Resources
A crate of mass is initially at rest on a horizontal concrete surface with a coefficient of static friction and a coefficient of kinetic friction . An applied horizontal force acts on the crate. Taking : (a) Calculate the magnitude of the frictional force when . (b) Calculate the magnitude of the frictional force when . (c) Calculate the magnitude of the frictional force immediately after is increased to .
Answer and steps
Final answer
(a) ; (b) ; (c) (the crate slips because , causing the frictional force to drop discontinuously to ).
Steps
Determine the Normal Force and Friction Thresholds
The crate rests on a flat horizontal surface with no vertical motion, so the upward normal force balances the downward gravitational force:
Static friction opposes the tendency of motion and can adjust up to a maximum threshold, :
Once the crate overcomes this threshold and begins to slide, the friction transitions to kinetic friction, :
Part (a): Applied Force
- Compare the applied horizontal force to the maximum static friction:
- Because the applied force does not exceed , the crate remains stationary.
- By Newton's first law, the net horizontal force must be zero, so static friction exactly balances the applied force:
Common Pitfall: Do not use automatically for static friction. The formula gives only the maximum possible static friction. As long as the object does not move, .
Part (b): Applied Force
- Comparing the applied force to the threshold:
- The crate still does not move. Static friction increases to match the applied pull:
Part (c): Applied Force
- Comparing the applied force to the static threshold:
- The applied force exceeds the maximum static friction threshold, breaking the static hold and causing the crate to accelerate.
- The friction immediately switches from static to kinetic:
Typical errors
01 The student mistakenly assumes static friction is always equal to its maximum value (μs N) whenever the object is at rest, rather than matching the applied force.
Sample Student Work
Reviewed by ACEpath TeacherStep-by-Step Review
Walk Through It with Your Teacher- Step 1Correct
. Since , the crate remains at rest, so .
You correctly determined the normal force and computed . However, represents the maximum possible static friction (), not the actual static friction for any applied force. Because , the crate does not move, and static friction only needs to balance the applied pull: .
- Step 2Correct
Because , the crate stays at rest, which means static friction balances the applied force: .
You correctly noted that means the crate is at rest. But when an object remains at rest, Newton's first law requires the horizontal net force to be zero: . Therefore, static friction adjusts to exactly match the applied pull () rather than jumping directly to .
- Step 3
WHAT YOU DID WELL
Compliments from Your TeacherYou correctly calculated the vertical normal force .
You correctly evaluated the threshold for impending motion, .
You correctly identified that overcomes static friction and successfully computed the kinetic friction .
THE ERROR
Where Your ACEpath Teacher Spotted the Mistakeno
WHY IT HAPPENED
ACEpath Teacher's DiagnosisYou treated the formula as an equality for static friction at all times, rather than an inequality . When an object remains at rest, static friction is a self-adjusting reaction force whose magnitude is determined by Newton's first law (), reaching only at the verge of slipping.
REASONING PATH
Your ACEpath teacher’s suggested approach- Static Friction Inequality
Static friction satisfies .
Never assume unless the problem explicitly states the object is on the verge of slipping or experiencing maximum static friction.
- Equilibrium Condition
If , the object does not accelerate ().
Set the static friction equal to the net opposing applied force: .
CORRECTED PATH
ACEpath Teacher's DemonstrationIdentify the maximum static friction threshold: .
For part (a), compare to . Since , the crate does not move, so by horizontal equilibrium .
For part (b), compare to . Since , the crate remains stationary, so .
For part (c), compare to . Since , the crate accelerates, switching friction to kinetic: .
(a) ; (b) ; (c)
02 The student uses the kinetic friction coefficient across all parts under the false assumption that friction is always calculated using fk = μk N.
Sample Student Work
Reviewed by ACEpath TeacherStep-by-Step Review
Walk Through It with Your Teacher- Step 1
- Step 2Correct
. Since , the crate does not move, so .
Because the crate starts at rest, you must compare the applied force to the maximum static friction . Since , static friction matches the applied force exactly.
- Step 3Correct
Since , the crate remains at rest, so .
The applied pull of still does not exceed , so the crate remains stationary and static friction adjusts to .
- Step 4
WHAT YOU DID WELL
Compliments from Your TeacherYou correctly found the normal force acting on the horizontal surface using .
You used the correct value for the coefficient of kinetic friction when computing sliding friction.
THE ERROR
Where Your ACEpath Teacher Spotted the MistakeYou applied the kinetic friction formula immediately without checking if the crate was actually moving.
WHY IT HAPPENED
ACEpath Teacher's DiagnosisYou assumed that friction is always computed using , overlooking that an object initially at rest experiences static friction () that self-adjusts to balance the applied force until .
REASONING PATH
Your ACEpath teacher’s suggested approach- Static vs. Kinetic State Check
For an object initially at rest, calculate the static threshold before choosing a friction formula.
Compare with . If , the object remains stationary and .
- Kinetic Friction Trigger
Kinetic friction applies only when there is relative sliding between surfaces ().
Use only after verifying that the maximum static hold has been broken.
CORRECTED PATH
ACEpath Teacher's DemonstrationCompute maximum static friction: .
For part (a), compare to : since , the crate does not move, so .
For part (b), compare to : since , the crate remains at rest, so .
For part (c), compare to : since , the crate slips and friction becomes kinetic: .
(a) ; (b) ; (c)
03 The student uses the static friction coefficient even after the object starts moving in part (c), continuing to report maximum static friction instead of switching to kinetic friction.
Sample Student Work
Reviewed by ACEpath TeacherStep-by-Step Review
Walk Through It with Your Teacher- Step 1
- Step 2
- Step 3
- Step 4Correct
While you correctly noted that the crate starts moving because , once relative sliding begins, the friction is kinetic () rather than static friction ().
WHAT YOU DID WELL
Compliments from Your TeacherYou correctly calculated the normal force as .
You correctly calculated the maximum static friction limit .
You correctly applied the condition of static equilibrium to find when the crate is stationary in parts (a) and (b).
You correctly observed that an applied force of causes the crate to move.
THE ERROR
Where Your ACEpath Teacher Spotted the MistakeYou recognized that the crate moves, but you reused instead of switching to .
WHY IT HAPPENED
ACEpath Teacher's DiagnosisConfusing maximum static friction with kinetic friction. Static friction applies only when there is no relative motion between contact surfaces. Once the applied force overcomes , sliding occurs, and the resisting force immediately drops to kinetic friction, given by .
REASONING PATH
Your ACEpath teacher’s suggested approach- Check Motion State
If , the object slips and undergoes kinetic friction.
Always switch to the kinetic friction formula as soon as the threshold is exceeded.
CORRECTED PATH
ACEpath Teacher's DemonstrationCompare the applied force to the static threshold: , so the crate accelerates and begins sliding.
Apply the kinetic friction equation for sliding surfaces: .
Substitute the given values: .
(a) ; (b) ; (c)
Lock it in
What does the formula represent for an object resting on a surface?
It represents the maximum possible static friction (), not the actual static friction at every moment.
Similar question
A wooden chest sits on a horizontal floor where and . Taking , find the frictional force acting on the chest when a horizontal pull of is applied.
Answer
.
- Calculate normal force: .
- Calculate threshold: .
- Since , the chest remains stationary and static friction matches the pull: .
A horizontal pulling force on a trunk is gradually increased from . The coefficients of friction are and (). (a) What minimum force is required to start the trunk moving? (b) What is the friction force when the pull is ? (c) What is the friction force when the pull reaches ?
Answer
(a) ; (b) ; (c) .
- .
- , which is the threshold to initiate motion.
- At , the trunk stays at rest, so .
- At , the trunk slides, so kinetic friction acts: .
A block is at rest on a horizontal surface (, , ). A person pulls on the block with an applied force directed at an angle above the horizontal. Determine whether the block moves and find the magnitude of the frictional force.
Answer
The block remains at rest; .
- Vertical equilibrium: .
- Maximum static friction: ... Wait, check horizontal component: .
- Compare , so the block slips and accelerates!
- Kinetic friction: .