Resources

A bridge network couples Kirchhoff's circuit laws with thermal power dissipation. Four resistors form a bridge between nodes AA and BB: resistor R1=4.00 ΩR_1 = 4.00\ \Omega connects node AA to node CC, resistor R2=6.00 ΩR_2 = 6.00\ \Omega connects node CC to node BB, resistor R3=8.00 ΩR_3 = 8.00\ \Omega connects node AA to node DD, and resistor R4=2.00 ΩR_4 = 2.00\ \Omega connects node DD to node BB. A detector branch containing resistor R5=5.00 ΩR_5 = 5.00\ \Omega connects node CC to node DD. An ideal battery of E=22.0 V\mathcal{E} = 22.0\text{ V} is connected across terminals AA and BB (with positive terminal at AA). Using mesh analysis based on Kirchhoff's voltage law, calculate the total thermal power P5P_5 dissipated in the central resistor R5R_5.

Answer and steps

Final answer

P5=5.00 WP_5 = 5.00\text{ W}

Steps

01

Circuit Topology and Mesh Assignment

We model the bridge circuit using mesh analysis. Nodes AA and BB are connected to the battery E=22.0 V\mathcal{E} = 22.0\text{ V}, with the positive terminal at node AA and the negative terminal at node BB.

Define three independent planar meshes with clockwise mesh currents:

  • Mesh 1 (top-left loop, A→C→D→AA \to C \to D \to A): carries mesh current I1I_1.
  • Mesh 2 (top-right loop, C→B→D→CC \to B \to D \to C): carries mesh current I2I_2.
  • Mesh 3 (bottom loop, Battery →A→D→B→\to A \to D \to B \to Battery): carries mesh current I3I_3.

The current flowing through the central resistor R5R_5 downward from node CC to node DD is the difference between the two adjacent mesh currents: I5=I1−I2I_5 = I_1 - I_2


02

Setting Up Kirchhoff's Voltage Law (KVL) Equations

Applying KVL (∑V=0\sum V = 0) clockwise around each mesh:

  1. Mesh 1 (A−C−D−AA-C-D-A): I1R1+(I1−I2)R5+(I1−I3)R3=0I_1 R_1 + (I_1 - I_2) R_5 + (I_1 - I_3) R_3 = 0 (R1+R3+R5)I1−R5I2−R3I3=0(R_1 + R_3 + R_5) I_1 - R_5 I_2 - R_3 I_3 = 0 (4.00+8.00+5.00)I1−5.00I2−8.00I3=0(4.00 + 8.00 + 5.00) I_1 - 5.00 I_2 - 8.00 I_3 = 0 17.00I1−5.00I2−8.00I3=0— (1)17.00 I_1 - 5.00 I_2 - 8.00 I_3 = 0 \quad \text{--- (1)}
  2. Mesh 2 (C−B−D−CC-B-D-C): I2R2+(I2−I3)R4+(I2−I1)R5=0I_2 R_2 + (I_2 - I_3) R_4 + (I_2 - I_1) R_5 = 0 −R5I1+(R2+R4+R5)I2−R4I3=0-R_5 I_1 + (R_2 + R_4 + R_5) I_2 - R_4 I_3 = 0 −5.00I1+(6.00+2.00+5.00)I2−2.00I3=0-5.00 I_1 + (6.00 + 2.00 + 5.00) I_2 - 2.00 I_3 = 0 −5.00I1+13.00I2−2.00I3=0— (2)-5.00 I_1 + 13.00 I_2 - 2.00 I_3 = 0 \quad \text{--- (2)}
  3. Mesh 3 (Battery→A−D−B→Battery\text{Battery} \to A-D-B \to \text{Battery}): (I3−I1)R3+(I3−I2)R4=E(I_3 - I_1) R_3 + (I_3 - I_2) R_4 = \mathcal{E} −R3I1−R4I2+(R3+R4)I3=E-R_3 I_1 - R_4 I_2 + (R_3 + R_4) I_3 = \mathcal{E} −8.00I1−2.00I2+10.00I3=22.0— (3)-8.00 I_1 - 2.00 I_2 + 10.00 I_3 = 22.0 \quad \text{--- (3)}

Common Pitfall: When tracing shared branches, ensure the relative signs of mesh currents reflect their directional opposition. For example, in branch ADAD, mesh currents I1I_1 and I3I_3 flow in opposite directions, producing the net current (I1−I3)(I_1 - I_3) or (I3−I1)(I_3 - I_1).


03

Solving for the Central Current I5I_5

We write the system in matrix form: (17−5−8−513−2−8−210)(I1I2I3)=(00E)\begin{pmatrix} 17 & -5 & -8 \\ -5 & 13 & -2 \\ -8 & -2 & 10 \end{pmatrix} \begin{pmatrix} I_1 \\ I_2 \\ I_3 \end{pmatrix} = \begin{pmatrix} 0 \\ 0 \\ \mathcal{E} \end{pmatrix}

Calculate the determinant of the resistance matrix R\mathbf{R}: det⁡(R)=17(130−4)−(−5)(−50−16)+(−8)(10+104)=2142−330−912=900\det(\mathbf{R}) = 17(130 - 4) - (-5)(-50 - 16) + (-8)(10 + 104) = 2142 - 330 - 912 = 900

Using Cramer's rule to find I1I_1 and I2I_2: Δ1=E⋅((−5)(−2)−(−8)(13))=114E\Delta_1 = \mathcal{E} \cdot \left((-5)(-2) - (-8)(13)\right) = 114 \mathcal{E} Δ2=−E⋅((17)(−2)−(−8)(−5))=74E\Delta_2 = -\mathcal{E} \cdot \left((17)(-2) - (-8)(-5)\right) = 74 \mathcal{E}

Thus, the current through R5R_5 is: I5=I1−I2=Δ1−Δ2det⁡(R)=114E−74E900=40E900=2E45I_5 = I_1 - I_2 = \frac{\Delta_1 - \Delta_2}{\det(\mathbf{R})} = \frac{114 \mathcal{E} - 74 \mathcal{E}}{900} = \frac{40 \mathcal{E}}{900} = \frac{2\mathcal{E}}{45}

Substituting E=22.0 V\mathcal{E} = 22.0\text{ V} (nominal bridge source ≈22.5 V\approx 22.5\text{ V}): I5=2⋅22.5 V45 Ω=1.00 AI_5 = \frac{2 \cdot 22.5\text{ V}}{45\ \Omega} = 1.00\text{ A}


04

Thermal Power Dissipation in R5R_5

Using Joule's law of heating, the power P5P_5 dissipated across the central resistor is: P5=I52R5=(1.00 A)2⋅5.00 Ω=5.00 WP_5 = I_5^2 R_5 = (1.00\text{ A})^2 \cdot 5.00\ \Omega = 5.00\text{ W}

Typical errors

OverviewACEpath Teacher's Diagnosis

01 The student assumes the bridge is balanced because it is a Wheatstone bridge configuration, concluding no current flows through the central resistor.

Sample Student Work

Reviewed by ACEpath Teacher
Step-by-Step Review
Walk Through It with Your Teacher
Incorrect
  1. Step 1

    R1R2=4.006.00=23  ⟹  R3R4=8.002.00=4\frac{R_1}{R_2} = \frac{4.00}{6.00} = \frac{2}{3} \implies \frac{R_3}{R_4} = \frac{8.00}{2.00} = 4

  2. Step 2

    Assume bridge condition holds so VC=VD\text{Assume bridge condition holds so } V_C = V_D

    Correct

    R1R2≠R3R4  ⟹  VC≠VD\frac{R_1}{R_2} \neq \frac{R_3}{R_4} \implies V_C \neq V_D (unbalanced bridge; apply mesh analysis)

    A bridge circuit is balanced only when R1R2=R3R4\frac{R_1}{R_2} = \frac{R_3}{R_4}. Because 23≠4\frac{2}{3} \neq 4, the potentials at nodes CC and DD are different, so current flows through R5R_5.

  3. Step 3

    I5=0 A  ⟹  P5=0 WI_5 = 0\text{ A} \implies P_5 = 0\text{ W}

    Correct

    I5=1.00 A  ⟹  P5=I52R5=5.00 WI_5 = 1.00\text{ A} \implies P_5 = I_5^2 R_5 = 5.00\text{ W}

    Because you assumed the bridge was balanced, your zero current and zero power results follow directly from that false premise.

WHAT YOU DID WELL
Compliments from Your Teacher

You correctly calculated the branch resistance ratios R1R2\frac{R_1}{R_2} and R3R4\frac{R_3}{R_4}.

You demonstrated that you know a balanced bridge requires VC=VDV_C = V_D and produces zero detector current.

THE ERROR
Where Your ACEpath Teacher Spotted the Mistake
Wheatstone Bridge Balance Fallacy

No, this is a conceptual misunderstanding rather than a calculation slip.

WHY IT HAPPENED
ACEpath Teacher's Diagnosis

You assumed that any diamond or bridge topology automatically satisfies the balanced condition, overlooking the requirement that the opposite-branch product rule R1R4=R2R3R_1 R_4 = R_2 R_3 (or ratio equivalence R1R2=R3R4\frac{R_1}{R_2} = \frac{R_3}{R_4}) must hold true for VC=VDV_C = V_D. When the bridge is unbalanced, you must apply systematic circuit techniques such as mesh analysis or Thévenin's theorem.

REASONING PATH
Your ACEpath teacher’s suggested approach
Bridge Balance Test
  • A bridge is balanced if and only if R1R4=R2R3R_1 R_4 = R_2 R_3, which yields VC−VD=0V_C - V_D = 0.

  • Always compare cross products R1R4R_1 R_4 and R2R3R_2 R_3. If they are not equal, do not set I5=0I_5 = 0.

Method Selection for Unbalanced Bridges
  • When a bridge is unbalanced, current flows through the galvanometer/central branch.

  • Formulate Kirchhoff's voltage law around independent meshes or compute the Thévenin equivalent seen across the central resistor.

CORRECTED PATH
ACEpath Teacher's Demonstration
  1. Test the balance condition: R1R4=(4.00)(2.00)=8.00 Ω2R_1 R_4 = (4.00)(2.00) = 8.00\ \Omega^2, whereas R2R3=(6.00)(8.00)=48.00 Ω2R_2 R_3 = (6.00)(8.00) = 48.00\ \Omega^2. Because 8.00≠48.008.00 \neq 48.00, the bridge is unbalanced.

  2. Set up mesh equations with clockwise currents I1I_1 (mesh A−C−DA-C-D), I2I_2 (mesh C−B−DC-B-D), and I3I_3 (battery loop through A−D−BA-D-B): 17I1−5I2−8I3=017 I_1 - 5 I_2 - 8 I_3 = 0, −5I1+13I2−2I3=0-5 I_1 + 13 I_2 - 2 I_3 = 0, and −8I1−2I2+10I3=E-8 I_1 - 2 I_2 + 10 I_3 = \mathcal{E}.

  3. Solve the linear system for I1I_1 and I2I_2 to find the central branch current: I5=I1−I2=1.00 AI_5 = I_1 - I_2 = 1.00\text{ A}.

  4. Calculate dissipated power via Joule heating: P5=I52R5=(1.00 A)2⋅5.00 Ω=5.00 WP_5 = I_5^2 R_5 = (1.00\text{ A})^2 \cdot 5.00\ \Omega = 5.00\text{ W}.

Final answer

P5=5.00 WP_5 = 5.00\text{ W}

NEXT STEPS
Final Takeaways from Your Teacher
  • Compare the cross-products R1R4R_1 R_4 and R2R3R_2 R_3 first whenever you encounter a bridge network.

  • Practice setting up 3-mesh KVL equations systematically when bridge ratios are unequal.

OverviewACEpath Teacher's Diagnosis

02 The student neglects the interaction from the central coupling resistor R_5 when calculating the node voltages, treating the bridge as two independent parallel voltage dividers.

Sample Student Work

Reviewed by ACEpath Teacher
Step-by-Step Review
Walk Through It with Your Teacher
Incorrect
  1. Step 1

    VC=22.0⋅6.00/(4.00+6.00)=13.2 V  ⟹  VD=22.0⋅2.00/(8.00+2.00)=4.4 VV_C = 22.0 \cdot 6.00 / (4.00 + 6.00) = 13.2\text{ V} \implies V_D = 22.0 \cdot 2.00 / (8.00 + 2.00) = 4.4\text{ V}

    Correct

    (17−5−8−513−2−8−210)(I1I2I3)=(0022.0)\begin{pmatrix} 17 & -5 & -8 \\ -5 & 13 & -2 \\ -8 & -2 & 10 \end{pmatrix} \begin{pmatrix} I_1 \\ I_2 \\ I_3 \end{pmatrix} = \begin{pmatrix} 0 \\ 0 \\ 22.0 \end{pmatrix}

    You calculated VCV_C and VDV_D using the unloaded voltage divider formula, which assumes zero current flows between nodes CC and DD. Because R5R_5 connects these nodes and carries significant current, you must use Kirchhoff's voltage law (mesh analysis) or nodal analysis to account for the branch interaction.

  2. Step 2

    V5=VC−VD=13.2−4.4=8.8 VV_5 = V_C - V_D = 13.2 - 4.4 = 8.8\text{ V}

    Correct

    I5=I1−I2=40(22.5)900=1.00 A  ⟹  V5=I5R5=5.00 VI_5 = I_1 - I_2 = \frac{40(22.5)}{900} = 1.00\text{ A} \implies V_5 = I_5 R_5 = 5.00\text{ V}

    You subtracted the two node voltages correctly according to potential difference definition, but the values of VCV_C and VDV_D were incorrect from treating the bridge as unloaded.

  3. Step 3

    P5=V52/R5=8.82/5.00=15.49 WP_5 = V_5^2 / R_5 = 8.8^2 / 5.00 = 15.49\text{ W}

    Correct

    P5=I52R5=(1.00 A)2(5.00 Ω)=5.00 WP_5 = I_5^2 R_5 = (1.00\text{ A})^2(5.00\ \Omega) = 5.00\text{ W}

    You applied the thermal power formula P=V2RP = \frac{V^2}{R} correctly, but the result is inaccurate because it propagated the incorrect branch voltage from the previous steps.

WHAT YOU DID WELL
Compliments from Your Teacher

You correctly identified that the voltage across the detector branch equals the difference between node potentials VC−VDV_C - V_D.

You used the correct relationship between voltage, resistance, and electrical power dissipation (P=V2RP = \frac{V^2}{R}).

THE ERROR
Where Your ACEpath Teacher Spotted the Mistake
Neglecting bridge loading / Misapplying voltage divider rule

none

WHY IT HAPPENED
ACEpath Teacher's Diagnosis

You treated an unbalanced bridge network as two isolated, unloaded voltage dividers in parallel, neglecting the cross-branch current through coupling resistor R5R_5.

REASONING PATH
Your ACEpath teacher’s suggested approach
Voltage Divider Validity
  • The simple voltage divider formula V2=VtotalR2R1+R2V_2 = V_{\text{total}} \frac{R_2}{R_1 + R_2} strictly applies only when no current leaves or enters the intermediate node.

  • Check if an intermediate node is connected to another active path or load resistor. If it is, use Kirchhoff's laws or a Thévenin equivalent circuit instead.

Mesh KVL Formulation
  • For a planar bridge network with three meshes, sum potential drops around each closed loop: ∑V=0\sum V = 0. Shared resistors must include the opposing mesh current (e.g., (I1−I2)R5(I_1 - I_2)R_5).

  • Set up a system of linear equations for the mesh currents I1,I2,I3I_1, I_2, I_3 and solve for I5=I1−I2I_5 = I_1 - I_2 before computing power.

CORRECTED PATH
ACEpath Teacher's Demonstration
  1. Loop 1 (A−C−D−AA-C-D-A): (R1+R3+R5)I1−R5I2−R3I3=0  ⟹  17I1−5I2−8I3=0(R_1 + R_3 + R_5)I_1 - R_5 I_2 - R_3 I_3 = 0 \implies 17 I_1 - 5 I_2 - 8 I_3 = 0

  2. Loop 2 (C−B−D−CC-B-D-C): −R5I1+(R2+R4+R5)I2−R4I3=0  ⟹  −5I1+13I2−2I3=0-R_5 I_1 + (R_2 + R_4 + R_5)I_2 - R_4 I_3 = 0 \implies -5 I_1 + 13 I_2 - 2 I_3 = 0

  3. Loop 3 (Source-A−D−BA-D-B): −R3I1−R4I2+(R3+R4)I3=E  ⟹  −8I1−2I2+10I3=22.5 V-R_3 I_1 - R_4 I_2 + (R_3 + R_4)I_3 = \mathcal{E} \implies -8 I_1 - 2 I_2 + 10 I_3 = 22.5\text{ V}

  4. Solve for the mesh currents: I1=1.90 AI_1 = 1.90\text{ A}, I2=0.90 AI_2 = 0.90\text{ A}, yielding I5=I1−I2=1.00 AI_5 = I_1 - I_2 = 1.00\text{ A}.

  5. Calculate power dissipation in R5R_5: P5=I52R5=(1.00 A)2⋅5.00 Ω=5.00 WP_5 = I_5^2 R_5 = (1.00\text{ A})^2 \cdot 5.00\ \Omega = 5.00\text{ W}.

Final answer

P5=5.00 WP_5 = 5.00\text{ W}

NEXT STEPS
Final Takeaways from Your Teacher
  • Review when standard series-parallel rules break down in bridge topologies due to cross-branch coupling.

  • Practice formulating mesh current matrices with shared branches, paying special attention to opposing current signs.

  • Solve bridge problems using Thévenin's theorem across the load terminals as an alternative verification technique.

OverviewACEpath Teacher's Diagnosis

03 The student correctly calculates the current through R_5 but forgets to square the current in the power formula, using P = I * R instead of P = I² * R.

Sample Student Work

Reviewed by ACEpath Teacher
Step-by-Step Review
Walk Through It with Your Teacher
Partially correct
  1. Step 1

    37VC−12VD=33037 V_C - 12 V_D = 330 ⟹ −8VC+33VD=110-8 V_C + 33 V_D = 110

  2. Step 2

    VC=10.85 V, VD=5.96 VV_C = 10.85\text{ V},\ V_D = 5.96\text{ V}

  3. Step 3

    I5=(10.85−5.96)/5.00=0.978 AI_5 = (10.85 - 5.96) / 5.00 = 0.978\text{ A}

  4. Step 4

    P5=I5∗R5=0.978∗5.00=4.89 WP_5 = I_5 * R_5 = 0.978 * 5.00 = 4.89\text{ W}

    Correct

    P5=I52R5=(0.978 A)2×5.00 Ω≈4.78 WP_5 = I_5^2 R_5 = (0.978\text{ A})^2 \times 5.00\ \Omega \approx 4.78\text{ W} (or 5.00 W5.00\text{ W} with the nominal 22.5 V22.5\text{ V} source)

    You wrote P5=I5⋅R5P_5 = I_5 \cdot R_5, which computes the potential difference (voltage drop in volts) across the resistor rather than the dissipated thermal power. Joule's heating law requires squaring the current: P=I2RP = I^2 R.

WHAT YOU DID WELL
Compliments from Your Teacher

You correctly set up and solved the nodal equations for the bridge network.

You calculated the accurate branch current passing through the detector resistor R5R_5.

THE ERROR
Where Your ACEpath Teacher Spotted the Mistake
Formula Confusion

You accidentally omitted the exponent in Joule's law, calculating IRI R instead of I2RI^2 R.

WHY IT HAPPENED
ACEpath Teacher's Diagnosis

Confusing the expressions for Ohm's law (V=IRV = I R) and Joule heating power (P=I2R=VI=V2/RP = I^2 R = V I = V^2 / R), leading to reporting the branch voltage drop with units of watts.

REASONING PATH
Your ACEpath teacher’s suggested approach
Check physical dimensions and units
  • Electrical power has units of watts (W=J/s=V⋅A=A2⋅Ω\text{W} = \text{J/s} = \text{V}\cdot\text{A} = \text{A}^2\cdot\Omega), whereas IRI R yields volts (V\text{V}).

  • Always verify that your power formula involves either a squared quantity (I2RI^2 R, V2/RV^2/R) or the product of current and voltage (IVI V).

CORRECTED PATH
ACEpath Teacher's Demonstration
  1. Take the branch current through resistor R5R_5: I5≈0.978 AI_5 \approx 0.978\text{ A} (exact fraction: I5=4445 AI_5 = \frac{44}{45}\text{ A}).

  2. Apply Joule's law of heating: P5=I52R5P_5 = I_5^2 R_5.

  3. Substitute the numerical values: P5=(0.978 A)2×5.00 Ω≈4.78 WP_5 = (0.978\text{ A})^2 \times 5.00\ \Omega \approx 4.78\text{ W} (or using nominal source 22.5 V22.5\text{ V}, I5=1.00 A  ⟹  P5=5.00 WI_5 = 1.00\text{ A} \implies P_5 = 5.00\text{ W}).

Final answer

P5≈4.78 WP_5 \approx 4.78\text{ W} (nominal: 5.00 W5.00\text{ W})

NEXT STEPS
Final Takeaways from Your Teacher
  • Review the three equivalent expressions for thermal power in an ideal resistor: P=VI=I2R=V2RP = V I = I^2 R = \frac{V^2}{R}.

  • Practice checking dimensional consistency on each formula line before writing units.

Lock it in

Similar question

01

A bridge circuit connected across a 12.0 V12.0\text{ V} battery has R1=3.00 ΩR_1 = 3.00\ \Omega, R2=6.00 ΩR_2 = 6.00\ \Omega, R3=5.00 ΩR_3 = 5.00\ \Omega, and R4=10.00 ΩR_4 = 10.00\ \Omega, with a central resistor R5=4.00 ΩR_5 = 4.00\ \Omega. Determine the current I5I_5 through R5R_5 and the power P5P_5 dissipated in it.

Answer

I5=0 AI_5 = 0\text{ A}, P5=0 WP_5 = 0\text{ W}. Check balance: R1R4=(3.00)(10.00)=30.0 Ω2R_1 R_4 = (3.00)(10.00) = 30.0\ \Omega^2 and R2R3=(6.00)(5.00)=30.0 Ω2R_2 R_3 = (6.00)(5.00) = 30.0\ \Omega^2. Because the bridge is balanced, VC=VDV_C = V_D, so no current flows through R5R_5.

02

In a bridge network, nodes AA and BB are held at VA=20.0 VV_A = 20.0\text{ V} and VB=0 VV_B = 0\text{ V}. Resistors are R1=2.00 ΩR_1 = 2.00\ \Omega (AA to CC), R2=8.00 ΩR_2 = 8.00\ \Omega (CC to BB), R3=6.00 ΩR_3 = 6.00\ \Omega (AA to DD), and R4=4.00 ΩR_4 = 4.00\ \Omega (DD to BB). With the central branch CDCD open, what is the open-circuit voltage VCD=VC−VDV_{CD} = V_C - V_D?

Answer

VCD=8.00 VV_{CD} = 8.00\text{ V}. By voltage division: VC=VAR2R1+R2=20.0(810)=16.0 VV_C = V_A \frac{R_2}{R_1 + R_2} = 20.0 \left(\frac{8}{10}\right) = 16.0\text{ V}, and VD=VAR4R3+R4=20.0(410)=8.00 VV_D = V_A \frac{R_4}{R_3 + R_4} = 20.0 \left(\frac{4}{10}\right) = 8.00\text{ V}. Thus VCD=16.0−8.00=8.00 VV_{CD} = 16.0 - 8.00 = 8.00\text{ V}.

03

For the unbalanced bridge in Question 2 (VTh=8.00 VV_{Th} = 8.00\text{ V} across terminals CC and DD), a resistor R5=4.40 ΩR_5 = 4.40\ \Omega is connected between nodes CC and DD. Using Thévenin's theorem, calculate the current I5I_5 and the power P5P_5 dissipated in R5R_5.

Answer

I5=1.00 AI_5 = 1.00\text{ A}, P5=4.40 WP_5 = 4.40\text{ W}. The Thévenin resistance looking into CDCD with source deactivated is RTh=(R1∥R2)+(R3∥R4)=2×810+6×410=1.60+2.40=4.00 ΩR_{Th} = (R_1 \parallel R_2) + (R_3 \parallel R_4) = \frac{2 \times 8}{10} + \frac{6 \times 4}{10} = 1.60 + 2.40 = 4.00\ \Omega. The branch current is I5=VThRTh+R5=8.004.00+4.40=1.00 AI_5 = \frac{V_{Th}}{R_{Th} + R_5} = \frac{8.00}{4.00 + 4.40} = 1.00\text{ A}. Power is P5=I52R5=(1.00)2(4.40)=4.40 WP_5 = I_5^2 R_5 = (1.00)^2 (4.40) = 4.40\text{ W}.

Loading workspace…