area.

Part (b): Direction of the Current Density Vector

  1. Relate the directions of J⃗\vec{J} and E⃗\vec{E}: Because conductivity σ=3.50×104 S/m\sigma = 3.50 \times 10^4\text{ S}/\text{m} is a positive scalar quantity, J⃗\vec{J} is parallel to and points in the exact same direction as E⃗\vec{E}.
  2. Identify the components: The components of the vector are:

    • Ex=120 V/mE_x = 120\text{ V}/\text{m} (>0> 0)
    • Ey=−160 V/mE_y = -160\text{ V}/\text{m} (<0< 0)

    Since the xx-component is positive and the yy-component is negative, the vector lies in the fourth quadrant (Quadrant IV).

  3. Calculate the angle:

    • Find the reference angle ϕ\phi below the positive xx-axis: tan⁡ϕ=∣Ey∣Ex=160120=43\tan \phi = \frac{|E_y|}{E_x} = \frac{160}{120} = \frac{4}{3} ϕ=arctan⁡(43)≈53.13∘≈53.1∘\phi = \arctan\left(\frac{4}{3}\right) \approx 53.13^\circ \approx 53.1^\circ
    • Measuring counterclockwise from the positive xx-axis: θ=360∘−ϕ=360∘−53.13∘=306.87∘≈307∘\theta = 360^\circ - \phi = 360^\circ - 53.13^\circ = 306.87^\circ \approx 307^\circ

Common Pitfall: Using arctan⁡(Ey/Ex)\arctan(E_y/E_x) directly on a calculator gives −53.1∘-53.1^\circ. When standard counterclockwise angles in [0∘,360∘)[0^\circ, 360^\circ) are required, add 360∘360^\circ to negative fourth-quadrant values.](streamdown:incomplete-link)

Typical errors

OverviewACEpath Teacher's Diagnosis

01 The student calculates the reference angle using arctan(Ey/Ex) but reports the negative angle directly instead of converting it to the required range [0°, 360°).

Sample Student Work

Reviewed by ACEpath Teacher
Step-by-Step Review
Walk Through It with Your Teacher
Partially correct
  1. Step 1

    [σE]=Sm×Vm  ⟹  S=A/V  ⟹  [σE]=(AV⋅m)×(V/m)=A/m2[\sigma E] = \frac{\text{S}}{\text{m}} \times \frac{\text{V}}{\text{m}} \implies \text{S} = \text{A}/\text{V} \implies [\sigma E] = \left(\frac{\text{A}}{\text{V}\cdot\text{m}}\right) \times (\text{V}/\text{m}) = \text{A}/\text{m}^2

  2. Step 2

    tan⁡θ=EyEx=−160120=−43\tan \theta = \frac{E_y}{E_x} = \frac{-160}{120} = -\frac{4}{3}

  3. Step 3

    θ=arctan⁡(−43)=−53.13∘\theta = \arctan\left(-\frac{4}{3}\right) = -53.13^\circ

    Correct

    θ=360∘−53.13∘=306.87∘≈307∘\theta = 360^\circ - 53.13^\circ = 306.87^\circ \approx 307^\circ

    The vector lies in Quadrant IV because Ex>0E_x > 0 and Ey<0E_y < 0. While −53.13∘-53.13^\circ describes the correct geometric orientation, the prompt specifically requires the counterclockwise angle in the range [0∘,360∘)[0^\circ, 360^\circ). Adding 360∘360^\circ yields 306.87∘≈307∘306.87^\circ \approx 307^\circ.](streamdown:incomplete-link)

WHAT YOU DID WELL
Compliments from Your Teacher

You substituted the definition 1 S=1 A/V1\text{ S} = 1\text{ A}/\text{V} to verify the base SI units of current density.

You used the ratio of vector components Ey/ExE_y/E_x to find the tangent of the direction angle.

THE ERROR
Where Your ACEpath Teacher Spotted the Mistake
Angle Domain Constraint

You calculated the standard principal value from the inverse tangent function but omitted the final addition of 360∘360^\circ to map the angle into [0∘,360∘)[0^\circ, 360^\circ).](streamdown:incomplete-link)

WHY IT HAPPENED
ACEpath Teacher's Diagnosis

Directly adopting the calculator output of arctan⁡(y/x)\arctan(y/x) without adjusting for the specified coordinate domain [0∘,360∘)[0^\circ, 360^\circ) or quadrant position.](streamdown:incomplete-link)

REASONING PATH
Your ACEpath teacher’s suggested approach
Quadrant Verification
  • Examine the signs of both components (x>0,y<0x > 0, y < 0) to locate the vector in Quadrant IV before finalizing the angle.

  • Always sketch the vector or state its quadrant to determine whether you need to add 180∘180^\circ or 360∘360^\circ to the principal inverse tangent value.

Domain Compliance
  • Angles constrained to [0∘,360∘)[0^\circ, 360^\circ) must be non-negative.](streamdown:incomplete-link)

  • Whenever a calculator gives a negative angle for a Quadrant IV vector, add 360∘360^\circ to convert it into the standard positive range.

CORRECTED PATH
ACEpath Teacher's Demonstration
  1. Identify the quadrant from component signs: Ex=120>0E_x = 120 > 0 and Ey=−160<0E_y = -160 < 0, placing the vector in Quadrant IV.

  2. Find the reference angle: ϕ=arctan⁡(∣Ey∣Ex)=arctan⁡(160120)≈53.13∘\phi = \arctan\left(\frac{|E_y|}{E_x}\right) = \arctan\left(\frac{160}{120}\right) \approx 53.13^\circ.

  3. Convert to the counterclockwise angle in [0∘,360∘)[0^\circ, 360^\circ): θ=360∘−53.13∘=306.87∘≈307∘\theta = 360^\circ - 53.13^\circ = 306.87^\circ \approx 307^\circ.](streamdown:incomplete-link)

Final answer

θ=307∘\theta = 307^\circ (or 306.87∘306.87^\circ)

NEXT STEPS
Final Takeaways from Your Teacher
  • Double-check angle intervals specified in the problem statement, such as [0∘,360∘)[0^\circ, 360^\circ) vs. [−180∘,180∘)[-180^\circ, 180^\circ).](streamdown:incomplete-link)

  • Practice converting negative principal values from inverse trigonometric functions into standard counterclockwise angles.

OverviewACEpath Teacher's Diagnosis

02 The student adds 180° to the negative angle instead of 360°, confusing Quadrant IV vector placement with Quadrant II.

Sample Student Work

Reviewed by ACEpath Teacher
Step-by-Step Review
Walk Through It with Your Teacher
Partially correct
  1. Step 1

    [σ]=Sm=AV⋅m  ⟹  [E]=Vm  ⟹  [J]=[σ][E]=(AV⋅m)×(Vm)=Am2[\sigma] = \frac{\text{S}}{\text{m}} = \frac{\text{A}}{\text{V}\cdot\text{m}} \implies [E] = \frac{\text{V}}{\text{m}} \implies [J] = [\sigma][E] = \left(\frac{\text{A}}{\text{V}\cdot\text{m}}\right) \times \left(\frac{\text{V}}{\text{m}}\right) = \frac{\text{A}}{\text{m}^2}

  2. Step 2

    tan⁡θ=EyEx=−160120=−1.333  ⟹  arctan⁡(−1.333)=−53.13∘\tan\theta = \frac{E_y}{E_x} = \frac{-160}{120} = -1.333 \implies \arctan(-1.333) = -53.13^\circ

  3. Step 3

    θ=180∘−53.13∘=126.87∘\theta = 180^\circ - 53.13^\circ = 126.87^\circ

    Correct

    θ=360∘−53.13∘=306.87∘≈307∘\theta = 360^\circ - 53.13^\circ = 306.87^\circ \approx 307^\circ

    You adjusted the angle by subtracting from 180∘180^\circ, which places the vector in Quadrant II. Because Ex=120>0E_x = 120 > 0 and Ey=−160<0E_y = -160 < 0, the vector lies in Quadrant IV, so the standard counterclockwise angle from the positive xx-axis is 360∘−53.13∘=306.87∘360^\circ - 53.13^\circ = 306.87^\circ.

WHAT YOU DID WELL
Compliments from Your Teacher

You correctly performed the unit dimensional analysis to show [J]=A/m2[J] = \text{A}/\text{m}^2.

You correctly recognized that J⃗\vec{J} has the same direction as E⃗\vec{E} because conductivity σ\sigma is a positive scalar.

You accurately calculated the ratio EyEx\frac{E_y}{E_x} and evaluated arctan⁡(−1.333)\arctan(-1.333) to obtain −53.13∘-53.13^\circ.

THE ERROR
Where Your ACEpath Teacher Spotted the Mistake
Quadrant Placement Error

You treated the vector as if it were in Quadrant II (180∘−ϕ180^\circ - \phi) rather than Quadrant IV (360∘−ϕ360^\circ - \phi).

WHY IT HAPPENED
ACEpath Teacher's Diagnosis

Conflating the quadrant adjustment rule for arctan⁡(y/x)\arctan(y/x): when x>0x > 0 and y<0y < 0 (Quadrant IV), the principal value of arctan⁡\arctan is negative and requires adding 360∘360^\circ (or subtracting the reference angle from 360∘360^\circ) to express the angle in the interval [0∘,360∘)[0^\circ, 360^\circ). Adding 180∘180^\circ is reserved for Quadrants II and III where x<0x < 0.](streamdown:incomplete-link)

REASONING PATH
Your ACEpath teacher’s suggested approach
Component Sign Quadrant Check
  • Inspect the signs of (x,y)(x, y) before calculating angles: (+,+)→QI(+, +) \to \text{QI}, (−,+)→QII(-, +) \to \text{QII}, (−,−)→QIII(-, -) \to \text{QIII}, and (+,−)→QIV(+, -) \to \text{QIV}.

  • Always sketch or note the quadrant first. Since Ex>0E_x > 0 and Ey<0E_y < 0, immediately write down 'Quadrant IV' to guide your angle adjustment.

Converting Negative Calculator Angles
  • For a Quadrant IV vector where arctan⁡(y/x)=−ϕ<0\arctan(y/x) = -\phi < 0, the counterclockwise angle in [0∘,360∘)[0^\circ, 360^\circ) is θ=360∘−ϕ\theta = 360^\circ - \phi.](streamdown:incomplete-link)

  • Add 360∘360^\circ to negative calculator values in Quadrant IV rather than adding 180∘180^\circ.

CORRECTED PATH
ACEpath Teacher's Demonstration
  1. Identify that Ex=120>0E_x = 120 > 0 and Ey=−160<0E_y = -160 < 0, which places the vector J⃗\vec{J} in Quadrant IV.

  2. A negative angle of −53.13∘-53.13^\circ represents 53.13∘53.13^\circ clockwise from the positive xx-axis.

  3. To convert to a standard counterclockwise angle in [0∘,360∘)[0^\circ, 360^\circ), compute θ=360∘−53.13∘=306.87∘≈307∘\theta = 360^\circ - 53.13^\circ = 306.87^\circ \approx 307^\circ.](streamdown:incomplete-link)

Final answer

(a) A/m2\text{A}/\text{m}^2; (b) θ≈307∘\theta \approx 307^\circ (or 306.9∘306.9^\circ)

NEXT STEPS
Final Takeaways from Your Teacher
  • Practice sketching a quick coordinate cross for any 2D vector before running arctan⁡\arctan on a calculator.

  • Review the quadrant adjustment rules: add 180∘180^\circ only when x<0x < 0, and add 360∘360^\circ when x>0,y<0x > 0, y < 0 to stay in [0∘,360∘)[0^\circ, 360^\circ).](streamdown:incomplete-link)

OverviewACEpath Teacher's Diagnosis

03 The student inverts the ratio of vector components as Ex/Ey when calculating the angle from the x-axis.

Sample Student Work

Reviewed by ACEpath Teacher
Step-by-Step Review
Walk Through It with Your Teacher
Partially correct
  1. Step 1

    [σE]=(Sm)×(Vm)=(A/Vm)×Vm=A/m2[\sigma E] = \left(\frac{\text{S}}{\text{m}}\right) \times \left(\frac{\text{V}}{\text{m}}\right) = \left(\frac{\text{A}/\text{V}}{\text{m}}\right) \times \frac{\text{V}}{\text{m}} = \text{A}/\text{m}^2

  2. Step 2

    tan⁡θ=ExEy=120−160=−0.75\tan \theta = \frac{E_x}{E_y} = \frac{120}{-160} = -0.75

    Correct

    tan⁡θ=EyEx=−160120=−43≈−1.333\tan \theta = \frac{E_y}{E_x} = \frac{-160}{120} = -\frac{4}{3} \approx -1.333

    You inverted the components in the tangent definition. For an angle θ\theta measured from the positive xx-axis, tangent is defined as the vertical component over the horizontal component, tan⁡θ=oppositeadjacent=EyEx\tan \theta = \frac{\text{opposite}}{\text{adjacent}} = \frac{E_y}{E_x}.

  3. Step 3

    arctan⁡(−0.75)=−36.87∘\arctan(-0.75) = -36.87^\circ

    Correct

    arctan⁡(−43)≈−53.13∘\arctan\left(-\frac{4}{3}\right) \approx -53.13^\circ

    You evaluated the inverse tangent correctly for your value, but the input was derived from the inverted component ratio.

  4. Step 4

    θ=360∘−36.87∘=323.13∘\theta = 360^\circ - 36.87^\circ = 323.13^\circ

    Correct

    θ=360∘−53.13∘=306.87∘≈307∘\theta = 360^\circ - 53.13^\circ = 306.87^\circ \approx 307^\circ

    You correctly added 360∘360^\circ to adjust a fourth-quadrant angle into the range [0∘,360∘)[0^\circ, 360^\circ), but the final numerical value carries forward the earlier ratio error.](streamdown:incomplete-link)

WHAT YOU DID WELL
Compliments from Your Teacher

You correctly performed dimensional analysis to confirm that [σE]=A/m2[\sigma E] = \text{A}/\text{m}^2.

You correctly recognized that the vector lies in Quadrant IV and properly adjusted the negative reference angle by adding 360∘360^\circ.

THE ERROR
Where Your ACEpath Teacher Spotted the Mistake
Inverted vector component ratio in trigonometric function

no

WHY IT HAPPENED
ACEpath Teacher's Diagnosis

You confused the orientation of the right triangle relative to the coordinate axes, placing the adjacent side along the yy-axis rather than the xx-axis, which led to setting tan⁡θ=Ex/Ey\tan\theta = E_x / E_y instead of tan⁡θ=Ey/Ex\tan\theta = E_y / E_x.

REASONING PATH
Your ACEpath teacher’s suggested approach
Standard Angle Definition
  • For any 2D vector V⃗=Vxi^+Vyj^\vec{V} = V_x\hat{i} + V_y\hat{j}, the counterclockwise angle θ\theta measured from the positive xx-axis satisfies tan⁡θ=VyVx=riserun\tan \theta = \frac{V_y}{V_x} = \frac{\text{rise}}{\text{run}}.

  • Always sketch the vector on Cartesian axes and remember tan⁡θ=yx\tan\theta = \frac{y}{x}.

Quadrant & Angle Conversion
  • When Vx>0V_x > 0 and Vy<0V_y < 0, the vector lies in Quadrant IV, so the standard angle in [0∘,360∘)[0^\circ, 360^\circ) is θ=360∘−∣ϕ∣\theta = 360^\circ - |\phi|, where ϕ=arctan⁡(∣Vy∣Vx)\phi = \arctan\left(\frac{|V_y|}{V_x}\right).](streamdown:incomplete-link)

  • Check your angle visually: since ∣Ey∣=160>Ex=120|E_y| = 160 > E_x = 120, the vector must be steeper than 45∘45^\circ away from the positive xx-axis.

CORRECTED PATH
ACEpath Teacher's Demonstration
  1. Set up the correct tangent ratio using tan⁡θ=EyEx=−160120=−43\tan \theta = \frac{E_y}{E_x} = \frac{-160}{120} = -\frac{4}{3}.

  2. Find the reference angle below the positive xx-axis: ϕ=arctan⁡(43)≈53.13∘\phi = \arctan\left(\frac{4}{3}\right) \approx 53.13^\circ.

  3. Compute the counterclockwise angle in the range [0∘,360∘)[0^\circ, 360^\circ): θ=360∘−53.13∘=306.87∘≈307∘\theta = 360^\circ - 53.13^\circ = 306.87^\circ \approx 307^\circ.](streamdown:incomplete-link)

Final answer

(a) A/m2\text{A}/\text{m}^2; (b) θ≈307∘\theta \approx 307^\circ

NEXT STEPS
Final Takeaways from Your Teacher
  • Sketch the vector components on an xyxy-plane whenever finding vector directions to verify that the opposite side is along the yy-direction.

  • Remember the mnemonic: slope and tangent are both ΔyΔx=yx\frac{\Delta y}{\Delta x} = \frac{y}{x}.

Lock it in

Similar question

01

A uniform electric field is given by E⃗=(50 i^−503 j^) V/m\vec{E} = (50\,\hat{i} - 50\sqrt{3}\,\hat{j})\text{ V/m}. Find the counterclockwise angle θ\theta that E⃗\vec{E} makes with the positive xx-axis in the range [0∘,360∘)[0^\circ, 360^\circ).](streamdown:incomplete-link)

Answer

θ=300∘\theta = 300^\circ. The vector lies in Quadrant IV because Ex>0E_x > 0 and Ey<0E_y < 0. The reference angle is ϕ=arctan⁡(503/50)=60∘\phi = \arctan(50\sqrt{3}/50) = 60^\circ. Measuring counterclockwise from +x+x, θ=360∘−60∘=300∘\theta = 360^\circ - 60^\circ = 300^\circ.

02

An electron drifts with velocity v⃗d=(−40 i^+30 j^) mm/s\vec{v}_d = (-40\,\hat{i} + 30\,\hat{j})\text{ mm/s}. Find the direction angle θ\theta of v⃗d\vec{v}_d measured counterclockwise from the positive xx-axis in the range [0∘,360∘)[0^\circ, 360^\circ).](streamdown:incomplete-link)

Answer

θ=143.1∘\theta = 143.1^\circ. The vector lies in Quadrant II because vx<0v_x < 0 and vy>0v_y > 0. The reference angle is ϕ=arctan⁡(30/40)≈36.87∘\phi = \arctan(30/40) \approx 36.87^\circ. Measuring counterclockwise from +x+x, θ=180∘−36.87∘=143.13∘≈143.1∘\theta = 180^\circ - 36.87^\circ = 143.13^\circ \approx 143.1^\circ.

03

A current density vector is J⃗=(−2.0 i^−2.0 j^)×105 A/m2\vec{J} = (-2.0\,\hat{i} - 2.0\,\hat{j})\times 10^5\text{ A/m}^2. (a) State the quadrant of J⃗\vec{J}. (b) Calculate its angle θ\theta in the range [0∘,360∘)[0^\circ, 360^\circ).](streamdown:incomplete-link)

Answer

(a) Quadrant III (both components are negative). (b) θ=225∘\theta = 225^\circ. The reference angle is arctan⁡(∣−2.0∣/∣−2.0∣)=45∘\arctan(|-2.0|/|-2.0|) = 45^\circ. In Quadrant III, θ=180∘+45∘=225∘\theta = 180^\circ + 45^\circ = 225^\circ.

Loading workspace…