Resources
A hollow spherical aluminum shell with outer radius and uniform wall thickness has an aluminum density of . The interior of the shell is evacuated (zero internal mass). The shell is placed in fresh water of density . Determine the critical maximum wall thickness such that the sphere remains neutrally buoyant (completely submerged without sinking to the bottom). (Assume ).
Answer and steps
Final answer
Steps
Condition for Neutral Buoyancy
An object is neutrally buoyant when it remains suspended at equilibrium in a fluid without rising or sinking. In this state, the net vertical force is zero, meaning the upward buoyant force equals the downward gravitational force (weight of the shell):
Formulating the Forces via Archimedes' Principle
- Buoyant Force ():
According to Archimedes' principle, the buoyant force equals the weight of the fluid displaced by the object. Because the sphere is fully submerged, the displaced fluid volume is the total external volume of the sphere, : - Gravitational Force ():
The interior cavity of the shell is evacuated, contributing zero mass. Therefore, the entire mass of the sphere resides in the spherical aluminum wall between inner radius and outer radius :
Deriving the Inner Radius and Wall Thickness
Equating and :
Cancel the common factor on both sides:
Divide by and isolate :
Taking the cube root of both sides gives the inner radius:
The critical wall thickness is the difference between the outer and inner radii:
Calculation
Substitute the given numerical values:
Calculate the density ratio and factor:
Now compute :
Pitfall to Avoid
- Thin-shell approximation error: Do not approximate the volume of the shell as . That approximation is only valid when (typically ). Here, the thickness is roughly of the radius, so using the thin-wall formula leads to significant error. Always use the exact difference of concentric spherical volumes, .
Typical errors
01 The student misuses the thin-wall surface area approximation V_Al ≈ 4*π*R_o²*t for a shell whose thickness is not negligible, underestimating the required thickness.
Sample Student Work
Reviewed by ACEpath TeacherStep-by-Step Review
Walk Through It with Your Teacher- Step 1
- Step 2Correct
You approximated the volume of the aluminum shell as the outer surface area multiplied by the thickness (). This linear approximation is only valid when . For a shell of significant thickness, you must use the exact difference of concentric spherical volumes, .
- Step 3Correct
Your algebraic rearrangement follows logically from your approximation in Step 2, but it inherits the thin-shell error.
- Step 4Correct
Your numerical evaluation is mathematically consistent with your derived formula, but the result underestimates the required thickness by over due to the initial approximation.
WHAT YOU DID WELL
Compliments from Your TeacherYou correctly identified that neutral buoyancy occurs when the buoyant force equals the weight of the object.
You accurately calculated the volume of displaced water using the total outer volume of the sphere.
You correctly substituted the fluid and material densities and executed clean algebraic cancellation.
THE ERROR
Where Your ACEpath Teacher Spotted the Mistakeno
WHY IT HAPPENED
ACEpath Teacher's DiagnosisYou assumed the spherical shell was thin enough to approximate its volume as . Because the thickness turns out to be around of the radius, the inner surface area is significantly smaller than the outer surface area, causing the linear approximation to substantially overestimate the volume of metal for a given thickness (and thus underestimate the thickness needed for a given mass).
REASONING PATH
Your ACEpath teacher’s suggested approach- Shell Volume Formula Selection
A spherical shell of outer radius and inner radius has exact volume . The thin-wall approximation is only appropriate when .
Always write the exact difference of spheres unless the problem explicitly states that the wall is ultrathin or provides an explicit condition .
CORRECTED PATH
ACEpath Teacher's DemonstrationEquate the buoyant force to the weight:
Cancel common factors :
Isolate :
Take the cube root to find :
Express thickness as
02 The student mistakenly writes the volume of the shell using the thickness cubed as (4/3)*π*t³ instead of the difference of the outer and inner sphere volumes.
Sample Student Work
Reviewed by ACEpath TeacherStep-by-Step Review
Walk Through It with Your Teacher- Step 1
- Step 2Correct
You substituted for the material volume of the shell. A spherical shell is the region between an outer sphere of radius and an inner sphere of radius , so its volume is , not the volume of a sphere of radius .
- Step 3Correct
Your algebraic isolation and numerical calculation were mathematically consistent with your equation from Step 2, but the final thickness is incorrect due to the volume formula error.
WHAT YOU DID WELL
Compliments from Your TeacherYou correctly identified the equilibrium condition for neutral buoyancy by equating the weight of displaced water to the total mass of the aluminum.
You carried out the algebraic rearrangement and cube root calculation cleanly.
THE ERROR
Where Your ACEpath Teacher Spotted the Mistakeno
WHY IT HAPPENED
ACEpath Teacher's DiagnosisYou treated the wall thickness as if it were the radius of an independent solid sphere of material rather than computing the volume of the spherical shell as the geometric difference between the outer sphere and the inner hollow cavity.
REASONING PATH
Your ACEpath teacher’s suggested approach- Volume of a Hollow Shell
The volume of a hollow spherical shell with outer radius and inner radius is , never .
Always represent the material volume as the total outer volume minus the inner void volume before relating the inner radius to the wall thickness via .
CORRECTED PATH
ACEpath Teacher's DemonstrationCancel common factors to get .
Rearrange to solve for the inner radius: .
Calculate the critical thickness using .
03 The student confuses the inner and outer radii in the volume difference formula by writing R_i³ - R_o³ or equating total volume to the hollow interior rather than the exterior.
Sample Student Work
Reviewed by ACEpath TeacherStep-by-Step Review
Walk Through It with Your Teacher- Step 1Correct
The volume of the spherical aluminum wall is the outer volume minus the inner cavity volume, which is . Because the outer radius is larger than the inner radius (), writing results in a negative volume.
- Step 2Correct
Your algebra followed from the reversed volume formula in Step 1, which yielded an impossible inner radius () that is strictly greater than the outer radius ().
- Step 3Correct
Because the previous step produced , you subtracted from to keep thickness positive, rather than evaluating with the correct radii.
WHAT YOU DID WELL
Compliments from Your TeacherYou correctly recognized that neutral buoyancy requires the upward buoyant force to balance the weight of the aluminum shell.
You correctly identified that the displaced fluid volume depends on the total exterior radius .
You correctly set up the force balance equation and eliminated common factors like and .
THE ERROR
Where Your ACEpath Teacher Spotted the MistakeWHY IT HAPPENED
ACEpath Teacher's DiagnosisYou subtracted the larger outer volume from the smaller inner volume () instead of computing outer minus inner (). A physical volume must always be positive, with .
REASONING PATH
Your ACEpath teacher’s suggested approach- Volume of a Hollow Shell
Always verify that your volume expression subtracts the smaller cavity from the larger outer boundary so that .
- Geometric Sanity Check
For any hollow shell, and .
Check calculated radii immediately: if , re-examine the algebraic signs in your volume balance.
CORRECTED PATH
ACEpath Teacher's DemonstrationSet up the exact volume of the aluminum shell: .
Equate buoyant force and weight: .
Cancel : .
Isolate : .
Substitute values: .
Calculate critical thickness: .
Lock it in
What is the exact volume of a hollow spherical shell with outer radius and inner radius ?
. Always take the difference between the outer and inner spherical volumes.
Similar question
A hollow spherical copper shell () has outer radius and an evacuated cavity. Find the inner radius such that the sphere is neutrally buoyant in water ().
Answer
. Set , so .
A hollow spherical plastic ball of outer radius has wall thickness and an evacuated interior. If the ball floats completely submerged in oil of density , determine the density of the plastic material .
Answer
. Inner radius is . Neutral buoyancy gives . Thus .
A hollow metal sphere of density floats half-submerged in a liquid of density . If the wall thickness equals , find the ratio .
Answer
. The displaced volume is . The metal volume is with . Flotation equilibrium gives . Therefore, .