Resources

A high-precision analog voltmeter with an internal resistance of R=4.50 MΩR = 4.50\,\mathrm{M}\Omega is connected across an integrated circuit trace. A microammeter records a tiny leakage current of I=320 μAI = 320\,\mu\mathrm{A} flowing through the meter's internal resistance. Calculate the potential difference VV across the meter terminals, expressing the final answer in millivolts (mV\text{mV}).

Answer and steps

Final answer

1.44×106 mV1.44 \times 10^{6}\text{ mV}

Steps

01

Convert Given Quantities to SI Base Units

Identify the known quantities and convert their metric prefixes into base SI units:

  • Resistance: R=4.50 MΩ=4.50×106 ΩR = 4.50\text{ M}\Omega = 4.50 \times 10^{6}\text{ }\Omega
  • Current: I=320 μA=320×10−6 A=3.20×10−4 AI = 320\text{ }\mu\text{A} = 320 \times 10^{-6}\text{ A} = 3.20 \times 10^{-4}\text{ A}

Helpful Tip on Metric Prefixes: Notice that the prefix mega (M=106\text{M} = 10^6) and micro (μ=10−6\mu = 10^{-6}) are reciprocal powers of ten (106⋅10−6=100=110^6 \cdot 10^{-6} = 10^0 = 1). Multiplying microamperes directly by megaohms immediately yields volts.


02

Apply Ohm's Law

According to Ohm's law, the potential difference VV across a resistor is directly proportional to the current II flowing through it: V=I⋅RV = I \cdot R

Substitute the converted values: V=(3.20×10−4 A)⋅(4.50×106 Ω)V = (3.20 \times 10^{-4}\text{ A}) \cdot (4.50 \times 10^{6}\text{ }\Omega) V=1440 V=1.44×103 VV = 1440\text{ V} = 1.44 \times 10^{3}\text{ V}


03

Convert the Potential Difference to Millivolts (mV\text{mV})

The question requires the final answer in millivolts. Since 1 V=103 mV1\text{ V} = 10^{3}\text{ mV}: V=1440 V⋅103 mV1 V=1.44×106 mVV = 1440\text{ V} \cdot \frac{10^{3}\text{ mV}}{1\text{ V}} = 1.44 \times 10^{6}\text{ mV}


Common Pitfall to Avoid

Do not confuse the prefix milli (m=10−3\text{m} = 10^{-3}) with mega (M=106\text{M} = 10^{6}). Converting from volts to millivolts means multiplying by 10310^{3}, not dividing.

Typical errors

OverviewACEpath Teacher's Diagnosis

01 The student inverts the metric prefix conversion when converting volts to millivolts, dividing by 1000 instead of multiplying by 1000.

Sample Student Work

Reviewed by ACEpath Teacher
Step-by-Step Review
Walk Through It with Your Teacher
Incorrect
  1. Step 1

    V=I⋅R  ⟹  I=320×10−6 A,  R=4.50×106  Ω  ⟹  V=(320×10−6 A)(4.50×106  Ω)=1440 VV = I \cdot R \implies I = 320 \times 10^{-6}\text{ A},\; R = 4.50 \times 10^6\;\Omega \implies V = (320 \times 10^{-6}\text{ A})(4.50 \times 10^6\;\Omega) = 1440\text{ V}

  2. Step 2

    V=14401000=1.44 mVV = \frac{1440}{1000} = 1.44\text{ mV}

    Correct

    V=1440 V×103 mV1 V=1.44×106 mVV = 1440\text{ V} \times \frac{10^3\text{ mV}}{1\text{ V}} = 1.44 \times 10^6\text{ mV}

    You divided by 10001000 instead of multiplying by 10001000. Because 1 V=1000 mV1\text{ V} = 1000\text{ mV}, converting from a larger unit (volts) to a smaller unit (millivolts) requires multiplying by 10310^3.

WHAT YOU DID WELL
Compliments from Your Teacher

You correctly recalled and applied Ohm's law, V=I⋅RV = I \cdot R.

You correctly expressed microamperes (μA\mu\text{A}) and megaohms (MΩ\text{M}\Omega) in base SI units.

You performed the multiplication accurately to obtain 1440 V1440\text{ V}.

THE ERROR
Where Your ACEpath Teacher Spotted the Mistake
Inverted metric unit conversion

You divided by 10001000 to convert from volts to millivolts instead of multiplying.

WHY IT HAPPENED
ACEpath Teacher's Diagnosis

Confusing the direction of metric unit conversions: converting from a base unit to a milli-prefix unit requires multiplying by 10310^3 because there are 10001000 millivolts in every volt.

REASONING PATH
Your ACEpath teacher’s suggested approach
Unit Size Check
  • When going from a larger unit to a smaller unit, the numerical value must increase.

  • Always write out dimensional cancellation explicitly: value in V×1000 mV1 V\text{value in V} \times \frac{1000\text{ mV}}{1\text{ V}}.

CORRECTED PATH
ACEpath Teacher's Demonstration
  1. Apply the conversion factor between volts and millivolts: 1 V=103 mV1\text{ V} = 10^3\text{ mV}.

  2. Multiply the voltage in volts by 103 mV/V10^3\text{ mV/V}: V=1440 V×1000 mV/V=1.44×106 mVV = 1440\text{ V} \times 1000\text{ mV/V} = 1.44 \times 10^6\text{ mV}.

Final answer

1.44×106 mV1.44 \times 10^6\text{ mV}

NEXT STEPS
Final Takeaways from Your Teacher
  • Practice using dimensional analysis cancellation brackets for all unit conversions.

  • Double-check that converting to a smaller unit (like millivolts) makes the number larger, not smaller.

OverviewACEpath Teacher's Diagnosis

02 The student misinterprets the megaohm prefix as 10³ instead of 10⁶, confusing mega with kilo.

Sample Student Work

Reviewed by ACEpath Teacher
Step-by-Step Review
Walk Through It with Your Teacher
Incorrect
  1. Step 1

    V=I⋅R  ⟹  I=320×10−6 A  ⟹  R=4.50×103 ΩV = I \cdot R \implies I = 320 \times 10^{-6}\text{ A} \implies R = 4.50 \times 10^{3}\ \Omega

    Correct

    V=I⋅R  ⟹  I=320×10−6 A  ⟹  R=4.50×106 ΩV = I \cdot R \implies I = 320 \times 10^{-6}\text{ A} \implies R = 4.50 \times 10^{6}\ \Omega

    You stated Ohm's law and converted microamperes to amperes correctly (320 \muA=320×10−6 A320\text{ \mu A} = 320 \times 10^{-6}\text{ A}). However, you interpreted megaohms (MΩ\text{M}\Omega) as 103 Ω10^{3}\ \Omega instead of 106 Ω10^{6}\ \Omega, mistaking mega for kilo.

  2. Step 2

    V=(320×10−6 A)(4.50×103 Ω)  ⟹  V=1.44 VV = (320 \times 10^{-6}\text{ A})(4.50 \times 10^{3}\ \Omega) \implies V = 1.44\text{ V}

    Correct

    V=(320×10−6 A)(4.50×106 Ω)  ⟹  V=1440 VV = (320 \times 10^{-6}\text{ A})(4.50 \times 10^{6}\ \Omega) \implies V = 1440\text{ V}

    Your arithmetic evaluation was correct for the numbers you substituted, but the resulting voltage was affected by the resistance prefix error in Step 1.

  3. Step 3

    V=1.44×1000=1440 mVV = 1.44 \times 1000 = 1440\text{ mV}

    Correct

    V=1440×1000=1.44×106 mVV = 1440 \times 1000 = 1.44 \times 10^{6}\text{ mV}

    You correctly multiplied by 10001000 to convert from volts to millivolts, but because the input voltage was 1.44 V1.44\text{ V} instead of 1440 V1440\text{ V}, the final answer is 1440 mV1440\text{ mV} instead of 1.44×106 mV1.44 \times 10^{6}\text{ mV}.

WHAT YOU DID WELL
Compliments from Your Teacher

You correctly identified and applied Ohm's law, V=I⋅RV = I \cdot R.

You accurately converted microamperes to base amperes using 10−610^{-6}.

You correctly recognized that converting volts to millivolts requires multiplying by 10310^{3}.

THE ERROR
Where Your ACEpath Teacher Spotted the Mistake
Metric prefix confusion (Mega vs Kilo)

You substituted 10310^{3} instead of 10610^{6} for the prefix mega (M\text{M}).

WHY IT HAPPENED
ACEpath Teacher's Diagnosis

Confusing the metric prefix mega (M=106\text{M} = 10^{6}) with kilo (k=103\text{k} = 10^{3}). Remembering that capital M\text{M} indicates one million will prevent underestimating high resistances by three orders of magnitude.

REASONING PATH
Your ACEpath teacher’s suggested approach
Metric Prefix Verification
  • M=106\text{M} = 10^{6} (Mega), while k=103\text{k} = 10^{3} (Kilo) and m=10−3\text{m} = 10^{-3} (milli).

  • Before performing circuit calculations, write out each metric prefix as its explicit power of ten: replace MΩ\text{M}\Omega directly with ×106 Ω\times 10^{6}\ \Omega.

CORRECTED PATH
ACEpath Teacher's Demonstration
  1. Convert resistance to SI base units using the correct mega prefix: R=4.50 MΩ=4.50×106 ΩR = 4.50\text{ M}\Omega = 4.50 \times 10^{6}\ \Omega.

  2. Multiply current by resistance using Ohm's law: V=(320×10−6 A)(4.50×106 Ω)=1440 VV = (320 \times 10^{-6}\text{ A})(4.50 \times 10^{6}\ \Omega) = 1440\text{ V}.

  3. Convert the potential difference to millivolts: V=1440 V×103 mV/V=1.44×106 mVV = 1440\text{ V} \times 10^{3}\text{ mV/V} = 1.44 \times 10^{6}\text{ mV}.

Final answer

1.44×106 mV1.44 \times 10^{6}\text{ mV}

NEXT STEPS
Final Takeaways from Your Teacher
  • Review the metric prefix table, focusing on the differences between mega (M=106\text{M} = 10^{6}), kilo (k=103\text{k} = 10^{3}), and milli (m=10−3\text{m} = 10^{-3}).

  • Practice using the shortcut (μA)×(MΩ)=V(\mu\text{A}) \times (\text{M}\Omega) = \text{V}, since 10−6×106=100=110^{-6} \times 10^{6} = 10^{0} = 1.

OverviewACEpath Teacher's Diagnosis

03 The student uses Ohm's law in the inverted form V = I / R instead of V = I · R.

Sample Student Work

Reviewed by ACEpath Teacher
Step-by-Step Review
Walk Through It with Your Teacher
Incorrect
  1. Step 1

    I=3.20×10−4 A  ⟹  R=4.50×106 ΩI = 3.20 \times 10^{-4}\text{ A} \implies R = 4.50 \times 10^{6}\text{ }\Omega

  2. Step 2

    V=IR  ⟹  V=3.20×10−4 A4.50×106 Ω=7.11×10−11 VV = \frac{I}{R} \implies V = \frac{3.20 \times 10^{-4}\text{ A}}{4.50 \times 10^{6}\text{ }\Omega} = 7.11 \times 10^{-11}\text{ V}

    Correct

    V=I⋅R=(3.20×10−4 A)⋅(4.50×106 Ω)=1440 V=1.44×103 VV = I \cdot R = (3.20 \times 10^{-4}\text{ A}) \cdot (4.50 \times 10^{6}\text{ }\Omega) = 1440\text{ V} = 1.44 \times 10^{3}\text{ V}

    Ohm's law states that potential difference is the product of current and resistance (V=I⋅RV = I \cdot R). You divided the current by the resistance (V=IRV = \frac{I}{R}) instead of multiplying them.

  3. Step 3

    V=7.11×10−11×1000=7.11×10−8 mVV = 7.11 \times 10^{-11} \times 1000 = 7.11 \times 10^{-8}\text{ mV}

    Correct

    V=1440 V⋅103 mV/V=1.44×106 mVV = 1440\text{ V} \cdot 10^{3}\text{ mV/V} = 1.44 \times 10^{6}\text{ mV}

    Your unit conversion method from volts to millivolts was mathematically sound, but the numerical result is incorrect due to the inverted formula in the previous step.

WHAT YOU DID WELL
Compliments from Your Teacher

You correctly converted 320 μA320\text{ }\mu\text{A} to 3.20×10−4 A3.20 \times 10^{-4}\text{ A} and 4.50 MΩ4.50\text{ M}\Omega to 4.50×106 Ω4.50 \times 10^{6}\text{ }\Omega.

You correctly recognized that converting from volts to millivolts requires multiplying by 10310^{3}.

THE ERROR
Where Your ACEpath Teacher Spotted the Mistake
Ohm's Law Inversion

You wrote V=IRV = \frac{I}{R} instead of V=I⋅RV = I \cdot R.

WHY IT HAPPENED
ACEpath Teacher's Diagnosis

You confused the formula for current (I=VRI = \frac{V}{R}) with the formula for potential difference (V=I⋅RV = I \cdot R). Remember that potential difference drives current through resistance, so higher resistance requires a larger voltage for the same current.

REASONING PATH
Your ACEpath teacher’s suggested approach
Ohm's Law Triangle
  • V=I⋅RV = I \cdot R, while I=VRI = \frac{V}{R} and R=VIR = \frac{V}{I}.

  • Before calculating, verify your formula by checking units: Volts=Amperes×Ohms\text{Volts} = \text{Amperes} \times \text{Ohms}, whereas AmperesOhms\frac{\text{Amperes}}{\text{Ohms}} does not equal volts.

CORRECTED PATH
ACEpath Teacher's Demonstration
  1. V=I⋅R=(3.20×10−4 A)⋅(4.50×106 Ω)=1440 VV = I \cdot R = (3.20 \times 10^{-4}\text{ A}) \cdot (4.50 \times 10^{6}\text{ }\Omega) = 1440\text{ V}

  2. V=1440 V×103 mV/V=1.44×106 mVV = 1440\text{ V} \times 10^{3}\text{ mV/V} = 1.44 \times 10^{6}\text{ mV}

Final answer

1.44×106 mV1.44 \times 10^{6}\text{ mV}

NEXT STEPS
Final Takeaways from Your Teacher
  • Review the Ohm's law triangle to ensure you rearrange V=I⋅RV = I \cdot R correctly for any unknown variable.

  • Perform dimensional analysis on your formulas to catch algebraic inversions before substituting numbers.

Lock it in

Similar question

01

A resistor of resistance R=2.50 kΩR = 2.50\text{ k}\Omega carries a current of I=15.0 mAI = 15.0\text{ mA}. Calculate the potential difference across the resistor in millivolts (mV\text{mV}).

Answer

3.75×104 mV3.75 \times 10^4\text{ mV}. First, convert to base units: R=2500  ΩR = 2500\;\Omega and I=0.0150 AI = 0.0150\text{ A}. Then apply Ohm's law: V=I⋅R=(0.0150 A)(2500  Ω)=37.5 VV = I \cdot R = (0.0150\text{ A})(2500\;\Omega) = 37.5\text{ V}. Finally, convert to millivolts: 37.5 V×1000 mV/V=37 500 mV=3.75×104 mV37.5\text{ V} \times 1000\text{ mV/V} = 37\,500\text{ mV} = 3.75 \times 10^4\text{ mV}.

02

A current of I=80.0 μAI = 80.0\text{ }\mu\text{A} passes through an internal meter resistance of R=12.0 MΩR = 12.0\text{ M}\Omega. Find the terminal voltage VV in millivolts (mV\text{mV}), expressing your answer in scientific notation.

Answer

9.60×105 mV9.60 \times 10^5\text{ mV}. Calculate the voltage in volts: V=(80.0×10−6 A)(12.0×106  Ω)=960 VV = (80.0 \times 10^{-6}\text{ A})(12.0 \times 10^6\;\Omega) = 960\text{ V}. Convert to millivolts: 960 V×103 mV/V=9.60×105 mV960\text{ V} \times 10^3\text{ mV/V} = 9.60 \times 10^5\text{ mV}.

03

An operational amplifier circuit maintains a potential difference of V=72.0 mVV = 72.0\text{ mV} across an input resistor R=1.80 MΩR = 1.80\text{ M}\Omega. Calculate the current II flowing through the resistor, expressing the final answer in nanoamperes (nA\text{nA}).

Answer

40.0 nA40.0\text{ nA}. Convert given values to base SI units: V=72.0 mV=72.0×10−3 V=0.0720 VV = 72.0\text{ mV} = 72.0 \times 10^{-3}\text{ V} = 0.0720\text{ V}, and R=1.80×106  ΩR = 1.80 \times 10^6\;\Omega. By Ohm's law, I=VR=72.0×10−3 V1.80×106  Ω=4.00×10−8 AI = \frac{V}{R} = \frac{72.0 \times 10^{-3}\text{ V}}{1.80 \times 10^6\;\Omega} = 4.00 \times 10^{-8}\text{ A}. Convert to nanoamperes: 4.00×10−8 A×109 nA/A=40.0 nA4.00 \times 10^{-8}\text{ A} \times 10^9\text{ nA/A} = 40.0\text{ nA}.

Loading workspace…