Resources

A standard laboratory DC power supply delivers an adjustable constant potential difference of V=24.0 VV = 24.0\text{ V} across a cylindrical carbon-composite resistor with a measured ohmic resistance of R=150 ΩR = 150\,\Omega. Assuming ideal copper connecting leads with negligible resistance and that the resistor operates isothermally at 20.0∘C20.0^\circ\text{C}, calculate the electric current II flowing through the resistor in milliamperes (mA\text{mA}).

Answer and steps

Final answer

160 mA160\text{ mA}

Steps

01

State the Governing Physical Principle

For an ideal or ohmic resistor operating at a constant temperature, the relationship between electric potential difference (VV), current (II), and resistance (RR) is given by Ohm's Law:

I=VRI = \frac{V}{R}

02

Identify the Given Values

  • Constant potential difference across the resistor: V=24.0 VV = 24.0\text{ V}
  • Resistance of the resistor: R=150 ΩR = 150\text{ }\Omega
03

Calculate Current in Amperes

Substitute the given values into Ohm's Law:

I=24.0 V150 Ω=0.16 AI = \frac{24.0\text{ V}}{150\text{ }\Omega} = 0.16\text{ A}

04

Convert to Milliamperes (mA\text{mA})

The question asks for the current in milliamperes. Since 1 A=1000 mA1\text{ A} = 1000\text{ mA}:

I=0.16 A×1000 mA/A=160 mAI = 0.16\text{ A} \times 1000\text{ mA/A} = 160\text{ mA}

Common Pitfall: A frequent mistake is reporting the answer in standard SI base units (A\text{A}) without converting to the requested unit of milliamperes (mA\text{mA}), or multiplying/dividing by an incorrect power of ten during the unit conversion.

Typical errors

OverviewACEpath Teacher's Diagnosis

01 The student calculates the current in amperes correctly using Ohm's law but fails to convert the final answer into milliamperes as requested.

Sample Student Work

Reviewed by ACEpath Teacher
Step-by-Step Review
Walk Through It with Your Teacher
Partially correct
  1. Step 1

    I=VR  ⟹  I=24.0150=0.16 AI = \frac{V}{R} \implies I = \frac{24.0}{150} = 0.16\text{ A}

  2. Step 2

    I=0.16 AI = 0.16\text{ A}

    Correct

    I=0.16 A×1000 mA/A=160 mAI = 0.16\text{ A} \times 1000\text{ mA/A} = 160\text{ mA}

    You stated your final answer in amperes rather than converting it to milliamperes as specified in the question.

WHAT YOU DID WELL
Compliments from Your Teacher

You correctly recalled and set up Ohm's law as I=VRI = \frac{V}{R}.

You accurately substituted the given potential difference and resistance values to find 0.16 A0.16\text{ A}.

THE ERROR
Where Your ACEpath Teacher Spotted the Mistake
Omitted unit conversion

You stopped calculating after finding the current in base amperes instead of completing the requested conversion to milliamperes.

WHY IT HAPPENED
ACEpath Teacher's Diagnosis

You overlooked the target unit specified in the prompt, leaving the final answer in SI base units.

REASONING PATH
Your ACEpath teacher’s suggested approach
Target Unit Check
  • Always verify the requested unit in the prompt before boxing your final answer.

  • Circle or highlight specified units like mA\text{mA}, kV\text{kV}, or cm\text{cm} before starting your calculation, and add a final conversion step (1 A=1000 mA1\text{ A} = 1000\text{ mA}). target units.

CORRECTED PATH
ACEpath Teacher's Demonstration
  1. Recall the metric prefix definition: 1 A=103 mA=1000 mA1\text{ A} = 10^3\text{ mA} = 1000\text{ mA}.

  2. Multiply the current in amperes by the conversion factor: 0.16 A×1000 mA/A=160 mA0.16\text{ A} \times 1000\text{ mA/A} = 160\text{ mA}.

Final answer

160 mA160\text{ mA}

NEXT STEPS
Final Takeaways from Your Teacher
  • Always re-read the final sentence of the question prompt to ensure your final answer matches the required physical unit.

  • Practice converting between standard units and metric prefixed units (such as A\text{A} to mA\text{mA} or μA\mu\text{A}).

OverviewACEpath Teacher's Diagnosis

02 The student misremembers Ohm's law as I = V × R, leading to an incorrect product of voltage and resistance.

Sample Student Work

Reviewed by ACEpath Teacher
Step-by-Step Review
Walk Through It with Your Teacher
Incorrect
  1. Step 1

    I=V×R  ⟹  I=24.0×150=3600 AI = V \times R \implies I = 24.0 \times 150 = 3600\text{ A}

    Correct

    I=VR=24.0 V150 Ω=0.16 AI = \frac{V}{R} = \frac{24.0\text{ V}}{150\text{ }\Omega} = 0.16\text{ A}

    You multiplied voltage by resistance instead of dividing. Ohm's law is V=IRV = I R, which rearranges algebraically to I=VRI = \frac{V}{R}.

  2. Step 2

    I=3600×1000=3600000 mAI = 3600 \times 1000 = 3600000\text{ mA}

    Correct

    I=0.16 A×1000 mA/A=160 mAI = 0.16\text{ A} \times 1000\text{ mA/A} = 160\text{ mA}

    You multiplied your previous value by 10001000 to convert to milliamperes, but the result is incorrect due to the formula error in Step 1.

WHAT YOU DID WELL
Compliments from Your Teacher

You correctly identified the given values for potential difference (V=24.0 VV = 24.0\text{ V}) and resistance (R=150 ΩR = 150\text{ }\Omega).

You used the correct unit conversion factor between amperes and milliamperes (1 A=1000 mA1\text{ A} = 1000\text{ mA}).

THE ERROR
Where Your ACEpath Teacher Spotted the Mistake
Formula inversion or rearrangement error

none

WHY IT HAPPENED
ACEpath Teacher's Diagnosis

You wrote Ohm's law as a product (I=V×RI = V \times R) rather than recognizing that electric current is potential difference divided by resistance (I=VRI = \frac{V}{R}).

REASONING PATH
Your ACEpath teacher’s suggested approach
Ohm's Law Triangle / Definition
  • V=I×RV = I \times R, so I=VRI = \frac{V}{R} and R=VIR = \frac{V}{I}.

  • Before calculating, isolate the target variable algebraically to verify whether values must be multiplied or divided.

Physical Reality Check
  • Higher resistance restricts flow and must reduce current.

  • Check whether multiplying VV by RR makes physical sense: a large resistance of 150 Ω150\text{ }\Omega should impede current, not amplify it to thousands of amperes.

CORRECTED PATH
ACEpath Teacher's Demonstration
  1. Apply Ohm's law properly by dividing potential difference by resistance: I=VR=24.0 V150 Ω=0.16 AI = \frac{V}{R} = \frac{24.0\text{ V}}{150\text{ }\Omega} = 0.16\text{ A}.

  2. Convert amperes to milliamperes by multiplying by 1000 mA/A1000\text{ mA/A}: I=0.16 A×1000 mA/A=160 mAI = 0.16\text{ A} \times 1000\text{ mA/A} = 160\text{ mA}.

Final answer

160 mA160\text{ mA}

NEXT STEPS
Final Takeaways from Your Teacher
  • Memorize the base form of Ohm's law as V=IRV = IR and practice isolating each of the three variables (I=VRI = \frac{V}{R} and R=VIR = \frac{V}{I}).

  • Perform a sanity check on unit magnitudes: connecting a standard 24 V24\text{ V} bench source across a 150 Ω150\text{ }\Omega resistor cannot yield thousands of amperes.

OverviewACEpath Teacher's Diagnosis

03 The student correctly calculates current in amperes but divides by 1000 instead of multiplying when converting to milliamperes.

Sample Student Work

Reviewed by ACEpath Teacher
Step-by-Step Review
Walk Through It with Your Teacher
Incorrect
  1. Step 1

    I=VR  ⟹  I=24.0150=0.16 AI = \frac{V}{R} \implies I = \frac{24.0}{150} = 0.16\text{ A}

  2. Step 2

    I=0.161000=0.00016 mAI = \frac{0.16}{1000} = 0.00016\text{ mA}

    Correct

    I=0.16 A×1000 mA/A=160 mAI = 0.16\text{ A} \times 1000\text{ mA/A} = 160\text{ mA}

    You divided by 10001000 instead of multiplying by 10001000. Because 1 A=1000 mA1\text{ A} = 1000\text{ mA}, a current in milliamperes must have a numerically larger value than in amperes.

WHAT YOU DID WELL
Compliments from Your Teacher

You selected the correct formula for Ohm's law, I=VRI = \frac{V}{R}.

You substituted the potential difference and resistance accurately to obtain 0.16 A0.16\text{ A}.

THE ERROR
Where Your ACEpath Teacher Spotted the Mistake
Metric prefix conversion inversion

You divided by 10001000 rather than multiplying by 10001000 when converting from amperes to milliamperes.

WHY IT HAPPENED
ACEpath Teacher's Diagnosis

Inverting the conversion factor between base SI units and prefixed sub-multiples: moving from a larger unit (amperes) to a smaller unit (milliamperes) requires multiplying by 10310^3, since each ampere contains 10001000 milliamperes.

REASONING PATH
Your ACEpath teacher’s suggested approach
Unit magnitude check
  • When converting from a larger unit to a smaller subunit, the numerical value must increase.

  • Check whether your target unit is smaller than your initial unit before calculating; if the unit gets smaller (from A\text{A} to mA\text{mA}), multiply by the prefix multiplier.

Dimensional cancellation
  • Set up conversion factors so unwanted units cancel algebraically: 1=1000 mA1 A1 = \frac{1000\text{ mA}}{1\text{ A}}.

  • Write (0.16 A)×(1000 mA1 A)(0.16\text{ A}) \times \left(\frac{1000\text{ mA}}{1\text{ A}}\right) to ensure that amperes cancel in numerator and denominator.

CORRECTED PATH
ACEpath Teacher's Demonstration
  1. Apply the conversion factor between amperes and milliamperes: 1 A=1000 mA1\text{ A} = 1000\text{ mA}.

  2. Multiply the current in amperes by 1000 mA/A1000\text{ mA/A}: I=0.16×1000 mA=160 mAI = 0.16 \times 1000\text{ mA} = 160\text{ mA}.

Final answer

160 mA160\text{ mA}

NEXT STEPS
Final Takeaways from Your Teacher
  • Practice using dimensional analysis cancellation fractions when changing metric prefixes.

  • Perform a quick mental sanity check on unit size: smaller units always yield a larger numerical count.

Lock it in

Similar question

01

A 9.0 V9.0\text{ V} battery is connected across a 300 Ω300\text{ }\Omega resistor. Calculate the current II flowing through the resistor in milliamperes (mA\text{mA}).

Answer

I=VR=9.0 V300 Ω=0.030 AI = \frac{V}{R} = \frac{9.0\text{ V}}{300\text{ }\Omega} = 0.030\text{ A}. Converting to milliamperes: 0.030 A×1000 mA/A=30 mA0.030\text{ A} \times 1000\text{ mA/A} = 30\text{ mA}.

02

An LED circuit requires a current of 25 mA25\text{ mA} when a potential difference of 3.0 V3.0\text{ V} is applied across an unknown resistor. Calculate the resistance RR in ohms (Ω\Omega).

Answer

Convert current to amperes first: I=25 mA=0.025 AI = 25\text{ mA} = 0.025\text{ A}. Then apply Ohm's law: R=VI=3.0 V0.025 A=120 ΩR = \frac{V}{I} = \frac{3.0\text{ V}}{0.025\text{ A}} = 120\text{ }\Omega.

03

A potential difference of 12.0 V12.0\text{ V} is applied across a 4.8 kΩ4.8\text{ k}\Omega resistor. Determine the electric current II in milliamperes (mA\text{mA}).

Answer

Convert resistance to ohms: R=4.8 kΩ=4800 ΩR = 4.8\text{ k}\Omega = 4800\text{ }\Omega. Compute current: I=12.0 V4800 Ω=0.0025 AI = \frac{12.0\text{ V}}{4800\text{ }\Omega} = 0.0025\text{ A}. Convert to milliamperes: 0.0025 A×1000 mA/A=2.5 mA0.0025\text{ A} \times 1000\text{ mA/A} = 2.5\text{ mA} (or directly: 12.0 V4.8 kΩ=2.5 mA\frac{12.0\text{ V}}{4.8\text{ k}\Omega} = 2.5\text{ mA}).

Loading workspace…