Resources

In an introductory physics laboratory, a dual-trace digital storage oscilloscope is used to measure an unknown sinusoidal voltage signal V1(t)V_1(t) against a reference function generator signal V2(t)=V0cos⁡(2πft)V_2(t) = V_0\cos(2\pi f t). The time-base setting of the oscilloscope is adjusted to 50.0 μs/div50.0\,\mu\text{s/div}. On the display grid, one complete cycle of signal V1(t)V_1(t) spans exactly 8.00 horizontal divisions8.00\text{ horizontal divisions}, its peak-to-peak vertical deflection spans 6.40 divisions6.40\text{ divisions} at a vertical sensitivity of 0.500 V/div0.500\text{ V/div}, and the positive-going zero crossing of V1(t)V_1(t) lags that of V2(t)V_2(t) by 1.60 divisions1.60\text{ divisions}. Calculate: (a) the amplitude AA of signal V1(t)V_1(t) in volts, (b) the period TT and frequency ff of the signal, and (c) the phase lag Δϕ\Delta\phi of signal V1(t)V_1(t) relative to V2(t)V_2(t) in radians.

Answer and steps

Final answer

(a) A=1.60 VA = 1.60\text{ V}; (b) T=4.00×10−4 sT = 4.00 \times 10^{-4}\text{ s} (400 μs400\,\mu\text{s}), f=2.50×103 Hzf = 2.50 \times 10^3\text{ Hz} (2.50 kHz2.50\text{ kHz}); (c) Δϕ=0.400π rad≈1.26 rad\Delta\phi = 0.400\pi\text{ rad} \approx 1.26\text{ rad}

Steps

(a) Amplitude of Signal V1(t)V_1(t)

An oscilloscope display indicates peak-to-peak voltage (VppV_{\text{pp}}), which is the difference between the maximum positive crest and the minimum negative trough: Vpp=(vertical divisions)×(vertical sensitivity)V_{\text{pp}} = (\text{vertical divisions}) \times (\text{vertical sensitivity})

Substitute the given values: Vpp=6.40 div×0.500 V/div=3.20 VV_{\text{pp}} = 6.40\text{ div} \times 0.500\text{ V/div} = 3.20\text{ V}

For a symmetric sinusoidal wave centered at zero, the amplitude AA is half of the peak-to-peak voltage: A=Vpp2=3.20 V2=1.60 VA = \frac{V_{\text{pp}}}{2} = \frac{3.20\text{ V}}{2} = 1.60\text{ V}

Common Pitfall: Do not confuse peak-to-peak voltage with amplitude. The amplitude measures deflection from the central equilibrium axis to a peak, so A=12VppA = \frac{1}{2}V_{\text{pp}}.


(b) Period and Frequency of the Signal

The period TT is the time required to complete one full cycle. It is calculated by multiplying the horizontal divisions per cycle by the time-base setting: T=(horizontal divisions per cycle)×(time-base)T = (\text{horizontal divisions per cycle}) \times (\text{time-base}) T=8.00 div×50.0 μs/div=400 μs=4.00×10−4 sT = 8.00\text{ div} \times 50.0\,\mu\text{s/div} = 400\,\mu\text{s} = 4.00 \times 10^{-4}\text{ s}

Frequency ff is the reciprocal of the period: f=1T=14.00×10−4 s=2.50×103 Hz=2.50 kHzf = \frac{1}{T} = \frac{1}{4.00 \times 10^{-4}\text{ s}} = 2.50 \times 10^3\text{ Hz} = 2.50\text{ kHz}


(c) Phase Lag Δϕ\Delta\phi of V1(t)V_1(t) Relative to V2(t)V_2(t)

One complete cycle of TT corresponds to an angular span of 2π radians2\pi\text{ radians} (or 360∘360^\circ) across 8.00 divisions8.00\text{ divisions}.

The horizontal shift between corresponding points (such as positive-going zero crossings) represents the time delay Δt\Delta t. The phase difference Δϕ\Delta\phi in radians is directly proportional to the fraction of the full period represented by this shift: Δϕ=2π⋅ΔxXT\Delta\phi = 2\pi \cdot \frac{\Delta x}{X_T}

where Δx=1.60 div\Delta x = 1.60\text{ div} is the horizontal separation and XT=8.00 divX_T = 8.00\text{ div} is the horizontal division span of one cycle: Δϕ=2π⋅1.60 div8.00 div=2π×0.200=0.400π rad≈1.26 rad\Delta\phi = 2\pi \cdot \frac{1.60\text{ div}}{8.00\text{ div}} = 2\pi \times 0.200 = 0.400\pi\text{ rad} \approx 1.26\text{ rad}

Since the zero crossing of V1(t)V_1(t) occurs after that of V2(t)V_2(t), signal V1(t)V_1(t) lags reference signal V2(t)V_2(t) by 0.400π rad0.400\pi\text{ rad} (or approximately 1.26 rad1.26\text{ rad}).

Typical errors

OverviewACEpath Teacher's Diagnosis

01 The student confuses the peak-to-peak voltage deflection with the wave amplitude, failing to divide by two.

Sample Student Work

Reviewed by ACEpath Teacher
Step-by-Step Review
Walk Through It with Your Teacher
Partially correct
  1. Step 1

    Vpp=6.40 div×0.500 V/div=3.20 VV_{\text{pp}} = 6.40\text{ div} \times 0.500\text{ V/div} = 3.20\text{ V}

  2. Step 2

    A=3.20 VA = 3.20\text{ V}

    Correct

    A=Vpp2=3.20 V2=1.60 VA = \frac{V_{\text{pp}}}{2} = \frac{3.20\text{ V}}{2} = 1.60\text{ V}

    For a symmetric sinusoidal wave centered about zero, the amplitude AA is the maximum displacement from equilibrium to a peak, which is half of the peak-to-peak voltage (A=Vpp2A = \frac{V_{\text{pp}}}{2}).

  3. Step 3

    T=8.00 div×50.0 μs/div=400 μs=4.00×10−4 s  ⟹  f=1T=14.00×10−4 s=2500 HzT = 8.00\text{ div} \times 50.0\,\mu\text{s/div} = 400\,\mu\text{s} = 4.00 \times 10^{-4}\text{ s} \implies f = \frac{1}{T} = \frac{1}{4.00 \times 10^{-4}\text{ s}} = 2500\text{ Hz}

  4. Step 4

    Δϕ=(1.60 div8.00 div)×2π=0.400π rad≈1.26 rad\Delta\phi = \left(\frac{1.60\text{ div}}{8.00\text{ div}}\right) \times 2\pi = 0.400\pi\text{ rad} \approx 1.26\text{ rad}

WHAT YOU DID WELL
Compliments from Your Teacher

You correctly calculated the peak-to-peak voltage from the oscilloscope grid and sensitivity.

You calculated the period and frequency accurately using the time-base setting.

You correctly calculated the phase difference in radians using the proportional horizontal shift.

THE ERROR
Where Your ACEpath Teacher Spotted the Mistake
Peak-to-Peak vs Amplitude Confusion

You equated the amplitude directly to the peak-to-peak voltage without dividing by 2.

WHY IT HAPPENED
ACEpath Teacher's Diagnosis

Confusing peak-to-peak value (total vertical span from trough to crest) with amplitude (displacement from center line to crest).

REASONING PATH
Your ACEpath teacher’s suggested approach
Amplitude vs. Peak-to-Peak
  • For a standard zero-centered sinusoidal waveform, Vpp=2AV_{\text{pp}} = 2A, meaning A=12VppA = \frac{1}{2}V_{\text{pp}}.

  • Whenever you calculate VppV_{\text{pp}} from an oscilloscope screen, divide by 2 to obtain the amplitude AA.

CORRECTED PATH
ACEpath Teacher's Demonstration
  1. Use the relationship between peak-to-peak voltage and amplitude: A=Vpp2A = \frac{V_{\text{pp}}}{2}.

  2. Substitute Vpp=3.20 VV_{\text{pp}} = 3.20\text{ V}: A=3.20 V2=1.60 VA = \frac{3.20\text{ V}}{2} = 1.60\text{ V}.

Final answer

(a) A=1.60 VA = 1.60\text{ V}; (b) T=4.00×10−4 sT = 4.00 \times 10^{-4}\text{ s}, f=2.50×103 Hzf = 2.50 \times 10^3\text{ Hz}; (c) Δϕ=0.400π rad≈1.26 rad\Delta\phi = 0.400\pi\text{ rad} \approx 1.26\text{ rad}

NEXT STEPS
Final Takeaways from Your Teacher
  • Before writing down amplitude AA, check whether the measured dimension spans trough-to-crest (VppV_{\text{pp}}) or centerline-to-crest (AA).

  • Practice reading both peak-to-peak and zero-to-peak values on oscilloscope grids.

OverviewACEpath Teacher's Diagnosis

02 The student forgets to convert microsecond units to seconds when calculating the frequency, yielding an answer in incorrect units or off by six orders of magnitude.

Sample Student Work

Reviewed by ACEpath Teacher
Step-by-Step Review
Walk Through It with Your Teacher
Partially correct
  1. Step 1

    Vpp=6.40 div×0.500 V/div=3.20 V  ⟹  A=3.20 V2=1.60 VV_{\text{pp}} = 6.40\text{ div} \times 0.500\text{ V/div} = 3.20\text{ V} \implies A = \frac{3.20\text{ V}}{2} = 1.60\text{ V}

  2. Step 2

    T=8.00 div×50.0 μs/div=400 μsT = 8.00\text{ div} \times 50.0\,\mu\text{s/div} = 400\,\mu\text{s}

  3. Step 3

    f=1400=0.0025 Hzf = \frac{1}{400} = 0.0025\text{ Hz}

    Correct

    f=1T=1400×10−6 s=2.50×103 Hz=2.50 kHzf = \frac{1}{T} = \frac{1}{400 \times 10^{-6}\text{ s}} = 2.50 \times 10^3\text{ Hz} = 2.50\text{ kHz}

    The unit of hertz (Hz\text{Hz}) is defined as reciprocal seconds (s−1\text{s}^{-1}). Because your period was in microseconds (400 μs400\,\mu\text{s}), you must convert it to 400×10−6 s400 \times 10^{-6}\text{ s} before inverting.

  4. Step 4

    Δϕ=(1.60 div8.00 div)×2π=0.400π rad≈1.26 rad\Delta\phi = \left(\frac{1.60\text{ div}}{8.00\text{ div}}\right) \times 2\pi = 0.400\pi\text{ rad} \approx 1.26\text{ rad}

WHAT YOU DID WELL
Compliments from Your Teacher

You correctly calculated the peak-to-peak voltage and halved it to find the amplitude.

You accurately read the horizontal cycle length and applied the time-base setting to find the period.

You correctly set up the proportional relationship between horizontal division shift and phase angle in radians.

THE ERROR
Where Your ACEpath Teacher Spotted the Mistake
Unit Conversion Error with Metric Prefixes

You substituted 400400 directly into f=1Tf = \frac{1}{T} as if the period were in seconds, forgetting that TT was in microseconds (400 μs400\,\mu\text{s}).

WHY IT HAPPENED
ACEpath Teacher's Diagnosis

Conflating metric-prefixed units (like μs\mu\text{s}) with base SI units (s\text{s}) when applying standard physics formulas that yield SI derived units (Hz=s−1\text{Hz} = \text{s}^{-1}).

REASONING PATH
Your ACEpath teacher’s suggested approach
SI Unit Compatibility Check
  • The unit of frequency is 1 Hz=1 s−11\text{ Hz} = 1\text{ s}^{-1}. Any time interval must be expressed in seconds (s\text{s}) before applying f=1Tf = \frac{1}{T}.

  • Always replace the micro prefix with ×10−6\times 10^{-6} (e.g., 400 μs=400×10−6 s400\,\mu\text{s} = 400 \times 10^{-6}\text{ s}) before calculating the reciprocal.

CORRECTED PATH
ACEpath Teacher's Demonstration
  1. T=400 μs=400×10−6 s=4.00×10−4 sT = 400\,\mu\text{s} = 400 \times 10^{-6}\text{ s} = 4.00 \times 10^{-4}\text{ s}

  2. f=1T=14.00×10−4 s=2.50×103 Hz=2.50 kHzf = \frac{1}{T} = \frac{1}{4.00 \times 10^{-4}\text{ s}} = 2.50 \times 10^3\text{ Hz} = 2.50\text{ kHz}

Final answer

(a) A=1.60 VA = 1.60\text{ V}; (b) T=400 μs=4.00×10−4 sT = 400\,\mu\text{s} = 4.00 \times 10^{-4}\text{ s}, f=2.50 kHzf = 2.50\text{ kHz}; (c) Δϕ=0.400π rad≈1.26 rad\Delta\phi = 0.400\pi\text{ rad} \approx 1.26\text{ rad}

NEXT STEPS
Final Takeaways from Your Teacher
  • Write out metric prefixes as explicit powers of 1010 right after reading values from oscilloscope scale settings.

  • Double-check that your frequency unit matches the time unit: 1μs=MHz\frac{1}{\mu\text{s}} = \text{MHz}, whereas 1s=Hz\frac{1}{\text{s}} = \text{Hz}.

OverviewACEpath Teacher's Diagnosis

03 The student calculates the phase angle in degrees instead of the requested radians.

Sample Student Work

Reviewed by ACEpath Teacher
Step-by-Step Review
Walk Through It with Your Teacher
Partially correct
  1. Step 1

    Vpp=6.40 div×0.500 V/div=3.20 V  ⟹  A=3.20 V2=1.60 VV_{\text{pp}} = 6.40\text{ div} \times 0.500\text{ V/div} = 3.20\text{ V} \implies A = \frac{3.20\text{ V}}{2} = 1.60\text{ V}

  2. Step 2

    T=8.00 div×50.0 μs/div=400 μs=4.00×10−4 s  ⟹  f=1T=14.00×10−4 s=2500 HzT = 8.00\text{ div} \times 50.0\,\mu\text{s/div} = 400\,\mu\text{s} = 4.00 \times 10^{-4}\text{ s} \implies f = \frac{1}{T} = \frac{1}{4.00 \times 10^{-4}\text{ s}} = 2500\text{ Hz}

  3. Step 3

    Δϕ=1.60 div8.00 div×360∘=72∘\Delta\phi = \frac{1.60\text{ div}}{8.00\text{ div}} \times 360^\circ = 72^\circ

    Correct

    Δϕ=2π×1.60 div8.00 div=0.400π rad≈1.26 rad\Delta\phi = 2\pi \times \frac{1.60\text{ div}}{8.00\text{ div}} = 0.400\pi\text{ rad} \approx 1.26\text{ rad}

    Your fractional division ratio 1.608.00=0.200\frac{1.60}{8.00} = 0.200 is correct, but multiplying by 360∘360^\circ yields degrees. The question specifically asked for the phase lag in radians, which requires multiplying by 2π rad2\pi\text{ rad} (or converting 72∘×π180∘72^\circ \times \frac{\pi}{180^\circ}).

WHAT YOU DID WELL
Compliments from Your Teacher

You correctly distinguished peak-to-peak voltage from amplitude and calculated A=1.60 VA = 1.60\text{ V}.

You accurately converted horizontal divisions to period in seconds and correctly computed the frequency as 2500 Hz2500\text{ Hz}.

You correctly identified the proportional relationship between horizontal shift and cycle fraction for the phase difference.

THE ERROR
Where Your ACEpath Teacher Spotted the Mistake
Unit mismatch in phase angle

You solved for the phase angle in degrees (72∘72^\circ) instead of converting to or calculating in radians (1.26 rad1.26\text{ rad}).

WHY IT HAPPENED
ACEpath Teacher's Diagnosis

Defaulting to full-circle degrees (360∘360^\circ) rather than angular radians (2π rad2\pi\text{ rad}) when converting a fractional cycle offset into phase.

REASONING PATH
Your ACEpath teacher’s suggested approach
Oscilloscope Phase Formula
  • One complete horizontal cycle (XTX_T) equals 2π rad2\pi\text{ rad} or 360∘360^\circ. In radians, Δϕ=2π(ΔxXT)\Delta\phi = 2\pi \left(\frac{\Delta x}{X_T}\right).

  • Always check the target unit in the prompt before multiplying by either 360∘360^\circ (degrees) or 2π2\pi (radians).

CORRECTED PATH
ACEpath Teacher's Demonstration
  1. Convert 72∘72^\circ to radians by multiplying by π rad180∘\frac{\pi\text{ rad}}{180^\circ}:

  2. Δϕ=72∘×π rad180∘=72180π rad=0.400π rad\Delta\phi = 72^\circ \times \frac{\pi\text{ rad}}{180^\circ} = \frac{72}{180}\pi\text{ rad} = 0.400\pi\text{ rad}

  3. Evaluate the decimal value: 0.400π≈1.26 rad0.400\pi \approx 1.26\text{ rad}.

Final answer

Δϕ=0.400π rad≈1.26 rad\Delta\phi = 0.400\pi\text{ rad} \approx 1.26\text{ rad}

NEXT STEPS
Final Takeaways from Your Teacher
  • Underline the required unit of measurement in problem prompts (e.g., radians vs. degrees).

  • Practice converting cycle fractions directly into radians using Δϕ=2π⋅ΔtT\Delta\phi = 2\pi \cdot \frac{\Delta t}{T}.

Lock it in

Similar question

01

A sinusoidal signal on an oscilloscope has a vertical peak-to-trough height of 5.20 divisions5.20\text{ divisions}. The vertical scale is set to 0.200 V/div0.200\text{ V/div}. Determine the amplitude AA of the signal in volts.

Answer

A=0.520 VA = 0.520\text{ V}. First, calculate peak-to-peak voltage: Vpp=5.20 div×0.200 V/div=1.04 VV_{\text{pp}} = 5.20\text{ div} \times 0.200\text{ V/div} = 1.04\text{ V}. Then divide by 2 to find amplitude: A=1.04 V2=0.520 VA = \frac{1.04\text{ V}}{2} = 0.520\text{ V}.

02

An oscilloscope displays an AC voltage with a peak-to-peak deflection of 4.80 divisions4.80\text{ divisions} at 1.50 V/div1.50\text{ V/div}, and one cycle occupies 6.00 horizontal divisions6.00\text{ horizontal divisions} at a time-base of 20.0 μs/div20.0\,\mu\text{s/div}. Find (a) the amplitude AA and (b) the angular frequency ω\omega in rad/s\text{rad/s}.

Answer

(a) A=3.60 VA = 3.60\text{ V}; (b) ω=5.24×104 rad/s\omega = 5.24 \times 10^4\text{ rad/s}. Key steps: Vpp=4.80×1.50 V=7.20 V  ⟹  A=7.20 V2=3.60 VV_{\text{pp}} = 4.80 \times 1.50\text{ V} = 7.20\text{ V} \implies A = \frac{7.20\text{ V}}{2} = 3.60\text{ V}. The period is T=6.00×20.0 μs=120 μs=1.20×10−4 sT = 6.00 \times 20.0\,\mu\text{s} = 120\,\mu\text{s} = 1.20 \times 10^{-4}\text{ s}. Then ω=2πT=2π1.20×10−4 s≈5.24×104 rad/s\omega = \frac{2\pi}{T} = \frac{2\pi}{1.20 \times 10^{-4}\text{ s}} \approx 5.24 \times 10^4\text{ rad/s}.

03

Two sinusoidal waves displayed on an oscilloscope screen have the same frequency. One full cycle occupies 10.0 divisions10.0\text{ divisions}. Signal 1 has a peak-to-peak deflection of 5.00 divisions5.00\text{ divisions} at 2.00 V/div2.00\text{ V/div}. Signal 2 reaches its crest 2.50 divisions2.50\text{ divisions} before Signal 1. Determine: (a) the amplitude of Signal 1, and (b) the phase lead of Signal 2 relative to Signal 1 in radians.

Answer

(a) A1=5.00 VA_1 = 5.00\text{ V}; (b) Δϕ=π2 rad≈1.57 rad\Delta\phi = \frac{\pi}{2}\text{ rad} \approx 1.57\text{ rad}. Key steps: Vpp,1=5.00 div×2.00 V/div=10.0 VV_{\text{pp}, 1} = 5.00\text{ div} \times 2.00\text{ V/div} = 10.0\text{ V}, so A1=10.0 V2=5.00 VA_1 = \frac{10.0\text{ V}}{2} = 5.00\text{ V}. The phase lead is Δϕ=(ΔxXT)2π=(2.50 div10.0 div)2π=0.500π rad=π2 rad\Delta\phi = \left(\frac{\Delta x}{X_T}\right) 2\pi = \left(\frac{2.50\text{ div}}{10.0\text{ div}}\right) 2\pi = 0.500\pi\text{ rad} = \frac{\pi}{2}\text{ rad}.

Loading workspace…