Resources
In a physics laboratory experiment to calibrate a spring-mass damper mechanism, a glider of mass is attached to a horizontal spring on an air track. An optical photogate array records positions and velocities. With the air blower turned off, the glider encounters dry kinetic friction along the track. The spring is extended by from equilibrium and released from rest. A digital force sensor records the effective spring constant as . After the glider oscillates through one full half-cycle and swings past equilibrium to its first turning point on the opposite side, the photogate measures a maximum compression of . (a) Using the Work-Energy Theorem, determine the coefficient of kinetic friction between the glider and the unpowered air track. (b) Calculate the total thermal energy dissipated during this first half-cycle. (Use .)
Answer and steps
Final answer
(a) ; (b)
Steps
Identify the Initial and Final States
We consider the motion of the glider from the moment of release to its first turning point on the opposite side:
- Initial state (): The glider is released from rest at maximum extension . Its initial kinetic energy is , and its initial elastic potential energy is:
- Final state (first turning point): The glider momentarily comes to rest at maximum compression . Its kinetic energy is again , and its final elastic potential energy is:
Calculate the Dissipated Thermal Energy (Part b)
According to the Law of Conservation of Energy, the non-conservative work done by friction converts mechanical energy into thermal energy :
Since kinetic energy is zero at both endpoints:
Substitute the given numerical values:
Determine the Coefficient of Kinetic Friction (Part a)
By the Work-Energy Theorem, the work done by the non-conservative friction force equals the change in mechanical energy:
The magnitude of the normal force on the level track is:
Thus, the constant kinetic friction force opposing the motion has magnitude:
Over the path of travel with effective distance , the work done by friction is:
Equating this to :
Solving for the coefficient of kinetic friction :
Evaluating using the experimental parameters gives:
Typical errors
01 The student uses the difference between the amplitudes rather than their sum as the distance traversed by the glider over the half-cycle, leading to an incorrect work expression.
Sample Student Work
Reviewed by ACEpath TeacherStep-by-Step Review
Walk Through It with Your Teacher- Step 1Correct
The glider starts at maximum extension , passes through the equilibrium position , and continues to maximum compression on the opposite side. The total distance traveled across this half-cycle is the sum of the magnitudes, , not their difference.
- Step 2
- Step 3Correct
Your formulation of the work done by friction is conceptually sound, but substituting the incorrect path length artificially inflated the friction coefficient.
WHAT YOU DID WELL
Compliments from Your TeacherYou correctly used the elastic potential energy formula at both turning points where kinetic energy vanishes.
You correctly related the change in mechanical energy to the work done by kinetic friction.
THE ERROR
Where Your ACEpath Teacher Spotted the MistakeYou computed the difference between turning-point amplitudes rather than summing the two segments of travel across equilibrium.
WHY IT HAPPENED
ACEpath Teacher's DiagnosisConfusing the net change in amplitude with the total physical path length traveled during a half-oscillation from one side of equilibrium to the other.
REASONING PATH
Your ACEpath teacher’s suggested approach- Path Length Across Equilibrium
Friction acts continuously along the actual distance traveled: , where for motion crossing equilibrium.
Sketch the glider's track, mark , , and , and sum the physical distances of both legs.
- Physical Reality Check for $\mu_k$
Kinetic friction coefficients for metal gliders on smooth tracks typically lie between and .
If your calculated exceeds for standard laboratory surfaces, recheck whether your path length was underestimated.
CORRECTED PATH
ACEpath Teacher's DemonstrationFind the total distance traveled during the half-cycle: .
Apply the Work-Energy Theorem: .
Solve for the coefficient of kinetic friction: (or depending on experimental calibration).
(a) (or ); (b)
02 The student omits the factor of 1/2 in the elastic potential energy formula, leading to doubled mechanical energy values and a doubled friction coefficient.
Sample Student Work
Reviewed by ACEpath TeacherStep-by-Step Review
Walk Through It with Your Teacher- Step 1
- Step 2Correct
You omitted the factor of from the elastic potential energy formula , calculating instead.
- Step 3Correct
Your algebraic technique for isolating was correct, but the numerical result is approximately twice the true value because it used the unhalved .
- Step 4Correct
Your conceptual connection between thermal dissipation and mechanical energy loss was completely sound, but the final value remained doubled due to the missing factor.
WHAT YOU DID WELL
Compliments from Your TeacherYou correctly summed the maximum extension and compression to find the total distance traveled .
You correctly applied the work-energy relation equating non-conservative friction work to mechanical energy change, .
You correctly related dissipated thermal energy to the decrease in mechanical energy.
THE ERROR
Where Your ACEpath Teacher Spotted the MistakeWriting instead of when computing initial and final spring potential energies.
WHY IT HAPPENED
ACEpath Teacher's DiagnosisConfusing the elastic potential energy stored in a spring with force expressions or forgetting that integrating Hooke's Law over displacement yields .
REASONING PATH
Your ACEpath teacher’s suggested approach- Formula Verification
The elastic potential energy stored in an ideal spring stretched or compressed by displacement is .
Always verify that your quadratic energy expressions ( and ) include the prefactor before substituting numerical values.
CORRECTED PATH
ACEpath Teacher's DemonstrationSet :
(a) ; (b)
03 The student subtracts amplitudes directly before squaring when calculating the lost mechanical energy instead of squaring each amplitude separately.
Sample Student Work
Reviewed by ACEpath TeacherStep-by-Step Review
Walk Through It with Your Teacher- Step 1
- Step 2
- Step 3Correct
You subtracted the amplitudes before squaring: . The mechanical energy lost is the difference between the two potential energies, .
- Step 4Correct
Your algebra for equating work to mechanical energy change was logically consistent, but the numerical result was affected by the error in in Step 3.
- Step 5Correct
Your calculation for thermal dissipation carried over the same expression instead of evaluating .
WHAT YOU DID WELL
Compliments from Your TeacherYou correctly recognized that the glider travels a total distance equal to in a half-cycle.
You correctly expressed the work done by kinetic friction as .
You correctly equated the thermal energy generated to the magnitude of the mechanical energy loss.
THE ERROR
Where Your ACEpath Teacher Spotted the MistakeYou wrote instead of when calculating the lost mechanical energy.
WHY IT HAPPENED
ACEpath Teacher's DiagnosisConfusing the difference of squares with the square of a difference . In quadratic energy terms like , each state's coordinate must be squared before taking their difference.
REASONING PATH
Your ACEpath teacher’s suggested approach- Evaluate energy at states independently
Always compute and separately first, then subtract: .
- Verify non-linear property
Never factor out the exponent 2 across a subtraction sign.
CORRECTED PATH
ACEpath Teacher's DemonstrationCalculate the initial and final mechanical energies: .
Calculate .
Find the thermal energy dissipated: .
Equate dissipated energy to work against friction: .
(a) ; (b)
Lock it in
When an oscillating mass moves from through equilibrium to , what is the total distance traveled?
. Because friction always opposes instantaneous velocity, work depends on the cumulative path length, not coordinate difference.
Similar question
A glider on a horizontal spring with is released from rest at . It passes through equilibrium and comes to rest momentarily at . Calculate the work done by friction during this half-cycle.
Answer
.
For the glider in the previous question, determine the constant kinetic friction force and the coefficient of kinetic friction . (Use .)
Answer
Total distance is . Friction force is . The coefficient is .
A mass attached to a horizontal spring of stiffness oscillates on a surface with kinetic friction coefficient . If released from rest at extension , prove that the maximum compression at the end of the first half-cycle satisfies .
Answer
By energy conservation, . Factoring the left side gives . Dividing both sides by yields .