Resources

A civil engineer designs an unbanked circular exit ramp with a radius of curvature of r=85.0 mr = 85.0\text{ m}. Highway safety regulations dictate that passenger vehicles traveling at a posted speed limit of v=22.0 m/sv = 22.0\text{ m/s} must not skid under dry road conditions. Assuming g=9.80 m/s2g = 9.80\text{ m/s}^2, determine the minimum static coefficient of friction μs\mu_s between the tires and the road necessary to provide the required centripetal acceleration.

Answer and steps

Final answer

μs,min⁡=0.581\mu_{s,\min} = 0.581

Steps

01

Identify the Forces Acting on the Vehicle

On an unbanked (flat) horizontal curve, the car moves along a circular path of radius rr at a constant speed vv. A net force directed toward the center of the curve is required to provide this centripetal acceleration.

Consider the forces acting on the car of mass mm:

  • Vertical direction: The upward normal force FNF_N balances the downward gravitational force Fg=mgF_g = mg: FN=mgF_N = mg
  • Horizontal direction: Since the road is completely flat, the normal force has no horizontal component. The only horizontal force acting toward the center of curvature is the static friction force fsf_s between the car's tires and the road: Fnet, radial=fsF_{\text{net, radial}} = f_s

Common Pitfall: Even though the car is moving forward, the contact patch of a rolling tire does not slide relative to the road surface. Therefore, the force preventing the car from sliding outward is static friction, not kinetic friction.


02

Relate Friction to Centripetal Acceleration

According to Newton's second law for uniform circular motion: Fc=mv2rF_c = \frac{m v^2}{r}

To keep the car on the circular path without slipping outward, static friction must supply this entire centripetal force: fs=mv2rf_s = \frac{m v^2}{r}

The available static friction cannot exceed its maximum threshold: fs≤fs,max⁡=μsFN=μsmgf_s \le f_{s,\max} = \mu_s F_N = \mu_s mg

Combining these inequalities gives: mv2r≤μsmg\frac{m v^2}{r} \le \mu_s mg


03

Solve for the Minimum Coefficient of Static Friction

Notice that the mass mm cancels out from both sides, showing that the required friction is independent of vehicle mass: μs≥v2rg\mu_s \ge \frac{v^2}{r g}

The minimum coefficient of static friction μs,min⁡\mu_{s,\min} corresponds to the limit where the required centripetal force equals the maximum static friction: μs,min⁡=v2rg\mu_{s,\min} = \frac{v^2}{r g}


04

Substitute the Given Values

Substitute v=22.0 m/sv = 22.0\text{ m/s}, r=85.0 mr = 85.0\text{ m}, and g=9.80 m/s2g = 9.80\text{ m/s}^2: μs,min⁡=(22.0)285.0⋅9.80=484833≈0.581\mu_{s,\min} = \frac{(22.0)^2}{85.0 \cdot 9.80} = \frac{484}{833} \approx 0.581

Thus, the minimum coefficient of static friction required to prevent skidding is 0.5810.581.

Typical errors

OverviewACEpath Teacher's Diagnosis

01 The student forgets to square the velocity when expressing the centripetal acceleration formula, resulting in μ_s = v / (r * g).

Sample Student Work

Reviewed by ACEpath Teacher
Step-by-Step Review
Walk Through It with Your Teacher
Incorrect
  1. Step 1

    Fc=fsF_c = f_s

  2. Step 2

    m⋅vr=μs⋅m⋅g\frac{m \cdot v}{r} = \mu_s \cdot m \cdot g

    Correct

    mv2r=μsmg\frac{m v^2}{r} = \mu_s m g

    Centripetal acceleration is ac=v2ra_c = \frac{v^2}{r}, so the centripetal force is Fc=mv2rF_c = \frac{m v^2}{r}. You wrote mvr\frac{m v}{r}, omitting the square on speed vv.

  3. Step 3

    μs=vr⋅g\mu_s = \frac{v}{r \cdot g}

    Correct

    μs=v2rg\mu_s = \frac{v^2}{r g}

    You solved for μs\mu_s correctly based on your equation from Step 2, but the expression inherits the missing exponent.

  4. Step 4

    μs=22.085.0⋅9.80  ⟹  μs=22.0833≈0.0264\mu_s = \frac{22.0}{85.0 \cdot 9.80} \implies \mu_s = \frac{22.0}{833} \approx 0.0264

    Correct

    μs,min⁡=(22.0)285.0⋅9.80=484833≈0.581\mu_{s,\min} = \frac{(22.0)^2}{85.0 \cdot 9.80} = \frac{484}{833} \approx 0.581

    Your numerical calculation is internally consistent with your formula, but the resulting value is incorrect due to the missing square.

WHAT YOU DID WELL
Compliments from Your Teacher

You recognized that horizontal static friction is the sole force providing centripetal acceleration on a flat road.

You correctly expressed maximum static friction as fs,max⁡=μsmgf_{s,\max} = \mu_s m g.

You accurately carried out the algebra and division according to your setup.

THE ERROR
Where Your ACEpath Teacher Spotted the Mistake
Formula recall error

no

WHY IT HAPPENED
ACEpath Teacher's Diagnosis

You recalled centripetal acceleration with linear velocity vv instead of quadratic velocity v2v^2, which also violates dimensional consistency since vr\frac{v}{r} has units of s−1\text{s}^{-1} rather than m/s2\text{m/s}^2.

REASONING PATH
Your ACEpath teacher’s suggested approach
Centripetal Acceleration Formula
  • Centripetal acceleration for speed vv along radius rr is ac=v2ra_c = \frac{v^2}{r}, giving Fc=mv2rF_c = \frac{m v^2}{r}.

  • Always verify that your acceleration expression has units of m/s2\text{m/s}^2: (m/s)2m=m2/s2m=m/s2\frac{(\text{m/s})^2}{\text{m}} = \frac{\text{m}^2/\text{s}^2}{\text{m}} = \text{m/s}^2.

CORRECTED PATH
ACEpath Teacher's Demonstration
  1. Set the centripetal force equal to maximum static friction: mv2r=μsmg\frac{m v^2}{r} = \mu_s m g.

  2. Cancel mass mm and solve for μs\mu_s: μs=v2rg\mu_s = \frac{v^2}{r g}.

  3. Substitute the given numbers: μs=(22.0)2(85.0)(9.80)=484833≈0.581\mu_s = \frac{(22.0)^2}{(85.0)(9.80)} = \frac{484}{833} \approx 0.581.

Final answer

μs,min⁡≈0.581\mu_{s,\min} \approx 0.581

NEXT STEPS
Final Takeaways from Your Teacher
  • Double-check dimensional units whenever you write down kinematics and force formulas.

  • Practice recalculating maximum safe speeds and required friction coefficients for unbanked turns using v2=μsgrv^2 = \mu_s g r.

OverviewACEpath Teacher's Diagnosis

02 The student multiplies by acceleration due to gravity instead of dividing when rearranging the equilibrium equation, leading to μ_s = v² * g / r.

Sample Student Work

Reviewed by ACEpath Teacher
Step-by-Step Review
Walk Through It with Your Teacher
Incorrect
  1. Step 1

    μs∗m∗g=m∗v2r\mu_s * m * g = m * \frac{v^2}{r}

  2. Step 2

    μs=v2∗gr\mu_s = \frac{v^2 * g}{r}

    Correct

    μs=v2rg\mu_s = \frac{v^2}{r g}

    To isolate μs\mu_s, both sides must be divided by mgm g. Dividing by gg places it in the denominator, giving μs=v2rg\mu_s = \frac{v^2}{r g} rather than multiplying by gg in the numerator.

  3. Step 3

    μs=(22.0)2∗9.8085.0  ⟹  μs=484∗9.8085.0  ⟹  μs≈55.8\mu_s = \frac{(22.0)^2 * 9.80}{85.0} \implies \mu_s = \frac{484 * 9.80}{85.0} \implies \mu_s \approx 55.8

    Correct

    μs=(22.0)2(85.0)(9.80)=484833≈0.581\mu_s = \frac{(22.0)^2}{(85.0)(9.80)} = \frac{484}{833} \approx 0.581

    Your numerical calculations followed your rearranged formula correctly, but the result was incorrect due to the inverted placement of gg in the previous step.

WHAT YOU DID WELL
Compliments from Your Teacher

You recognized that static friction provides the necessary centripetal force for an unbanked curve.

You correctly substituted the given values into your derived expression.

You performed the arithmetic accurately based on your algebraic formula.

THE ERROR
Where Your ACEpath Teacher Spotted the Mistake
Algebraic Rearrangement Error

You multiplied by the acceleration due to gravity gg instead of dividing both sides by gg when isolating μs\mu_s.

WHY IT HAPPENED
ACEpath Teacher's Diagnosis

Inverting division when rearranging a linear factor across an equality sign, combined with overlooking a dimensional/magnitude sanity check (coefficients of friction are dimensionless and typically less than or close to 11, whereas 55.855.8 has units of m2/s4\text{m}^2/\text{s}^4).

REASONING PATH
Your ACEpath teacher’s suggested approach
Isolating Factors via Inverse Operations
  • If A⋅B=CA \cdot B = C, then isolating AA requires dividing both sides by BB: A=CBA = \frac{C}{B}.

  • Divide both sides of μsmg=mv2r\mu_s m g = \frac{m v^2}{r} by mgm g so that gg ends up in the denominator alongside rr.

Dimensional and Magnitude Sanity Check
  • The coefficient of static friction μs\mu_s is a dimensionless ratio, and for standard car tires on dry asphalt, it typically falls between 0.50.5 and 1.01.0.

  • Always verify that your formula yields a dimensionless quantity: v2rg=(m/s)2m⋅(m/s2)=1\frac{v^2}{rg} = \frac{(\text{m/s})^2}{\text{m} \cdot (\text{m/s}^2)} = 1.

CORRECTED PATH
ACEpath Teacher's Demonstration
  1. Divide both sides by mm: μsg=v2r\mu_s g = \frac{v^2}{r}

  2. Divide both sides by gg: μs=v2rg\mu_s = \frac{v^2}{r g}

  3. Substitute the given numbers: μs=(22.0)285.0×9.80=484833≈0.581\mu_s = \frac{(22.0)^2}{85.0 \times 9.80} = \frac{484}{833} \approx 0.581

Final answer

μs,min⁡=0.581\mu_{s,\min} = 0.581

NEXT STEPS
Final Takeaways from Your Teacher
  • Practice isolating variables with two or more factors in the denominator.

  • Perform dimensional analysis on derived physics expressions before substituting numbers.

  • Check that coefficients of friction give realistic physical values (typically between 00 and 11).

OverviewACEpath Teacher's Diagnosis

03 The student inverts the radius and speed term in the centripetal acceleration expression, using r / v² instead of v² / r.

Sample Student Work

Reviewed by ACEpath Teacher
Step-by-Step Review
Walk Through It with Your Teacher
Incorrect
  1. Step 1

    fs=m⋅acf_s = m \cdot a_c

  2. Step 2

    μs⋅m⋅g=m⋅rv2  ⟹  μs=rg⋅v2\mu_s \cdot m \cdot g = \frac{m \cdot r}{v^2} \implies \mu_s = \frac{r}{g \cdot v^2}

    Correct

    μsmg=mv2r  ⟹  μs=v2rg\mu_s m g = \frac{m v^2}{r} \implies \mu_s = \frac{v^2}{r g}

    Centripetal acceleration is ac=v2ra_c = \frac{v^2}{r}, not rv2\frac{r}{v^2}. Inverting the ratio gave an expression with the wrong physical dimensions.

  3. Step 3

    μs=85.09.80⋅22.02  ⟹  μs=85.04743.2≈0.0179\mu_s = \frac{85.0}{9.80 \cdot 22.0^2} \implies \mu_s = \frac{85.0}{4743.2} \approx 0.0179

    Correct

    μs=22.0285.0⋅9.80=484833≈0.581\mu_s = \frac{22.0^2}{85.0 \cdot 9.80} = \frac{484}{833} \approx 0.581

    Your arithmetic followed directly from your inverted formula, which carried the earlier error into the final number.

WHAT YOU DID WELL
Compliments from Your Teacher

You correctly identified static friction as the radial force providing circular motion.

You accurately substituted FN=mgF_N = mg to express the maximum available static friction as μsmg\mu_s m g.

You correctly eliminated the vehicle mass mm algebraically from both sides of the force balance.

THE ERROR
Where Your ACEpath Teacher Spotted the Mistake
Formula Inversion Error

You wrote ac=rv2a_c = \frac{r}{v^2} instead of ac=v2ra_c = \frac{v^2}{r}.

WHY IT HAPPENED
ACEpath Teacher's Diagnosis

Confusing the numerator and denominator in the kinematic expression for centripetal acceleration, which can be caught immediately by checking units (m/s²).

REASONING PATH
Your ACEpath teacher’s suggested approach
Centripetal Acceleration Definition
  • Centripetal acceleration for circular motion of radius rr at speed vv is ac=v2ra_c = \frac{v^2}{r}.

  • Always verify that aca_c has units of acceleration: (m/s)2m=m2/s2m=m/s2\frac{(\text{m/s})^2}{\text{m}} = \frac{\text{m}^2/\text{s}^2}{\text{m}} = \text{m/s}^2.

Dimensionless Coefficient Check
  • The friction coefficient μs\mu_s must be dimensionless.

  • In μs=v2rg\mu_s = \frac{v^2}{rg}, the units m2/s2m⋅(m/s2)=1\frac{\text{m}^2/\text{s}^2}{\text{m} \cdot (\text{m/s}^2)} = 1 cancel out. In your inverted formula rgv2\frac{r}{gv^2}, the units are s4/m2\text{s}^4/\text{m}^2, which signals an algebraic inversion.

CORRECTED PATH
ACEpath Teacher's Demonstration
  1. Substitute ac=v2ra_c = \frac{v^2}{r} into the radial equation: μsmg=mv2r\mu_s m g = \frac{m v^2}{r}.

  2. Divide both sides by mgm g: μs=v2rg\mu_s = \frac{v^2}{r g}.

  3. Substitute the given numbers: μs=(22.0)285.0×9.80=484833\mu_s = \frac{(22.0)^2}{85.0 \times 9.80} = \frac{484}{833}.

  4. Evaluate the final quotient: μs≈0.581\mu_s \approx 0.581.

Final answer

μs,min⁡≈0.581\mu_{s,\min} \approx 0.581

NEXT STEPS
Final Takeaways from Your Teacher
  • Double-check that ac=v2ra_c = \frac{v^2}{r} before substituting numerical quantities into force equations.

  • Perform a quick dimensional check whenever you derive a formula for a dimensionless constant like μs\mu_s.

Lock it in

Similar question

01

A car travels around a flat circular track of radius r=50.0 mr = 50.0\text{ m} at a constant speed of v=14.0 m/sv = 14.0\text{ m/s}. Taking g=9.80 m/s2g = 9.80\text{ m/s}^2, calculate the minimum coefficient of static friction μs\mu_s required to prevent sliding.

Answer

μs,min⁡=0.400\mu_{s,\min} = 0.400. From μs=v2rg\mu_s = \frac{v^2}{r g}, substitute values: μs=14.0250.0×9.80=196490=0.400\mu_s = \frac{14.0^2}{50.0 \times 9.80} = \frac{196}{490} = 0.400.

02

A flat highway curve has a radius of curvature of r=120 mr = 120\text{ m}. If the coefficient of static friction between the road and tires on a wet day is μs=0.350\mu_s = 0.350, what is the maximum speed vmax⁡v_{\max} (in m/s\text{m/s}) at which a car can take the curve without skidding? (Use g=9.80 m/s2g = 9.80\text{ m/s}^2.)

Answer

vmax⁡≈20.3 m/sv_{\max} \approx 20.3\text{ m/s}. From vmax⁡=μsrgv_{\max} = \sqrt{\mu_s r g}, substitute values: v=0.350×120×9.80=411.6≈20.3 m/sv = \sqrt{0.350 \times 120 \times 9.80} = \sqrt{411.6} \approx 20.3\text{ m/s}.

03

Two cars of masses mA=1000 kgm_A = 1000\text{ kg} and mB=2000 kgm_B = 2000\text{ kg} negotiate the same unbanked turn of radius rr at the same speed vv. Determine the ratio of the minimum static friction coefficients required for each car, μs,Aμs,B\frac{\mu_{s,A}}{\mu_{s,B}}, and explain why mass does or does not affect this ratio.

Answer

The ratio is 1:11:1 (or 11). From μs,min⁡=v2rg\mu_{s,\min} = \frac{v^2}{r g}, the required coefficient of static friction is entirely independent of vehicle mass because both the required centripetal force (mv2/rm v^2 / r) and maximum static friction force (μsmg\mu_s m g) scale linearly with mass.

Loading workspace…