Resources
An industrial turbine shaft has an initial angular velocity of (revolutions per minute). It decelerates with a constant angular acceleration of magnitude (degrees per second squared). Convert all quantities to standard SI units (radians and seconds) and calculate: (a) the time required for the shaft to come to a complete stop, and (b) the total angular displacement in radians, as well as the total number of complete revolutions executed during this braking period.
Answer and steps
Final answer
(a) ; (b) ,
Steps
Convert given quantities to standard SI units
In rotational kinematics, the standard SI unit for angular displacement is the radian (), for angular velocity is radians per second (), and for angular acceleration is radians per second squared ().
- Initial angular velocity (): One revolution is equal to , and one minute is equal to :
- Angular acceleration (): One full circle has , which means . Because the shaft is decelerating (braking), the angular acceleration opposes the direction of initial rotation:
Calculate the time required to come to rest ()
Use the first rotational kinematic equation relating angular velocity, angular acceleration, and time:
Setting the final angular velocity to at :
Calculate the total angular displacement () and number of revolutions ()
-
Angular displacement in radians (): Using the average angular velocity formula for constant acceleration:
Evaluating numerically to three significant figures:
- Total complete revolutions (): Since each complete revolution corresponds to :
(Common Pitfall: Do not mix unit systems during kinematic calculations—such as directly dividing rpm by degrees per second squared without first converting both into consistent units of radians and seconds, or revolutions and seconds.)
Typical errors
01 The student forgets to convert the initial angular velocity from revolutions per minute to radians per second by dividing by 60, resulting in an angular velocity that is 60 times too large.
Sample Student Work
Reviewed by ACEpath TeacherStep-by-Step Review
Walk Through It with Your Teacher- Step 1Correct
You correctly multiplied by to change revolutions to radians, but you missed dividing by to convert minutes into seconds.
- Step 2
- Step 3Correct
Your algebraic setup and choice of kinematic equation were completely correct, but the calculation inherited the inflated value from Step 1.
- Step 4Correct
You chose the ideal work-energy rotational kinematic equation, but substituting the incorrect caused the angular displacement to be times too large.
- Step 5Correct
You correctly related total revolutions to angular displacement by dividing by , carrying through the earlier conversion error.
WHAT YOU DID WELL
Compliments from Your TeacherYou selected the correct rotational kinematic equations for both stopping time and angular displacement.
You converted degrees per second squared to radians per second squared with complete accuracy.
You properly converted the final displacement from radians into complete revolutions.
THE ERROR
Where Your ACEpath Teacher Spotted the MistakeYou remembered that one revolution equals , but overlooked that rpm means revolutions per minute, forgetting to divide by .
WHY IT HAPPENED
ACEpath Teacher's DiagnosisTreating purely as an angular measure rather than a compound rate (angle per unit time), leading to a missing factor of .
REASONING PATH
Your ACEpath teacher’s suggested approach- Compound Unit Decomposition
Always expand composite unit abbreviations before multiplying: .
Write out the units explicitly as a dimensional analysis fraction before inserting numbers into kinematic formulas.
CORRECTED PATH
ACEpath Teacher's DemonstrationConvert initial angular velocity using both revolution and time factors: .
Substitute into .
Compute displacement: .
Calculate total revolutions: .
(a) ; (b) ,
02 The student forgets to convert the angular acceleration from degrees per second squared to radians per second squared, leaving α in degrees per second squared while using ω in radians per second.
Sample Student Work
Reviewed by ACEpath TeacherStep-by-Step Review
Walk Through It with Your Teacher- Step 1
- Step 2Correct
You replaced the degree symbol with radians directly without multiplying by the conversion factor . Since , .
- Step 3Correct
You chose the correct kinematic relation , but substituting your unconverted value of led to an incorrect stopping time.
- Step 4Correct
Your algebraic manipulation of is completely sound, but the result is affected by the incorrect value of .
- Step 5Correct
You correctly divided your angular displacement by to find revolutions, but the numerical answer inherits the earlier unit conversion error.
WHAT YOU DID WELL
Compliments from Your TeacherYou correctly converted the initial angular velocity from to .
You correctly selected and manipulated the standard rotational kinematic formulas for constant deceleration.
You correctly related angular displacement in radians to complete revolutions by dividing by .
THE ERROR
Where Your ACEpath Teacher Spotted the MistakeYou treated the magnitude as if it were already in instead of converting from degrees to radians.
WHY IT HAPPENED
ACEpath Teacher's DiagnosisConflating degree and radian angular measures or assuming angular acceleration values given with a degree symbol can directly interface with angular velocities measured in radians per second.
REASONING PATH
Your ACEpath teacher’s suggested approach- Angular Unit Consistency
In rotational kinematic formulas such as and , all angular terms (, , ) must share the same angle unit (standard SI unit is the radian).
Before substituting into formulas, explicitly convert degrees to radians using .
CORRECTED PATH
ACEpath Teacher's DemonstrationConvert : .
Calculate stopping time: .
Calculate angular displacement: .
Calculate complete revolutions: .
(a) ; (b) ,
03 The student omits the factor of 2 in the denominator of the kinematic equation Δθ = ω₀² / (2α), taking Δθ = ω₀² / α.
Sample Student Work
Reviewed by ACEpath TeacherStep-by-Step Review
Walk Through It with Your Teacher- Step 1
- Step 2
- Step 3Correct
The kinematic relation is . Setting gives . You forgot the factor of in the denominator, which doubled your result.
- Step 4Correct
Your conversion method from radians to revolutions by dividing by was correct, but the numerical answer inherits the factor-of-two error from the previous step.
WHAT YOU DID WELL
Compliments from Your TeacherYou correctly converted both the initial angular velocity and angular acceleration into consistent SI units of and .
You set up and solved the linear kinematic relation for angular velocity to find the correct stopping time .
You used the correct relationship between angular displacement and complete revolutions ().
THE ERROR
Where Your ACEpath Teacher Spotted the MistakeYou wrote instead of .
WHY IT HAPPENED
ACEpath Teacher's DiagnosisYou confused the time-independent kinematic relation with an un-integrated rate expression, dropping the that arises from integrating (or from multiplying average velocity by time).
REASONING PATH
Your ACEpath teacher’s suggested approach- Torricelli Analogy Check
Just as contains a factor of , the rotational counterpart is .
Always verify that any 'squared velocity equals acceleration times displacement' formula includes the coefficient on the acceleration term.
- Average Velocity Cross-Check
For constant acceleration, displacement is average velocity times time: .
Since you already computed , check your displacement via to catch formula slips immediately.
CORRECTED PATH
ACEpath Teacher's DemonstrationApply with :
Convert radians to revolutions:
(a) ; (b) (),
Lock it in
How do you convert an angular velocity given in (revolutions per minute) to the SI unit ?
Multiply by (or ). The factor converts revolutions to radians, and dividing by converts minutes to seconds.
Similar question
A grinding wheel spins initially at and experiences a constant deceleration of until it stops. Calculate the time required for the wheel to come to rest.
Answer
. Key steps: Convert . Use .
A centrifuge decelerates uniformly from to a complete stop in . Find: (a) its angular deceleration in , and (b) the total number of revolutions completed while coming to rest.
Answer
(a) ; (b) . Key steps: . . Total revolutions .
An electric drill rotating at is switched off and decelerates at a constant rate of . Calculate: (a) the time required to stop, and (b) the total angular displacement in radians.
Answer
(a) ; (b) . Key steps: ; . Stopping time . Displacement .