Resources

A specialized hydraulic lift operates with an output piston of diameter D2=32.0 cmD_2 = 32.0\text{ cm} designed to elevate heavy crates. When a mechanical actuator applies an input force of F1=78.0 NF_1 = 78.0\text{ N} to an input cylinder of diameter D1=4.00 cmD_1 = 4.00\text{ cm}, the system successfully holds a crate of mass mm at rest on the output platform, where both pistons remain at the same level. Assuming the fluid is incompressible and the pistons have negligible weight, determine the mass mm of the crate supported in equilibrium (take g=9.80 m/s2g = 9.80\text{ m/s}^2).

Answer and steps

Final answer

m=509 kgm = 509\text{ kg}

Steps

01

Apply Pascal's Principle

Pascal's principle states that a pressure applied to an enclosed, incompressible fluid is transmitted undiminished to every portion of the fluid and the walls of its container.

Because both pistons remain at the same horizontal level, the hydrostatic pressure is identical at both piston surfaces:

P1=P2P_1 = P_2

Expressing pressure as force per unit area (P=FAP = \frac{F}{A}):

F1A1=F2A2\frac{F_1}{A_1} = \frac{F_2}{A_2}

where:

  • F1F_1 is the input force applied to the smaller cylinder.
  • A1A_1 is the cross-sectional area of the smaller cylinder.
  • F2F_2 is the upward force exerted by the fluid on the output piston.
  • A2A_2 is the cross-sectional area of the larger output piston.

02

Relate Force to Diameter

The cross-sectional area of a circular piston of diameter DD is A=πD24A = \frac{\pi D^2}{4}. Substituting this into the force balance equation:

F1πD124=F2πD224\frac{F_1}{\frac{\pi D_1^2}{4}} = \frac{F_2}{\frac{\pi D_2^2}{4}}

Simplifying by canceling the common factor π4\frac{\pi}{4}:

F1D12=F2D22  ⟹  F2=F1(D2D1)2\frac{F_1}{D_1^2} = \frac{F_2}{D_2^2} \implies F_2 = F_1 \left(\frac{D_2}{D_1}\right)^2

Common Pitfall: Be careful to square the ratio of the diameters. A frequent mistake is taking the linear ratio D2D1\frac{D_2}{D_1} instead of the area ratio (D2D1)2\left(\frac{D_2}{D_1}\right)^2, which underestimates the output force.


03

Calculate the Output Force F2F_2

Substitute the given values into the formula:

  • D1=4.00 cmD_1 = 4.00\text{ cm}
  • D2=32.0 cmD_2 = 32.0\text{ cm}
  • F1=78.0 NF_1 = 78.0\text{ N}

D2D1=32.0 cm4.00 cm=8.00\frac{D_2}{D_1} = \frac{32.0\text{ cm}}{4.00\text{ cm}} = 8.00

F2=78.0 N⋅(8.00)2=78.0 N⋅64.0=4992 NF_2 = 78.0\text{ N} \cdot (8.00)^2 = 78.0\text{ N} \cdot 64.0 = 4992\text{ N}


04

Determine the Mass of the Supported Crate

At equilibrium, the upward force F2F_2 exerted by the fluid balances the weight of the crate, W=mgW = mg:

F2=mg  ⟹  m=F2gF_2 = mg \implies m = \frac{F_2}{g}

Using g=9.80 m/s2g = 9.80\text{ m/s}^2:

m=4992 N9.80 m/s2≈509.39 kgm = \frac{4992\text{ N}}{9.80\text{ m/s}^2} \approx 509.39\text{ kg}

Rounding to three significant figures gives:

m=509 kgm = 509\text{ kg}

Typical errors

OverviewACEpath Teacher's Diagnosis

01 The student scales the force linearly with the diameter ratio instead of the area ratio (diameter squared), resulting in an underestimated mass of 63.7 kg.

Sample Student Work

Reviewed by ACEpath Teacher
Step-by-Step Review
Walk Through It with Your Teacher
Incorrect
  1. Step 1

    F2F1=D2D1  ⟹  F2=78.0×32.04.00=624 N\frac{F_2}{F_1} = \frac{D_2}{D_1} \implies F_2 = 78.0 \times \frac{32.0}{4.00} = 624\text{ N}

    Correct

    F2F1=A2A1=(D2D1)2  ⟹  F2=78.0×(32.04.00)2=4992 N\frac{F_2}{F_1} = \frac{A_2}{A_1} = \left(\frac{D_2}{D_1}\right)^2 \implies F_2 = 78.0 \times \left(\frac{32.0}{4.00}\right)^2 = 4992\text{ N}

    Pressure transmitted through the fluid is force per unit area (P=FAP = \frac{F}{A}). Because the cross-sectional area of a circular piston is proportional to the square of its diameter (A=πD24A = \frac{\pi D^2}{4}), the force ratio equals (D2D1)2\left(\frac{D_2}{D_1}\right)^2, not D2D1\frac{D_2}{D_1}.

  2. Step 2

    m=F2g=6249.80=63.7 kgm = \frac{F_2}{g} = \frac{624}{9.80} = 63.7\text{ kg}

    Correct

    m=F2g=49929.80≈509 kgm = \frac{F_2}{g} = \frac{4992}{9.80} \approx 509\text{ kg}

    Your relationship between weight and mass is correct, but using the incorrect force value from step 1 led to an underestimated mass.

WHAT YOU DID WELL
Compliments from Your Teacher

You correctly equated the upward output force to the weight of the supported mass (F2=mgF_2 = mg).

You accurately substituted your calculated force and the gravitational acceleration into m=F2gm = \frac{F_2}{g}.

THE ERROR
Where Your ACEpath Teacher Spotted the Mistake
Linear scaling error instead of area scaling

no

WHY IT HAPPENED
ACEpath Teacher's Diagnosis

You equated the force ratio directly to the linear ratio of the piston diameters (D2D1\frac{D_2}{D_1}) instead of the ratio of their cross-sectional areas (A2A1=(D2D1)2\frac{A_2}{A_1} = \left(\frac{D_2}{D_1}\right)^2).

REASONING PATH
Your ACEpath teacher’s suggested approach
Pascal's Principle Ratio Check
  • Hydraulic force scales with cross-sectional area: F2F1=A2A1=(D2D1)2\frac{F_2}{F_1} = \frac{A_2}{A_1} = \left(\frac{D_2}{D_1}\right)^2.

  • Always write P1=P2  ⟹  F1A1=F2A2P_1 = P_2 \implies \frac{F_1}{A_1} = \frac{F_2}{A_2} first, then express area in terms of diameter squared before solving for force.

CORRECTED PATH
ACEpath Teacher's Demonstration
  1. Apply Pascal's principle in terms of piston areas: F2F1=A2A1=(D2D1)2\frac{F_2}{F_1} = \frac{A_2}{A_1} = \left(\frac{D_2}{D_1}\right)^2

  2. Substitute the given values: F2=78.0 N×(32.0 cm4.00 cm)2=78.0 N×64=4992 NF_2 = 78.0\text{ N} \times \left(\frac{32.0\text{ cm}}{4.00\text{ cm}}\right)^2 = 78.0\text{ N} \times 64 = 4992\text{ N}

  3. Calculate the crate mass in equilibrium: m=F2g=4992 N9.80 m/s2≈509 kgm = \frac{F_2}{g} = \frac{4992\text{ N}}{9.80\text{ m/s}^2} \approx 509\text{ kg}

Final answer

m=509 kgm = 509\text{ kg}

NEXT STEPS
Final Takeaways from Your Teacher
  • When working with hydraulic systems, write the pressure balance F1A1=F2A2\frac{F_1}{A_1} = \frac{F_2}{A_2} explicitly before replacing area with diameter.

  • Remember that area scales quadratically with linear dimensions: doubling the diameter quadruples the cross-sectional area and the transmitted force.

OverviewACEpath Teacher's Diagnosis

02 The student solves for the upward force exerted by the output piston correctly but forgets to divide by gravitational acceleration g, conflating weight in newtons with mass in kilograms.

Sample Student Work

Reviewed by ACEpath Teacher
Step-by-Step Review
Walk Through It with Your Teacher
Incorrect
  1. Step 1

    F2=F1×(D2D1)2  ⟹  F2=78.0×(32.04.00)2=78.0×64=4992 NF_2 = F_1 \times \left(\frac{D_2}{D_1}\right)^2 \implies F_2 = 78.0 \times \left(\frac{32.0}{4.00}\right)^2 = 78.0 \times 64 = 4992\text{ N}

  2. Step 2

    m=4992 kgm = 4992\text{ kg}

    Correct

    m=F2g=4992 N9.80 m/s2≈509 kgm = \frac{F_2}{g} = \frac{4992\text{ N}}{9.80\text{ m/s}^2} \approx 509\text{ kg}

    You set the mass equal to the numerical value of the force. Because the upward fluid force supports the crate's weight (F2=mgF_2 = mg), you need to divide the force by g=9.80 m/s2g = 9.80\text{ m/s}^2 to find the mass.

WHAT YOU DID WELL
Compliments from Your Teacher

You correctly used Pascal's principle to relate the forces and piston diameters.

You accurately computed the force ratio and obtained the correct upward force of 4992 N4992\text{ N}.

THE ERROR
Where Your ACEpath Teacher Spotted the Mistake
Conflating Weight and Mass

no

WHY IT HAPPENED
ACEpath Teacher's Diagnosis

You treated the output force (measured in newtons) as equal to the crate's mass (measured in kilograms), skipping the gravitational conversion W=mgW = mg.

REASONING PATH
Your ACEpath teacher’s suggested approach
Distinguish Force from Mass
  • Weight is a downward gravitational force given by W=mgW = mg, measured in newtons (N\text{N}), whereas mass mm is measured in kilograms (kg\text{kg}).

  • Whenever an equilibrium problem asks for mass from a supporting force, divide the upward force by gg (m=Fgm = \frac{F}{g}).

CORRECTED PATH
ACEpath Teacher's Demonstration
  1. Equate the upward hydraulic force to the gravitational weight: F2=mgF_2 = mg.

  2. Solve for mass: m=F2g=4992 N9.80 m/s2≈509.39 kgm = \frac{F_2}{g} = \frac{4992\text{ N}}{9.80\text{ m/s}^2} \approx 509.39\text{ kg}.

  3. Round to three significant figures.

Final answer

m=509 kgm = 509\text{ kg}

NEXT STEPS
Final Takeaways from Your Teacher
  • Always write down the equilibrium condition Fnet=0  ⟹  F2=mgF_{\text{net}} = 0 \implies F_2 = mg before stating the mass.

  • Check that your units balance: N/(m/s2)=kg\text{N} / (\text{m/s}^2) = \text{kg}, ensuring force is not directly substituted as mass.

OverviewACEpath Teacher's Diagnosis

03 The student inverts the diameter ratio when applying Pascal's principle, calculating that the output force is smaller than the input force.

Sample Student Work

Reviewed by ACEpath Teacher
Step-by-Step Review
Walk Through It with Your Teacher
Incorrect
  1. Step 1

    F2=F1×(D1D2)2  ⟹  F2=78.0×(4.0032.0)2=1.21875 NF_2 = F_1 \times \left(\frac{D_1}{D_2}\right)^2 \implies F_2 = 78.0 \times \left(\frac{4.00}{32.0}\right)^2 = 1.21875\text{ N}

    Correct

    F2=F1×(D2D1)2=78.0 N×(32.0 cm4.00 cm)2=4992 NF_2 = F_1 \times \left(\frac{D_2}{D_1}\right)^2 = 78.0\text{ N} \times \left(\frac{32.0\text{ cm}}{4.00\text{ cm}}\right)^2 = 4992\text{ N}

    Pascal's principle requires equal pressure at the same fluid level: F1A1=F2A2\frac{F_1}{A_1} = \frac{F_2}{A_2}. Solving for the output force gives F2=F1(A2A1)=F1(D2D1)2F_2 = F_1\left(\frac{A_2}{A_1}\right) = F_1\left(\frac{D_2}{D_1}\right)^2. Because the output piston has a larger area, the output force must be greater than the input force.

  2. Step 2

    m=F2g=1.218759.80=0.124 kgm = \frac{F_2}{g} = \frac{1.21875}{9.80} = 0.124\text{ kg}

    Correct

    m=F2g=4992 N9.80 m/s2≈509 kgm = \frac{F_2}{g} = \frac{4992\text{ N}}{9.80\text{ m/s}^2} \approx 509\text{ kg}

    You applied the gravitational equilibrium formula m=F2gm = \frac{F_2}{g} correctly, but your numerical result was affected by the incorrect value of F2F_2 from the previous step.

WHAT YOU DID WELL
Compliments from Your Teacher

You recognized that pressure is transmitted through the fluid to balance the weight of the crate.

You correctly squared the ratio of diameters to account for the circular piston areas.

You correctly used the equilibrium condition F2=mgF_2 = mg to relate the upward fluid force to the crate's mass.

THE ERROR
Where Your ACEpath Teacher Spotted the Mistake
Inverted area ratio in hydraulic lift formula

You set the ratio as (D1D2)2\left(\frac{D_1}{D_2}\right)^2 instead of (D2D1)2\left(\frac{D_2}{D_1}\right)^2 when isolating F2F_2.

WHY IT HAPPENED
ACEpath Teacher's Diagnosis

You solved F1A1=F2A2\frac{F_1}{A_1} = \frac{F_2}{A_2} by accidentally multiplying F1F_1 by A1A2\frac{A_1}{A_2} rather than multiplying both sides by A2A_2 to isolate F2F_2. A quick physical check confirms that a hydraulic lift is meant to multiply force, so the larger piston must support a larger force (F2>F1F_2 > F_1).

REASONING PATH
Your ACEpath teacher’s suggested approach
Isolate the unknown force correctly
  • Starting from F1A1=F2A2\frac{F_1}{A_1} = \frac{F_2}{A_2}, multiply both sides by A2A_2 to obtain F2=F1(A2A1)F_2 = F_1 \left(\frac{A_2}{A_1}\right).

  • Always write down the fundamental definition F1A1=F2A2\frac{F_1}{A_1} = \frac{F_2}{A_2} first, then clear the denominator directly under your target variable.

Perform a physical sanity check
  • A larger cross-sectional area under the same pressure must exert a proportionally larger total force: A2>A1  ⟹  F2>F1A_2 > A_1 \implies F_2 > F_1.

  • Check whether your calculated output force is greater than the input force when the output cylinder is wider.

CORRECTED PATH
ACEpath Teacher's Demonstration
  1. Apply Pascal's principle: F1A1=F2A2  ⟹  F2=F1(D2D1)2\frac{F_1}{A_1} = \frac{F_2}{A_2} \implies F_2 = F_1 \left(\frac{D_2}{D_1}\right)^2.

  2. Substitute the given values: F2=78.0 N×(32.0 cm4.00 cm)2=78.0 N×64=4992 NF_2 = 78.0\text{ N} \times \left(\frac{32.0\text{ cm}}{4.00\text{ cm}}\right)^2 = 78.0\text{ N} \times 64 = 4992\text{ N}.

  3. Calculate the supported mass from equilibrium: m=F2g=4992 N9.80 m/s2≈509 kgm = \frac{F_2}{g} = \frac{4992\text{ N}}{9.80\text{ m/s}^2} \approx 509\text{ kg}.

Final answer

m=509 kgm = 509\text{ kg}

NEXT STEPS
Final Takeaways from Your Teacher
  • Review algebraic isolation of variables in proportions to ensure multipliers are not inverted.

  • Practice using the physical principle that hydraulic lifts provide a mechanical advantage (F2/F1=A2/A1>1F_2 / F_1 = A_2 / A_1 > 1) to verify your answers.

Lock it in

Similar question

01

A hydraulic press has an input piston of radius r1=2.0 cmr_1 = 2.0\text{ cm} and an output piston of radius r2=10.0 cmr_2 = 10.0\text{ cm}. If an input force of F1=50 NF_1 = 50\text{ N} is applied, what is the ideal output force F2F_2?

Answer

F2=1250 NF_2 = 1250\text{ N}. Using Pascal's principle, F2F1=(r2r1)2=(10.02.0)2=25\frac{F_2}{F_1} = \left(\frac{r_2}{r_1}\right)^2 = \left(\frac{10.0}{2.0}\right)^2 = 25. Therefore, F2=50 N×25=1250 NF_2 = 50\text{ N} \times 25 = 1250\text{ N}.

02

A mechanic uses a hydraulic car lift where the output piston diameter is 30.0 cm30.0\text{ cm} and the input piston diameter is 3.00 cm3.00\text{ cm}. What minimum force F1F_1 must be exerted on the input cylinder to hold a 1500 kg1500\text{ kg} vehicle at rest? (Take g=9.80 m/s2g = 9.80\text{ m/s}^2)

Answer

F1=147 NF_1 = 147\text{ N}. The required output force is F2=mg=1500×9.80=14700 NF_2 = mg = 1500 \times 9.80 = 14700\text{ N}. The diameter ratio is D2D1=30.03.00=10\frac{D_2}{D_1} = \frac{30.0}{3.00} = 10, giving an area ratio of 102=10010^2 = 100. Thus, F1=F2100=14700 N100=147 NF_1 = \frac{F_2}{100} = \frac{14700\text{ N}}{100} = 147\text{ N}.

03

In a hydraulic brake system, a master cylinder has diameter D1=2.50 cmD_1 = 2.50\text{ cm} and applies force to four identical slave wheel cylinders, each having diameter D2=3.75 cmD_2 = 3.75\text{ cm}. If a driver exerts a force of F1=200 NF_1 = 200\text{ N} on the master cylinder, what is the normal braking force exerted by each individual wheel cylinder?

Answer

F2=450 NF_2 = 450\text{ N}. The pressure in the entire closed brake line is P=F1A1P = \frac{F_1}{A_1}. Each slave cylinder experiences this identical pressure: F2=P⋅A2=F1(D2D1)2=200 N×(3.752.50)2=200×(1.5)2=200×2.25=450 NF_2 = P \cdot A_2 = F_1 \left(\frac{D_2}{D_1}\right)^2 = 200\text{ N} \times \left(\frac{3.75}{2.50}\right)^2 = 200 \times (1.5)^2 = 200 \times 2.25 = 450\text{ N}.

Loading workspace…