Resources
A high-energy particle accelerator operates with a design luminosity of . Protons collide at a center-of-mass energy of to produce neutral Higgs bosons (, rest mass ) with an inclusive production cross section of (, where ). (a) Convert the cross section into square meters () and square centimeters (). (b) Calculate the expected production rate of Higgs bosons per hour () during continuous steady-state beam operation.
Answer and steps
Final answer
(a) ; (b) Production rate .
Steps
Part (a): Cross Section Conversion
-
Convert to square meters ():
- A barn () is defined as:
- A picobarn () is one-trillionth of a barn:
- Multiplying by the numerical factor gives the cross section:
-
Convert to square centimeters ():
- Since , the area conversion is .
- Applying this factor:
(Note on standard prefix notation: Rigorous normalization of yields , which corresponds to the true physical cross section used in high-energy calculations).
Part (b): Production Rate of Higgs Bosons
-
Relate Luminosity, Cross Section, and Event Rate: The instantaneous reaction rate (number of events produced per second) is given by the fundamental collider relation: where:
- is the instantaneous luminosity.
- is the inclusive Higgs production cross section.
- Calculate the Rate per Second:
-
Convert to Events per Hour: Since there are in :
Expressed in scientific notation to three significant figures:
Typical errors
01 The student misconverts square meters to square centimeters by using a factor of 10² instead of 10⁴, leading to an incorrect cross section in cm² and an overestimated hourly production rate.
Sample Student Work
Reviewed by ACEpath TeacherStep-by-Step Review
Walk Through It with Your Teacher- Step 1
- Step 2Correct
When converting area units, remember that linear conversion factors must be squared: . Multiplying by instead of underestimated the area in square centimeters by a factor of .
- Step 3Correct
You correctly applied the reaction rate formula , but this step inherits the off-by-100 error from your converted cross section.
- Step 4Correct
Your conversion from seconds to hours using is correct, but the numerical answer is lowered by the previous conversion mistake.
WHAT YOU DID WELL
Compliments from Your TeacherYou correctly combined the metric prefix for pico with the definition of a barn to express the cross section in square meters.
You chose the correct physical equation to relate beam luminosity and cross section to the interaction rate.
You used the correct conversion factor of to convert the instantaneous rate into events per hour.
THE ERROR
Where Your ACEpath Teacher Spotted the MistakeYou treated the unit factor between and as rather than .
WHY IT HAPPENED
ACEpath Teacher's DiagnosisConfusing linear dimension conversion factors with two-dimensional (area) scale factors when switching between SI and CGS metric units.
REASONING PATH
Your ACEpath teacher’s suggested approach- Squaring Unit Prefixes for Area
For any linear conversion , the area relation must be squared: .
Always write down the bracketed linear relationship, such as , before executing the exponent arithmetic.
CORRECTED PATH
ACEpath Teacher's DemonstrationApply the proper area factor: .
Compute the rate per second: .
Multiply by the number of seconds in one hour: .
(a) ; (b) Production rate
02 The student calculates the event rate per second correctly but omits the unit conversion to hours, reporting the final rate per second instead of per hour.
Sample Student Work
Reviewed by ACEpath TeacherStep-by-Step Review
Walk Through It with Your Teacher- Step 1
- Step 2
- Step 3Correct
Because luminosity is given with time in seconds (), the product gives the event rate per second. To obtain the rate per hour, you need to multiply by .
WHAT YOU DID WELL
Compliments from Your TeacherYou handled the metric prefix conversions and area scaling factors cleanly.
You selected the correct physical relationship relating luminosity and cross section to the interaction rate.
THE ERROR
Where Your ACEpath Teacher Spotted the MistakeYou substituted the instantaneous rate per second directly with the unit label without scaling by the number of seconds in an hour.
WHY IT HAPPENED
ACEpath Teacher's DiagnosisOverlooking the denominator time unit in the luminosity parameter (which has units ) leads to confusing an event rate per second with an event rate per hour.
REASONING PATH
Your ACEpath teacher’s suggested approach- Check the Time Base of the Given Rate
Luminosity has time units of , so yields an instantaneous rate in .
Always write out full dimensional units alongside the numerical values to track whether the rate is per second or per hour.
- Convert Rate Time Units
.
Multiply the per-second rate by whenever an hourly production rate is requested.
CORRECTED PATH
ACEpath Teacher's DemonstrationIdentify that continuous beam operation produces every second.
Multiply by the time conversion factor: .
Round to three significant figures to match the given input parameters: .
03 The student multiplies the cross section in m² directly by the luminosity given in cm⁻²s⁻¹ without matching area units, underestimating the event rate by ten orders of magnitude.
Sample Student Work
Reviewed by ACEpath TeacherStep-by-Step Review
Walk Through It with Your Teacher- Step 1
- Step 2Correct
Luminosity is given in units of . To obtain a rate in , the cross section must be in . You substituted in (), leading to an unmatched area unit.
- Step 3Correct
Your conversion from seconds to hours using was carried out correctly, but the numerical result is off because of the mismatched area units in the previous step.
WHAT YOU DID WELL
Compliments from Your TeacherYou correctly converted picobarns to square meters and square centimeters using the definitions and .
You correctly used the fundamental event rate equation .
You correctly multiplied the per-second rate by to find the rate per hour.
THE ERROR
Where Your ACEpath Teacher Spotted the MistakeYou accidentally inserted the value of in instead of when multiplying by the luminosity.
WHY IT HAPPENED
ACEpath Teacher's DiagnosisOverlooking unit consistency across multiplicative factors: instantaneous luminosity in particle physics is conventionally stated in , requiring the cross section to be in so that the spatial dimensions cancel out.
REASONING PATH
Your ACEpath teacher’s suggested approach- Dimension Cancellation Check
.
Always write explicit unit labels next to each number before multiplying: .
CORRECTED PATH
ACEpath Teacher's DemonstrationSubstitute the cross section in square centimeters: .
Calculate the rate per second: .
Convert to an hourly rate: .
(or )
Lock it in
How do you convert an area given in square meters () into square centimeters ()?
Multiply by . Because , the area factor is .
Similar question
A top-quark production cross section in proton collisions is measured to be . Convert this cross section into and . (, )
Answer
. Steps: . Convert to by multiplying by : .
A collider has an instantaneous luminosity of . If a process has a cross section of (), find the expected event production rate in events per day.
Answer
. Steps: . Instantaneous rate . Daily rate .
An experiment requires 500 events of a rare decay channel with a cross section of . If the beam luminosity is , calculate the required continuous running time in days.
Answer
. Steps: . Event rate . Total time . In days: .