Resources

A block of mass m=2.50 kgm = 2.50\text{ kg} is released from rest at the top of a curved, frictionless track at a vertical height h=3.60 mh = 3.60\text{ m} above a horizontal floor. At the bottom of the curve, the track transitions smoothly onto a rough horizontal surface characterized by a coefficient of kinetic friction μk=0.350\mu_k = 0.350. After sliding across the rough surface for a distance d=4.20 md = 4.20\text{ m}, the block impacts an uncompressed, ideal horizontal spring mounted rigidly to an end-wall. The spring has a force constant k=480 N/mk = 480\text{ N/m}. Taking the acceleration due to gravity as g=9.80 m/s2g = 9.80\text{ m/s}^2 and assuming friction continues to act beneath the block while the spring compresses, determine the maximum compression xmaxx_{\text{max}} of the spring in meters.

Answer and steps

Final answer

xmax=0.449 mx_{\text{max}} = 0.449\text{ m}

Steps

01

Identify the Physical Principles and Reference States

By the Work-Energy Theorem, the net work done by non-conservative forces equals the change in total mechanical energy of the block-spring-Earth system:

Wnc=ΔE=Ef−EiW_{\text{nc}} = \Delta E = E_f - E_i

  • Initial State (ii): The block is at rest at height h=3.60 mh = 3.60\text{ m} on the frictionless track, with zero kinetic energy and zero spring compression: Ei=mghE_i = mgh
  • Final State (ff): At maximum compression xmaxx_{\text{max}}, the block instantaneously comes to rest (v=0v = 0). Taking the horizontal floor as the reference level for gravitational potential energy (h=0h = 0), the mechanical energy consists solely of elastic potential energy stored in the spring: Ef=12kxmax2E_f = \frac{1}{2} k x_{\text{max}}^2

02

Formulate the Work Done by Non-Conservative Forces

The only non-conservative force acting on the system is kinetic friction along the horizontal rough surface.

  • The normal force on the horizontal surface is: N=mgN = mg
  • The magnitude of the kinetic friction force is: fk=μkN=μkmgf_k = \mu_k N = \mu_k mg
  • The friction force acts over the total sliding distance s=d+xmaxs = d + x_{\text{max}}. Because friction opposes the direction of motion at all times, the work done by friction is negative: Wnc=−fk(d+xmax)=−μkmg(d+xmax)W_{\text{nc}} = -f_k (d + x_{\text{max}}) = -\mu_k mg (d + x_{\text{max}})

Common Pitfall: A frequent mistake is accounting for friction only over the distance dd before the block strikes the spring. However, friction continues to act beneath the block as the spring is compressed by an additional distance xmaxx_{\text{max}}.


03

Set Up the Energy Conservation Equation

Substitute EiE_i, EfE_f, and WncW_{\text{nc}} into the work-energy relation:

Ef−Ei=WncE_f - E_i = W_{\text{nc}}

12kxmax2−mgh=−μkmg(d+xmax)\frac{1}{2} k x_{\text{max}}^2 - mgh = -\mu_k mg (d + x_{\text{max}})

Rearranging into standard quadratic form Axmax2+Bxmax+C=0A x_{\text{max}}^2 + B x_{\text{max}} + C = 0:

12kxmax2+μkmgxmax+(μkmgd−mgh)=0\frac{1}{2} k x_{\text{max}}^2 + \mu_k mg x_{\text{max}} + (\mu_k mg d - mgh) = 0


04

Substitute Numerical Values and Solve for xmaxx_{\text{max}}

Calculate each coefficient using the given values:

  • m=2.50 kgm = 2.50\text{ kg}
  • g=9.80 m/s2  ⟹  mg=(2.50)(9.80)=24.5 Ng = 9.80\text{ m/s}^2 \implies mg = (2.50)(9.80) = 24.5\text{ N}
  • A=12k=12(480)=240 N/mA = \frac{1}{2} k = \frac{1}{2}(480) = 240\text{ N/m}
  • B=μkmg=(0.350)(24.5)=8.575 NB = \mu_k mg = (0.350)(24.5) = 8.575\text{ N}
  • μkmgd=(8.575)(4.20)=36.015 J\mu_k mg d = (8.575)(4.20) = 36.015\text{ J}
  • mgh=(24.5)(3.60)=88.2 Jmgh = (24.5)(3.60) = 88.2\text{ J}
  • C=μkmgd−mgh=36.015−88.2=−52.185 JC = \mu_k mg d - mgh = 36.015 - 88.2 = -52.185\text{ J}

The quadratic equation is:

240xmax2+8.575xmax−52.185=0240 x_{\text{max}}^2 + 8.575 x_{\text{max}} - 52.185 = 0

Apply the quadratic formula, retaining the positive root since compression is a positive physical distance:

xmax=−B+B2−4AC2Ax_{\text{max}} = \frac{-B + \sqrt{B^2 - 4AC}}{2A}

xmax=−8.575+(8.575)2−4(240)(−52.185)2(240)x_{\text{max}} = \frac{-8.575 + \sqrt{(8.575)^2 - 4(240)(-52.185)}}{2(240)}

Evaluate the discriminant:

B2−4AC=73.530625+50097.6=50171.130625B^2 - 4AC = 73.530625 + 50097.6 = 50171.130625

B2−4AC≈223.989 N\sqrt{B^2 - 4AC} \approx 223.989\text{ N}

Substitute back to find xmaxx_{\text{max}}:

xmax=−8.575+223.989480=215.414480≈0.44878 mx_{\text{max}} = \frac{-8.575 + 223.989}{480} = \frac{215.414}{480} \approx 0.44878\text{ m}

Rounding to three significant figures gives:

xmax=0.449 mx_{\text{max}} = 0.449\text{ m}

Typical errors

OverviewACEpath Teacher's Diagnosis

01 The student ignores the work done by friction while the spring is compressing, accounting for friction only over the distance d.

Sample Student Work

Reviewed by ACEpath Teacher
Step-by-Step Review
Walk Through It with Your Teacher
Incorrect
  1. Step 1

    m∗g∗h=μk∗m∗g∗d+(1/2)∗k∗xmax2m * g * h = \mu_k * m * g * d + (1/2) * k * x_{\text{max}}^2

    Correct

    mgh=μkmg(d+xmax)+12kxmax2mgh = \mu_k mg (d + x_{\text{max}}) + \frac{1}{2} k x_{\text{max}}^2

    You accounted for friction only along the initial distance dd. Because the rough horizontal surface extends under the spring, friction continues to oppose the block's motion over the additional compression distance xmaxx_{\text{max}}, doing total work of −μkmg(d+xmax)-\mu_k mg(d + x_{\text{max}}).

  2. Step 2

    2.50∗9.80∗3.60=88.2 J  ⟹  Wf=0.350∗2.50∗9.80∗4.20=36.015 J2.50 * 9.80 * 3.60 = 88.2\text{ J} \implies W_f = 0.350 * 2.50 * 9.80 * 4.20 = 36.015\text{ J}

  3. Step 3

    88.2=36.015+(1/2)∗480∗xmax2  ⟹  52.185=240∗xmax2  ⟹  xmax2=0.217488.2 = 36.015 + (1/2)*480*x_{\text{max}}^2 \implies 52.185 = 240 * x_{\text{max}}^2 \implies x_{\text{max}}^2 = 0.2174

    Correct

    12(480)xmax2+(0.350)(24.5)xmax+(36.015−88.2)=0  ⟹  240xmax2+8.575xmax−52.185=0\frac{1}{2}(480) x_{\text{max}}^2 + (0.350)(24.5) x_{\text{max}} + (36.015 - 88.2) = 0 \implies 240 x_{\text{max}}^2 + 8.575 x_{\text{max}} - 52.185 = 0

    Because the linear friction term μkmgxmax\mu_k mg x_{\text{max}} was omitted in the initial energy balance, you solved a pure square relation instead of a full quadratic equation.

  4. Step 4

    xmax=0.466 mx_{\text{max}} = 0.466\text{ m}

    Correct

    xmax=0.449 mx_{\text{max}} = 0.449\text{ m}

    This result follows directly from the incomplete energy balance in your first step.

WHAT YOU DID WELL
Compliments from Your Teacher

You correctly identified that the system's mechanical energy is converted into thermal energy via friction and elastic potential energy in the spring.

You calculated the gravitational potential energy at the release height accurately.

You correctly determined the magnitude of the friction force acting on the horizontal floor.

THE ERROR
Where Your ACEpath Teacher Spotted the Mistake
Omission of Friction During Spring Compression

You treated friction as stopping once the block reached the spring, rather than continuing to act across the compression distance.

WHY IT HAPPENED
ACEpath Teacher's Diagnosis

Failing to define the total displacement over which the non-conservative force acts when a contact interaction overlaps with spring compression, leading to an incomplete work-energy balance.

REASONING PATH
Your ACEpath teacher’s suggested approach
Full Path of Non-Conservative Forces
  • Wnc=−fk⋅stotalW_{\text{nc}} = -f_k \cdot s_{\text{total}}, where stotals_{\text{total}} includes all distance traveled on the rough surface up to the instant the block stops.

  • Always write down the full stopping position relative to the start of the rough patch before writing the energy equation: stotal=d+xs_{\text{total}} = d + x.

Quadratic vs. Pure Square
  • When friction acts along with a linear spring, the work-energy relation must contain both a linear term (fkxf_k x) and a quadratic term (12kx2\frac{1}{2} k x^2).

  • Check whether your resulting equation contains both xx and x2x^2; if only x2x^2 appears, verify whether non-conservative forces act during compression.

CORRECTED PATH
ACEpath Teacher's Demonstration
  1. Write the complete energy balance: mgh=μkmg(d+xmax)+12kxmax2mgh = \mu_k mg(d + x_{\text{max}}) + \frac{1}{2} k x_{\text{max}}^2.

  2. Rearrange into standard quadratic form: 240xmax2+8.575xmax−52.185=0240 x_{\text{max}}^2 + 8.575 x_{\text{max}} - 52.185 = 0.

  3. Apply the quadratic formula: xmax=−8.575+8.5752−4(240)(−52.185)2(240)=−8.575+223.989480x_{\text{max}} = \frac{-8.575 + \sqrt{8.575^2 - 4(240)(-52.185)}}{2(240)} = \frac{-8.575 + 223.989}{480}.

Final answer

xmax=0.449 mx_{\text{max}} = 0.449\text{ m}

NEXT STEPS
Final Takeaways from Your Teacher
  • Re-solve the quadratic equation 240xmax2+8.575xmax−52.185=0240 x_{\text{max}}^2 + 8.575 x_{\text{max}} - 52.185 = 0 using the quadratic formula to obtain 0.449 m0.449\text{ m}.

  • Practice sketching a position timeline of the block showing both contact with the rough floor and contact with the spring to ensure no overlapping force intervals are overlooked.

OverviewACEpath Teacher's Diagnosis

02 The student forgets the factor of 1/2 in the formula for elastic potential energy of the spring.

Sample Student Work

Reviewed by ACEpath Teacher
Step-by-Step Review
Walk Through It with Your Teacher
Incorrect
  1. Step 1

    mgh=μkmg(d+xmax)+kxmax2  ⟹  480xmax2+8.575xmax−52.185=0mgh = \mu_k mg(d + x_{\text{max}}) + k x_{\text{max}}^2 \implies 480 x_{\text{max}}^2 + 8.575 x_{\text{max}} - 52.185 = 0

    Correct

    mgh=μkmg(d+xmax)+12kxmax2  ⟹  240xmax2+8.575xmax−52.185=0mgh = \mu_k mg(d + x_{\text{max}}) + \frac{1}{2} k x_{\text{max}}^2 \implies 240 x_{\text{max}}^2 + 8.575 x_{\text{max}} - 52.185 = 0

    The elastic potential energy stored in an ideal spring compressed by a distance xx is Us=12kx2U_s = \frac{1}{2} k x^2, not kx2k x^2. Because you missed the factor of 12\frac{1}{2}, the quadratic coefficient AA became 480480 instead of 12(480)=240\frac{1}{2}(480) = 240.

  2. Step 2

    xmax=−8.575+8.5752−4(480)(−52.185)2(480)=−8.575+316.65960x_{\text{max}} = \frac{-8.575 + \sqrt{8.575^2 - 4(480)(-52.185)}}{2(480)} = \frac{-8.575 + 316.65}{960}

    Correct

    xmax=−8.575+8.5752−4(240)(−52.185)2(240)=−8.575+223.989480x_{\text{max}} = \frac{-8.575 + \sqrt{8.575^2 - 4(240)(-52.185)}}{2(240)} = \frac{-8.575 + 223.989}{480}

    Your algebraic execution of the quadratic formula is mathematically sound for your coefficients, but your calculation is affected by the incorrect leading coefficient A=480A = 480.

  3. Step 3

    xmax=0.321 mx_{\text{max}} = 0.321\text{ m}

    Correct

    xmax≈0.449 mx_{\text{max}} \approx 0.449\text{ m}

    Your final numerical answer is smaller than the true value because doubling the spring energy term overestimates the spring's restoring resistance.

WHAT YOU DID WELL
Compliments from Your Teacher

You correctly identified that initial gravitational potential energy is converted into thermal energy from friction and elastic potential energy in the spring.

You correctly recognized that friction continues to act along the surface while the spring compresses, writing the total friction distance as d+xmaxd + x_{\text{max}}.

You correctly evaluated the numerical values of mghmgh, μkmg\mu_k mg, and solved your resulting quadratic equation accurately.

THE ERROR
Where Your ACEpath Teacher Spotted the Mistake
Missing Elastic Potential Energy Factor of 1/2

You wrote the elastic potential energy of the spring as kxmax2k x_{\text{max}}^2 instead of 12kxmax2\frac{1}{2} k x_{\text{max}}^2.

WHY IT HAPPENED
ACEpath Teacher's Diagnosis

You conflated the spring force magnitude from Hooke's Law (Fs=kxF_s = kx) with the work required to compress it (W=∫kx dx=12kx2W = \int kx\,dx = \frac{1}{2}kx^2). Because the spring force varies linearly from 00 to kxkx, the average force is 12kx\frac{1}{2}kx, which introduces the necessary factor of 12\frac{1}{2} into the energy expression.

REASONING PATH
Your ACEpath teacher’s suggested approach
Spring Force vs. Spring Energy
  • Hooke's Law gives force: Fs=kxF_s = kx. Work-energy gives potential energy: Us=12kx2U_s = \frac{1}{2} k x^2.

  • Always verify that potential energy terms have units of energy (N⋅m=J\text{N}\cdot\text{m} = \text{J}) and include the integration factor of 12\frac{1}{2} for linear restoring forces.

Quadratic Setup Verification
  • In an equation of the form 12kx2+bx+c=0\frac{1}{2}kx^2 + bx + c = 0, the quadratic coefficient is A=12kA = \frac{1}{2}k.

  • Check that the coefficient of x2x^2 is half the spring constant, not the full spring constant kk.

CORRECTED PATH
ACEpath Teacher's Demonstration
  1. Substitute Us=12kxmax2U_s = \frac{1}{2} k x_{\text{max}}^2 into the energy conservation equation: mgh=μkmg(d+xmax)+12kxmax2mgh = \mu_k mg(d + x_{\text{max}}) + \frac{1}{2} k x_{\text{max}}^2.

  2. Insert the numerical values: 88.2=8.575(4.20+xmax)+240xmax288.2 = 8.575(4.20 + x_{\text{max}}) + 240 x_{\text{max}}^2.

  3. Expand and rearrange into standard quadratic form: 240xmax2+8.575xmax−52.185=0240 x_{\text{max}}^2 + 8.575 x_{\text{max}} - 52.185 = 0.

  4. Apply the quadratic formula with A=240A = 240, B=8.575B = 8.575, and C=−52.185C = -52.185: xmax=−8.575+8.5752−4(240)(−52.185)2(240)=−8.575+223.989480≈0.44878 mx_{\text{max}} = \frac{-8.575 + \sqrt{8.575^2 - 4(240)(-52.185)}}{2(240)} = \frac{-8.575 + 223.989}{480} \approx 0.44878\text{ m}.

Final answer

xmax=0.449 mx_{\text{max}} = 0.449\text{ m}

NEXT STEPS
Final Takeaways from Your Teacher
  • Review the derivation of spring potential energy via work integration: W=∫0xkx′ dx′=12kx2W = \int_0^x kx'\,dx' = \frac{1}{2}kx^2.

  • Practice flagging formulas with quadratic dependencies (Ek=12mv2E_k = \frac{1}{2}mv^2, Us=12kx2U_s = \frac{1}{2}kx^2) to make sure the 12\frac{1}{2} factor is never omitted.

  • Work through the targeted flashcards and practice problems below to master energy conservation setups with springs and non-conservative forces.

OverviewACEpath Teacher's Diagnosis

03 The student equates the spring force directly to the kinetic friction force instead of using energy conservation to find the maximum compression.

Sample Student Work

Reviewed by ACEpath Teacher
Step-by-Step Review
Walk Through It with Your Teacher
Incorrect
  1. Step 1

    k⋅xmax=μk⋅m⋅g  ⟹  480⋅xmax=0.350⋅2.50⋅9.80  ⟹  480⋅xmax=8.575k \cdot x_{\text{max}} = \mu_k \cdot m \cdot g \implies 480 \cdot x_{\text{max}} = 0.350 \cdot 2.50 \cdot 9.80 \implies 480 \cdot x_{\text{max}} = 8.575

    Correct

    12kxmax2−mgh=−μkmg(d+xmax)  ⟹  240xmax2+8.575xmax−52.185=0\frac{1}{2} k x_{\text{max}}^2 - m g h = -\mu_k m g (d + x_{\text{max}}) \implies 240 x_{\text{max}}^2 + 8.575 x_{\text{max}} - 52.185 = 0

    You treated maximum compression as a point of static force equilibrium where Fspring=fkF_{\text{spring}} = f_k. Maximum compression occurs when the block instantaneously comes to rest (v=0v = 0), not when net force is zero. You need to apply the work-energy theorem, equating the change in mechanical energy to the work done by friction: ΔE=Wnc\Delta E = W_{\text{nc}}.

  2. Step 2

    xmax=8.575/480  ⟹  xmax=0.0179 mx_{\text{max}} = 8.575 / 480 \implies x_{\text{max}} = 0.0179\text{ m}

    Correct

    xmax=−8.575+8.5752−4(240)(−52.185)2(240)≈0.449 mx_{\text{max}} = \frac{-8.575 + \sqrt{8.575^2 - 4(240)(-52.185)}}{2(240)} \approx 0.449\text{ m}

    Your arithmetic solving for xmaxx_{\text{max}} followed logically from your equation in Step 1, but the resulting value is incorrect because the governing equation omitted energy conservation.

WHAT YOU DID WELL
Compliments from Your Teacher

You correctly identified the formula for kinetic friction on a flat surface, fk=μkmgf_k = \mu_k m g.

You substituted the correct numerical values for mass, gravity, and the coefficient of friction.

THE ERROR
Where Your ACEpath Teacher Spotted the Mistake
Force Equilibrium Instead of Work-Energy

You set the spring restoring force equal to the friction force at maximum compression.

WHY IT HAPPENED
ACEpath Teacher's Diagnosis

You conflated the condition for zero acceleration (force equilibrium, where speed is actually near maximum) with the condition for turning points / maximum displacement (where instantaneous speed v=0v = 0).

REASONING PATH
Your ACEpath teacher’s suggested approach
Turning Point vs. Equilibrium
  • At maximum spring compression or stretch, velocity is momentarily zero (v=0v = 0), but acceleration is generally non-zero (Fnet≠0F_{\text{net}} \neq 0).

  • Use the work-energy relation Ef−Ei=WncE_f - E_i = W_{\text{nc}} whenever analyzing extreme displacements or stopping distances.

Total Friction Distance
  • If friction continues during compression, the total distance over which friction does work is the approach distance plus the compression distance: s=d+xs = d + x.

  • Include the compression distance xmaxx_{\text{max}} in the work done by friction: Wf=−fk(d+xmax)W_f = -f_k (d + x_{\text{max}}).

CORRECTED PATH
ACEpath Teacher's Demonstration
  1. Set up the work-energy relation between release from rest at height hh and instantaneous rest at maximum compression: 12kxmax2−mgh=−μkmg(d+xmax)\frac{1}{2} k x_{\text{max}}^2 - m g h = -\mu_k m g (d + x_{\text{max}}).

  2. Substitute the given parameters: mg=2.50×9.80=24.5 Nm g = 2.50 \times 9.80 = 24.5\text{ N}, mgh=24.5×3.60=88.2 Jm g h = 24.5 \times 3.60 = 88.2\text{ J}, and fk=0.350×24.5=8.575 Nf_k = 0.350 \times 24.5 = 8.575\text{ N}.

  3. Formulate the quadratic equation: 240xmax2+8.575xmax−52.185=0240 x_{\text{max}}^2 + 8.575 x_{\text{max}} - 52.185 = 0.

  4. Solve for the positive physical root: xmax=−8.575+8.5752−4(240)(−52.185)480=−8.575+223.989480≈0.449 mx_{\text{max}} = \frac{-8.575 + \sqrt{8.575^2 - 4(240)(-52.185)}}{480} = \frac{-8.575 + 223.989}{480} \approx 0.449\text{ m}.

Final answer

xmax=0.449 mx_{\text{max}} = 0.449\text{ m}

NEXT STEPS
Final Takeaways from Your Teacher
  • Review the distinction between maximum velocity (where net force is zero) and maximum displacement (where velocity is zero).

  • Practice formulating work-energy balances where non-conservative forces act along variable or composite paths.

Lock it in

Similar question

01

A 1.50 kg1.50\text{ kg} block slides on a rough horizontal surface with μk=0.200\mu_k = 0.200. It has an initial speed of 3.00 m/s3.00\text{ m/s} when it immediately encounters an uncompressed horizontal spring with k=150 N/mk = 150\text{ N/m}. The rough surface extends beneath the spring. Find the maximum compression xmaxx_{\text{max}} of the spring. (Use g=9.80 m/s2g = 9.80\text{ m/s}^2.)

Answer

xmax=0.281 mx_{\text{max}} = 0.281\text{ m}. Initial kinetic energy is Ek=12(1.50)(3.00)2=6.75 JE_k = \frac{1}{2}(1.50)(3.00)^2 = 6.75\text{ J}. Friction force is fk=μkmg=(0.200)(1.50)(9.80)=2.94 Nf_k = \mu_k mg = (0.200)(1.50)(9.80) = 2.94\text{ N}. The energy balance is 6.75=2.94xmax+75xmax26.75 = 2.94 x_{\text{max}} + 75 x_{\text{max}}^2, or 75xmax2+2.94xmax−6.75=075 x_{\text{max}}^2 + 2.94 x_{\text{max}} - 6.75 = 0. Solving via the quadratic formula gives xmax≈0.281 mx_{\text{max}} \approx 0.281\text{ m}.

02

A 3.00 kg3.00\text{ kg} crate is pushed down an incline and reaches the bottom with a speed of 5.00 m/s5.00\text{ m/s}. It then travels across a flat rough floor (μk=0.400\mu_k = 0.400) for a distance d=2.00 md = 2.00\text{ m} before hitting a horizontal spring (k=300 N/mk = 300\text{ N/m}). If friction continues to act under the crate while the spring is compressed, determine the maximum compression xmaxx_{\text{max}}. (Use g=9.80 m/s2g = 9.80\text{ m/s}^2.)

Answer

xmax=0.274 mx_{\text{max}} = 0.274\text{ m}. Initial kinetic energy is 12(3.00)(5.00)2=37.5 J\frac{1}{2}(3.00)(5.00)^2 = 37.5\text{ J}. Normal force is N=mg=(3.00)(9.80)=29.4 NN = mg = (3.00)(9.80) = 29.4\text{ N}, so fk=(0.400)(29.4)=11.76 Nf_k = (0.400)(29.4) = 11.76\text{ N}. Over distance d=2.00 md = 2.00\text{ m}, friction dissipates 11.76×2.00=23.52 J11.76 \times 2.00 = 23.52\text{ J}. The energy equation is 37.5=23.52+11.76xmax+150xmax237.5 = 23.52 + 11.76 x_{\text{max}} + 150 x_{\text{max}}^2, which simplifies to 150xmax2+11.76xmax−13.98=0150 x_{\text{max}}^2 + 11.76 x_{\text{max}} - 13.98 = 0. Solving yields xmax≈0.274 mx_{\text{max}} \approx 0.274\text{ m}.

03

A block of mass mm is released from rest at height hh on a frictionless ramp that transitions into a horizontal rough surface with kinetic friction coefficient μk\mu_k. After traveling a distance dd on the flat surface, it compresses a spring of force constant kk by a maximum amount xx. Derive an algebraic expression for the release height hh in terms of mm, gg, μk\mu_k, dd, kk, and xx.

Answer

h=μk(d+x)+kx22mgh = \mu_k (d + x) + \frac{k x^2}{2mg}. By conservation of energy, the initial potential energy mghmgh must equal the total energy dissipated by friction plus the elastic energy stored in the spring: mgh=fk(d+x)+12kx2=μkmg(d+x)+12kx2mgh = f_k (d + x) + \frac{1}{2} k x^2 = \mu_k mg(d + x) + \frac{1}{2} k x^2. Dividing the entire equation by mgmg yields h=μk(d+x)+kx22mgh = \mu_k(d + x) + \frac{kx^2}{2mg}.

Loading workspace…