Resources
In a laboratory motion-sensor experiment, an ultrasonic detector records the position and velocity of a cart rolling down an inclined air track. The sensor's data acquisition system logs the cart's velocity as at timestamp and at timestamp directed down the track. Based on this experimental time-series data, calculate the average acceleration of the cart along the incline.
Answer and steps
Final answer
Steps
1. Identify the Definition of Average Acceleration
Average acceleration, , is defined as the rate of change of velocity over a given time interval:
2. Extract the Given Experimental Data
From the sensor logs:
- Initial time:
- Initial velocity:
- Final time:
- Final velocity:
Both velocities are directed down the track, so we can define the downward direction along the incline as positive.
3. Compute the Change in Velocity () and Elapsed Time ()
Calculate the change in velocity:
Calculate the elapsed time:
4. Calculate the Average Acceleration
Substitute the values into the formula:
Rounding to three significant figures (matching the data's precision):
Common Pitfall to Avoid
- Order of Subtraction: Always subtract the initial value from the final value (). Reversing this order () yields the wrong sign for acceleration.
Typical errors
01 The student divides the change in velocity by the final timestamp rather than the elapsed time interval, yielding an incorrect acceleration of 0.338 m/s².
Sample Student Work
Reviewed by ACEpath TeacherStep-by-Step Review
Walk Through It with Your Teacher- Step 1
- Step 2Correct
You used the final clock reading in the denominator instead of the elapsed time interval .
- Step 3Correct
Because the denominator used instead of , your final acceleration value was too small.
WHAT YOU DID WELL
Compliments from Your TeacherYou correctly identified the initial and final velocity values from the problem statement.
You correctly computed the change in velocity as .
THE ERROR
Where Your ACEpath Teacher Spotted the MistakeYou divided by the single clock reading instead of subtracting to find the elapsed time .
WHY IT HAPPENED
ACEpath Teacher's DiagnosisTreating a clock timestamp as an elapsed duration causes you to overlook the non-zero starting time .
REASONING PATH
Your ACEpath teacher’s suggested approach- Clock Reading vs. Elapsed Time
Average acceleration is defined by the interval , not by the final instant , unless .
Always compute separately before dividing.
CORRECTED PATH
ACEpath Teacher's DemonstrationCalculate the elapsed time interval: .
Divide the change in velocity by the elapsed time: .
02 The student inverts the definition of acceleration as elapsed time divided by change in velocity, obtaining 1.79 s²/m.
Sample Student Work
Reviewed by ACEpath TeacherStep-by-Step Review
Walk Through It with Your Teacher- Step 1
- Step 2
- Step 3Correct
You inverted the formula for acceleration. Acceleration is the rate of change of velocity with respect to time (), which places time in the denominator.
- Step 4Correct
This numerical result directly follows from dividing elapsed time by velocity change rather than the correct ratio.
WHAT YOU DID WELL
Compliments from Your TeacherYou extracted the correct velocity and time values from the experimental data.
You correctly calculated both the velocity difference and elapsed time interval.
You included units throughout your work and rounded your numerical evaluation reasonably.
THE ERROR
Where Your ACEpath Teacher Spotted the MistakeYou set up the acceleration ratio upside down as instead of .
WHY IT HAPPENED
ACEpath Teacher's DiagnosisYou reversed the dependent and independent variables in the rate definition, forgetting that acceleration measures how much velocity changes per unit of time.
REASONING PATH
Your ACEpath teacher’s suggested approach- Recall the Physical Definition
Acceleration is the time rate of change of velocity: .
Always place the change in velocity in the numerator and the time duration in the denominator.
- Check the Dimensional Units
Acceleration must have units of (or ).
Divide units explicitly: . If your formula gives , you know the fraction is inverted.
CORRECTED PATH
ACEpath Teacher's DemonstrationSubstitute and into the standard acceleration formula: .
Evaluate the division: .
Round to three significant figures to match the given data precision: .
03 The student adds the initial and final timestamps in the denominator instead of subtracting them, calculating an acceleration of 0.242 m/s².
Sample Student Work
Reviewed by ACEpath TeacherStep-by-Step Review
Walk Through It with Your Teacher- Step 1
- Step 2Correct
The symbol represents a change or difference (). You added the two clock readings () rather than subtracting the initial timestamp from the final timestamp ().
- Step 3Correct
You correctly set up the ratio , but this step inherited your incorrect value for .
- Step 4Correct
Your arithmetic division is accurate for your substituted values, but the final numerical result is incorrect due to the elapsed time error in Step 2.
WHAT YOU DID WELL
Compliments from Your TeacherYou correctly identified that average acceleration is the ratio of change in velocity to elapsed time, .
You correctly calculated the change in velocity .
You performed the final division accurately and included proper units of .
THE ERROR
Where Your ACEpath Teacher Spotted the Mistakeno
WHY IT HAPPENED
ACEpath Teacher's DiagnosisYou treated the Greek letter delta () as a sum of values rather than a difference between final and initial states when calculating elapsed time. In physics, any interval always means .
REASONING PATH
Your ACEpath teacher’s suggested approach- Meaning of Delta ($\Delta$)
For any variable , . It never denotes the sum of the two readings.
Whenever you see or write , write out explicitly before substituting numerical values.
- Clock Time vs. Elapsed Time
Clock timestamps indicate when events occur; elapsed time measures how long passed between them.
Check that your computed time interval is strictly smaller than the final clock reading whenever .
CORRECTED PATH
ACEpath Teacher's DemonstrationCalculate elapsed time as the difference between timestamps: .
Substitute and into the average acceleration definition: .
Round to three significant figures: .
Lock it in
What is the formula for average acceleration when given two timestamps and ?
. Acceleration depends on the elapsed duration , never a single clock reading.
Similar question
A glider on an air track passes the first photogate at moving at , and passes the second photogate at moving at . Find its average acceleration.
Answer
. , , .
A braking test vehicle records a velocity of at timestamp and comes to a complete stop () at timestamp . What is the vehicle's average acceleration?
Answer
. , , .
A motorized cart moves along a straight rail. An optical encoder logs the cart at three instants: (), (), and (). Determine the average acceleration specifically between and , and explain why the data at is excluded.
Answer
. The interval of interest spans only to , so is outside this window. and , giving .