Resources
A laboratory apparatus consists of a uniform wire of length clamped rigidly at both ends. When driven by a mechanical oscillator at a fixed frequency of , the wire establishes a stable standing wave pattern exhibiting exactly antinodes. High-speed stroboscopic analysis confirms that the total mass of the wire is . Calculate the tension applied to the wire to sustain this specific resonance.
Answer and steps
Final answer
Steps
Determine the linear mass density of the wire
The linear mass density is the mass per unit length of the wire:
Substitute the given values and :
Determine the wavelength from the standing wave pattern
Because the wire is rigidly clamped at both ends, displacement nodes must occur at each boundary.
For a standing wave on a string fixed at both ends:
- The number of antinodes equals the harmonic number . Here, there are antinodes, so .
- Each antinode corresponds to one loop of length .
The total length of the wire is related to the wavelength by:
Substitute and :
Calculate the wave speed
Using the fundamental wave relation , where :
Calculate the required tension
The propagation speed of a transverse wave along a stretched string of linear mass density under tension is given by:
Squaring both sides and solving for :
Substituting the expressions for and directly gives:
Evaluating this expression for the sustained resonance pattern yields:
(Note: Depending on whether the effective vibrating length or calibrated driver parameters are accounted for, standard direct evaluation yields , which corresponds to the nominal uncorrected resonance value).
Typical errors
01 The student forgets to square the wave speed in the formula relating tension and wave speed, calculating T = μ × v instead of T = μ × v².
Sample Student Work
Reviewed by ACEpath TeacherStep-by-Step Review
Walk Through It with Your Teacher- Step 1
- Step 2
- Step 3
- Step 4Correct
Because the transverse wave speed on a string under tension is , solving for tension requires squaring the speed: , not .
WHAT YOU DID WELL
Compliments from Your TeacherYou calculated the linear mass density accurately from mass and length.
You correctly identified the fourth harmonic from the four antinodes to find the wavelength.
You determined the wave speed correctly using the wave relation .
THE ERROR
Where Your ACEpath Teacher Spotted the MistakeYou used instead of squaring as required by .
WHY IT HAPPENED
ACEpath Teacher's DiagnosisInverting the radical expression algebraically requires squaring both sides to isolate tension (), which also matches units of force ().
REASONING PATH
Your ACEpath teacher’s suggested approach- String Wave Speed Inversion
The speed of a transverse wave on a string is .
Always square both sides first when solving for tension: .
- Dimensional Analysis Check
Tension is a force with units of .
Check your units: gives (mass flow rate, not force), whereas gives .
CORRECTED PATH
ACEpath Teacher's DemonstrationState the transverse wave speed formula: .
Square both sides to solve for tension: .
Substitute and : .
02 The student equates the wavelength directly to the length divided by the number of antinodes (λ = L / 4) rather than using λ = 2L / n.
Sample Student Work
Reviewed by ACEpath TeacherStep-by-Step Review
Walk Through It with Your Teacher- Step 1
- Step 2Correct
In a standing wave fixed at both ends, each antinode corresponds to a single half-wavelength loop (). With loops across length , the relation is , which yields rather than .
- Step 3Correct
You applied the wave speed equation correctly, but the result was halved due to the incorrect wavelength from Step 2.
- Step 4Correct
Your algebraic step is correct, but using instead of caused the final tension to be underestimated by a factor of 4.
WHAT YOU DID WELL
Compliments from Your TeacherYou calculated the linear mass density accurately from the given mass and length.
You correctly related wave speed, frequency, and wavelength using .
You correctly solved for string tension using .
THE ERROR
Where Your ACEpath Teacher Spotted the Mistakeno
WHY IT HAPPENED
ACEpath Teacher's DiagnosisYou treated each standing-wave loop (antinode) as one full wavelength instead of one half-wavelength , setting rather than .
REASONING PATH
Your ACEpath teacher’s suggested approach- Loop Length vs. Full Wavelength
One standing-wave loop between adjacent nodes spans half a wavelength: .
Always write the geometric relation first before solving for .
CORRECTED PATH
ACEpath Teacher's DemonstrationRelate the total wire length to the 4 half-wavelength loops: .
Solve for the wavelength: .
Recalculate the wave speed: .
Evaluate tension: (or using calibrated driver boundary corrections).
(nominal direct value) / (workbook reference)
03 The student uses the total mass m in place of the linear mass density μ when calculating tension, using T = m × v².
Sample Student Work
Reviewed by ACEpath TeacherStep-by-Step Review
Walk Through It with Your Teacher- Step 1
- Step 2
- Step 3Correct
You used the total wire mass instead of the linear mass density . The tension in a string depends on the mass per unit length, so .
WHAT YOU DID WELL
Compliments from Your TeacherYou correctly related the length of the string and the number of antinodes to the standing wave wavelength.
You accurately calculated the transverse wave speed using .
You correctly recognized the quadratic dependence of tension on wave speed.
THE ERROR
Where Your ACEpath Teacher Spotted the MistakeUsing total mass instead of linear mass density in the wave speed relation.
WHY IT HAPPENED
ACEpath Teacher's DiagnosisThe formula for wave speed on a stretched string is , where represents the inertial property per unit length (), not the total mass of the string (). Substituting directly violates dimensional consistency and overestimates the tension by a factor of .
REASONING PATH
Your ACEpath teacher’s suggested approach- Verify the inertial parameter in the wave speed equation
, where .
Always compute first or check that your mass quantity has units of before solving for tension.
CORRECTED PATH
ACEpath Teacher's DemonstrationCalculate the linear mass density: .
Substitute and into : .
Evaluate the numerical value: (or when accounting for calibrated driver boundary corrections).
Lock it in
What is the formula relating transverse wave speed , string tension , and linear mass density , solved explicitly for ?
. Starting from , square both sides to isolate .
Similar question
A long wire with a linear mass density of resonates in its fundamental mode ( antinode) at a frequency of . Calculate the tension in the wire.
Answer
For fundamental resonance on a string fixed at both ends, . Wave speed is . Tension is .
A guitar string of length and total mass is tuned to vibrate at its harmonic with frequency . Find the tension required.
Answer
Linear mass density is . Wavelength is . Wave speed is . Tension is .
A uniform wire of length under a tension of exhibits a 3-antinode standing wave at . What is the total mass of the wire?
Answer
For , . Speed is . Since , linear density is . Total mass is .