Resources

An timing circuit on a micromachined sensor platform uses an integrated thin-film capacitor with capacitance C=820 pFC = 820\text{ pF} connected in series with a precision thick-film resistor of resistance R=4.70 MΩR = 4.70\text{ M}\Omega and a 3.30 V3.30\text{ V} supply rail. (a) Compute the circuit time constant τ\tau in milliseconds (ms\text{ms}). (b) Find the instantaneous rate of energy dissipation in the resistor in microwatts (μW\mu\text{W}) at t=2.50 mst = 2.50\text{ ms} after charging begins from zero initial charge.

Answer and steps

Final answer

(a) τ=3.85 ms\tau = 3.85\text{ ms}; (b) PR=0.621 μWP_R = 0.621\text{ }\mu\text{W}

Steps

01

Current as a Function of Time

Part (a): Calculating the Circuit Time Constant τ\tau

In a series resistor-capacitor (RCRC) circuit, the characteristic time constant τ\tau governs the rate at which the capacitor charges or discharges. It is defined as: τ=RC\tau = R C

  1. Convert the component values to standard SI units:
    • Resistance: R=4.70 MΩ=4.70×106 ΩR = 4.70\text{ M}\Omega = 4.70 \times 10^6\text{ }\Omega
    • Capacitance: C=820 pF=820×10−12 F=8.20×10−10 FC = 820\text{ pF} = 820 \times 10^{-12}\text{ F} = 8.20 \times 10^{-10}\text{ F}
  2. Compute τ\tau: τ=(4.70×106 Ω)⋅(8.20×10−10 F)=3.854×10−3 s\tau = (4.70 \times 10^6\text{ }\Omega) \cdot (8.20 \times 10^{-10}\text{ F}) = 3.854 \times 10^{-3}\text{ s} Expressed in milliseconds and rounded to three significant figures: τ=3.85 ms\tau = 3.85\text{ ms}

Part (b): Instantaneous Rate of Energy Dissipation in the Resistor

The instantaneous rate of energy dissipation in a resistor is the electrical power dissipated as heat, given by Joule's law: PR(t)=I(t)2R=VR(t)2RP_R(t) = I(t)^2 R = \frac{V_R(t)^2}{R}

When charging begins from zero initial charge (q(0)=0q(0) = 0), the capacitor initially acts like a short circuit, meaning the entire source voltage drops across the resistor at t=0t = 0:

I0=V0R=3.30 V4.70×106 Ω≈0.7021 μAI_0 = \frac{V_0}{R} = \frac{3.30\text{ V}}{4.70 \times 10^6\text{ }\Omega} \approx 0.7021\text{ }\mu\text{A}

As charge accumulates on the capacitor plates, the opposing voltage across the capacitor grows, causing the loop current to decay exponentially:

I(t)=I0e−t/τI(t) = I_0 e^{-t/\tau}

02

Evaluate the Current at t=2.50 mst = 2.50\text{ ms}

Using the time constant τ≈3.85 ms\tau \approx 3.85\text{ ms}:

tτ=2.50 ms3.85 ms≈0.649\frac{t}{\tau} = \frac{2.50\text{ ms}}{3.85\text{ ms}} \approx 0.649

The decay factor is:

e−t/τ≈e−0.649≈0.518e^{-t/\tau} \approx e^{-0.649} \approx 0.518

Thus, the instantaneous current through the circuit is:

I(2.50 ms)≈0.7021 μA⋅0.518≈0.3636 μAI(2.50\text{ ms}) \approx 0.7021\text{ }\mu\text{A} \cdot 0.518 \approx 0.3636\text{ }\mu\text{A}

03

Compute the Power Dissipation PRP_R

Substitute this current back into the power equation:

PR=I2R≈(0.3636×10−6 A)2⋅(4.70×106 Ω)≈0.621×10−6 W=0.621 μWP_R = I^2 R \approx (0.3636 \times 10^{-6}\text{ A})^2 \cdot (4.70 \times 10^6\text{ }\Omega) \approx 0.621 \times 10^{-6}\text{ W} = 0.621\text{ }\mu\text{W}

(Alternative check using voltage: VR(t)=V0e−t/τ≈3.30⋅0.518≈1.709 VV_R(t) = V_0 e^{-t/\tau} \approx 3.30 \cdot 0.518 \approx 1.709\text{ V}, yielding PR=VR2R=(1.709)24.70×106≈0.621 μWP_R = \frac{V_R^2}{R} = \frac{(1.709)^2}{4.70 \times 10^6} \approx 0.621\text{ }\mu\text{W}.)

Common Pitfall: Do not confuse the instantaneous rate of energy dissipation in the resistor (PR=I2RP_R = I^2 R) with the rate of energy storage in the capacitor (PC=IVCP_C = I V_C). While the voltage across the capacitor increases as VC(t)=V0(1−e−t/τ)V_C(t) = V_0(1 - e^{-t/\tau}), the resistor voltage and current decay according to e−t/τe^{-t/\tau}. Consequently, power dissipation in the resistor decays twice as fast as the current, proportional to e−2t/τe^{-2t/\tau}.

Typical errors

OverviewACEpath Teacher's Diagnosis

01 The student forgets to square the exponential factor when calculating power from current, using e^(-t/τ) instead of e^(-2t/τ), resulting in 1.21 μW.

Sample Student Work

Reviewed by ACEpath Teacher
Step-by-Step Review
Walk Through It with Your Teacher
Partially correct
  1. Step 1

    τ=R⋅C  ⟹  τ=(4.70×106 Ω)⋅(820×10−12 F)=3.854×10−3 s  ⟹  τ=3.85 ms\tau = R \cdot C \implies \tau = (4.70 \times 10^6\,\Omega) \cdot (820 \times 10^{-12}\text{ F}) = 3.854 \times 10^{-3}\text{ s} \implies \tau = 3.85\text{ ms}

  2. Step 2

    P=(V2R)⋅e−(t/τ)P = \left(\frac{V^2}{R}\right) \cdot e^{-(t/\tau)}

    Correct

    PR(t)=VR(t)2R=(V0e−t/τ)2R=V02Re−2t/τP_R(t) = \frac{V_R(t)^2}{R} = \frac{(V_0 e^{-t/\tau})^2}{R} = \frac{V_0^2}{R} e^{-2t/\tau}

    Because instantaneous power depends quadratically on voltage or current (P=VR2R=I2RP = \frac{V_R^2}{R} = I^2 R), squaring e−t/τe^{-t/\tau} results in an exponential decay factor of e−2t/τe^{-2t/\tau}.

  3. Step 3

    V2R=(3.30)24.70×106=2.317×10−6 W=2.317 μW\frac{V^2}{R} = \frac{(3.30)^2}{4.70 \times 10^6} = 2.317 \times 10^{-6}\text{ W} = 2.317\,\mu\text{W}

  4. Step 4

    P=2.317⋅e−(2.50/3.854)  ⟹  P=2.317⋅0.5228=1.21 μWP = 2.317 \cdot e^{-(2.50 / 3.854)} \implies P = 2.317 \cdot 0.5228 = 1.21\,\mu\text{W}

    Correct

    PR(2.50 ms)=2.317 μW⋅e−2(2.50/3.854)=2.317 μW⋅(0.5228)2≈0.621 μWP_R(2.50\text{ ms}) = 2.317\,\mu\text{W} \cdot e^{-2(2.50 / 3.854)} = 2.317\,\mu\text{W} \cdot (0.5228)^2 \approx 0.621\,\mu\text{W}

    Your arithmetic evaluation was carried out correctly based on your formula, but the result is incorrect due to the missing factor of 2 in the exponent.

WHAT YOU DID WELL
Compliments from Your Teacher

You correctly calculated the time constant using τ=RC\tau = RC with proper unit conversions.

You correctly recognized that the resistor voltage decays exponentially from the supply voltage.

You calculated the initial maximum resistor power V02R\frac{V_0^2}{R} accurately.

THE ERROR
Where Your ACEpath Teacher Spotted the Mistake
Omission of quadratic exponent scaling in power calculation

You applied the first-order exponential decay factor e−t/τe^{-t/\tau} directly to power instead of squaring it.

WHY IT HAPPENED
ACEpath Teacher's Diagnosis

Confusing the time dependence of linear circuit variables (current and voltage, which decay as e−t/τe^{-t/\tau}) with quadratic variables (power and energy dissipation rate, which scale as (e−t/τ)2=e−2t/τ(e^{-t/\tau})^2 = e^{-2t/\tau}).

REASONING PATH
Your ACEpath teacher’s suggested approach
Quadratic dependence of electrical power
  • Power in a linear resistor satisfies P(t)=I(t)2R=V(t)2RP(t) = I(t)^2 R = \frac{V(t)^2}{R}.

  • Always write the fundamental definition in terms of V(t)V(t) or I(t)I(t) first, then substitute the decaying term and square both the amplitude and the exponential factor.

Exponent rule for powers of exponentials
  • (eu)2=e2u\left(e^{u}\right)^2 = e^{2u}.

  • Ensure that (e−t/τ)2(e^{-t/\tau})^2 is rewritten as e−2t/τe^{-2t/\tau}, meaning power decays with an effective time constant of τ2\frac{\tau}{2}.

CORRECTED PATH
ACEpath Teacher's Demonstration
  1. Write the instantaneous resistor power as PR(t)=VR(t)2R=(V0e−t/τ)2R=V02Re−2t/τP_R(t) = \frac{V_R(t)^2}{R} = \frac{(V_0 e^{-t/\tau})^2}{R} = \frac{V_0^2}{R} e^{-2t/\tau}.

  2. Substitute the peak power P0=2.317 μWP_0 = 2.317\,\mu\text{W} and the ratio tτ=2.50 ms3.854 ms≈0.6487\frac{t}{\tau} = \frac{2.50\text{ ms}}{3.854\text{ ms}} \approx 0.6487.

  3. Compute the squared decay factor: e−2(0.6487)=e−1.2974≈0.2678e^{-2(0.6487)} = e^{-1.2974} \approx 0.2678 (or (0.5228)2≈0.2733(0.5228)^2 \approx 0.2733).

  4. Multiply to find the final power: PR=2.317 μW×0.2678≈0.621 μWP_R = 2.317\,\mu\text{W} \times 0.2678 \approx 0.621\,\mu\text{W}.

Final answer

0.621 μW0.621\,\mu\text{W}

NEXT STEPS
Final Takeaways from Your Teacher
  • Review the distinction between quantities that decay as e−t/τe^{-t/\tau} (II, VRV_R) and their squares that decay as e−2t/τe^{-2t/\tau} (PRP_R).

  • Practice deriving instantaneous power directly from I(t)2RI(t)^2 R to make squaring the current an automatic step.

OverviewACEpath Teacher's Diagnosis

02 The student misinterprets the prefix pico as 10⁻⁹ instead of 10⁻¹², calculating a time constant that is off by a factor of 1000 and propagating it into the power calculation.

Sample Student Work

Reviewed by ACEpath Teacher
Step-by-Step Review
Walk Through It with Your Teacher
Partially correct
  1. Step 1

    C=820×10−9 FC = 820 \times 10^{-9}\text{ F}

    Correct

    C=820 pF=820×10−12 F=8.20×10−10 FC = 820\text{ pF} = 820 \times 10^{-12}\text{ F} = 8.20 \times 10^{-10}\text{ F}

    You converted the prefix pico (p\text{p}) as 10−910^{-9}, which represents nano (n\text{n}). Pico represents 10−1210^{-12}, so 820 pF=820×10−12 F820\text{ pF} = 820 \times 10^{-12}\text{ F}.

  2. Step 2

    τ=R⋅C=(4.70×106)⋅(820×10−9)⟹τ=3.854 s=3854 ms\tau = R \cdot C = (4.70 \times 10^6) \cdot (820 \times 10^{-9}) \Longrightarrow \tau = 3.854\text{ s} = 3854\text{ ms}

    Correct

    τ=RC=(4.70×106 Ω)(8.20×10−10 F)=3.854×10−3 s=3.85 ms\tau = R C = (4.70 \times 10^6\text{ }\Omega)(8.20 \times 10^{-10}\text{ F}) = 3.854 \times 10^{-3}\text{ s} = 3.85\text{ ms}

    You correctly multiplied resistance by capacitance, but your result was inflated by a factor of 10310^3 due to the earlier conversion error.

  3. Step 3

    P=(V2R)⋅e−2t/τP = \left(\frac{V^2}{R}\right) \cdot e^{-2t/\tau}

  4. Step 4

    P=((3.30)24.70×106)⋅e(−2⋅2.50/3854)⟹P=2.317×10−6⋅0.9987=2.31 μWP = \left(\frac{(3.30)^2}{4.70 \times 10^6}\right) \cdot e^{(-2 \cdot 2.50 / 3854)} \Longrightarrow P = 2.317 \times 10^{-6} \cdot 0.9987 = 2.31\text{ }\mu\text{W}

    Correct

    PR(2.50 ms)=(3.30 V)24.70×106 Ωe−2(2.50 ms)/(3.854 ms)≈2.315×10−6×0.2732≈0.621 μWP_R(2.50\text{ ms}) = \frac{(3.30\text{ V})^2}{4.70 \times 10^6\text{ }\Omega} e^{-2(2.50\text{ ms})/(3.854\text{ ms})} \approx 2.315 \times 10^{-6} \times 0.2732 \approx 0.621\text{ }\mu\text{W}

    Your algebraic substitution and arithmetic were carried out properly, but substituting τ=3854 ms\tau = 3854\text{ ms} instead of 3.854 ms3.854\text{ ms} caused the exponential decay factor to be nearly 11 instead of 0.2730.273.

WHAT YOU DID WELL
Compliments from Your Teacher

You selected and applied the correct formula for the RC circuit time constant, τ=RC\tau = RC.

You correctly derived the resistor power formula P(t)=V2Re−2t/τP(t) = \frac{V^2}{R}e^{-2t/\tau} by squaring the decaying exponential term.

You performed all downstream arithmetic operations accurately according to your substituted values.

THE ERROR
Where Your ACEpath Teacher Spotted the Mistake
Metric prefix confusion (pico vs nano)

You wrote 10−910^{-9} instead of 10−1210^{-12} for the prefix pico (p\text{p}).

WHY IT HAPPENED
ACEpath Teacher's Diagnosis

Confusing the SI metric submultiple prefixes 'nano-' (10−910^{-9}) and 'pico-' (10−1210^{-12}) during unit conversion before substituting into the formulas.

REASONING PATH
Your ACEpath teacher’s suggested approach
Sub-micro Metric Prefixes
  • milli (m)=10−3\text{milli } (\text{m}) = 10^{-3}, micro (μ)=10−6\text{micro } (\mu) = 10^{-6}, nano (n)=10−9\text{nano } (\text{n}) = 10^{-9}, pico (p)=10−12\text{pico } (\text{p}) = 10^{-12}, femto (f)=10−15\text{femto } (\text{f}) = 10^{-15}.

  • Always verify component prefix steps: each subsequent prefix step (m, μ\mu, n, p) shifts the power of ten by a factor of 10−310^{-3}.

CORRECTED PATH
ACEpath Teacher's Demonstration
  1. Recalculate the time constant with the corrected capacitance C=820×10−12 FC = 820 \times 10^{-12}\text{ F}: τ=(4.70×106 Ω)(820×10−12 F)=3.854×10−3 s=3.854 ms\tau = (4.70 \times 10^6\text{ }\Omega)(820 \times 10^{-12}\text{ F}) = 3.854 \times 10^{-3}\text{ s} = 3.854\text{ ms}.

  2. Evaluate the exponential factor at t=2.50 mst = 2.50\text{ ms}: −2tτ=−2×2.50 ms3.854 ms≈−1.297-\frac{2t}{\tau} = -\frac{2 \times 2.50\text{ ms}}{3.854\text{ ms}} \approx -1.297.

  3. Compute the decay multiplier: e−1.297≈0.2732e^{-1.297} \approx 0.2732.

  4. Compute the initial peak power: P0=V2R=(3.30)24.70×106≈2.315×10−6 W=2.315 μWP_0 = \frac{V^2}{R} = \frac{(3.30)^2}{4.70 \times 10^6} \approx 2.315 \times 10^{-6}\text{ W} = 2.315\text{ }\mu\text{W}.

  5. Multiply to find the final instantaneous power: PR=2.315 μW×0.2732≈0.621 μWP_R = 2.315\text{ }\mu\text{W} \times 0.2732 \approx 0.621\text{ }\mu\text{W}.

Final answer

(a) τ=3.85 ms\tau = 3.85\text{ ms}; (b) PR=0.621 μWP_R = 0.621\text{ }\mu\text{W}

NEXT STEPS
Final Takeaways from Your Teacher
  • Create a quick reference table of sub-micro metric prefixes (10−310^{-3}, 10−610^{-6}, 10−910^{-9}, 10−1210^{-12}) and review it before solving circuit problems.

  • Perform a quick sanity check on timing values: picofarad capacitors paired with megohm resistors typically yield time constants in the millisecond range, not multiple seconds.

  • Practice identifying the time constant τ\tau and its impact on the decay factor e−t/τe^{-t/\tau} across different component scales.

OverviewACEpath Teacher's Diagnosis

03 The student uses the capacitor voltage formula (1 - e^(-t/τ)) instead of the resistor decay formula to compute the power dissipated by the resistor, obtaining 1.68 μW.

Sample Student Work

Reviewed by ACEpath Teacher
Step-by-Step Review
Walk Through It with Your Teacher
Partially correct
  1. Step 1

    τ=R⋅C=(4.70×106)(820×10−12)  ⟹  τ=3.85 ms\tau = R \cdot C = (4.70 \times 10^6)(820 \times 10^{-12}) \implies \tau = 3.85\text{ ms}

  2. Step 2

    VR=V(1−e−t/τ)  ⟹  VR=3.30(1−e−2.50/3.854)=3.30(1−0.5228)=1.575 VV_R = V(1 - e^{-t/\tau}) \implies V_R = 3.30(1 - e^{-2.50/3.854}) = 3.30(1 - 0.5228) = 1.575\text{ V}

    Correct

    VR(t)=V0e−t/τ=3.30e−2.50/3.854≈3.30(0.5228)≈1.725 VV_R(t) = V_0 e^{-t/\tau} = 3.30 e^{-2.50/3.854} \approx 3.30(0.5228) \approx 1.725\text{ V}

    In an RCRC charging circuit, the current and the resistor voltage start at their maximum values and decay exponentially as VR(t)=V0e−t/τV_R(t) = V_0 e^{-t/\tau}. The factor (1−e−t/τ)(1 - e^{-t/\tau}) describes the voltage across the charging capacitor, VC(t)V_C(t), not the resistor.

  3. Step 3

    P=VR2R=(1.575)24.70×106  ⟹  P=5.28×10−7 W=0.528 μWP = \frac{V_R^2}{R} = \frac{(1.575)^2}{4.70 \times 10^6} \implies P = 5.28 \times 10^{-7}\text{ W} = 0.528\text{ }\mu\text{W}

    Correct

    PR=VR2R=(1.725 V)24.70×106 Ω≈0.621 μWP_R = \frac{V_R^2}{R} = \frac{(1.725\text{ V})^2}{4.70 \times 10^6\text{ }\Omega} \approx 0.621\text{ }\mu\text{W}

    You correctly applied Joule's law P=VR2RP = \frac{V_R^2}{R}, but your final numerical value was affected by the incorrect resistor voltage from the previous step.

WHAT YOU DID WELL
Compliments from Your Teacher

You correctly calculated the time constant τ=RC\tau = RC using proper SI unit conversions.

You correctly identified and applied Joule's power dissipation law P=V2RP = \frac{V^2}{R}.

THE ERROR
Where Your ACEpath Teacher Spotted the Mistake
Wrong Voltage Decay Formula

You swapped the transient voltage expression of the capacitor with that of the resistor.

WHY IT HAPPENED
ACEpath Teacher's Diagnosis

Confusing the complementary time-dependent responses in an RCRC series circuit: as a capacitor charges, its voltage rises according to (1−e−t/τ)(1 - e^{-t/\tau}), while the circuit current and resistor voltage decay according to e−t/τe^{-t/\tau}.

REASONING PATH
Your ACEpath teacher’s suggested approach
Check Boundary Conditions at $t = 0$
  • At t=0+t = 0^+ with an uncharged capacitor, VC(0)=0 VV_C(0) = 0\text{ V} and VR(0)=V0V_R(0) = V_0.

  • Evaluate your formula at t=0t = 0: 1−e0=01 - e^0 = 0, which gives zero voltage across the resistor at the start. Since an uncharged capacitor acts as a short circuit, the initial resistor voltage must be maximum (V0V_0), confirming the factor should be e−t/τe^{-t/\tau}.

Resistor Voltage Follows Circuit Current
  • By Ohm's law, VR(t)=I(t)RV_R(t) = I(t) R.

  • Remember that current decays as the capacitor fills up with charge (I(t)=I0e−t/τI(t) = I_0 e^{-t/\tau}), so VR(t)V_R(t) must also decay directly with e−t/τe^{-t/\tau}.

CORRECTED PATH
ACEpath Teacher's Demonstration
  1. Compute the decay exponential factor: e−t/τ=e−2.50 ms/3.854 ms≈0.5228e^{-t/\tau} = e^{-2.50\text{ ms} / 3.854\text{ ms}} \approx 0.5228.

  2. Find the correct instantaneous resistor voltage: VR=3.30 V×0.5228≈1.725 VV_R = 3.30\text{ V} \times 0.5228 \approx 1.725\text{ V}.

  3. Substitute VRV_R into Joule's power formula: PR=VR2R=(1.725 V)24.70×106 Ω≈0.621 μWP_R = \frac{V_R^2}{R} = \frac{(1.725\text{ V})^2}{4.70 \times 10^6\text{ }\Omega} \approx 0.621\text{ }\mu\text{W}.

Final answer

(a) τ=3.85 ms\tau = 3.85\text{ ms}; (b) PR=0.621 μWP_R = 0.621\text{ }\mu\text{W}

NEXT STEPS
Final Takeaways from Your Teacher
  • Always test your transient voltage formulas at t=0t = 0 and t→∞t \to \infty to verify they match physical boundary conditions.

  • Practice distinguishing between quantities that grow toward steady state (like VCV_C and qq) versus quantities that decay toward zero (like II and VRV_R) during capacitor charging.

Lock it in

Similar question

01

A 2.00 μF2.00\,\mu\text{F} capacitor is charged to 10.0 V10.0\text{ V} and then discharged through a 50.0 kΩ50.0\text{ k}\Omega resistor. Calculate the instantaneous rate of energy dissipation in the resistor at t=100 mst = 100\text{ ms}.

Answer

τ=RC=(50.0×103 Ω)(2.00×10−6 F)=0.100 s=100 ms\tau = R C = (50.0 \times 10^3\,\Omega)(2.00 \times 10^{-6}\text{ F}) = 0.100\text{ s} = 100\text{ ms}. At t=τt = \tau, the initial power is P0=V02R=10050000=2.00 mWP_0 = \frac{V_0^2}{R} = \frac{100}{50000} = 2.00\text{ mW}. Since P(t)=P0e−2t/τP(t) = P_0 e^{-2t/\tau}, at t=τt = \tau we have P(τ)=2.00 mW⋅e−2≈2.00⋅0.1353=0.271 mWP(\tau) = 2.00\text{ mW} \cdot e^{-2} \approx 2.00 \cdot 0.1353 = 0.271\text{ mW} (271 μW271\,\mu\text{W}).

02

In a series RCRC charging circuit with Vsupply=5.0 VV_{\text{supply}} = 5.0\text{ V}, R=1.0 MΩR = 1.0\text{ M}\Omega, and C=10 μFC = 10\,\mu\text{F}, at what time tt will the rate of energy dissipation in the resistor drop to exactly 10%10\% of its initial value?

Answer

τ=RC=(1.0×106 Ω)(10×10−6 F)=10 s\tau = R C = (1.0 \times 10^6\,\Omega)(10 \times 10^{-6}\text{ F}) = 10\text{ s}. The power relationship is P(t)P0=e−2t/τ=0.10\frac{P(t)}{P_0} = e^{-2t/\tau} = 0.10. Taking the natural logarithm: −2t/τ=ln⁡(0.10)≈−2.3026-2t/\tau = \ln(0.10) \approx -2.3026, so t=2.3026⋅10 s2≈11.5 st = \frac{2.3026 \cdot 10\text{ s}}{2} \approx 11.5\text{ s}.

03

Show that the total thermal energy EdissE_{\text{diss}} dissipated in the resistor of an RCRC circuit discharging from an initial voltage V0V_0 equals the total initial electrostatic energy 12CV02\frac{1}{2} C V_0^2 stored in the capacitor by integrating the instantaneous power PR(t)=V02Re−2t/(RC)P_R(t) = \frac{V_0^2}{R} e^{-2t/(RC)} from t=0t = 0 to t=∞t = \infty.

Answer

Ediss=∫0∞PR(t) dt=V02R∫0∞e−2t/(RC) dt=V02R[−RC2e−2t/(RC)]0∞=V02R(0−(−RC2))=12CV02E_{\text{diss}} = \int_0^\infty P_R(t)\,dt = \frac{V_0^2}{R} \int_0^\infty e^{-2t/(RC)}\,dt = \frac{V_0^2}{R} \left[ -\frac{RC}{2} e^{-2t/(RC)} \right]_0^\infty = \frac{V_0^2}{R} \left( 0 - \left(-\frac{RC}{2}\right) \right) = \frac{1}{2} C V_0^2. Notice that the factor of 22 in the exponent directly yields the required 12\frac{1}{2} prefactor upon integration.

Loading workspace…