Resources

A high-precision optical laboratory table specifies a maximum allowable surface deflection rate under acoustic vibration of 0.0500 mm/min0.0500\text{ mm/min}. During an experiment, an interferometer measures the table's instantaneous vibration speed as v=8.50×10−7 m/sv = 8.50 \times 10^{-7}\text{ m/s}. Convert this measured speed into millimeters per minute (mm/min\text{mm/min}), and determine whether the table remains strictly within the operational deflection limit. State both the converted value and a definitive threshold conclusion.

Answer and steps

Final answer

0.0510 mm/min0.0510\text{ mm/min}; the table exceeds the operational threshold limit (0.0510 mm/min>0.0500 mm/min0.0510\text{ mm/min} > 0.0500\text{ mm/min}).

Steps

01

Identify the Given Values and Conversion Factors

The given measured speed is: v=8.50×10−7 m/sv = 8.50 \times 10^{-7}\text{ m/s}

The target units are millimeters per minute (mm/min\text{mm/min}). The fundamental conversion equivalence relations are:

  • Length: 1 m=103 mm1\text{ m} = 10^3\text{ mm} (or 1000 mm1000\text{ mm})
  • Time: 1 min=60 s1\text{ min} = 60\text{ s}

02

Apply Dimensional Analysis

Using the factor-label method (dimensional analysis), arrange the conversion factors so that unwanted units cancel out:

v=(8.50×10−7ms)×(103 mm1 m)×(60 s1 min)v = \left(8.50 \times 10^{-7}\frac{\text{m}}{\text{s}}\right) \times \left(\frac{10^3\text{ mm}}{1\text{ m}}\right) \times \left(\frac{60\text{ s}}{1\text{ min}}\right)

Common Pitfall: Because seconds (s\text{s}) appear in the denominator, the conversion factor must place seconds in the numerator (60 s1 min\frac{60\text{ s}}{1\text{ min}}). Dividing by 6060 instead of multiplying is a frequent error.


03

Calculate the Converted Speed

Multiply the numerical values:

v=8.50×10−7×1000×60 mm/minv = 8.50 \times 10^{-7} \times 1000 \times 60\text{ mm/min} v=8.50×10−4×60 mm/minv = 8.50 \times 10^{-4} \times 60\text{ mm/min} v=5.10×10−2 mm/min=0.0510 mm/minv = 5.10 \times 10^{-2}\text{ mm/min} = 0.0510\text{ mm/min}

Maintaining three significant figures (from the given value 8.50×10−7 m/s8.50 \times 10^{-7}\text{ m/s}), the converted speed is: v=0.0510 mm/minv = 0.0510\text{ mm/min}


04

Compare with the Allowable Threshold

The maximum allowable deflection rate is: vlimit=0.0500 mm/minv_{\text{limit}} = 0.0500\text{ mm/min}

Comparing the measured deflection rate to the threshold: 0.0510 mm/min>0.0500 mm/min0.0510\text{ mm/min} > 0.0500\text{ mm/min}

Therefore, the table's instantaneous vibration speed exceeds the operational deflection limit.

Typical errors

OverviewACEpath Teacher's Diagnosis

01 The student divides by 60 instead of multiplying by 60 when converting seconds in the denominator to minutes, obtaining an erroneously small deflection rate.

Sample Student Work

Reviewed by ACEpath Teacher
Step-by-Step Review
Walk Through It with Your Teacher
Incorrect
  1. Step 1

    v=(8.50×10−7 m/s)×1000 mm/m  ⟹  8.50×10−4 mm/sv = (8.50 \times 10^{-7}\text{ m/s}) \times 1000\text{ mm/m} \implies 8.50 \times 10^{-4}\text{ mm/s}

  2. Step 2

    v=(8.50×10−4 mm/s)/60  ⟹  1.42×10−5 mm/minv = (8.50 \times 10^{-4}\text{ mm/s}) / 60 \implies 1.42 \times 10^{-5}\text{ mm/min}

    Correct

    v=(8.50×10−4 mm/s)×(60 s1 min)=5.10×10−2 mm/min=0.0510 mm/minv = (8.50 \times 10^{-4}\text{ mm/s}) \times \left(\frac{60\text{ s}}{1\text{ min}}\right) = 5.10 \times 10^{-2}\text{ mm/min} = 0.0510\text{ mm/min}

    Because seconds (s\text{s}) is in the denominator, you need to multiply by 60 s/min60\text{ s/min} rather than divide by 6060. Since 1 minute1\text{ minute} has 60 seconds60\text{ seconds}, an object travels 6060 times as far in one full minute as it does in one second.

  3. Step 3

    1.42×10−5 mm/min<0.0500 mm/min  ⟹  The table remains strictly within the operational deflection limit.1.42 \times 10^{-5}\text{ mm/min} < 0.0500\text{ mm/min} \implies \text{The table remains strictly within the operational deflection limit.}

    Correct

    0.0510 mm/min>0.0500 mm/min  ⟹  The table exceeds the operational threshold limit.0.0510\text{ mm/min} > 0.0500\text{ mm/min} \implies \text{The table exceeds the operational threshold limit.}

    Your comparison logic correctly followed your calculated number, but because the speed was underestimated in the previous step, the conclusion was reversed.

WHAT YOU DID WELL
Compliments from Your Teacher

You correctly identified the equivalence 1 m=1000 mm1\text{ m} = 1000\text{ mm} and applied it to the numerator.

You accurately resolved scientific notation arithmetic when simplifying 8.50×10−7×1000=8.50×10−48.50 \times 10^{-7} \times 1000 = 8.50 \times 10^{-4}.

You clearly compared your calculated value directly against the operational threshold.

THE ERROR
Where Your ACEpath Teacher Spotted the Mistake
Denominator unit conversion inversion

no

WHY IT HAPPENED
ACEpath Teacher's Diagnosis

You associated converting from a smaller time unit (seconds) to a larger time unit (minutes) with division, forgetting that the unit being converted sits in the denominator of a rate.

REASONING PATH
Your ACEpath teacher’s suggested approach
Denominator Unit Inversion Rule
  • When converting a unit in the denominator, place the original unit in the numerator of your conversion factor so that it cancels algebraically: 1s×60 s1 min=60min\frac{1}{\text{s}} \times \frac{60\text{ s}}{1\text{ min}} = \frac{60}{\text{min}}.

  • Always write out conversion factors as explicit fractions showing units canceling before performing any numerical multiplication or division.

Physical Reality Sanity Check
  • A rate per minute must be 6060 times larger than a rate per second, because sixty seconds of motion accumulate in each minute.

  • Ask yourself: 'Should something moving every second cover more distance or less distance over an entire minute?' If more, the number must increase.

CORRECTED PATH
ACEpath Teacher's Demonstration
  1. Multiply the intermediate speed by the time conversion ratio: v=(8.50×10−4 mm/s)×(60 s1 min)v = (8.50 \times 10^{-4}\text{ mm/s}) \times \left(\frac{60\text{ s}}{1\text{ min}}\right).

  2. Calculate the numerical product: 8.50×10−4×60=5.10×10−2 mm/min=0.0510 mm/min8.50 \times 10^{-4} \times 60 = 5.10 \times 10^{-2}\text{ mm/min} = 0.0510\text{ mm/min}.

  3. Compare the converted value to the operational threshold: 0.0510 mm/min>0.0500 mm/min0.0510\text{ mm/min} > 0.0500\text{ mm/min}.

Final answer

0.0510 mm/min0.0510\text{ mm/min}; the table exceeds the operational threshold limit.

NEXT STEPS
Final Takeaways from Your Teacher
  • Practice using the factor-label method with explicit unit fractions to ensure denominator units cancel properly.

  • Perform a physical intuition check on rate conversions to confirm whether the numerical value should grow or shrink.

OverviewACEpath Teacher's Diagnosis

02 The student confuses the metric prefix milli- with micro- and uses 10⁶ mm/m instead of 10³ mm/m, resulting in an overly large converted value.

Sample Student Work

Reviewed by ACEpath Teacher
Step-by-Step Review
Walk Through It with Your Teacher
Partially correct
  1. Step 1

    v=(8.50×10−7 m/s)×106 mm/m×60 s/minv = (8.50 \times 10^{-7}\text{ m/s}) \times 10^6\text{ mm/m} \times 60\text{ s/min}

    Correct

    v=(8.50×10−7 m/s)×(103 mm1 m)×(60 s1 min)v = (8.50 \times 10^{-7}\text{ m/s}) \times \left(\frac{10^3\text{ mm}}{1\text{ m}}\right) \times \left(\frac{60\text{ s}}{1\text{ min}}\right)

    You correctly placed seconds in the numerator to cancel the denominator unit, but you used 106 mm10^6\text{ mm} per meter instead of 103 mm10^3\text{ mm} per meter. The prefix milli- means 10−310^{-3}, so 1 m=103 mm1\text{ m} = 10^3\text{ mm} (10610^6 corresponds to micrometers, μm\mu\text{m}).

  2. Step 2

    v=51.0 mm/minv = 51.0\text{ mm/min}

    Correct

    v=0.0510 mm/minv = 0.0510\text{ mm/min} (or 5.10×10−2 mm/min5.10 \times 10^{-2}\text{ mm/min})

    Your arithmetic (8.50×10−7)×106×60=51.0(8.50 \times 10^{-7}) \times 10^6 \times 60 = 51.0 correctly followed your setup, but the numerical answer is off by a factor of 10310^3 due to the earlier prefix error.

  3. Step 3

    51.0 mm/min>0.0500 mm/min  ⟹  The table does not remain within the operational deflection limit.51.0\text{ mm/min} > 0.0500\text{ mm/min} \implies \text{The table does not remain within the operational deflection limit.}

    Correct

    0.0510 mm/min>0.0500 mm/min  ⟹  The table exceeds the operational threshold limit.0.0510\text{ mm/min} > 0.0500\text{ mm/min} \implies \text{The table exceeds the operational threshold limit.}

    You correctly compared your calculated value to the 0.0500 mm/min0.0500\text{ mm/min} threshold. Although your final qualitative conclusion happens to match the true outcome, it was evaluated against an inflated numerical value.

WHAT YOU DID WELL
Compliments from Your Teacher

You correctly recognized that converting seconds in the denominator to minutes requires multiplying by 60 s/min60\text{ s/min}.

You correctly maintained three significant figures in your final numerical value.

You set up a clear comparison against the allowable threshold limit.

THE ERROR
Where Your ACEpath Teacher Spotted the Mistake
Metric Prefix Confusion (milli- vs. micro-)

no

WHY IT HAPPENED
ACEpath Teacher's Diagnosis

You confused the SI prefix milli- (10−310^{-3}, meaning 1 m=103 mm1\text{ m} = 10^3\text{ mm}) with micro- (10−610^{-6}, meaning 1 m=106 μm1\text{ m} = 10^6\text{ }\mu\text{m}).

REASONING PATH
Your ACEpath teacher’s suggested approach
Metric Prefix Base Relations
  • milli- (m)=10−3  ⟹  1 m=103 mm\text{milli- (m)} = 10^{-3} \implies 1\text{ m} = 10^3\text{ mm}; micro- (μ)=10−6  ⟹  1 m=106 μm\text{micro- (}\mu\text{)} = 10^{-6} \implies 1\text{ m} = 10^6\text{ }\mu\text{m}.

  • Whenever you convert meters to millimeters, write down 103 mm=1 m10^3\text{ mm} = 1\text{ m} before multiplying.

CORRECTED PATH
ACEpath Teacher's Demonstration
  1. Replace 106 mm/m10^6\text{ mm/m} with 103 mm/m10^3\text{ mm/m}: v=(8.50×10−7 m/s)×(103 mm/m)×(60 s/min)v = (8.50 \times 10^{-7}\text{ m/s}) \times \left(10^3\text{ mm/m}\right) \times (60\text{ s/min})

  2. Compute the product: v=8.50×10−4×60=5.10×10−2 mm/min=0.0510 mm/minv = 8.50 \times 10^{-4} \times 60 = 5.10 \times 10^{-2}\text{ mm/min} = 0.0510\text{ mm/min}

  3. Compare with the operational threshold: 0.0510 mm/min>0.0500 mm/min0.0510\text{ mm/min} > 0.0500\text{ mm/min}

Final answer

0.0510 mm/min0.0510\text{ mm/min}; the table exceeds the operational deflection limit.

NEXT STEPS
Final Takeaways from Your Teacher
  • Review the common SI metric prefixes: milli (10−310^{-3}), micro (10−610^{-6}), and nano (10−910^{-9}).

  • Write out complete conversion fractions with both numerator and denominator units so you can visually verify unit cancellation.

OverviewACEpath Teacher's Diagnosis

03 The student converts seconds to hours rather than minutes by multiplying by 3600, yielding 3.06 mm/min.

Sample Student Work

Reviewed by ACEpath Teacher
Step-by-Step Review
Walk Through It with Your Teacher
Partially correct
  1. Step 1

    v=(8.50×10−7 m/s)×1000 mm/m  ⟹  v=8.50×10−4 mm/sv = (8.50 \times 10^{-7}\text{ m/s}) \times 1000\text{ mm/m} \implies v = 8.50 \times 10^{-4}\text{ mm/s}

  2. Step 2

    v=(8.50×10−4 mm/s)×3600=3.06 mm/minv = (8.50 \times 10^{-4}\text{ mm/s}) \times 3600 = 3.06\text{ mm/min}

    Correct

    v=(8.50×10−4 mm/s)×(60 s1 min)=0.0510 mm/minv = (8.50 \times 10^{-4}\text{ mm/s}) \times \left(\frac{60\text{ s}}{1\text{ min}}\right) = 0.0510\text{ mm/min}

    You multiplied by 36003600 rather than 6060. There are 60 seconds60\text{ seconds} in 1 minute1\text{ minute} (3600 seconds3600\text{ seconds} are in 1 hour1\text{ hour}), so the correct time conversion factor is 60 s/min60\text{ s/min}.

  3. Step 3

    3.06 mm/min>0.0500 mm/min  ⟹  The table does not remain within the operational limit.3.06\text{ mm/min} > 0.0500\text{ mm/min} \implies \text{The table does not remain within the operational limit.}

    Correct

    0.0510 mm/min>0.0500 mm/min  ⟹  The table exceeds the operational threshold limit.0.0510\text{ mm/min} > 0.0500\text{ mm/min} \implies \text{The table exceeds the operational threshold limit.}

    Your comparison reasoning is logically sound, but it evaluates your erroneous value of 3.06 mm/min3.06\text{ mm/min} rather than the correct value of 0.0510 mm/min0.0510\text{ mm/min}.

WHAT YOU DID WELL
Compliments from Your Teacher

You correctly converted the length unit from meters to millimeters using 1 m=1000 mm1\text{ m} = 1000\text{ mm}.

You recognized that converting a denominator unit of seconds into minutes requires multiplying the rate by the number of seconds in that time interval.

You set up the final inequality comparison between your calculated speed and the operational limit properly.

THE ERROR
Where Your ACEpath Teacher Spotted the Mistake
Time Unit Conversion Error

You used the conversion factor for hours (3600 s3600\text{ s}) instead of minutes (60 s60\text{ s}).

WHY IT HAPPENED
ACEpath Teacher's Diagnosis

You substituted the factor 3600 s3600\text{ s} into the numerator without explicitly writing out unit labels in the factor-label method, confusing the seconds-to-minutes ratio (60 s=1 min60\text{ s} = 1\text{ min}) with the seconds-to-hours ratio (3600 s=1 h3600\text{ s} = 1\text{ h}).

REASONING PATH
Your ACEpath teacher’s suggested approach
Time Equivalence Verification
  • 1 min=60 s1\text{ min} = 60\text{ s} and 1 h=3600 s1\text{ h} = 3600\text{ s}.

  • Always write the full dimensional fraction (60 s1 min)\left(\frac{60\text{ s}}{1\text{ min}}\right) so unit labels cancel visibly before calculating.

CORRECTED PATH
ACEpath Teacher's Demonstration
  1. Multiply by the correct time conversion factor: v=(8.50×10−4 mm/s)×(60 s1 min)v = (8.50 \times 10^{-4}\text{ mm/s}) \times \left(\frac{60\text{ s}}{1\text{ min}}\right)

  2. Evaluate the product: v=0.0510 mm/minv = 0.0510\text{ mm/min}

  3. Compare with the maximum allowable threshold: 0.0510 mm/min>0.0500 mm/min0.0510\text{ mm/min} > 0.0500\text{ mm/min}

Final answer

0.0510 mm/min0.0510\text{ mm/min}; the table exceeds the operational threshold limit (0.0510 mm/min>0.0500 mm/min0.0510\text{ mm/min} > 0.0500\text{ mm/min}).

NEXT STEPS
Final Takeaways from Your Teacher
  • Write down explicit unit fractions with units attached to every number (e.g., 60 s1 min\frac{60\text{ s}}{1\text{ min}}) rather than bare numerical multipliers.

  • Double-check whether target rates are per minute or per hour before selecting 6060 versus 36003600.

Lock it in

Similar question

01

A microfluidic pump dispenses fluid at a rate of 4.20×10−4 mL/s4.20 \times 10^{-4}\text{ mL/s}. Convert this flow rate into milliliters per hour (mL/h\text{mL/h}).

Answer

1.51 mL/h1.51\text{ mL/h}. Using dimensional analysis: (4.20×10−4 mL/s)×(3600 s1 h)=1.512 mL/h≈1.51 mL/h(4.20 \times 10^{-4}\text{ mL/s}) \times \left(\frac{3600\text{ s}}{1\text{ h}}\right) = 1.512\text{ mL/h} \approx 1.51\text{ mL/h} (to 3 significant figures).

02

A high-speed laser beam drifts across a sensor at 2.50×10−5 m/s2.50 \times 10^{-5}\text{ m/s}. The sensor's tolerance threshold is 1.20 mm/min1.20\text{ mm/min}. Convert the drift speed to mm/min\text{mm/min} and determine whether it exceeds the tolerance threshold.

Answer

1.50 mm/min1.50\text{ mm/min}; it exceeds the threshold (1.50 mm/min>1.20 mm/min1.50\text{ mm/min} > 1.20\text{ mm/min}). Calculation: (2.50×10−5 m/s)×(103 mm1 m)×(60 s1 min)=1.50 mm/min(2.50 \times 10^{-5}\text{ m/s}) \times \left(\frac{10^3\text{ mm}}{1\text{ m}}\right) \times \left(\frac{60\text{ s}}{1\text{ min}}\right) = 1.50\text{ mm/min}.

03

An optical fiber coating applicator deposits material at a rate of 1.80 mg/(cm⋅s)1.80\text{ mg/(cm}\cdot\text{s)}. Convert this deposition rate into grams per meter-minute [g/(m⋅min)\text{g/(m}\cdot\text{min})].

Answer

10.8 g/(m⋅min)10.8\text{ g/(m}\cdot\text{min}). Steps: multiply by (1 g1000 mg)\left(\frac{1\text{ g}}{1000\text{ mg}}\right), multiply by (100 cm1 m)\left(\frac{100\text{ cm}}{1\text{ m}}\right) to convert length in the denominator, and multiply by (60 s1 min)\left(\frac{60\text{ s}}{1\text{ min}}\right) to convert time in the denominator: 1.80×11000×100×60=10.8 g/(m⋅min)1.80 \times \frac{1}{1000} \times 100 \times 60 = 10.8\text{ g/(m}\cdot\text{min}).

Loading workspace…