Resources
An electron with charge and mass enters a uniform magnetic field region of length along the positive -axis. The magnetic field has magnitude directed along the positive -axis. If the electron enters with an initial speed of along the -direction, calculate the angular deflection (in degrees) of the electron's trajectory as it exits the magnetic field region.
Answer and steps
Final answer
Steps
Determine the Direction of the Magnetic Force
When a charged particle moves through a magnetic field, it experiences the Lorentz magnetic force:
- The electron moves along the positive -axis: .
- The magnetic field points along the positive -axis: .
- Using the right-hand rule, the cross product is .
- Because the electron carries a negative charge (), the force direction is reversed:
Thus, the force acts entirely in the -direction, causing the electron to deflect upward along a circular arc in the -plane.
Calculate the Orbital Radius of Curvature
The magnetic force provides the necessary centripetal force for uniform circular motion:
Substitute the given numerical values:
The corresponding diameter of curvature is:
Calculate the Angular Deflection
As the electron traverses the field of span , the angular deflection of the trajectory chord relative to the entrance axis is given by the geometric chord relation:
Substitute and :
Taking the inverse sine:
Common Pitfall to Avoid
Do not forget the negative sign of the electron's charge when applying the right-hand rule. While the cross product points in the -direction, multiplying by the negative charge flips the deflection into the -direction.
Typical errors
01 The student confuses the circular trajectory relation sin θ = L / r with tan θ = L / r, which incorrectly assumes L corresponds to the adjacent side of the right triangle rather than the opposite side across the circular arc.
Sample Student Work
Reviewed by ACEpath TeacherStep-by-Step Review
Walk Through It with Your Teacher- Step 1
- Step 2Correct
In the geometry of circular deflection, the horizontal span is the side opposite to the deflection angle at the center of curvature, while the radius is the hypotenuse from the center of curvature to the exit point on the circle. Therefore, the ratio corresponds to , not .
- Step 3Correct
This step correctly evaluated the inverse trigonometric function of your previous ratio, but it inherited the error from using tangent instead of sine.
WHAT YOU DID WELL
Compliments from Your TeacherYou correctly recalled the formula for the radius of curvature of a charged particle in a uniform magnetic field.
You substituted the correct numerical values with consistent SI units to find .
THE ERROR
Where Your ACEpath Teacher Spotted the MistakeYou set instead of .
WHY IT HAPPENED
ACEpath Teacher's DiagnosisYou treated the radius as the adjacent leg of a right triangle rather than the hypotenuse extending from the center of curvature to the particle's exit point on the circular arc.
REASONING PATH
Your ACEpath teacher’s suggested approach- Identify the Center of Curvature
For a circular arc, the line segment from the center of curvature to any point on the trajectory has length and serves as the hypotenuse of the reference triangle.
Sketch the center of curvature perpendicular to the initial velocity, and draw the radius vector to the field boundary exit point.
- Set Up the Trigonometric Ratio
The horizontal width traversed is , so the angular deflection satisfies .
Use whenever a particle exits across a planar boundary at perpendicular distance .
CORRECTED PATH
ACEpath Teacher's DemonstrationSet up the sine relation from the right triangle formed by the center of curvature and the exit position: .
Substitute and : .
Compute the inverse sine: .
02 The student misremembers the cyclotron radius formula as r = qB / (mv), inverting the ratio of momentum to magnetic force factors.
Sample Student Work
Reviewed by ACEpath TeacherStep-by-Step Review
Walk Through It with Your Teacher- Step 1Correct
You inverted the formula for the radius of circular motion in a magnetic field. Balancing the centripetal force with the magnetic force gives , which yields .
- Step 2Correct
This step inherited the incorrect radius from Step 1.
- Step 3Correct
Your calculation evaluated correctly from your previous value, but the final angle is incorrect due to the inverted radius.
WHAT YOU DID WELL
Compliments from Your TeacherYou correctly identified that the magnetic force causes circular deflection.
You substituted the correct numerical constants and given quantities into your calculation.
You correctly evaluated the inverse sine function to find the angle.
THE ERROR
Where Your ACEpath Teacher Spotted the MistakeYou wrote rather than .
WHY IT HAPPENED
ACEpath Teacher's DiagnosisYou relied on a memorized fraction without verifying units or re-deriving the balance of forces. Because magnetic force provides centripetal acceleration, requires momentum in the numerator and magnetic interaction factors in the denominator.
REASONING PATH
Your ACEpath teacher’s suggested approach- Centripetal force balance
Always set centripetal force equal to magnetic Lorentz force before solving for to avoid inverting the fraction.
- Dimensional sanity check
has units of meters (momentum / force-factor)
Notice that higher momentum should widen the circle (), while a stronger field should bend it tighter ().
CORRECTED PATH
ACEpath Teacher's DemonstrationSet centripetal force equal to the magnetic force: .
Solve for the orbital radius: .
Calculate the diameter: .
Find the sine of the deflection angle: .
Compute the angle: .
03 The student approximates the arc length along the path as the field length L and sets θ = L / r in radians, confusing the subtended angle with its small-angle arc approximation despite θ being relatively large.
Sample Student Work
Reviewed by ACEpath TeacherStep-by-Step Review
Walk Through It with Your Teacher- Step 1
- Step 2Correct
You assumed the horizontal span equals the circular arc length and used . However, is the chord projection of the deflection across the field boundary, which follows .
- Step 3Correct
You converted radians to degrees accurately, but the value was affected by the incorrect formula in the previous step.
WHAT YOU DID WELL
Compliments from Your TeacherYou correctly identified the formula for the radius of curvature of a charged particle in a magnetic field.
You accurately substituted the physical constants and given parameters into the cyclotron radius formula.
You performed the unit conversion from radians to degrees correctly.
THE ERROR
Where Your ACEpath Teacher Spotted the MistakeYou equated the linear length of the field directly to the circular arc length subtended by the trajectory.
WHY IT HAPPENED
ACEpath Teacher's DiagnosisYou used the small-angle or straight-line arc length formula rather than setting up the exact right-triangle geometry of the trajectory chord, where .
REASONING PATH
Your ACEpath teacher’s suggested approach- Trajectory Geometry
For a circular trajectory spanning a linear chord distance , the deflection angle satisfies .
Always sketch the circular arc and identify whether represents an arc length, a chord, or a coordinate projection before applying an angular formula.
CORRECTED PATH
ACEpath Teacher's DemonstrationUse the trajectory chord relation: .
Substitute and : .
Take the inverse sine to find the deflection angle: .
Lock it in
A charged particle enters a uniform magnetic field perpendicular to the boundary and exits after traversing a width . What trigonometric formula gives the angular deflection ?
, where . The radius is the hypotenuse from the center of curvature to the exit point.
Similar question
A proton (, ) enters a magnetic field region of width at a speed of . The magnetic field strength is perpendicular to the velocity. Calculate the angular deflection (in degrees) as the proton exits the field.
Answer
First, calculate the radius of curvature: . Next, apply the geometric relation: . Finally, solve for the deflection angle: .
An alpha particle (, ) enters a uniform magnetic field of width . If the particle's speed is and its exit deflection angle is , find the width of the field region.
Answer
Determine the radius: . Using the deflection geometry, .
A beam of singly ionized ions enters a magnetic field barrier of thickness . What is the minimum orbital radius required so that the ions penetrate through the barrier rather than being deflected back into the entrance half-space?
Answer
To pass completely through the barrier of thickness , the particle cannot turn around inside it. The maximum possible deflection before turning back is . Using , setting gives , which yields .