Resources

A circular conducting loop of radius r0=0.15 mr_0 = 0.15\text{ m} and fixed electrical resistance R=0.60 ΩR = 0.60\ \Omega is situated in a uniform perpendicular magnetic field whose magnitude increases with time according to the asymptotic function B(t)=Bmax(1−e−t/τ)B(t) = B_{\text{max}}\left(1 - e^{-t/\tau}\right), where Bmax=2.50 TB_{\text{max}} = 2.50\text{ T} and the characteristic time constant is τ=0.40 s\tau = 0.40\text{ s}. Find the exact expression for the induced current I(t)I(t) as a function of time, evaluate the initial current I(0+)I(0^+) at t=0t = 0, and determine the asymptotic limiting value of the induced current I∞I_\infty as t→∞t \to \infty.

Answer and steps

Final answer

I(t)=0.736e−2.50t AI(t) = 0.736 e^{-2.50t}\text{ A}, I(0+)=0.736 AI(0^+) = 0.736\text{ A}, I∞=0 AI_\infty = 0\text{ A}

Steps

01

Determine the Area and the Magnetic Flux

The area AA enclosed by the circular conducting loop of radius r0=0.15 mr_0 = 0.15\text{ m} is: A=πr02=π(0.15 m)2≈0.07069 m2A = \pi r_0^2 = \pi (0.15\text{ m})^2 \approx 0.07069\text{ m}^2

Because the magnetic field is perpendicular to the plane of the loop, the angle between the normal to the surface and the magnetic field is 0∘0^\circ (cos⁡0∘=1\cos 0^\circ = 1). The magnetic flux ΦB(t)\Phi_B(t) linking the loop at time tt is: ΦB(t)=B(t)⋅A=ABmax(1−e−t/τ)\Phi_B(t) = B(t) \cdot A = A B_{\text{max}}\left(1 - e^{-t/\tau}\right)


02

Apply Faraday's Law to Find the Induced EMF

According to Faraday's law of electromagnetic induction, the magnitude of the induced electromotive force (EMF) E(t)\mathcal{E}(t) equals the time rate of change of magnetic flux through the loop: E(t)=∣−dΦBdt∣=AdBdt\mathcal{E}(t) = \left| -\frac{d\Phi_B}{dt} \right| = A \frac{dB}{dt}

Differentiating B(t)B(t) with respect to time: dBdt=ddt[Bmax(1−e−t/τ)]=Bmaxτe−t/τ\frac{dB}{dt} = \frac{d}{dt}\left[B_{\text{max}}\left(1 - e^{-t/\tau}\right)\right] = \frac{B_{\text{max}}}{\tau} e^{-t/\tau}

Substituting the expression for dB/dtdB/dt into the EMF formula gives: E(t)=ABmaxτe−t/τ\mathcal{E}(t) = \frac{A B_{\text{max}}}{\tau} e^{-t/\tau}


03

Derive the Induced Current Expression I(t)I(t)

Using Ohm's law, the induced current in the loop with resistance R=0.60 ΩR = 0.60\ \Omega is: I(t)=E(t)R=πr02BmaxτRe−t/τI(t) = \frac{\mathcal{E}(t)}{R} = \frac{\pi r_0^2 B_{\text{max}}}{\tau R} e^{-t/\tau}

Substitute the numerical values:

  • τ=0.40 s  ⟹  1τ=2.50 s−1\tau = 0.40\text{ s} \implies \frac{1}{\tau} = 2.50\text{ s}^{-1}
  • Pre-exponential amplitude: I0=π(0.15)2⋅2.500.40⋅0.60≈0.176710.24≈0.736 AI_0 = \frac{\pi (0.15)^2 \cdot 2.50}{0.40 \cdot 0.60} \approx \frac{0.17671}{0.24} \approx 0.736\text{ A}

Thus, the function for the induced current as time evolves is: I(t)=0.736e−2.50t AI(t) = 0.736 e^{-2.50t}\text{ A}


04

Evaluate the Initial and Asymptotic Currents

  1. Initial current (t=0t = 0): I(0+)=0.736e0 A=0.736 AI(0^+) = 0.736 e^{0}\text{ A} = 0.736\text{ A}
  2. Asymptotic current (t→∞t \to \infty): As t→∞t \to \infty, the exponential term decays to zero (lim⁡t→∞e−2.50t=0\lim_{t \to \infty} e^{-2.50t} = 0): I∞=lim⁡t→∞I(t)=0 AI_\infty = \lim_{t \to \infty} I(t) = 0\text{ A}

Key Pitfall: Notice that although the magnetic field B(t)B(t) asymptotically reaches its maximum value of 2.50 T2.50\text{ T} as t→∞t \to \infty, the induced current approaches 0 A0\text{ A}. Electromagnetic induction depends on the rate of change of magnetic flux (dB/dtdB/dt), not the magnitude of the field itself. When the field levels off, dB/dt→0dB/dt \to 0, causing the induced EMF and current to vanish.

Typical errors

OverviewACEpath Teacher's Diagnosis

01 The student confuses the magnetic field magnitude with its time derivative when applying Faraday's law, using ε = B·A instead of A·(dB/dt).

Sample Student Work

Reviewed by ACEpath Teacher
Step-by-Step Review
Walk Through It with Your Teacher
Incorrect
  1. Step 1

    A=πr02=π(0.15)2=0.0225π m2A = \pi r_0^2 = \pi (0.15)^2 = 0.0225\pi\text{ m}^2

  2. Step 2

    E(t)=B(t)⋅A=2.50(1−e−t/0.40)⋅0.0225π  ⟹  I(t)=E(t)R≈0.295(1−e−2.5t) A\mathcal{E}(t) = B(t) \cdot A = 2.50(1 - e^{-t/0.40}) \cdot 0.0225\pi \implies I(t) = \frac{\mathcal{E}(t)}{R} \approx 0.295(1 - e^{-2.5t})\text{ A}

    Correct

    E(t)=AdBdt=ABmaxτe−t/τ  ⟹  I(t)=E(t)R=0.736e−2.50t A\mathcal{E}(t) = A\frac{dB}{dt} = A\frac{B_{\text{max}}}{\tau}e^{-t/\tau} \implies I(t) = \frac{\mathcal{E}(t)}{R} = 0.736e^{-2.50t}\text{ A}

    You set E(t)=B(t)⋅A\mathcal{E}(t) = B(t) \cdot A, which is the magnetic flux ΦB(t)\Phi_B(t), not the induced electromotive force. According to Faraday's law, induced EMF is proportional to the time rate of change of magnetic flux, E(t)=A∣dBdt∣=ABmaxτe−t/τ\mathcal{E}(t) = A\left|\frac{dB}{dt}\right| = \frac{AB_{\text{max}}}{\tau}e^{-t/\tau}.

  3. Step 3

    I(0+)=0.295(1−e0)=0 A  ⟹  I∞=0.295 AI(0^+) = 0.295(1 - e^0) = 0\text{ A} \implies I_\infty = 0.295\text{ A}

    Correct

    I(0+)=0.736e0=0.736 A  ⟹  I∞=lim⁡t→∞0.736e−2.50t=0 AI(0^+) = 0.736e^0 = 0.736\text{ A} \implies I_\infty = \lim_{t \to \infty} 0.736e^{-2.50t} = 0\text{ A}

    Your evaluations at t=0t = 0 and t→∞t \to \infty followed your derived formula correctly, but the values are inverted because the formula for I(t)I(t) missed the time derivative.

WHAT YOU DID WELL
Compliments from Your Teacher

You calculated the geometric area of the loop correctly.

You applied Ohm's law I=ERI = \frac{\mathcal{E}}{R} appropriately to your expression for electromotive force.

You evaluated limits at t=0t = 0 and t→∞t \to \infty accurately for the algebraic expression you had written.

THE ERROR
Where Your ACEpath Teacher Spotted the Mistake
Flux vs. EMF confusion in Faraday's law

You treated the magnetic field magnitude B(t)B(t) as if it were directly generating the EMF, writing E=B⋅A\mathcal{E} = B \cdot A instead of differentiating with respect to time.

WHY IT HAPPENED
ACEpath Teacher's Diagnosis

Confusing magnetic flux ΦB=BA\Phi_B = B A with induced electromotive force E=−dΦBdt\mathcal{E} = -\frac{d\Phi_B}{dt}. Electromagnetic induction requires a changing flux; an EMF only exists while the field is actively changing.

REASONING PATH
Your ACEpath teacher’s suggested approach
Flux vs. Induced EMF
  • Magnetic flux is ΦB=∫B⃗⋅dA⃗\Phi_B = \int \vec{B} \cdot d\vec{A}. Induced EMF is its time derivative: E=−dΦBdt\mathcal{E} = -\frac{d\Phi_B}{dt}.

  • Always differentiate ΦB(t)\Phi_B(t) with respect to time before calculating induced EMF or induced current.

Rate of Change of an Asymptotic Field
  • For B(t)=Bmax(1−e−t/τ)B(t) = B_{\text{max}}(1 - e^{-t/\tau}), the derivative is dBdt=Bmaxτe−t/τ\frac{dB}{dt} = \frac{B_{\text{max}}}{\tau}e^{-t/\tau}.

  • Remember that ddt(1−e−t/τ)=+1τe−t/τ\frac{d}{dt}(1 - e^{-t/\tau}) = +\frac{1}{\tau}e^{-t/\tau}, which is maximum at t=0t=0 and decays to 00 as t→∞t \to \infty.

CORRECTED PATH
ACEpath Teacher's Demonstration
  1. Find the rate of change of the magnetic field: dBdt=ddt[2.50(1−e−t/0.40)]=2.500.40e−2.50t=6.25e−2.50t T/s\frac{dB}{dt} = \frac{d}{dt}\left[2.50(1 - e^{-t/0.40})\right] = \frac{2.50}{0.40}e^{-2.50t} = 6.25e^{-2.50t}\text{ T/s}.

  2. Apply Faraday's law for a stationary perpendicular loop: E(t)=AdBdt=(0.0225π)(6.25e−2.50t)=0.140625πe−2.50t≈0.4418e−2.50t V\mathcal{E}(t) = A\frac{dB}{dt} = (0.0225\pi)(6.25e^{-2.50t}) = 0.140625\pi e^{-2.50t}\approx 0.4418e^{-2.50t}\text{ V}.

  3. Compute the current using Ohm's law: I(t)=E(t)R=0.140625πe−2.50t0.60≈0.736e−2.50t AI(t) = \frac{\mathcal{E}(t)}{R} = \frac{0.140625\pi e^{-2.50t}}{0.60} \approx 0.736e^{-2.50t}\text{ A}.

  4. Evaluate at t=0t = 0: I(0+)=0.736e0=0.736 AI(0^+) = 0.736e^{0} = 0.736\text{ A}.

  5. Evaluate as t→∞t \to \infty: since lim⁡t→∞e−2.50t=0\lim_{t \to \infty} e^{-2.50t} = 0, I∞=0 AI_\infty = 0\text{ A}.

Final answer

I(t)=0.736e−2.50t AI(t) = 0.736e^{-2.50t}\text{ A}, I(0+)=0.736 AI(0^+) = 0.736\text{ A}, I∞=0 AI_\infty = 0\text{ A}

NEXT STEPS
Final Takeaways from Your Teacher
  • Practice taking the time derivative of flux dΦBdt\frac{d\Phi_B}{dt} explicitly before writing down E\mathcal{E}.

  • Perform a physical reality check on asymptotic limits: when a magnetic field becomes constant at t→∞t \to \infty, flux stops changing, so the induced current must drop to zero.

OverviewACEpath Teacher's Diagnosis

02 The student differentiates the exponential function without applying the chain rule, omitting the factor of 1/τ in dB/dt.

Sample Student Work

Reviewed by ACEpath Teacher
Step-by-Step Review
Walk Through It with Your Teacher
Partially correct
  1. Step 1

    A=π⋅r02=π⋅(0.15)2=0.0225π m2A = \pi \cdot r_0^2 = \pi \cdot (0.15)^2 = 0.0225\pi\text{ m}^2

  2. Step 2

    dBdt=Bmax⋅e−t/τ\frac{dB}{dt} = B_{\text{max}} \cdot e^{-t/\tau}

    Correct

    dBdt=ddt[Bmax(1−e−t/τ)]=Bmaxτe−t/τ\frac{dB}{dt} = \frac{d}{dt}\left[B_{\text{max}}\left(1 - e^{-t/\tau}\right)\right] = \frac{B_{\text{max}}}{\tau} e^{-t/\tau}

    When differentiating B(t)=Bmax(1−e−t/τ)B(t) = B_{\text{max}}(1 - e^{-t/\tau}) with respect to time, applying the chain rule to −e−t/τ-e^{-t/\tau} gives −(−1/τ)e−t/τ=(1/τ)e−t/τ-(-1/\tau)e^{-t/\tau} = (1/\tau)e^{-t/\tau}. You forgot to multiply by the inner derivative 1/τ1/\tau.

  3. Step 3

    E(t)=A⋅(dBdt)=0.0225π⋅2.50⋅e−t/0.40=0.05625π⋅e−2.5t  ⟹  I(t)=E(t)R=0.05625π0.60e−2.5t=3π32e−2.5t≈0.295e−2.5t A\mathcal{E}(t) = A \cdot \left(\frac{dB}{dt}\right) = 0.0225\pi \cdot 2.50 \cdot e^{-t/0.40} = 0.05625\pi \cdot e^{-2.5t} \implies I(t) = \frac{\mathcal{E}(t)}{R} = \frac{0.05625\pi}{0.60} e^{-2.5t} = \frac{3\pi}{32} e^{-2.5t} \approx 0.295 e^{-2.5t}\text{ A}

    Correct

    I(t)=E(t)R=ABmaxτRe−t/τ=0.0225π⋅2.500.40⋅0.60e−2.50t≈0.736e−2.50t AI(t) = \frac{\mathcal{E}(t)}{R} = \frac{A B_{\text{max}}}{\tau R} e^{-t/\tau} = \frac{0.0225\pi \cdot 2.50}{0.40 \cdot 0.60} e^{-2.50t} \approx 0.736 e^{-2.50t}\text{ A}

    Your application of Faraday's law and Ohm's law is conceptually correct, but this step is affected by the missing factor of 1/τ=2.50 s−11/\tau = 2.50\text{ s}^{-1} from your derivative.

  4. Step 4

    I(0+)=3π32⋅e0≈0.295 AI(0^+) = \frac{3\pi}{32} \cdot e^0 \approx 0.295\text{ A}

    Correct

    I(0+)=0.736e0 A=0.736 AI(0^+) = 0.736 e^0\text{ A} = 0.736\text{ A}

    You correctly substituted t=0t = 0 into your derived expression, but the numerical value inherits the missing factor of 1/τ1/\tau.

  5. Step 5

    As t→∞, e−2.5t→0  ⟹  I∞=0 A\text{As } t \to \infty,\ e^{-2.5t} \to 0 \implies I_\infty = 0\text{ A}

WHAT YOU DID WELL
Compliments from Your Teacher

You correctly computed the area of the circular loop.

You properly set up Faraday's law and Ohm's law to relate the rate of change of magnetic flux to induced current.

You correctly identified that the induced current vanishes asymptotically as t→∞t \to \infty.

THE ERROR
Where Your ACEpath Teacher Spotted the Mistake
Omission of chain rule factor in exponential derivative

You missed the inner derivative factor 1/τ1/\tau when differentiating e−t/τe^{-t/\tau}.

WHY IT HAPPENED
ACEpath Teacher's Diagnosis

A calculus slip when differentiating composite exponential functions of the form f(t)=1−e−ktf(t) = 1 - e^{-kt}, where the constant coefficient k=1/τk = 1/\tau from the chain rule was omitted.

REASONING PATH
Your ACEpath teacher’s suggested approach
Chain Rule for Exponentials
  • ddt[eu(t)]=eu(t)⋅u′(t)\frac{d}{dt}\left[e^{u(t)}\right] = e^{u(t)} \cdot u'(t), so ddt[−e−t/τ]=1τe−t/τ\frac{d}{dt}\left[-e^{-t/\tau}\right] = \frac{1}{\tau} e^{-t/\tau}.

  • Always verify the units of your derivative: since BB has units of T\text{T}, dB/dtdB/dt must have units of T/s\text{T}/\text{s}, which requires dividing by time τ\tau.

CORRECTED PATH
ACEpath Teacher's Demonstration
  1. dBdt=ddt[Bmax(1−e−t/τ)]=Bmaxτe−t/τ\frac{dB}{dt} = \frac{d}{dt}\left[B_{\text{max}}\left(1 - e^{-t/\tau}\right)\right] = \frac{B_{\text{max}}}{\tau} e^{-t/\tau}

  2. E(t)=AdBdt=πr02Bmaxτe−t/τ\mathcal{E}(t) = A \frac{dB}{dt} = \frac{\pi r_0^2 B_{\text{max}}}{\tau} e^{-t/\tau}

  3. I(t)=E(t)R=π(0.15)2⋅2.500.40⋅0.60e−t/0.40≈0.736e−2.50t AI(t) = \frac{\mathcal{E}(t)}{R} = \frac{\pi (0.15)^2 \cdot 2.50}{0.40 \cdot 0.60} e^{-t/0.40} \approx 0.736 e^{-2.50t}\text{ A}

  4. I(0+)=0.736e0 A=0.736 AI(0^+) = 0.736 e^0\text{ A} = 0.736\text{ A}

Final answer

I(t)=0.736e−2.50t AI(t) = 0.736 e^{-2.50t}\text{ A}, I(0+)=0.736 AI(0^+) = 0.736\text{ A}, I∞=0 AI_\infty = 0\text{ A}

NEXT STEPS
Final Takeaways from Your Teacher
  • Double-check derivatives of exponential functions involving parameters like t/τt/\tau by explicitly writing out the chain rule.

  • Use dimensional analysis as a quick sanity check: verify that dB/dtdB/dt has units of T/s\text{T}/\text{s} before substituting into Faraday's law.

OverviewACEpath Teacher's Diagnosis

03 The student incorrectly uses the loop circumference 2·π·r₀ instead of the enclosed area π·r₀² when computing magnetic flux.

Sample Student Work

Reviewed by ACEpath Teacher
Step-by-Step Review
Walk Through It with Your Teacher
Incorrect
  1. Step 1

    A=2⋅π⋅r0=2⋅π⋅0.15=0.30⋅π m2A = 2\cdot\pi\cdot r_0 = 2\cdot\pi\cdot 0.15 = 0.30\cdot\pi\text{ m}^2

    Correct

    A=πr02=π(0.15 m)2=0.0225π m2≈0.0707 m2A = \pi r_0^2 = \pi (0.15\text{ m})^2 = 0.0225\pi\text{ m}^2 \approx 0.0707\text{ m}^2

    You substituted the circumference formula 2πr02\pi r_0 instead of the circular area formula A=πr02A = \pi r_0^2.

  2. Step 2

    dBdt=(Bmaxτ)e−t/τ=(2.500.40)e−t/0.40=6.25e−2.5t\frac{dB}{dt} = \left(\frac{B_{\text{max}}}{\tau}\right) e^{-t/\tau} = \left(\frac{2.50}{0.40}\right) e^{-t/0.40} = 6.25 e^{-2.5t}

  3. Step 3

    E(t)=A⋅(dBdt)=0.30⋅π⋅6.25⋅e−2.5t=1.875⋅π⋅e−2.5t\mathcal{E}(t) = A\cdot\left(\frac{dB}{dt}\right) = 0.30\cdot\pi\cdot 6.25\cdot e^{-2.5t} = 1.875\cdot\pi\cdot e^{-2.5t}

    Correct

    E(t)=AdBdt=(0.0225π)(6.25e−2.50t)≈0.4418e−2.50t V\mathcal{E}(t) = A\frac{dB}{dt} = (0.0225\pi)(6.25 e^{-2.50t}) \approx 0.4418 e^{-2.50t}\text{ V}

    Your application of Faraday's law E=A(dB/dt)\mathcal{E} = A(dB/dt) was conceptually correct, but the numerical value carried over the erroneous area from Step 1.

  4. Step 4

    I(t)=E(t)R=(1.875⋅π0.60)e−2.5t=(25⋅π8)e−2.5t≈9.817e−2.5t AI(t) = \frac{\mathcal{E}(t)}{R} = \left(\frac{1.875\cdot\pi}{0.60}\right) e^{-2.5t} = \left(\frac{25\cdot\pi}{8}\right) e^{-2.5t} \approx 9.817 e^{-2.5t}\text{ A}

    Correct

    I(t)=E(t)R=0.0225π⋅6.250.60e−2.50t≈0.736e−2.50t AI(t) = \frac{\mathcal{E}(t)}{R} = \frac{0.0225\pi \cdot 6.25}{0.60} e^{-2.50t} \approx 0.736 e^{-2.50t}\text{ A}

    You correctly related current to induced EMF through Ohm's law, but the amplitude propagated the incorrect area.

  5. Step 5

    I(0+)=25⋅π8⋅e0≈9.817 A  ⟹  As t→∞, e−2.5t→0  ⟹  I∞=0 AI(0^+) = \frac{25\cdot\pi}{8}\cdot e^0 \approx 9.817\text{ A} \implies \text{As } t \to \infty,\, e^{-2.5t} \to 0 \implies I_\infty = 0\text{ A}

    Correct

    I(0+)=0.736 A,I∞=0 AI(0^+) = 0.736\text{ A},\quad I_\infty = 0\text{ A}

    Your limiting logic for both t=0t = 0 and t→∞t \to \infty is sound, but I(0+)I(0^+) inherits the earlier numerical factor.

WHAT YOU DID WELL
Compliments from Your Teacher

You correctly differentiated the asymptotic magnetic field function with respect to time.

You properly applied Faraday's law and Ohm's law to link magnetic flux change to induced current.

You evaluated the asymptotic behavior as t→∞t \to \infty accurately.

THE ERROR
Where Your ACEpath Teacher Spotted the Mistake
Geometry Formula Confusion (Circumference vs. Area)

You wrote 2πr02\pi r_0 instead of πr02\pi r_0^2 when finding the enclosed surface area of the loop.

WHY IT HAPPENED
ACEpath Teacher's Diagnosis

Confusing linear loop perimeter/circumference (2πr2\pi r) with the 2D planar enclosed surface area (πr2\pi r^2) needed for magnetic flux ΦB=∫B⃗⋅dA⃗\Phi_B = \int \vec{B} \cdot d\vec{A}.

REASONING PATH
Your ACEpath teacher’s suggested approach
Flux Requires Surface Area
  • Magnetic flux measures field lines passing through a two-dimensional surface: ΦB=B⋅A\Phi_B = B \cdot A.

  • Always verify that you are computing the cross-sectional area enclosed by the perimeter (A=πr2A = \pi r^2 for a circle), never the boundary length (2πr2\pi r).

Dimensional Unit Check
  • Area must have dimensions of length2\text{length}^2 ( m2\,\text{m}^2).

  • Notice that 2πr02\pi r_0 has units of meters (m\text{m}), whereas an area requires squaring the linear dimension.

CORRECTED PATH
ACEpath Teacher's Demonstration
  1. Recalculate the circular loop area: A=πr02=π(0.15 m)2=0.0225π m2≈0.07069 m2A = \pi r_0^2 = \pi (0.15\text{ m})^2 = 0.0225\pi\text{ m}^2 \approx 0.07069\text{ m}^2.

  2. Calculate the induced EMF: E(t)=AdBdt=(0.0225π m2)(6.25e−2.50t T/s)=0.140625πe−2.50t V\mathcal{E}(t) = A \frac{dB}{dt} = (0.0225\pi\text{ m}^2)(6.25 e^{-2.50t}\text{ T/s}) = 0.140625\pi e^{-2.50t}\text{ V}.

  3. Apply Ohm's law to determine I(t)I(t): I(t)=E(t)R=0.140625π0.60e−2.50t A≈0.736e−2.50t AI(t) = \frac{\mathcal{E}(t)}{R} = \frac{0.140625\pi}{0.60} e^{-2.50t}\text{ A} \approx 0.736 e^{-2.50t}\text{ A}.

  4. Evaluate at t=0t = 0: I(0+)=0.736e0 A=0.736 AI(0^+) = 0.736 e^0\text{ A} = 0.736\text{ A}.

  5. Evaluate as t→∞t \to \infty: I∞=lim⁡t→∞0.736e−2.50t A=0 AI_\infty = \lim_{t \to \infty} 0.736 e^{-2.50t}\text{ A} = 0\text{ A}.

Final answer

I(t)=0.736e−2.50t AI(t) = 0.736 e^{-2.50t}\text{ A}, I(0+)=0.736 AI(0^+) = 0.736\text{ A}, I∞=0 AI_\infty = 0\text{ A}

NEXT STEPS
Final Takeaways from Your Teacher
  • Double-check dimensional units whenever computing geometric terms like area or volume.

  • Practice distinguishing the physical perimeter (relevant for wire length and resistance) from the enclosed area (relevant for flux).

Lock it in

Similar question

01

A loop of area A=0.05 m2A = 0.05\text{ m}^2 and resistance R=2.0 ΩR = 2.0\ \Omega lies perpendicular to a magnetic field B(t)=4.0t2 TB(t) = 4.0t^2\text{ T}. Find the magnitude of the induced current I(t)I(t) at t=3.0 st = 3.0\text{ s}.

Answer

I(3.0 s)=0.60 AI(3.0\text{ s}) = 0.60\text{ A}. Key steps: dBdt=8.0t T/s  ⟹  E(t)=AdBdt=0.05(8.0t)=0.40t V\frac{dB}{dt} = 8.0t\text{ T/s} \implies \mathcal{E}(t) = A\frac{dB}{dt} = 0.05(8.0t) = 0.40t\text{ V}. At t=3.0 st = 3.0\text{ s}, E=1.2 V\mathcal{E} = 1.2\text{ V}. Then I=ER=1.2 V2.0 Ω=0.60 AI = \frac{\mathcal{E}}{R} = \frac{1.2\text{ V}}{2.0\ \Omega} = 0.60\text{ A}.

02

A square coil with side length s=0.20 ms = 0.20\text{ m} and resistance R=0.50 ΩR = 0.50\ \Omega is perpendicular to a field decaying as B(t)=B0e−αtB(t) = B_0 e^{-\alpha t}, where B0=1.5 TB_0 = 1.5\text{ T} and α=10 s−1\alpha = 10\text{ s}^{-1}. Determine the induced current I(t)I(t) and its value at t=0t = 0.

Answer

I(t)=1.2e−10t AI(t) = 1.2e^{-10t}\text{ A}, with I(0)=1.2 AI(0) = 1.2\text{ A}. Key steps: Area A=s2=0.04 m2A = s^2 = 0.04\text{ m}^2. Rate of change ∣dBdt∣=αB0e−αt=15e−10t T/s\left|\frac{dB}{dt}\right| = \alpha B_0 e^{-\alpha t} = 15e^{-10t}\text{ T/s}. Induced EMF E(t)=A∣dBdt∣=0.04(15e−10t)=0.60e−10t V\mathcal{E}(t) = A\left|\frac{dB}{dt}\right| = 0.04(15e^{-10t}) = 0.60e^{-10t}\text{ V}. Current I(t)=ER=0.600.50e−10t=1.2e−10t AI(t) = \frac{\mathcal{E}}{R} = \frac{0.60}{0.50}e^{-10t} = 1.2e^{-10t}\text{ A}.

03

A circular loop of radius r=0.10 mr = 0.10\text{ m} and resistance R=0.25 ΩR = 0.25\ \Omega sits in a perpendicular magnetic field B(t)=Bmaxsin⁡(ωt)B(t) = B_{\text{max}}\sin(\omega t), where Bmax=0.80 TB_{\text{max}} = 0.80\text{ T} and ω=50 rad/s\omega = 50\text{ rad/s}. Find the maximum induced current ImaxI_{\text{max}} in the loop.

Answer

Imax≈5.03 AI_{\text{max}} \approx 5.03\text{ A}. Key steps: Area A=πr2=0.01π m2A = \pi r^2 = 0.01\pi\text{ m}^2. Rate of change dBdt=Bmaxωcos⁡(ωt)=40cos⁡(50t) T/s\frac{dB}{dt} = B_{\text{max}}\omega \cos(\omega t) = 40\cos(50t)\text{ T/s}. Peak EMF Emax=A(Bmaxω)=0.01π×40=0.40π V≈1.257 V\mathcal{E}_{\text{max}} = A(B_{\text{max}}\omega) = 0.01\pi \times 40 = 0.40\pi\text{ V} \approx 1.257\text{ V}. Peak current Imax=EmaxR=0.40π0.25=1.6π A≈5.03 AI_{\text{max}} = \frac{\mathcal{E}_{\text{max}}}{R} = \frac{0.40\pi}{0.25} = 1.6\pi\text{ A} \approx 5.03\text{ A}.

Loading workspace…