Resources

A series RCRC circuit consists of a DC voltage source E=24.0 V\mathcal{E} = 24.0\text{ V}, a resistor R=82.0 kΩR = 82.0\text{ }\text{k}\Omega, and an uncharged capacitor C=15.0 μFC = 15.0\text{ }\mu\text{F}. The circuit is closed at t=0 st = 0\text{ s}. Determine the exact elapsed time tt required for the potential difference across the resistor vR(t)v_R(t) to decrease to exactly 35.0%35.0\% of the potential difference across the capacitor vC(t)v_C(t).

Answer and steps

Final answer

t=1.66 st = 1.66\text{ s}

Steps

01

Identify the Circuit Parameters and Time Constant

In a series RCRC circuit connected to a DC source E\mathcal{E} with an initially uncharged capacitor, the circuit's response depends on the capacitive time constant τ\tau:

τ=RC\tau = RC

Substitute the given numerical values:

  • R=82.0 kΩ=8.20×104 ΩR = 82.0\text{ k}\Omega = 8.20 \times 10^4\text{ }\Omega
  • C=15.0 μF=1.50×10−5 FC = 15.0\text{ }\mu\text{F} = 1.50 \times 10^{-5}\text{ F}

τ=(8.20×104 Ω)(1.50×10−5 F)=1.23 s\tau = (8.20 \times 10^4\text{ }\Omega)(1.50 \times 10^{-5}\text{ F}) = 1.23\text{ s}


02

Set Up the Voltage Equations

At any time t≥0t \ge 0 during charging:

  • The voltage across the resistor decays exponentially from the source voltage: vR(t)=Ee−t/τv_R(t) = \mathcal{E} e^{-t/\tau}
  • The voltage across the capacitor rises toward the source voltage according to Kirchhoff's Voltage Law (vC(t)=E−vR(t)v_C(t) = \mathcal{E} - v_R(t)): vC(t)=E(1−e−t/τ)v_C(t) = \mathcal{E}(1 - e^{-t/\tau})

03

Apply the Given Condition

We are given that the resistor voltage is 35.0%35.0\% of the capacitor voltage:

vR(t)=0.350 vC(t)v_R(t) = 0.350 \, v_C(t)

Substitute the expressions for vR(t)v_R(t) and vC(t)v_C(t):

Ee−t/τ=0.350[E(1−e−t/τ)]\mathcal{E} e^{-t/\tau} = 0.350 \left[\mathcal{E} (1 - e^{-t/\tau})\right]

Divide both sides by E\mathcal{E} (which shows that the required time is independent of the source voltage):

e−t/τ=0.350(1−e−t/τ)e^{-t/\tau} = 0.350(1 - e^{-t/\tau})

Expand and gather terms involving e−t/τe^{-t/\tau}:

e−t/τ+0.350e−t/τ=0.350e^{-t/\tau} + 0.350 e^{-t/\tau} = 0.350

1.350e−t/τ=0.3501.350 e^{-t/\tau} = 0.350

e−t/τ=0.3501.350=727e^{-t/\tau} = \frac{0.350}{1.350} = \frac{7}{27}

Common Pitfall: A frequent mistake is equating vR(t)v_R(t) to 0.350E0.350 \mathcal{E} instead of 0.350vC(t)0.350 v_C(t). Notice that vC(t)v_C(t) is simultaneously changing over time, so both time-dependent functions must be included.


04

Solve for Elapsed Time tt

Take the natural logarithm of both sides:

−tτ=ln⁡(727)  ⟹  tτ=ln⁡(277)-\frac{t}{\tau} = \ln\left(\frac{7}{27}\right) \implies \frac{t}{\tau} = \ln\left(\frac{27}{7}\right)

t=τln⁡(277)t = \tau \ln\left(\frac{27}{7}\right)

Substitute τ=1.23 s\tau = 1.23\text{ s}:

t=(1.23 s)⋅ln⁡(3.85714… )≈(1.23 s)(1.3499)≈1.66 st = (1.23\text{ s}) \cdot \ln(3.85714\dots) \approx (1.23\text{ s})(1.3499) \approx 1.66\text{ s}

Typical errors

OverviewACEpath Teacher's Diagnosis

01 The student confuses the condition v_R(t) = 0.350 · v_C(t) with v_R(t) decreasing to 35.0% of its own initial maximum voltage E.

Sample Student Work

Reviewed by ACEpath Teacher
Step-by-Step Review
Walk Through It with Your Teacher
Incorrect
  1. Step 1

    τ=RC=(82.0×103)(15.0×10−6)=1.23 s\tau = RC = (82.0 \times 10^3)(15.0 \times 10^{-6}) = 1.23\text{ s}

  2. Step 2

    vR(t)=E⋅e−t/τv_R(t) = E \cdot e^{-t/\tau}

  3. Step 3

    vR(t)=0.350⋅Ev_R(t) = 0.350 \cdot E

    Correct

    vR(t)=0.350 vC(t)  ⟹  Ee−t/τ=0.350[E(1−e−t/τ)]v_R(t) = 0.350 \, v_C(t) \implies \mathcal{E} e^{-t/\tau} = 0.350 \left[\mathcal{E}(1 - e^{-t/\tau})\right]

    You equated vR(t)v_R(t) to 35.0%35.0\% of the source voltage E\mathcal{E}, but the problem asks for the instant when vR(t)v_R(t) is 35.0%35.0\% of the capacitor voltage vC(t)v_C(t), where vC(t)=E(1−e−t/τ)v_C(t) = \mathcal{E}(1 - e^{-t/\tau}).

  4. Step 4

    e−t/τ=0.350  ⟹  −t1.23=ln⁡(0.350)=−1.0498  ⟹  t=1.23⋅1.0498≈1.29 se^{-t/\tau} = 0.350 \implies \frac{-t}{1.23} = \ln(0.350) = -1.0498 \implies t = 1.23 \cdot 1.0498 \approx 1.29\text{ s}

    Correct

    e−t/τ=0.350(1−e−t/τ)  ⟹  1.350e−t/τ=0.350  ⟹  t=1.23ln⁡(1.3500.350)≈1.66 se^{-t/\tau} = 0.350(1 - e^{-t/\tau}) \implies 1.350 e^{-t/\tau} = 0.350 \implies t = 1.23 \ln\left(\frac{1.350}{0.350}\right) \approx 1.66\text{ s}

    Your algebraic solving and logarithmic evaluation were mathematically correct, but they propagated the misidentified condition from Step 3.

WHAT YOU DID WELL
Compliments from Your Teacher

You accurately determined the time constant of the RCRC circuit.

You used the correct time-dependent formula for the resistor's potential difference.

You solved the exponential equation using natural logarithms with sound algebraic technique.

THE ERROR
Where Your ACEpath Teacher Spotted the Mistake
Relative vs. Source Reference Error

You treated the benchmark voltage as the fixed source voltage E\mathcal{E} rather than the dynamic capacitor voltage vC(t)v_C(t).

WHY IT HAPPENED
ACEpath Teacher's Diagnosis

In charging RCRC circuits, both vR(t)v_R(t) and vC(t)v_C(t) change continuously over time while summing to E\mathcal{E}. When a problem relates one component voltage to another component voltage (such as vR=0.350vCv_R = 0.350 v_C), both must be expressed as time-dependent functions rather than referencing the fixed maximum initial voltage E\mathcal{E}.

REASONING PATH
Your ACEpath teacher’s suggested approach
Identify Reference Voltage
  • Always check whether a given percentage refers to the total supply voltage E\mathcal{E} or another changing component voltage in the circuit.

  • Write the exact condition vR(t)=k⋅vC(t)v_R(t) = k \cdot v_C(t) before replacing variables with formulas.

Use Kirchhoff's Voltage Law
  • For a series charging circuit, vR(t)+vC(t)=Ev_R(t) + v_C(t) = \mathcal{E}, so vC(t)=E−vR(t)=E(1−e−t/τ)v_C(t) = \mathcal{E} - v_R(t) = \mathcal{E}(1 - e^{-t/\tau}).

  • Substitute both vR(t)=Ee−t/τv_R(t) = \mathcal{E}e^{-t/\tau} and vC(t)=E(1−e−t/τ)v_C(t) = \mathcal{E}(1 - e^{-t/\tau}) into the condition to solve for e−t/τe^{-t/\tau}.

CORRECTED PATH
ACEpath Teacher's Demonstration
  1. Set up the given condition with both time-dependent voltages: vR(t)=0.350 vC(t)v_R(t) = 0.350 \, v_C(t).

  2. Substitute the expressions: Ee−t/τ=0.350[E(1−e−t/τ)]\mathcal{E} e^{-t/\tau} = 0.350 \left[\mathcal{E}(1 - e^{-t/\tau})\right].

  3. Divide by E\mathcal{E} and collect terms: e−t/τ(1+0.350)=0.350  ⟹  e−t/τ=0.3501.350=727e^{-t/\tau}(1 + 0.350) = 0.350 \implies e^{-t/\tau} = \frac{0.350}{1.350} = \frac{7}{27}.

  4. Solve for tt: t=−τln⁡(727)=1.23ln⁡(277)≈1.23×1.3499≈1.66 st = -\tau \ln\left(\frac{7}{27}\right) = 1.23 \ln\left(\frac{27}{7}\right) \approx 1.23 \times 1.3499 \approx 1.66\text{ s}.

Final answer

t=1.66 st = 1.66\text{ s}

NEXT STEPS
Final Takeaways from Your Teacher
  • Re-read problem statements carefully to distinguish between 'percent of initial/source voltage' and 'percent of capacitor voltage'.

  • Practice setting up ratio equations between vR(t)v_R(t) and vC(t)v_C(t) by applying vC(t)=E−vR(t)v_C(t) = \mathcal{E} - v_R(t) directly.

  • Check that your final time satisfies both component values: verify whether vR(t)/vC(t)v_R(t) / v_C(t) matches the given ratio at your calculated time.

OverviewACEpath Teacher's Diagnosis

02 The student swaps the transient behavior of the resistor and the capacitor, incorrectly using the charging form 1 - e^(-t/τ) for v_R(t) and the decaying form e^(-t/τ) for v_C(t).

Sample Student Work

Reviewed by ACEpath Teacher
Step-by-Step Review
Walk Through It with Your Teacher
Incorrect
  1. Step 1

    τ=RC=(82.0×103)(15.0×10−6)=1.23 s\tau = RC = (82.0 \times 10^3)(15.0 \times 10^{-6}) = 1.23\text{ s}

  2. Step 2

    vR(t)=E(1−e−t/τ)  ⟹  vC(t)=E⋅e−t/τv_R(t) = E(1 - e^{-t/\tau}) \implies v_C(t) = E \cdot e^{-t/\tau}

    Correct

    vR(t)=Ee−t/τandvC(t)=E(1−e−t/τ)v_R(t) = \mathcal{E} e^{-t/\tau} \quad \text{and} \quad v_C(t) = \mathcal{E}(1 - e^{-t/\tau})

    You swapped the transient voltage formulas. Because the capacitor is initially uncharged, its potential difference starts at 0 V0\text{ V} and rises as vC(t)=E(1−e−t/τ)v_C(t) = \mathcal{E}(1 - e^{-t/\tau}), while the resistor voltage starts at maximum E\mathcal{E} and decays as vR(t)=Ee−t/τv_R(t) = \mathcal{E} e^{-t/\tau}.

  3. Step 3

    E(1−e−t/τ)=0.350⋅E⋅e−t/τ  ⟹  1−e−t/τ=0.350⋅e−t/τ  ⟹  1.350⋅e−t/τ=1  ⟹  e−t/τ=11.350=2027E(1 - e^{-t/\tau}) = 0.350 \cdot E \cdot e^{-t/\tau} \implies 1 - e^{-t/\tau} = 0.350 \cdot e^{-t/\tau} \implies 1.350 \cdot e^{-t/\tau} = 1 \implies e^{-t/\tau} = \frac{1}{1.350} = \frac{20}{27}

    Correct

    Ee−t/τ=0.350[E(1−e−t/τ)]  ⟹  e−t/τ=0.350(1−e−t/τ)  ⟹  1.350e−t/τ=0.350  ⟹  e−t/τ=0.3501.350=727\mathcal{E} e^{-t/\tau} = 0.350 \left[\mathcal{E}(1 - e^{-t/\tau})\right] \implies e^{-t/\tau} = 0.350(1 - e^{-t/\tau}) \implies 1.350 e^{-t/\tau} = 0.350 \implies e^{-t/\tau} = \frac{0.350}{1.350} = \frac{7}{27}

    Your algebraic isolation of the exponential factor was carried out correctly, but it used the reversed expressions from Step 2.

  4. Step 4

    t=−1.23⋅ln⁡(2027)≈0.369 st = -1.23 \cdot \ln\left(\frac{20}{27}\right) \approx 0.369\text{ s}

    Correct

    t=−τln⁡(727)=(1.23 s)ln⁡(277)≈1.66 st = -\tau \ln\left(\frac{7}{27}\right) = (1.23\text{ s}) \ln\left(\frac{27}{7}\right) \approx 1.66\text{ s}

    Your logarithmic calculation and rounding were technically correct, but the numerical answer is incorrect due to the propagated equation swap.

WHAT YOU DID WELL
Compliments from Your Teacher

You calculated the capacitive time constant τ=RC\tau = RC accurately.

You translated the problem condition vR(t)=0.350vC(t)v_R(t) = 0.350 v_C(t) into an algebraic equation faithfully.

You handled the algebraic rearrangement and natural logarithm operations correctly.

THE ERROR
Where Your ACEpath Teacher Spotted the Mistake
Swapped RC Transient Response Formulas

no

WHY IT HAPPENED
ACEpath Teacher's Diagnosis

You assigned the rising transient response (1−e−t/τ)(1 - e^{-t/\tau}) to the resistor and the decaying exponential e−t/τe^{-t/\tau} to the capacitor, reversing their physical behaviors during DC charging.

REASONING PATH
Your ACEpath teacher’s suggested approach
Initial Boundary Condition ($t = 0$)
  • An uncharged capacitor has q(0)=0q(0) = 0, so its voltage must be vC(0)=0v_C(0) = 0.

  • Always test t=0t = 0: 1−e0=01 - e^0 = 0, which confirms that the factor (1−e−t/τ)(1 - e^{-t/\tau}) belongs to vC(t)v_C(t).

Resistor Voltage Decay
  • By Ohm's law, vR(t)=i(t)Rv_R(t) = i(t)R. Current is highest immediately after the switch closes and decays to zero as the capacitor charges.

  • Associate decaying exponential behavior e−t/τe^{-t/\tau} with circuit current i(t)i(t) and resistor voltage vR(t)v_R(t).

CORRECTED PATH
ACEpath Teacher's Demonstration
  1. Set up the correct transient functions for charging: vR(t)=Ee−t/τv_R(t) = \mathcal{E} e^{-t/\tau} and vC(t)=E(1−e−t/τ)v_C(t) = \mathcal{E}(1 - e^{-t/\tau}).

  2. Substitute into the given condition: Ee−t/τ=0.350E(1−e−t/τ)\mathcal{E} e^{-t/\tau} = 0.350 \mathcal{E} (1 - e^{-t/\tau}).

  3. Divide by E\mathcal{E} and collect terms: e−t/τ+0.350e−t/τ=0.350  ⟹  1.350e−t/τ=0.350e^{-t/\tau} + 0.350 e^{-t/\tau} = 0.350 \implies 1.350 e^{-t/\tau} = 0.350.

  4. Solve for the exponential factor: e−t/τ=0.3501.350=727e^{-t/\tau} = \frac{0.350}{1.350} = \frac{7}{27}.

  5. Solve for tt: t=−τln⁡(727)=(1.23 s)ln⁡(277)≈1.66 st = -\tau \ln\left(\frac{7}{27}\right) = (1.23\text{ s}) \ln\left(\frac{27}{7}\right) \approx 1.66\text{ s}.

Final answer

t=1.66 st = 1.66\text{ s}

NEXT STEPS
Final Takeaways from Your Teacher
  • Check your formulas at t=0t = 0 and t→∞t \to \infty before solving to verify that the boundary conditions match physical reality.

  • Review the dual relationship between capacitor voltage and resistor voltage given by Kirchhoff's Voltage Law: vR(t)+vC(t)=Ev_R(t) + v_C(t) = \mathcal{E}.

OverviewACEpath Teacher's Diagnosis

03 The student forgets to convert the microfarad capacitance unit to farads, using C = 15.0 instead of 15.0 × 10⁻⁶ F.

Sample Student Work

Reviewed by ACEpath Teacher
Step-by-Step Review
Walk Through It with Your Teacher
Partially correct
  1. Step 1

    τ=RC=(82.0×103)(15.0)=1.23×106 s\tau = RC = (82.0 \times 10^3)(15.0) = 1.23 \times 10^6\text{ s}

    Correct

    τ=RC=(82.0×103 Ω)(15.0×10−6 F)=1.23 s\tau = RC = (82.0 \times 10^3\text{ }\Omega)(15.0 \times 10^{-6}\text{ F}) = 1.23\text{ s}

    You converted 82.0 kΩ82.0\text{ k}\Omega to 82.0×103 Ω82.0 \times 10^3\text{ }\Omega, but you left C=15.0 μFC = 15.0\text{ }\mu\text{F} as 15.015.0 without converting microfarads to farads (1 μF=10−6 F1\text{ }\mu\text{F} = 10^{-6}\text{ F}).

  2. Step 2

    VR(t)=E⋅e−t/τ  ⟹  VC(t)=E(1−e−t/τ)V_R(t) = E \cdot e^{-t/\tau} \implies V_C(t) = E(1 - e^{-t/\tau})

  3. Step 3

    E⋅e−t/τ=0.350⋅E(1−e−t/τ)  ⟹  e−t/τ=0.350(1−e−t/τ)  ⟹  1.350⋅e−t/τ=0.350  ⟹  e−t/τ=727E \cdot e^{-t/\tau} = 0.350 \cdot E(1 - e^{-t/\tau}) \implies e^{-t/\tau} = 0.350(1 - e^{-t/\tau}) \implies 1.350 \cdot e^{-t/\tau} = 0.350 \implies e^{-t/\tau} = \frac{7}{27}

  4. Step 4

    t=τ⋅ln⁡(277)=(1.23×106)(1.350)≈1.66×106 st = \tau \cdot \ln\left(\frac{27}{7}\right) = (1.23 \times 10^6)(1.350) \approx 1.66 \times 10^6\text{ s}

    Correct

    t=τln⁡(277)=(1.23 s)(1.3499)≈1.66 st = \tau \ln\left(\frac{27}{7}\right) = (1.23\text{ s})(1.3499) \approx 1.66\text{ s}

    Your algebraic isolation of t=τln⁡(27/7)t = \tau \ln(27/7) was flawless, but substituting the incorrect value of τ\tau from Step 1 scaled your final answer by 10610^6.

WHAT YOU DID WELL
Compliments from Your Teacher

You correctly recalled and applied the transient voltage formulas for both the resistor and the capacitor.

You accurately formulated the condition vR(t)=0.350vC(t)v_R(t) = 0.350 v_C(t) rather than confusing vC(t)v_C(t) with the constant source EMF.

You performed clean algebraic manipulation to solve for the exponential factor and take the natural logarithm.

THE ERROR
Where Your ACEpath Teacher Spotted the Mistake
Unit Conversion Error

You converted the resistor value from kilo-ohms to ohms (82.0×103 Ω82.0 \times 10^3\text{ }\Omega), but forgot to include the metric prefix factor 10−610^{-6} for the capacitance given in microfarads (μF\mu\text{F}).

WHY IT HAPPENED
ACEpath Teacher's Diagnosis

Overlooking standard SI unit conversions for components with submultiple prefixes (like μF\mu\text{F} or nF\text{nF}) before calculating time constants.

REASONING PATH
Your ACEpath teacher’s suggested approach
Convert All Component Values to Base SI Units
  • The time constant τ=RC\tau = RC yields seconds only when RR is in ohms (Ω\Omega) and CC is in farads (F\text{F}), where 1 μF=10−6 F1\text{ }\mu\text{F} = 10^{-6}\text{ F}.

  • Always write down explicit unit conversion factors next to given values before inserting them into formulas.

Sanity Check Physical Time Scales
  • Typical laboratory RCRC circuits with kilo-ohm resistors and microfarad capacitors produce time constants on the order of seconds or fractions of a second, not mega-seconds.

  • Check whether an answer of 106 s10^6\text{ s} (over 1919 days) makes physical sense for a circuit with an 82 kΩ82\text{ k}\Omega resistor and a 15μF15\mu\text{F} capacitor.

CORRECTED PATH
ACEpath Teacher's Demonstration
  1. Convert capacitance to base SI units: C=15.0 μF=15.0×10−6 FC = 15.0\text{ }\mu\text{F} = 15.0 \times 10^{-6}\text{ F}.

  2. Calculate the correct time constant: τ=RC=(8.20×104 Ω)(1.50×10−5 F)=1.23 s\tau = RC = (8.20 \times 10^4\text{ }\Omega)(1.50 \times 10^{-5}\text{ F}) = 1.23\text{ s}.

  3. Evaluate elapsed time: t=τln⁡(277)=(1.23 s)(1.3499)≈1.66 st = \tau \ln\left(\frac{27}{7}\right) = (1.23\text{ s})(1.3499) \approx 1.66\text{ s}.

Final answer

t=1.66 st = 1.66\text{ s}

NEXT STEPS
Final Takeaways from Your Teacher
  • Review common metric prefix multipliers: micro (μ=10−6\mu = 10^{-6}), nano (extn=10−9 ext{n} = 10^{-9}), and pico (extp=10−12 ext{p} = 10^{-12}).

  • Practice performing a dimensional sanity check on intermediate values such as the time constant τ\tau before propagating them into downstream equations.

Lock it in

Similar question

01

A series RCRC circuit has τ=2.0 s\tau = 2.0\text{ s} and is connected to a DC source E\mathcal{E}. Find the time tt when the potential difference across the resistor equals the potential difference across the capacitor (vR(t)=vC(t)v_R(t) = v_C(t)).

Answer

t=1.39 st = 1.39\text{ s}. Condition: vR(t)=vC(t)  ⟹  e−t/τ=1−e−t/τ  ⟹  2e−t/τ=1  ⟹  e−t/τ=0.5v_R(t) = v_C(t) \implies e^{-t/\tau} = 1 - e^{-t/\tau} \implies 2e^{-t/\tau} = 1 \implies e^{-t/\tau} = 0.5. Therefore, t=τln⁡(2)=2.0 s⋅0.6931≈1.39 st = \tau \ln(2) = 2.0\text{ s} \cdot 0.6931 \approx 1.39\text{ s}.

02

A 10.0 V10.0\text{ V} DC supply charges an uncharged 20.0 μF20.0\text{ }\mu\text{F} capacitor through a 50.0 kΩ50.0\text{ k}\Omega resistor. How long after the switch is closed will the voltage across the capacitor be three times the voltage across the resistor?

Answer

t=1.39 st = 1.39\text{ s}. First, τ=RC=(5.00×104 Ω)(2.00×10−5 F)=1.00 s\tau = RC = (5.00 \times 10^4\,\Omega)(2.00 \times 10^{-5}\text{ F}) = 1.00\text{ s}. The condition vC(t)=3vR(t)v_C(t) = 3 v_R(t) means 1−e−t/τ=3e−t/τ  ⟹  4e−t/τ=1  ⟹  e−t/τ=0.251 - e^{-t/\tau} = 3 e^{-t/\tau} \implies 4 e^{-t/\tau} = 1 \implies e^{-t/\tau} = 0.25. Thus, t=τln⁡(4)=1.00⋅1.3863≈1.39 st = \tau \ln(4) = 1.00 \cdot 1.3863 \approx 1.39\text{ s}.

03

An uncharged capacitor charges in a series RCRC circuit with time constant τ=3.50 s\tau = 3.50\text{ s}. Determine the time tt at which the power dissipated by the resistor PR(t)P_R(t) decreases to 16.0%16.0\% of the power currently delivered by the source Psource(t)P_{\text{source}}(t).

Answer

t=6.42 st = 6.42\text{ s}. PR(t)=i(t)2R=i(t)vR(t)P_R(t) = i(t)^2 R = i(t) v_R(t) and Psource(t)=Ei(t)P_{\text{source}}(t) = \mathcal{E} i(t). Thus, PR/Psource=vR(t)/E=e−t/τP_R / P_{\text{source}} = v_R(t) / \mathcal{E} = e^{-t/\tau}. Setting e−t/τ=0.160e^{-t/\tau} = 0.160 gives t=−τln⁡(0.160)=3.50ln⁡(1/0.160)=3.50ln⁡(6.25)≈3.50×1.8326≈6.42 st = -\tau \ln(0.160) = 3.50 \ln(1/0.160) = 3.50 \ln(6.25) \approx 3.50 \times 1.8326 \approx 6.42\text{ s}.

Loading workspace…