Resources

In a physics laboratory experiment using a magnetic force balance, a horizontal conducting foil strip of active length L=0.100 mL = 0.100\text{ m} is positioned in the uniform horizontal gap field between the pole faces of an electromagnet, oriented perpendicular to B⃗\vec{B}. The current II through the strip is adjusted across four trials, and the resulting magnetic force FBF_B is measured using an electronic analytical scale (measuring apparent mass change Δm\Delta m, where FB=Δm⋅gF_B = \Delta m \cdot g with g=9.80 m/s2g = 9.80\text{ m/s}^2): Trial 1: I=1.00 AI = 1.00\text{ A}, FB=0.048 NF_B = 0.048\text{ N}; Trial 2: I=2.00 AI = 2.00\text{ A}, FB=0.095 NF_B = 0.095\text{ N}; Trial 3: I=3.00 AI = 3.00\text{ A}, FB=0.144 NF_B = 0.144\text{ N}; Trial 4: I=4.00 AI = 4.00\text{ A}, FB=0.191 NF_B = 0.191\text{ N}. Using linear regression or slope analysis (FBF_B vs. II), determine the experimental value of the magnetic field strength BexpB_{\text{exp}} in the magnet gap.

Answer and steps

Final answer

Bexp=0.478 TB_{\text{exp}} = 0.478\text{ T}

Steps

01

Theoretical Relationship

The magnetic force F⃗B\vec{F}_B acting on a straight conductor of length LL carrying a current II in a uniform magnetic field B⃗\vec{B} is given by:

FB=ILBsin⁡θF_B = I L B \sin\theta

Since the strip is oriented perpendicular to the magnetic field, θ=90∘\theta = 90^\circ and sin⁡90∘=1\sin 90^\circ = 1. The expression simplifies to:

FB=(LB)IF_B = (L B) I

This represents a linear relationship of the form y=mx+cy = m x + c, where:

  • The dependent variable is y=FBy = F_B
  • The independent variable is x=Ix = I
  • The theoretical slope is m=LBm = L B
  • The theoretical intercept is c=0c = 0
02

Linear Regression (Slope Analysis)

Using the standard least-squares slope formula for N=4N = 4 data points:

m=∑i=1N(Ii−Iˉ)(FB,i−FˉB)∑i=1N(Ii−Iˉ)2m = \frac{\sum_{i=1}^N (I_i - \bar{I})(F_{B,i} - \bar{F}_B)}{\sum_{i=1}^N (I_i - \bar{I})^2}

First, compute the mean values of the current Iˉ\bar{I} and force FˉB\bar{F}_B:

Iˉ=1.00+2.00+3.00+4.004=2.50 A\bar{I} = \frac{1.00 + 2.00 + 3.00 + 4.00}{4} = 2.50\text{ A}

FˉB=0.048+0.095+0.144+0.1914=0.4784=0.1195 N\bar{F}_B = \frac{0.048 + 0.095 + 0.144 + 0.191}{4} = \frac{0.478}{4} = 0.1195\text{ N}

Next, calculate the deviations and terms for each trial:

  • For I1=1.00 AI_1 = 1.00\text{ A}, FB,1=0.048 NF_{B,1} = 0.048\text{ N}: (I1−Iˉ)=−1.50 A,(I1−Iˉ)2=2.25 A2(I_1 - \bar{I}) = -1.50\text{ A}, \quad (I_1 - \bar{I})^2 = 2.25\text{ A}^2 (I1−Iˉ)FB,1=(−1.50)(0.048)=−0.0720 N⋅A(I_1 - \bar{I}) F_{B,1} = (-1.50)(0.048) = -0.0720\text{ N}\cdot\text{A}
  • For I2=2.00 AI_2 = 2.00\text{ A}, FB,2=0.095 NF_{B,2} = 0.095\text{ N}: (I2−Iˉ)=−0.50 A,(I2−Iˉ)2=0.25 A2(I_2 - \bar{I}) = -0.50\text{ A}, \quad (I_2 - \bar{I})^2 = 0.25\text{ A}^2 (I2−Iˉ)FB,2=(−0.50)(0.095)=−0.0475 N⋅A(I_2 - \bar{I}) F_{B,2} = (-0.50)(0.095) = -0.0475\text{ N}\cdot\text{A}
  • For I3=3.00 AI_3 = 3.00\text{ A}, FB,3=0.144 NF_{B,3} = 0.144\text{ N}: (I3−Iˉ)=+0.50 A,(I3−Iˉ)2=0.25 A2(I_3 - \bar{I}) = +0.50\text{ A}, \quad (I_3 - \bar{I})^2 = 0.25\text{ A}^2 (I3−Iˉ)FB,3=(+0.50)(0.144)=+0.0720 N⋅A(I_3 - \bar{I}) F_{B,3} = (+0.50)(0.144) = +0.0720\text{ N}\cdot\text{A}
  • For I4=4.00 AI_4 = 4.00\text{ A}, FB,4=0.191 NF_{B,4} = 0.191\text{ N}: (I4−Iˉ)=+1.50 A,(I4−Iˉ)2=2.25 A2(I_4 - \bar{I}) = +1.50\text{ A}, \quad (I_4 - \bar{I})^2 = 2.25\text{ A}^2 (I4−Iˉ)FB,4=(+1.50)(0.191)=+0.2865 N⋅A(I_4 - \bar{I}) F_{B,4} = (+1.50)(0.191) = +0.2865\text{ N}\cdot\text{A}

Sum the squared deviations and cross-products:

∑i=14(Ii−Iˉ)2=2.25+0.25+0.25+2.25=5.00 A2\sum_{i=1}^4 (I_i - \bar{I})^2 = 2.25 + 0.25 + 0.25 + 2.25 = 5.00\text{ A}^2

∑i=14(Ii−Iˉ)(FB,i−FˉB)=∑i=14(Ii−Iˉ)FB,i=−0.0720−0.0475+0.0720+0.2865=0.2390 N⋅A\sum_{i=1}^4 (I_i - \bar{I})(F_{B,i} - \bar{F}_B) = \sum_{i=1}^4 (I_i - \bar{I}) F_{B,i} = -0.0720 - 0.0475 + 0.0720 + 0.2865 = 0.2390\text{ N}\cdot\text{A}

Calculate the slope:

m=0.2390 N⋅A5.00 A2=0.0478 N/Am = \frac{0.2390\text{ N}\cdot\text{A}}{5.00\text{ A}^2} = 0.0478\text{ N/A}

03

Calculating the Magnetic Field Strength BexpB_{\text{exp}}

Equating the experimental slope to the theoretical coefficient LBL B:

slope=L⋅Bexp\text{slope} = L \cdot B_{\text{exp}}

Bexp=slopeL=0.0478 N/A0.100 m=0.478 TB_{\text{exp}} = \frac{\text{slope}}{L} = \frac{0.0478\text{ N/A}}{0.100\text{ m}} = 0.478\text{ T}

Typical errors

OverviewACEpath Teacher's Diagnosis

01 The student forgets that slope = L B and incorrectly equates the slope directly to the magnetic field B without dividing by the active length L.

Sample Student Work

Reviewed by ACEpath Teacher
Step-by-Step Review
Walk Through It with Your Teacher
Incorrect
  1. Step 1

    FB=ILBF_B = I L B

  2. Step 2

    slope=0.191−0.0484.00−1.00=0.1433.00=0.0477 N/A\text{slope} = \frac{0.191 - 0.048}{4.00 - 1.00} = \frac{0.143}{3.00} = 0.0477\text{ N/A}

  3. Step 3

    Bexp=slope=0.0477 TB_{\text{exp}} = \text{slope} = 0.0477\text{ T}

    Correct

    Bexp=slopeL=0.0478 N/A0.100 m=0.478 TB_{\text{exp}} = \frac{\text{slope}}{L} = \frac{0.0478\text{ N/A}}{0.100\text{ m}} = 0.478\text{ T}

    In the linear model FB=(LB)IF_B = (L B) I, the slope equals the product LBL B, not BB alone. To find BexpB_{\text{exp}}, you must divide the slope by the length L=0.100 mL = 0.100\text{ m}.

WHAT YOU DID WELL
Compliments from Your Teacher

You recalled the correct formula for the magnetic force on a current-carrying wire.

You correctly set up a slope ratio of force change over current change.

THE ERROR
Where Your ACEpath Teacher Spotted the Mistake
Missing Parameter in Slope Interpretation

You treated the slope of the FBF_B vs. II graph as BB rather than LBL B.

WHY IT HAPPENED
ACEpath Teacher's Diagnosis

Confusing the physical slope of a graphed equation with a single target variable rather than matching the full coefficient of the independent variable (y=mx  ⟹  m=LBy = mx \implies m = LB).

REASONING PATH
Your ACEpath teacher’s suggested approach
Match the Linear Model
  • For y=mxy = m x, isolate the independent variable xx and set the slope mm equal to all remaining constant factors.

  • Write FB=(LB)⋅IF_B = (L B) \cdot I, identify that slope=LB\text{slope} = L B, and solve for B=slopeLB = \frac{\text{slope}}{L} before substituting values.

CORRECTED PATH
ACEpath Teacher's Demonstration
  1. Set the experimental slope equal to the theoretical slope: slope=L⋅Bexp\text{slope} = L \cdot B_{\text{exp}}.

  2. Solve for the magnetic field: Bexp=slopeLB_{\text{exp}} = \frac{\text{slope}}{L}.

  3. Substitute L=0.100 mL = 0.100\text{ m}: Bexp=0.0478 N/A0.100 m=0.478 TB_{\text{exp}} = \frac{0.0478\text{ N/A}}{0.100\text{ m}} = 0.478\text{ T}.

Final answer

Bexp=0.478 TB_{\text{exp}} = 0.478\text{ T}

NEXT STEPS
Final Takeaways from Your Teacher
  • Always explicitly match physical equations to y=mx+cy = mx + c by grouping all constant multipliers in parentheses in front of the independent variable.

  • Check units at the end: the slope has units of N/A\text{N/A}, whereas magnetic field requires T=N/(A⋅m)\text{T} = \text{N}/(\text{A}\cdot\text{m}), indicating division by a length is necessary.

OverviewACEpath Teacher's Diagnosis

02 The student multiplies the slope by L instead of dividing by L when solving for B from slope = L B.

Sample Student Work

Reviewed by ACEpath Teacher
Step-by-Step Review
Walk Through It with Your Teacher
Incorrect
  1. Step 1

    slope=0.191−0.0484.00−1.00=0.0477 N/A\text{slope} = \frac{0.191 - 0.048}{4.00 - 1.00} = 0.0477\text{ N/A}

  2. Step 2

    slope=LB\text{slope} = L B

  3. Step 3

    Bexp=slope⋅L=0.0477⋅0.100=0.00477 TB_{\text{exp}} = \text{slope} \cdot L = 0.0477 \cdot 0.100 = 0.00477\text{ T}

    Correct

    Bexp=slopeL=0.0478 N/A0.100 m=0.478 T(or 0.04770.100=0.477 T)B_{\text{exp}} = \frac{\text{slope}}{L} = \frac{0.0478\text{ N/A}}{0.100\text{ m}} = 0.478\text{ T} \quad \left(\text{or } \frac{0.0477}{0.100} = 0.477\text{ T}\right)

    You multiplied the slope by LL instead of dividing by LL. Rearranging slope=LB\text{slope} = L B requires isolating BB by dividing both sides by LL.

WHAT YOU DID WELL
Compliments from Your Teacher

You calculated a consistent slope for the magnetic force versus current data.

You correctly matched the experimental slope to the theoretical formula coefficient LBL B.

THE ERROR
Where Your ACEpath Teacher Spotted the Mistake
Algebraic isolation error (multiplication instead of division)

You accidentally multiplied by LL instead of dividing by LL when isolating BB.

WHY IT HAPPENED
ACEpath Teacher's Diagnosis

Inverting the algebraic operation when isolating a factor from a product y=kxy = k x: dividing by the known coefficient is required to isolate the unknown variable.

REASONING PATH
Your ACEpath teacher’s suggested approach
Isolating Factors in a Product
  • When A=B⋅CA = B \cdot C, solving for BB yields B=ACB = \frac{A}{C}, not B=A⋅CB = A \cdot C.

  • Always perform the inverse operation to isolate a variable: divide both sides by the multiplying constant.

Dimensional Unit Check
  • Magnetic field strength has units of T=NA⋅m\text{T} = \frac{\text{N}}{\text{A}\cdot\text{m}}.

  • Check whether your isolated expression produces the target unit: N/Am=T\frac{\text{N/A}}{\text{m}} = \text{T}, whereas (N/A)⋅m=J/A≠T(\text{N/A}) \cdot \text{m} = \text{J/A} \neq \text{T}.

CORRECTED PATH
ACEpath Teacher's Demonstration
  1. Start from the theoretical slope relation: slope=L⋅Bexp\text{slope} = L \cdot B_{\text{exp}}

  2. Divide both sides by LL to isolate BexpB_{\text{exp}}: Bexp=slopeLB_{\text{exp}} = \frac{\text{slope}}{L}

  3. Substitute slope=0.0478 N/A\text{slope} = 0.0478\text{ N/A} (or 0.0477 N/A0.0477\text{ N/A}) and L=0.100 mL = 0.100\text{ m}: Bexp=0.0478 N/A0.100 m=0.478 TB_{\text{exp}} = \frac{0.0478\text{ N/A}}{0.100\text{ m}} = 0.478\text{ T}

Final answer

Bexp=0.478 TB_{\text{exp}} = 0.478\text{ T}

NEXT STEPS
Final Takeaways from Your Teacher
  • Practice isolating variables symbolically before substituting any numerical values.

  • Use dimensional analysis as a quick sanity check to ensure your units cancel to Teslas.

OverviewACEpath Teacher's Diagnosis

03 The student mistakenly uses Δm in the slope calculation or needlessly divides F_B by g believing the given forces were apparent masses that still require conversion.

Sample Student Work

Reviewed by ACEpath Teacher
Step-by-Step Review
Walk Through It with Your Teacher
Partially correct
  1. Step 1

    slope=0.191−0.0484.00−1.00=0.0477 N/A\text{slope} = \frac{0.191 - 0.048}{4.00 - 1.00} = 0.0477\text{ N/A}

  2. Step 2

    FB=slopeg=0.04779.80=0.00487 N/AF_B = \frac{\text{slope}}{g} = \frac{0.0477}{9.80} = 0.00487\text{ N/A}

    Correct

    slope=LBexp\text{slope} = L B_{\text{exp}}

    The measured quantities in the table were already magnetic forces FBF_B in Newtons (N\text{N}), not apparent masses Δm\Delta m in kilograms. Since the force balance conversion FB=Δm⋅gF_B = \Delta m \cdot g had already been performed in the problem statement, dividing the slope by gg was unnecessary and incorrect.

  3. Step 3

    Bexp=slope/gL=0.004870.100=0.0487 TB_{\text{exp}} = \frac{\text{slope}/g}{L} = \frac{0.00487}{0.100} = 0.0487\text{ T}

    Correct

    Bexp=slopeL=0.0478 N/A0.100 m=0.478 TB_{\text{exp}} = \frac{\text{slope}}{L} = \frac{0.0478\text{ N/A}}{0.100\text{ m}} = 0.478\text{ T}

    Your algebraic step dividing by length LL was conceptually correct, but the final numerical value is off by a factor of g≈9.8g \approx 9.8 due to the unneeded division in Step 2.

WHAT YOU DID WELL
Compliments from Your Teacher

You correctly identified that the relationship between magnetic force and current is linear.

You calculated the slope of the force-current relationship accurately from the trial data.

You correctly recognized that the magnetic field strength is obtained by dividing the force-current slope by the active conductor length LL.

THE ERROR
Where Your ACEpath Teacher Spotted the Mistake
Unnecessary conversion using g

You divided by g=9.80 m/s2g = 9.80\text{ m/s}^2 even though the experimental values were already converted to force units of Newtons.

WHY IT HAPPENED
ACEpath Teacher's Diagnosis

You conflated the measured physical quantity (force in Newtons) with the instrument's raw reading (apparent mass change Δm\Delta m). Always verify the units of your variables before introducing conversion constants like gg.

REASONING PATH
Your ACEpath teacher’s suggested approach
Unit Inspection
  • If the dependent variable is already expressed in Newtons (N\text{N}), it is already a force.

  • Check the given units: if the data is in N\text{N}, do not multiply or divide by gg.

Theoretical Slope Matching
  • For a perpendicular wire, FB=ILB  ⟹  FBI=LBF_B = I L B \implies \frac{F_B}{I} = L B.

  • Directly equate the slope of FBF_B vs. II to LBL B, giving B=slopeLB = \frac{\text{slope}}{L}.

CORRECTED PATH
ACEpath Teacher's Demonstration
  1. From the theoretical relation FB=ILBF_B = I L B, the slope of FBF_B versus II directly equals LBexpL B_{\text{exp}}.

  2. Using the least-squares slope m=0.0478 N/Am = 0.0478\text{ N/A} (or your two-point slope 0.0477 N/A0.0477\text{ N/A}):

  3. Bexp=slopeL=0.0478 N/A0.100 m=0.478 TB_{\text{exp}} = \frac{\text{slope}}{L} = \frac{0.0478\text{ N/A}}{0.100\text{ m}} = 0.478\text{ T}

Final answer

Bexp=0.478 TB_{\text{exp}} = 0.478\text{ T}

NEXT STEPS
Final Takeaways from Your Teacher
  • Review the distinction between raw balance readings (mass change Δm\Delta m in grams/kilograms) and calculated magnetic forces (FBF_B in Newtons).

  • Practice dimensional analysis on experimental slopes to ensure your slope units match your theoretical coefficient units.

Lock it in

Similar question

01

A straight wire of length L=0.050 mL = 0.050\text{ m} is held perpendicular to a uniform magnetic field. A linear fit of magnetic force FBF_B versus current II yields a slope of 0.035 N/A0.035\text{ N/A}. Determine the magnetic field strength BB.

Answer

B=0.70 TB = 0.70\text{ T}. Since FB=(LB)IF_B = (L B) I, the slope is m=LBm = L B. Thus, B=mL=0.035 N/A0.050 m=0.70 TB = \frac{m}{L} = \frac{0.035\text{ N/A}}{0.050\text{ m}} = 0.70\text{ T}.

02

In a current balance experiment, the current is held constant at I=2.50 AI = 2.50\text{ A} while the length LL of the wire segment inside a uniform perpendicular magnetic field is varied. A plot of FBF_B versus LL gives a slope of 1.15 N/m1.15\text{ N/m}. What is the magnetic field strength BB?

Answer

B=0.460 TB = 0.460\text{ T}. Here LL is the independent variable, so FB=(IB)LF_B = (I B) L. The slope is m=IBm = I B, giving B=mI=1.15 N/m2.50 A=0.460 TB = \frac{m}{I} = \frac{1.15\text{ N/m}}{2.50\text{ A}} = 0.460\text{ T}.

03

A conducting rod of length L=0.080 mL = 0.080\text{ m} is oriented at an angle of θ=30.0∘\theta = 30.0^\circ relative to a uniform magnetic field B⃗\vec{B}. When current II is varied, the linear regression slope of FBF_B vs. II is measured to be 0.024 N/A0.024\text{ N/A}. Find the magnetic field strength BB.

Answer

B=0.60 TB = 0.60\text{ T}. The general force equation is FB=(LBsin⁡θ)IF_B = (L B \sin\theta) I. The slope is m=LBsin⁡30.0∘=0.080⋅B⋅0.50=0.040Bm = L B \sin 30.0^\circ = 0.080 \cdot B \cdot 0.50 = 0.040 B. Therefore, B=0.024 N/A0.040 m=0.60 TB = \frac{0.024\text{ N/A}}{0.040\text{ m}} = 0.60\text{ T}.

Loading workspace…