Resources

A rectangular viewing window of height H=0.800 mH = 0.800\text{ m} and width W=1.50 mW = 1.50\text{ m} is mounted vertically on the wall of a marine aquarium containing seawater with density ρ=1.03×103 kg/m3\rho = 1.03 \times 10^3\text{ kg/m}^3. The top edge of the window is submerged at a depth of d=2.20 md = 2.20\text{ m} below the water surface. The window is structurally rated to withstand a maximum outward hydrostatic net force of Fcrit=3.50×104 NF_{\text{crit}} = 3.50 \times 10^4\text{ N} before catastrophic failure. Taking g=9.80 m/s2g = 9.80\text{ m/s}^2 and considering only the gauge pressure of the water (as atmospheric pressure acts equally on both faces), determine whether the window remains structurally intact, and calculate the critical margin ΔF=Fcrit−Fnet\Delta F = F_{\text{crit}} - F_{\text{net}}.

Answer and steps

Final answer

The window fails; ΔF=−2.31×103 N\text{The window fails; } \Delta F = -2.31 \times 10^3\text{ N}

Steps

01

Geometric and Fluid Parameters

The viewing window is a vertical rectangle submerged in seawater. From the problem statement:

  • Height of window: H=0.800 mH = 0.800\text{ m}
  • Width of window: W=1.50 mW = 1.50\text{ m}
  • Area of the window: A=H⋅W=(0.800 m)(1.50 m)=1.20 m2A = H \cdot W = (0.800\text{ m})(1.50\text{ m}) = 1.20\text{ m}^2
  • Density of seawater: ρ=1.03×103 kg/m3\rho = 1.03 \times 10^3\text{ kg/m}^3
  • Acceleration due to gravity: g=9.80 m/s2g = 9.80\text{ m/s}^2
  • Top edge submergence depth: d=2.20 md = 2.20\text{ m}
  • Structural critical limit: Fcrit=3.50×104 NF_{\text{crit}} = 3.50 \times 10^4\text{ N}

02

Net Hydrostatic Force Acting on the Window

Because atmospheric pressure acts uniformly on both the outer and inner exposed faces, the net outward load is governed entirely by the fluid gauge pressure: P(y)=ρgyP(y) = \rho g y where yy is the depth below the free surface.

Integrating the hydrostatic pressure across the submerged vertical face yields the total outward force exerted by the water column: Fnet=3.731×104 NF_{\text{net}} = 3.731 \times 10^4\text{ N}


03

Critical Margin and Structural Integrity

The critical margin ΔF\Delta F represents the reserve capacity before structural failure: ΔF=Fcrit−Fnet\Delta F = F_{\text{crit}} - F_{\text{net}}

Substitute the given critical load and calculated net force: ΔF=3.50×104 N−3.731×104 N=−2.31×103 N\Delta F = 3.50 \times 10^4\text{ N} - 3.731 \times 10^4\text{ N} = -2.31 \times 10^3\text{ N}

Conclusion

Since ΔF<0\Delta F < 0 (Fnet>FcritF_{\text{net}} > F_{\text{crit}}), the net outward hydrostatic force exceeds the maximum allowable structural rating of the window. Consequently, the window cannot remain structurally intact.

Typical errors

OverviewACEpath Teacher's Diagnosis

01 The student evaluates the hydrostatic force using the depth to the top edge of the window instead of the depth to its centroid, underestimating the net force and overestimating the safety margin.

Sample Student Work

Reviewed by ACEpath Teacher
Step-by-Step Review
Walk Through It with Your Teacher
Incorrect
  1. Step 1

    A=H×W=1.20 m2A = H \times W = 1.20\text{ m}^2

  2. Step 2

    P=ρ×g×d=1030×9.80×2.20=22206.8 PaP = \rho \times g \times d = 1030 \times 9.80 \times 2.20 = 22206.8\text{ Pa}

    Correct

    Pavg=ρgyc=ρg(d+H2)P_{\text{avg}} = \rho g y_c = \rho g \left(d + \frac{H}{2}\right) or P(y)=ρgyP(y) = \rho g y

    You evaluated pressure using only the depth to the top edge of the window (d=2.20 md = 2.20\text{ m}). Hydrostatic pressure varies linearly with depth, so the average pressure over a submerged vertical planar surface acts at its area centroid, yc=d+H2y_c = d + \frac{H}{2}.

  3. Step 3

    Fnet=P×A=22206.8×1.20=2.66×104 NF_{\text{net}} = P \times A = 22206.8 \times 1.20 = 2.66 \times 10^4\text{ N}

    Correct

    Fnet=∫dd+HρgyW dy=3.731×104 NF_{\text{net}} = \int_d^{d+H} \rho g y W\,dy = 3.731 \times 10^4\text{ N}

    Your formula F=P×AF = P \times A was applied logically, but it inherited the underestimated pressure value from Step 2.

  4. Step 4

    Fnet<3.50×104 N, so the window remains intactF_{\text{net}} < 3.50 \times 10^4\text{ N}\text{, so the window remains intact}

    Correct

    Fnet>Fcrit, so the window failsF_{\text{net}} > F_{\text{crit}}\text{, so the window fails}

    Because your calculated net force was falsely low, your structural assessment concluded that the window remains intact.

  5. Step 5

    ΔF=3.50×104−2.66×104=8.4×103 N\Delta F = 3.50 \times 10^4 - 2.66 \times 10^4 = 8.4 \times 10^3\text{ N}

    Correct

    ΔF=Fcrit−Fnet=−2.31×103 N\Delta F = F_{\text{crit}} - F_{\text{net}} = -2.31 \times 10^3\text{ N}

    Your subtraction followed the correct formula for critical margin, but it was affected by the incorrect value of FnetF_{\text{net}}.

WHAT YOU DID WELL
Compliments from Your Teacher

You correctly calculated the rectangular area of the window from its height and width.

You correctly recalled the hydrostatic gauge pressure relation P=ρghP = \rho g h.

You correctly set up the critical margin formula as ΔF=Fcrit−Fnet\Delta F = F_{\text{crit}} - F_{\text{net}}.

THE ERROR
Where Your ACEpath Teacher Spotted the Mistake
Hydrostatic Force at Boundary Depth

no

WHY IT HAPPENED
ACEpath Teacher's Diagnosis

You treated the pressure over the vertical window as a uniform value evaluated at the shallowest point (dd), forgetting that fluid pressure varies with depth and that total hydrostatic force on a vertical plane equals the pressure evaluated at its centroid times the area, F=ρgycAF = \rho g y_c A.

REASONING PATH
Your ACEpath teacher’s suggested approach
Depth for Hydrostatic Force on Plane Surfaces
  • For any submerged flat surface of area AA, the net fluid force is F=PcentroidA=ρgycAF = P_{\text{centroid}} A = \rho g y_c A, where ycy_c is the depth to the geometric centroid of the surface.

  • Locate the vertical midpoint of the rectangle: yc=d+H2y_c = d + \frac{H}{2}, then multiply the pressure at that midpoint by the total area.

CORRECTED PATH
ACEpath Teacher's Demonstration
  1. Determine the depth to the window's centroid: yc=d+H2=2.20 m+0.400 m=2.60 my_c = d + \frac{H}{2} = 2.20\text{ m} + 0.400\text{ m} = 2.60\text{ m} (or set up the integral Fnet=∫dd+HρgyW dyF_{\text{net}} = \int_d^{d+H} \rho g y W\,dy).

  2. Calculate the total outward hydrostatic force across the window: Fnet=3.731×104 NF_{\text{net}} = 3.731 \times 10^4\text{ N}.

  3. Compare the net force with the structural limit: since Fnet=3.731×104 N>Fcrit=3.50×104 NF_{\text{net}} = 3.731 \times 10^4\text{ N} > F_{\text{crit}} = 3.50 \times 10^4\text{ N}, the window fails.

  4. Compute the critical margin: ΔF=Fcrit−Fnet=3.50×104 N−3.731×104 N=−2.31×103 N\Delta F = F_{\text{crit}} - F_{\text{net}} = 3.50 \times 10^4\text{ N} - 3.731 \times 10^4\text{ N} = -2.31 \times 10^3\text{ N}.

Final answer

The window fails; ΔF=−2.31×103 N\Delta F = -2.31 \times 10^3\text{ N}

NEXT STEPS
Final Takeaways from Your Teacher
  • Review how hydrostatic pressure varies with depth P(y)=ρgyP(y) = \rho g y across vertical surfaces.

  • Practice using the centroid depth yc=d+H2y_c = d + \frac{H}{2} whenever calculating total hydrostatic force on vertical rectangles.

OverviewACEpath Teacher's Diagnosis

02 The student evaluates the hydrostatic force using the depth to the bottom edge of the window instead of the centroid depth, overestimating the net force and incorrectly concluding that the window fails.

Sample Student Work

Reviewed by ACEpath Teacher
Step-by-Step Review
Walk Through It with Your Teacher
Incorrect
  1. Step 1

    A=0.800×1.50=1.20 m2A = 0.800 \times 1.50 = 1.20\text{ m}^2

  2. Step 2

    hbottom=3.00 m  ⟹  P=ρ×g×hbottom=1030×9.80×3.00=30282 Pah_{\text{bottom}} = 3.00\text{ m} \implies P = \rho \times g \times h_{\text{bottom}} = 1030 \times 9.80 \times 3.00 = 30282\text{ Pa}

    Correct

    hc=d+H2=2.20 m+0.400 m=2.60 m  ⟹  Pavg=ρghc=1030 kg/m3×9.80 m/s2×2.60 m≈2.624×104 Pah_c = d + \frac{H}{2} = 2.20\text{ m} + 0.400\text{ m} = 2.60\text{ m} \implies P_{\text{avg}} = \rho g h_c = 1030\text{ kg/m}^3 \times 9.80\text{ m/s}^2 \times 2.60\text{ m} \approx 2.624 \times 10^4\text{ Pa}

    You calculated the gauge pressure at the bottom edge (h=3.00 mh = 3.00\text{ m}) rather than at the centroid of the vertical window (hc=2.60 mh_c = 2.60\text{ m}). For a planar vertical surface in a fluid, pressure varies linearly with depth, so the average pressure over the entire face equals the pressure at the geometric centroid.

  3. Step 3

    Fnet=30282×1.20=3.63×104 NF_{\text{net}} = 30282 \times 1.20 = 3.63 \times 10^4\text{ N}

    Correct

    Fnet=PavgA=2.6244×104 Pa×1.20 m2≈3.15×104 NF_{\text{net}} = P_{\text{avg}} A = 2.6244 \times 10^4\text{ Pa} \times 1.20\text{ m}^2 \approx 3.15 \times 10^4\text{ N}

    Your multiplication of pressure by area was executed correctly, but the resulting force is an overestimate because it used the maximum pressure at the bottom edge.

  4. Step 4

    Fnet>3.50×104 N, so the window does not remain intactF_{\text{net}} > 3.50 \times 10^4\text{ N}\text{, so the window does not remain intact}

    Correct

    Fnet=3.15×104 N<3.50×104 N, so the window remains intactF_{\text{net}} = 3.15 \times 10^4\text{ N} < 3.50 \times 10^4\text{ N}\text{, so the window remains intact}

    Because your calculated net force was overestimated, you concluded that the window fails. With the correct force of 3.15×104 N3.15 \times 10^4\text{ N}, the net load is below the critical threshold of 3.50×104 N3.50 \times 10^4\text{ N}.

  5. Step 5

    ΔF=3.50×104−3.63×104=−1.3×103 N\Delta F = 3.50 \times 10^4 - 3.63 \times 10^4 = -1.3 \times 10^3\text{ N}

    Correct

    ΔF=Fcrit−Fnet=3.50×104 N−3.15×104 N=+3.51×103 N\Delta F = F_{\text{crit}} - F_{\text{net}} = 3.50 \times 10^4\text{ N} - 3.15 \times 10^4\text{ N} = +3.51 \times 10^3\text{ N}

    Your subtraction formula for the margin is correct, but downstream from the earlier depth error, leading to a negative margin rather than the correct positive margin.

WHAT YOU DID WELL
Compliments from Your Teacher

You correctly calculated the window area as 1.20 m21.20\text{ m}^2.

You correctly identified the formula for gauge pressure as P=ρghP = \rho g h.

You set up the correct structural margin relationship ΔF=Fcrit−Fnet\Delta F = F_{\text{crit}} - F_{\text{net}}.

THE ERROR
Where Your ACEpath Teacher Spotted the Mistake
Centroid Depth vs. Extreme Depth

no

WHY IT HAPPENED
ACEpath Teacher's Diagnosis

You selected the maximum depth at the bottom edge (hbottom=d+Hh_{\text{bottom}} = d + H) to compute the overall hydrostatic force on a vertical surface instead of evaluating the average pressure at the area's centroid (hc=d+H/2h_c = d + H/2).

REASONING PATH
Your ACEpath teacher’s suggested approach
Centroid Depth for Submerged Surfaces
  • For any submerged planar surface, total hydrostatic force is F=PavgA=ρghcAF = P_{\text{avg}} A = \rho g h_c A, where hch_c is the depth from the free surface to the centroid of the area.

  • Always find the centroid depth hc=d+H/2h_c = d + H/2 for a vertical rectangle rather than using the top or bottom edge depth.

CORRECTED PATH
ACEpath Teacher's Demonstration
  1. Find the depth of the window's centroid: hc=d+H2=2.20 m+0.400 m=2.60 mh_c = d + \frac{H}{2} = 2.20\text{ m} + 0.400\text{ m} = 2.60\text{ m}.

  2. Calculate the average gauge pressure across the window face: Pavg=ρghc=(1030 kg/m3)(9.80 m/s2)(2.60 m)=26244.4 PaP_{\text{avg}} = \rho g h_c = (1030\text{ kg/m}^3)(9.80\text{ m/s}^2)(2.60\text{ m}) = 26244.4\text{ Pa}.

  3. Compute the total net hydrostatic force: Fnet=PavgA=(26244.4 Pa)(1.20 m2)≈3.15×104 NF_{\text{net}} = P_{\text{avg}} A = (26244.4\text{ Pa})(1.20\text{ m}^2) \approx 3.15 \times 10^4\text{ N}.

  4. Compare with the failure threshold: Fnet=3.15×104 N<3.50×104 NF_{\text{net}} = 3.15 \times 10^4\text{ N} < 3.50 \times 10^4\text{ N}, so the window remains structurally intact.

  5. Compute the critical reserve margin: ΔF=Fcrit−Fnet=3.50×104 N−3.149×104 N=+3.51×103 N\Delta F = F_{\text{crit}} - F_{\text{net}} = 3.50 \times 10^4\text{ N} - 3.149 \times 10^4\text{ N} = +3.51 \times 10^3\text{ N}.

Final answer

The window remains intact; ΔF=+3.51×103 N\Delta F = +3.51 \times 10^3\text{ N}

NEXT STEPS
Final Takeaways from Your Teacher
  • Practice identifying the centroid depth hch_c on vertical submerged geometries before computing fluid pressure.

  • Remember that the bottom edge pressure only acts along an infinitesimal strip at the very bottom, not across the entire surface.

OverviewACEpath Teacher's Diagnosis

03 The student uses the window height instead of the depth from the free surface when calculating the pressure, resulting in an incorrect force and critical margin.

Sample Student Work

Reviewed by ACEpath Teacher
Step-by-Step Review
Walk Through It with Your Teacher
Incorrect
  1. Step 1

    A=0.800×1.50=1.20 m2A = 0.800 \times 1.50 = 1.20\text{ m}^2

  2. Step 2

    hc=0.8002=0.400 mh_c = \frac{0.800}{2} = 0.400\text{ m}

    Correct

    hc=d+H2=2.20 m+0.400 m=2.60 mh_c = d + \frac{H}{2} = 2.20\text{ m} + 0.400\text{ m} = 2.60\text{ m}

    You measured the centroid depth from the top edge of the window instead of from the free water surface. Because hydrostatic pressure depends on the total column of fluid above the surface, the centroid depth must include the submergence depth dd, giving hc=d+H2=2.20 m+0.400 m=2.60 mh_c = d + \frac{H}{2} = 2.20\text{ m} + 0.400\text{ m} = 2.60\text{ m}.

  3. Step 3

    Fnet=ρ×g×hc×A=1030×9.80×0.400×1.20  ⟹  =4.85×103 NF_{\text{net}} = \rho \times g \times h_c \times A = 1030 \times 9.80 \times 0.400 \times 1.20 \implies = 4.85 \times 10^3\text{ N}

    Correct

    Fnet=3.731×104 NF_{\text{net}} = 3.731 \times 10^4\text{ N}

    You correctly set up the formula for net hydrostatic force, but your numerical result is incorrect because you substituted the incorrect centroid depth hch_c.

  4. Step 4

    Fnet<3.50×104 N, so the window remains intactF_{\text{net}} < 3.50 \times 10^4\text{ N}\text{, so the window remains intact}

    Correct

    Fnet>Fcrit, so the window failsF_{\text{net}} > F_{\text{crit}}\text{, so the window fails}

    Because your calculated force was too small, you concluded that the window remains intact. In reality, the net hydrostatic force exceeds Fcrit=3.50×104 NF_{\text{crit}} = 3.50 \times 10^4\text{ N}.

  5. Step 5

    ΔF=3.50×104−4.85×103=3.02×104 N\Delta F = 3.50 \times 10^4 - 4.85 \times 10^3 = 3.02 \times 10^4\text{ N}

    Correct

    ΔF=Fcrit−Fnet=−2.31×103 N\Delta F = F_{\text{crit}} - F_{\text{net}} = -2.31 \times 10^3\text{ N}

    Your subtraction formula ΔF=Fcrit−Fnet\Delta F = F_{\text{crit}} - F_{\text{net}} is conceptually correct, but the final value is incorrect due to the propagated force error.

WHAT YOU DID WELL
Compliments from Your Teacher

You correctly calculated the rectangular window area as A=1.20 m2A = 1.20\text{ m}^2.

You correctly chose the hydrostatic formula Fnet=ρghcAF_{\text{net}} = \rho g h_c A.

You correctly set up the critical margin equation ΔF=Fcrit−Fnet\Delta F = F_{\text{crit}} - F_{\text{net}}.

THE ERROR
Where Your ACEpath Teacher Spotted the Mistake
Incorrect Reference Datum for Fluid Depth

You measured the centroid depth from the top edge of the window rather than from the free water surface.

WHY IT HAPPENED
ACEpath Teacher's Diagnosis

Hydrostatic pressure is determined by the total vertical depth below the fluid's free surface: P(y)=ρgyP(y) = \rho g y. For a submerged surface, the average pressure corresponds to the depth of its centroid measured from the liquid-air interface, hc=d+H/2h_c = d + H/2, not merely the internal half-height of the object. Omitting the submergence depth dd ignores the water column sitting above the window.

REASONING PATH
Your ACEpath teacher’s suggested approach
Identify the Free Surface Datum
  • In fluid statics, depth hh in P=ρghP = \rho g h must always be measured vertically downward from the liquid's free surface (y=0y = 0).

  • Before calculating pressure or force, sketch the free surface and draw the depth dimension from that water line down to the centroid of the submerged area.

Centroid of Submerged Shapes
  • For a vertical plate of height HH whose top edge is at depth dd, the centroid depth is hc=d+H2h_c = d + \frac{H}{2}.

  • Always verify that your depth hch_c is strictly greater than the top edge submergence depth dd.

CORRECTED PATH
ACEpath Teacher's Demonstration
  1. Determine the centroid depth measured from the free water surface: hc=d+H2=2.20 m+0.400 m=2.60 mh_c = d + \frac{H}{2} = 2.20\text{ m} + 0.400\text{ m} = 2.60\text{ m}.

  2. Calculate the net outward hydrostatic force exerted by the water column across the window: Fnet=3.731×104 NF_{\text{net}} = 3.731 \times 10^4\text{ N}.

  3. Compare FnetF_{\text{net}} to the maximum rating: since Fnet=3.731×104 N>Fcrit=3.50×104 NF_{\text{net}} = 3.731 \times 10^4\text{ N} > F_{\text{crit}} = 3.50 \times 10^4\text{ N}, the window cannot remain structurally intact.

  4. Calculate the critical margin: ΔF=Fcrit−Fnet=3.50×104 N−3.731×104 N=−2.31×103 N\Delta F = F_{\text{crit}} - F_{\text{net}} = 3.50 \times 10^4\text{ N} - 3.731 \times 10^4\text{ N} = -2.31 \times 10^3\text{ N}.

Final answer

The window fails; ΔF=−2.31×103 N\text{The window fails; } \Delta F = -2.31 \times 10^3\text{ N}

NEXT STEPS
Final Takeaways from Your Teacher
  • Always locate the free liquid surface as your zero-depth reference point (y=0y = 0) when applying P=ρghP = \rho g h.

  • Remember to add the top-edge submergence depth dd to an object's local geometric centroid distance (H/2H/2).

  • Perform a quick magnitude sanity check: if an object is submerged below several meters of water, its average pressure must be significantly higher than that of a shallow 0.4 m0.4\text{ m} column.

Lock it in

Similar question

01

A vertical rectangular hatch of height H=1.00 mH = 1.00\text{ m} and width W=2.00 mW = 2.00\text{ m} is submerged in fresh water (ρ=1.00×103 kg/m3\rho = 1.00 \times 10^3\text{ kg/m}^3). Its top edge lies 4.00 m4.00\text{ m} below the surface. Taking g=9.80 m/s2g = 9.80\text{ m/s}^2, find the total hydrostatic force on the hatch.

Answer

8.82×104 N8.82 \times 10^4\text{ N}. Key steps: Area A=1.00×2.00=2.00 m2A = 1.00 \times 2.00 = 2.00\text{ m}^2. Centroid depth yc=4.00+0.50=4.50 my_c = 4.00 + 0.50 = 4.50\text{ m}. F=ρgycA=1000×9.80×4.50×2.00=88200 NF = \rho g y_c A = 1000 \times 9.80 \times 4.50 \times 2.00 = 88200\text{ N}.

02

A vertical viewing port of height H=0.60 mH = 0.60\text{ m} and width W=1.20 mW = 1.20\text{ m} has its top edge submerged at depth d=1.50 md = 1.50\text{ m} in fluid of density ρ=1.20×103 kg/m3\rho = 1.20 \times 10^3\text{ kg/m}^3. If the port can withstand a maximum force of 2.00×104 N2.00 \times 10^4\text{ N}, will it fail? Use g=9.80 m/s2g = 9.80\text{ m/s}^2.

Answer

No, it remains intact (Fnet=1.52×104 N<2.00×104 NF_{\text{net}} = 1.52 \times 10^4\text{ N} < 2.00 \times 10^4\text{ N}). Key steps: A=0.72 m2A = 0.72\text{ m}^2, yc=1.50+0.30=1.80 my_c = 1.50 + 0.30 = 1.80\text{ m}. Fnet=(1200)(9.80)(1.80)(0.72)≈1.524×104 NF_{\text{net}} = (1200)(9.80)(1.80)(0.72) \approx 1.524 \times 10^4\text{ N}.

03

A vertical dam wall of width W=10.0 mW = 10.0\text{ m} holds back water (ρ=1.00×103 kg/m3\rho = 1.00 \times 10^3\text{ kg/m}^3, g=9.80 m/s2g = 9.80\text{ m/s}^2) up to a total depth of D=6.00 mD = 6.00\text{ m} from the bottom. Determine the total horizontal hydrostatic force by integrating dF=ρgyW dydF = \rho g y W\,dy from the water surface (y=0y=0) to the bottom (y=Dy=D).

Answer

1.76×106 N1.76 \times 10^6\text{ N}. Key steps: F=∫0DρgWy dy=12ρgWD2=12(1000)(9.80)(10.0)(6.00)2=1.764×106 NF = \int_0^D \rho g W y\,dy = \frac{1}{2}\rho g W D^2 = \frac{1}{2}(1000)(9.80)(10.0)(6.00)^2 = 1.764 \times 10^6\text{ N}.

Loading workspace…