Resources

A crate of mass m=25.0 kgm = 25.0\text{ kg} rests on a rough horizontal warehouse floor where the coefficient of kinetic friction is μk=0.280\mu_k = 0.280. A worker pulls the crate across the floor using a rope that exerts a constant tension force T=115 NT = 115\text{ N} directed at an angle θ=25.0∘\theta = 25.0^\circ above the horizontal. Define a standard Cartesian coordinate system with +x+x pointing horizontally in the direction of motion (to the right) and +y+y pointing vertically upward. Take the acceleration due to gravity to be g=9.80 m/s2g = 9.80\text{ m/s}^2. (a) Identify and write the vector component expressions for all external forces acting on the crate. (b) Calculate the magnitude of the normal force FNF_N exerted by the floor on the crate. (c) Determine the magnitude of the kinetic friction force fkf_k.

Answer and steps

Final answer

(a) F⃗g=−mgj^=−245j^ N\vec{F}_g = -mg\hat{j} = -245\hat{j}\text{ N}, F⃗N=FNj^\vec{F}_N = F_N\hat{j}, T⃗=(Tcos⁡θ)i^+(Tsin⁡θ)j^=104i^+48.6j^ N\vec{T} = (T\cos\theta)\hat{i} + (T\sin\theta)\hat{j} = 104\hat{i} + 48.6\hat{j}\text{ N}, f⃗k=−fki^\vec{f}_k = -f_k\hat{i}; (b) FN=mg−Tsin⁡θ=196 NF_N = mg - T\sin\theta = 196\text{ N}; (c) fk=μkFN=55.0 Nf_k = \mu_k F_N = 55.0\text{ N}.

Steps

Part (a): Vector Component Expressions for All External Forces

Identify each external force acting on the crate and resolve it along the standard coordinate axes where +x+x is directed to the right (direction of motion) and +y+y is directed upward:

  1. Gravitational Force (F⃗g\vec{F}_g): Acts vertically downward toward the center of the Earth: F⃗g=−mg j^=−(25.0 kg)(9.80 m/s2) j^=−245 j^ N\vec{F}_g = -mg\,\hat{j} = -(25.0\text{ kg})(9.80\text{ m/s}^2)\,\hat{j} = -245\,\hat{j}\text{ N}
  2. Normal Force (F⃗N\vec{F}_N): Exerted perpendicularly upward by the floor on the crate: F⃗N=FN j^\vec{F}_N = F_N\,\hat{j}
  3. Tension Force (T⃗\vec{T}): Pulls at an angle θ=25.0∘\theta = 25.0^\circ above the horizontal. Decomposing into horizontal and vertical components: Tx=Tcos⁡θ=115cos⁡(25.0∘)≈104 NT_x = T\cos\theta = 115\cos(25.0^\circ)\approx 104\text{ N} Ty=Tsin⁡θ=115sin⁡(25.0∘)≈48.6 NT_y = T\sin\theta = 115\sin(25.0^\circ)\approx 48.6\text{ N} In vector form: T⃗=(Tcos⁡θ) i^+(Tsin⁡θ) j^=104 i^+48.6 j^ N\vec{T} = (T\cos\theta)\,\hat{i} + (T\sin\theta)\,\hat{j} = 104\,\hat{i} + 48.6\,\hat{j}\text{ N}
  4. Kinetic Friction Force (f⃗k\vec{f}_k): Opposes the direction of horizontal sliding, acting to the left: f⃗k=−fk i^\vec{f}_k = -f_k\,\hat{i}

Part (b): Magnitude of the Normal Force

The crate remains in contact with the flat floor and does not accelerate vertically (ay=0a_y = 0). According to Newton's second law for the vertical axis:

∑Fy=may=0\sum F_y = m a_y = 0

Substitute the vertical components:

FN+Tsin⁡θ−mg=0F_N + T\sin\theta - mg = 0

Isolate FNF_N:

FN=mg−Tsin⁡θF_N = mg - T\sin\theta

Common Pitfall: Forgetting the upward vertical component of tension (Tsin⁡θT\sin\theta) often leads to assuming FN=mgF_N = mg. Because the rope pulls partially upward, it relieves some of the load pressing onto the floor, making FN<mgF_N < mg.

Substitute the numerical values:

FN=245 N−115sin⁡(25.0∘) N=245 N−48.6 N=196 NF_N = 245\text{ N} - 115\sin(25.0^\circ)\text{ N} = 245\text{ N} - 48.6\text{ N} = 196\text{ N}


Part (c): Magnitude of the Kinetic Friction Force

The magnitude of kinetic friction depends directly on the normal force through the relationship:

fk=μkFNf_k = \mu_k F_N

Substitute μk=0.280\mu_k = 0.280 and FN=196.4 NF_N = 196.4\text{ N}:

fk=(0.280)(196.4 N)≈55.0 Nf_k = (0.280)(196.4\text{ N}) \approx 55.0\text{ N}

Typical errors

OverviewACEpath Teacher's Diagnosis

01 The student assumes the normal force equals the crate's full weight, forgetting that the upward component of the tension reduces the normal force.

Sample Student Work

Reviewed by ACEpath Teacher
Step-by-Step Review
Walk Through It with Your Teacher
Partially correct
  1. Step 1

    T⃗=(115cos⁡(25.0∘),115sin⁡(25.0∘))=(104.2 N,48.6 N)  ⟹  F⃗g=(0,−25.0×9.80)=(0,−245 N)  ⟹  F⃗N=(0,FN)  ⟹  f⃗k=(−fk,0)\vec{T} = (115\cos(25.0^\circ), 115\sin(25.0^\circ)) = (104.2\text{ N}, 48.6\text{ N}) \implies \vec{F}_g = (0, -25.0 \times 9.80) = (0, -245\text{ N}) \implies \vec{F}_N = (0, F_N) \implies \vec{f}_k = (-f_k, 0)

  2. Step 2

    FN=m⋅g  ⟹  FN=25.0×9.80=245 NF_N = m \cdot g \implies F_N = 25.0 \times 9.80 = 245\text{ N}

    Correct

    ∑Fy=FN+Tsin⁡θ−mg=0  ⟹  FN=mg−Tsin⁡θ=245 N−48.6 N=196 N\sum F_y = F_N + T\sin\theta - mg = 0 \implies F_N = mg - T\sin\theta = 245\text{ N} - 48.6\text{ N} = 196\text{ N}

    You set FN=mgF_N = mg, which assumes the vertical forces only consist of the normal force and gravity. Because the tension force pulls partially upward (Ty=48.6 NT_y = 48.6\text{ N}), the vertical equilibrium equation is FN+Ty−mg=0F_N + T_y - mg = 0, giving FN=196 NF_N = 196\text{ N}.

  3. Step 3

    fk=μk⋅FN  ⟹  fk=0.280×245=68.6 Nf_k = \mu_k \cdot F_N \implies f_k = 0.280 \times 245 = 68.6\text{ N}

    Correct

    fk=μkFN=0.280×196.4 N=55.0 Nf_k = \mu_k F_N = 0.280 \times 196.4\text{ N} = 55.0\text{ N}

    You correctly applied the friction formula fk=μkFNf_k = \mu_k F_N, but the resulting value was thrown off by the incorrect normal force from the previous step.

WHAT YOU DID WELL
Compliments from Your Teacher

You correctly decomposed the tension force into its trigonometric components.

You accurately identified the orientation and sign of all four external forces in part (a).

You correctly applied the relationship fk=μkFNf_k = \mu_k F_N for kinetic friction.

THE ERROR
Where Your ACEpath Teacher Spotted the Mistake
Missing force component in equilibrium condition

no

WHY IT HAPPENED
ACEpath Teacher's Diagnosis

You relied on the memorized rule FN=mgF_N = mg instead of applying Newton's second law along the vertical axis (∑Fy=0\sum F_y = 0) to account for all vertical force components acting on the body.

REASONING PATH
Your ACEpath teacher’s suggested approach
Vertical Equilibrium Condition
  • When there is no vertical acceleration, set the algebraic sum of all vertical forces to zero: ∑Fy=may=0\sum F_y = m a_y = 0.

  • List every upward force on one side and every downward force on the other: FN+Ty=mgF_N + T_y = mg.

Normal Force Dependence
  • The normal force adjusts depending on other vertical loads; it only equals mgmg on a flat surface when no other vertical forces are present.

  • Always solve for FNF_N algebraically from ∑Fy=0\sum F_y = 0 before substituting numerical values.

CORRECTED PATH
ACEpath Teacher's Demonstration
  1. Write Newton's second law for the vertical axis: ∑Fy=FN+Tsin⁡(25.0∘)−mg=0\sum F_y = F_N + T\sin(25.0^\circ) - mg = 0.

  2. Solve for the normal force: FN=mg−Tsin⁡(25.0∘)=245 N−48.6 N=196.4 N≈196 NF_N = mg - T\sin(25.0^\circ) = 245\text{ N} - 48.6\text{ N} = 196.4\text{ N} \approx 196\text{ N}.

  3. Substitute the corrected FNF_N into the kinetic friction formula: fk=μkFN=0.280×196.4 N≈55.0 Nf_k = \mu_k F_N = 0.280 \times 196.4\text{ N} \approx 55.0\text{ N}.

Final answer

(b) FN=196 NF_N = 196\text{ N}; (c) fk=55.0 Nf_k = 55.0\text{ N}

NEXT STEPS
Final Takeaways from Your Teacher
  • Always write out ∑Fy=0\sum F_y = 0 explicitly from your free-body diagram before evaluating FNF_N.

  • Practice checking whether any applied force has a vertical component that lifts or presses down on the object.

OverviewACEpath Teacher's Diagnosis

02 The student adds the vertical component of tension to the weight instead of subtracting it, mistakenly treating the upward pull as an additional downward load.

Sample Student Work

Reviewed by ACEpath Teacher
Step-by-Step Review
Walk Through It with Your Teacher
Partially correct
  1. Step 1

    T⃗=(115cos⁡(25.0∘),115sin⁡(25.0∘))=(104.2 N,48.6 N)\vec{T} = (115\cos(25.0^\circ), 115\sin(25.0^\circ)) = (104.2\text{ N}, 48.6\text{ N})   ⟹  \implies F⃗g=(0,−25.0×9.80)=(0,−245 N)\vec{F}_g = (0, -25.0 \times 9.80) = (0, -245\text{ N})   ⟹  \implies F⃗N=(0,FN)\vec{F}_N = (0, F_N)   ⟹  \implies f⃗k=(−fk,0)\vec{f}_k = (-f_k, 0)

  2. Step 2

    FN=m⋅g+Tsin⁡(θ)  ⟹  FN=245+115sin⁡(25.0∘)=245+48.6=293.6 NF_N = m \cdot g + T\sin(\theta) \implies F_N = 245 + 115\sin(25.0^\circ) = 245 + 48.6 = 293.6\text{ N}

    Correct

    ∑Fy=FN+Tsin⁡θ−mg=0  ⟹  FN=mg−Tsin⁡θ=245−48.6=196 N\sum F_y = F_N + T\sin\theta - mg = 0 \implies F_N = mg - T\sin\theta = 245 - 48.6 = 196\text{ N}

    Because the rope pulls upward with component Tsin⁡θT\sin\theta, it relieves some of the load pressing against the floor. Setting the net vertical force to zero gives FN+Tsin⁡θ−mg=0F_N + T\sin\theta - mg = 0, so FN=mg−Tsin⁡θF_N = mg - T\sin\theta, not mg+Tsin⁡θmg + T\sin\theta.

  3. Step 3

    fk=μk⋅FN  ⟹  fk=0.280×293.6=82.2 Nf_k = \mu_k \cdot F_N \implies f_k = 0.280 \times 293.6 = 82.2\text{ N}

    Correct

    fk=μkFN=(0.280)(196.4 N)≈55.0 Nf_k = \mu_k F_N = (0.280)(196.4\text{ N}) \approx 55.0\text{ N}

    Your friction formula is correct, but your answer is numerically affected by the incorrect value of FNF_N from part (b).

WHAT YOU DID WELL
Compliments from Your Teacher

You correctly resolved the tension vector into horizontal and vertical components.

You properly set up the coordinate representations for gravity, normal force, and friction.

You correctly applied the kinetic friction formula fk=μkFNf_k = \mu_k F_N.

THE ERROR
Where Your ACEpath Teacher Spotted the Mistake
Normal force vertical equilibrium sign error

You treated the upward pull of tension as an additional downward load pressing the crate into the floor.

WHY IT HAPPENED
ACEpath Teacher's Diagnosis

Misinterpreting the direction of the vertical component in Newton's second law ∑Fy=0\sum F_y = 0, leading to adding Tsin⁡θT\sin\theta to mgmg rather than subtracting it from mgmg.

REASONING PATH
Your ACEpath teacher’s suggested approach
Equilibrium Equation Setup
  • For a mass resting on a horizontal surface without vertical acceleration, the sum of upward forces must equal the sum of downward forces: ∑Fup=∑Fdown\sum F_{\text{up}} = \sum F_{\text{down}}.

  • Always list all upward forces (FN+Tsin⁡θF_N + T\sin\theta) on one side and downward forces (mgmg) on the other before isolating FNF_N.

Physical Reality Check
  • An upward pull always reduces contact pressure with the floor, so FN<mgF_N < mg.

  • Check whether your calculated normal force is less than the object's weight (245 N245\text{ N}) when pulled upward.

CORRECTED PATH
ACEpath Teacher's Demonstration
  1. Set up vertical equilibrium: FN+Tsin⁡θ−mg=0F_N + T\sin\theta - mg = 0

  2. Isolate FNF_N: FN=mg−Tsin⁡θ=245 N−48.6 N=196.4 NF_N = mg - T\sin\theta = 245\text{ N} - 48.6\text{ N} = 196.4\text{ N}

  3. Calculate kinetic friction: fk=μkFN=0.280×196.4 N≈55.0 Nf_k = \mu_k F_N = 0.280 \times 196.4\text{ N} \approx 55.0\text{ N}

Final answer

(b) FN=196 NF_N = 196\text{ N}; (c) fk=55.0 Nf_k = 55.0\text{ N}

NEXT STEPS
Final Takeaways from Your Teacher
  • Practice writing the explicit equilibrium condition ∑Fy=0\sum F_y = 0 before rearranging for the normal force.

  • Always perform a physical sanity check: pulling upward must make FN<mgF_N < mg, while pushing downward makes FN>mgF_N > mg.

OverviewACEpath Teacher's Diagnosis

03 The student swaps the sine and cosine trigonometric functions for the force components, using cosine for the vertical component of tension.

Sample Student Work

Reviewed by ACEpath Teacher
Step-by-Step Review
Walk Through It with Your Teacher
Incorrect
  1. Step 1

    T⃗=(115sin⁡(25.0∘),115cos⁡(25.0∘))=(48.6 N,104.2 N)\vec{T} = (115\sin(25.0^\circ), 115\cos(25.0^\circ)) = (48.6\text{ N}, 104.2\text{ N}), F⃗g=(0,−245 N)\vec{F}_g = (0, -245\text{ N}), F⃗N=(0,FN)\vec{F}_N = (0, F_N), f⃗k=(−fk,0)\vec{f}_k = (-f_k, 0)

    Correct

    T⃗=(115cos⁡(25.0∘),115sin⁡(25.0∘))≈(104 N,48.6 N)\vec{T} = (115\cos(25.0^\circ), 115\sin(25.0^\circ)) \approx (104\text{ N}, 48.6\text{ N}), F⃗g=(0,−245 N)\vec{F}_g = (0, -245\text{ N}), F⃗N=(0,FN)\vec{F}_N = (0, F_N), f⃗k=(−fk,0)\vec{f}_k = (-f_k, 0)

    Because the angle θ=25.0∘\theta = 25.0^\circ is measured above the horizontal, the adjacent side along the xx-axis is Tx=Tcos⁡θT_x = T\cos\theta, while the opposite side along the yy-axis is Ty=Tsin⁡θT_y = T\sin\theta. You reversed these two trigonometric functions.

  2. Step 2

    FN=m⋅g−Ty=245−115cos⁡(25.0∘)=245−104.2=140.8 NF_N = m \cdot g - T_y = 245 - 115\cos(25.0^\circ) = 245 - 104.2 = 140.8\text{ N}

    Correct

    FN=mg−Tsin⁡(25.0∘)=245 N−48.6 N≈196 NF_N = mg - T\sin(25.0^\circ) = 245\text{ N} - 48.6\text{ N} \approx 196\text{ N}

    Your equilibrium equation FN=mg−TyF_N = mg - T_y is set up correctly, but substituting the swapped value Ty=104.2 NT_y = 104.2\text{ N} instead of 48.6 N48.6\text{ N} led to an incorrect normal force.

  3. Step 3

    fk=μkFN=0.280×140.8=39.4 Nf_k = \mu_k F_N = 0.280 \times 140.8 = 39.4\text{ N}

    Correct

    fk=μkFN=0.280×196.4 N≈55.0 Nf_k = \mu_k F_N = 0.280 \times 196.4\text{ N} \approx 55.0\text{ N}

    Your formula fk=μkFNf_k = \mu_k F_N is correct, but the result was affected by the incorrect value of FNF_N from the previous step.

WHAT YOU DID WELL
Compliments from Your Teacher

You correctly represented gravity, the normal force, and friction in Cartesian vector form.

You correctly applied vertical equilibrium ∑Fy=0\sum F_y = 0 to express FN=mg−TyF_N = mg - T_y.

You correctly used the kinetic friction model fk=μkFNf_k = \mu_k F_N.

THE ERROR
Where Your ACEpath Teacher Spotted the Mistake
Trigonometric Component Swap

You accidentally assigned sine to the xx-component and cosine to the yy-component for an angle measured from the horizontal.

WHY IT HAPPENED
ACEpath Teacher's Diagnosis

Confusing which trigonometric ratio corresponds to the adjacent versus opposite side of the reference triangle when decomposing an off-axis force vector.

REASONING PATH
Your ACEpath teacher’s suggested approach
Reference Angle Orientation
  • When an angle θ\theta is measured relative to the horizontal (xx-axis), the horizontal leg is adjacent (Tx=Tcos⁡θT_x = T\cos\theta) and the vertical leg is opposite (Ty=Tsin⁡θT_y = T\sin\theta).

  • Always sketch a right triangle with the force vector as the hypotenuse, label θ\theta, and check whether the component is adjacent (cosine) or opposite (sine) to that angle.

CORRECTED PATH
ACEpath Teacher's Demonstration
  1. Resolve tension: Tx=115cos⁡(25.0∘)≈104.2 NT_x = 115\cos(25.0^\circ) \approx 104.2\text{ N} and Ty=115sin⁡(25.0∘)≈48.60 NT_y = 115\sin(25.0^\circ) \approx 48.60\text{ N}.

  2. Compute the normal force from ∑Fy=0\sum F_y = 0: FN=mg−Ty=245 N−48.60 N=196.4 N≈196 NF_N = mg - T_y = 245\text{ N} - 48.60\text{ N} = 196.4\text{ N} \approx 196\text{ N}.

  3. Compute kinetic friction: fk=μkFN=0.280×196.4 N≈55.0 Nf_k = \mu_k F_N = 0.280 \times 196.4\text{ N} \approx 55.0\text{ N}.

Final answer

(a) T⃗=104i^+48.6j^ N\vec{T} = 104\hat{i} + 48.6\hat{j}\text{ N}, F⃗g=−245j^ N\vec{F}_g = -245\hat{j}\text{ N}, F⃗N=196j^ N\vec{F}_N = 196\hat{j}\text{ N}, f⃗k=−55.0i^ N\vec{f}_k = -55.0\hat{i}\text{ N}; (b) FN=196 NF_N = 196\text{ N}; (c) fk=55.0 Nf_k = 55.0\text{ N}

NEXT STEPS
Final Takeaways from Your Teacher
  • Draw the right triangle formed by the vector components before writing algebraic formulas.

  • Use the mnemonic SOH-CAH-TOA to explicitly confirm whether each axis corresponds to the opposite or adjacent side of the given angle.

Lock it in

Similar question

01

A 40.0 kg40.0\text{ kg} sled is pulled horizontally across flat snow with a rope exerting a force of 120 N120\text{ N} at an angle of 30.0∘30.0^\circ above the horizontal. If g=9.80 m/s2g = 9.80\text{ m/s}^2 and μk=0.150\mu_k = 0.150, determine the magnitude of the normal force FNF_N and the kinetic friction force fkf_k.

Answer

FN=332 NF_N = 332\text{ N}, fk=49.8 Nf_k = 49.8\text{ N}. Vertical equilibrium gives FN+120sin⁡(30.0∘)−(40.0)(9.80)=0  ⟹  FN=392−60.0=332 NF_N + 120\sin(30.0^\circ) - (40.0)(9.80) = 0 \implies F_N = 392 - 60.0 = 332\text{ N}. Then fk=μkFN=0.150×332 N=49.8 Nf_k = \mu_k F_N = 0.150 \times 332\text{ N} = 49.8\text{ N}.

02

A gardener pushes a 15.0 kg15.0\text{ kg} lawnmower across flat ground with an applied force of 80.0 N80.0\text{ N} directed along the handle at an angle of 37.0∘37.0^\circ below the horizontal. Taking g=9.80 m/s2g = 9.80\text{ m/s}^2, find the normal force FNF_N exerted by the lawn on the mower.

Answer

FN=195 NF_N = 195\text{ N}. Because the force pushes downward, the vertical component adds to gravity: ∑Fy=FN−mg−Fsin⁡(37.0∘)=0  ⟹  FN=(15.0)(9.80)+80.0sin⁡(37.0∘)=147+48.1=195.1 N≈195 N\sum F_y = F_N - mg - F\sin(37.0^\circ) = 0 \implies F_N = (15.0)(9.80) + 80.0\sin(37.0^\circ) = 147 + 48.1 = 195.1\text{ N} \approx 195\text{ N}.

03

A block of mass m=8.00 kgm = 8.00\text{ kg} on a horizontal surface is subjected to a pulling force TT directed at θ=30.0∘\theta = 30.0^\circ above the horizontal. The coefficient of static friction is μs=0.450\mu_s = 0.450. What minimum tension TT is required to start moving the block horizontally? (g=9.80 m/s2g = 9.80\text{ m/s}^2).

Answer

T=32.5 NT = 32.5\text{ N}. Set horizontal force equal to maximum static friction: Tcos⁡θ=fs,max=μsFNT\cos\theta = f_{s,\text{max}} = \mu_s F_N. From vertical equilibrium, FN=mg−Tsin⁡θF_N = mg - T\sin\theta. Substituting gives Tcos⁡θ=μs(mg−Tsin⁡θ)  ⟹  T(cos⁡θ+μssin⁡θ)=μsmgT\cos\theta = \mu_s(mg - T\sin\theta) \implies T(\cos\theta + \mu_s\sin\theta) = \mu_s mg. Thus T=0.450×8.00×9.80cos⁡(30∘)+0.450sin⁡(30∘)=35.280.8660+0.2250=35.281.091≈32.5 NT = \frac{0.450 \times 8.00 \times 9.80}{\cos(30^\circ) + 0.450\sin(30^\circ)} = \frac{35.28}{0.8660 + 0.2250} = \frac{35.28}{1.091} \approx 32.5\text{ N}.

Loading workspace…