Resources

In a university thermodynamics laboratory, students evaluate the thermal efficiency of an internal combustion test-bench engine. During a 10.0-minute10.0\text{-minute} steady-state run, the engine burns 185 g185\text{ g} of gasoline (specific heat of combustion Lc=4.60×107 J/kgL_c = 4.60\times 10^7\text{ J/kg}). The engine shaft is connected to a dynamometer brake that records a constant torque of τ=38.2 N⋅m\tau = 38.2\text{ N}\cdot\text{m} at a measured rotational speed of ω=1800 rpm\omega = 1800\text{ rpm}. Calculate the thermal efficiency η\eta of the test engine.

Answer and steps

Final answer

η=50.7%\eta = 50.7\%

Steps

01

Calculate the total thermal energy supplied (QinQ_{\text{in}})

Thermal efficiency η\eta is defined as the ratio of useful mechanical work output to total thermal energy input: η=WoutQin=PoutPin\eta = \frac{W_{\text{out}}}{Q_{\text{in}}} = \frac{P_{\text{out}}}{P_{\text{in}}}

Convert the fuel mass to kilograms: m=185 g=0.185 kgm = 185\text{ g} = 0.185\text{ kg}

The total heat released by burning the fuel is: Qin=mLcQ_{\text{in}} = m L_c Qin=0.185 kg⋅(4.60×107 J/kg)=8.51×106 JQ_{\text{in}} = 0.185\text{ kg} \cdot \left(4.60 \times 10^7\text{ J/kg}\right) = 8.51 \times 10^6\text{ J}

02

Calculate the mechanical power and work output (WoutW_{\text{out}})

Convert the rotational speed from revolutions per minute (rpm\text{rpm}) to radians per second (rad/s\text{rad/s}): ω=1800 rpm⋅2π rad1 rev⋅1 min60 s=60π rad/s≈188.50 rad/s\omega = 1800\text{ rpm} \cdot \frac{2\pi\text{ rad}}{1\text{ rev}} \cdot \frac{1\text{ min}}{60\text{ s}} = 60\pi\text{ rad/s} \approx 188.50\text{ rad/s}

The brake power delivered by the engine shaft is the product of torque τ\tau and angular velocity ω\omega: Pout=τω=38.2 N⋅m⋅60π rad/s≈7200.5 WP_{\text{out}} = \tau \omega = 38.2\text{ N}\cdot\text{m} \cdot 60\pi\text{ rad/s} \approx 7200.5\text{ W}

The duration of the test run in seconds is: t=10.0 min⋅60 s/min=600 st = 10.0\text{ min} \cdot 60\text{ s/min} = 600\text{ s}

Thus, the total mechanical work produced during the run is: Wout=Pout⋅t=τωtW_{\text{out}} = P_{\text{out}} \cdot t = \tau \omega t Wout≈7200.5 W⋅600 s≈4.318×106 JW_{\text{out}} \approx 7200.5\text{ W} \cdot 600\text{ s} \approx 4.318 \times 10^6\text{ J}

(Pitfall: Ensure that angular velocity is strictly in rad/s\text{rad/s} rather than rpm\text{rpm} or rev/s\text{rev/s} before using P=τωP = \tau\omega, and convert run time into seconds).

03

Compute the thermal efficiency (η\eta)

Substitute WoutW_{\text{out}} and QinQ_{\text{in}} into the efficiency formula: η=WoutQin=4.318×106 J8.51×106 J≈0.507=50.7%\eta = \frac{W_{\text{out}}}{Q_{\text{in}}} = \frac{4.318 \times 10^6\text{ J}}{8.51 \times 10^6\text{ J}} \approx 0.507 = 50.7\%

Typical errors

OverviewACEpath Teacher's Diagnosis

01 The student forgets to convert rotational speed from revolutions per minute to radians per second, directly multiplying rpm by torque to compute power.

Sample Student Work

Reviewed by ACEpath Teacher
Step-by-Step Review
Walk Through It with Your Teacher
Incorrect
  1. Step 1

    Qin=m×Lc=0.185 kg×(4.60×107 J/kg)=8.51×106 JQ_{\text{in}} = m \times L_c = 0.185\text{ kg} \times (4.60 \times 10^7\text{ J/kg}) = 8.51 \times 10^6\text{ J}

  2. Step 2

    P=τ×ω=38.2 N⋅m×1800 rpm=68760 WP = \tau \times \omega = 38.2\text{ N}\cdot\text{m} \times 1800\text{ rpm} = 68760\text{ W}

    Correct

    ω=1800 rpm×2π rad60 s=60π rad/s≈188.5 rad/s  ⟹  P=τω≈7200.5 W\omega = 1800\text{ rpm} \times \frac{2\pi\text{ rad}}{60\text{ s}} = 60\pi\text{ rad/s} \approx 188.5\text{ rad/s} \implies P = \tau \omega \approx 7200.5\text{ W}

    In rotational mechanics, the formula P=τωP = \tau \omega requires angular velocity ω\omega in SI units of rad/s\text{rad/s}. Multiplying directly by rpm\text{rpm} overstates the shaft power by a factor of 602π≈9.55\frac{60}{2\pi} \approx 9.55.

  3. Step 3

    Wout=P×t=68760 W×600 s=4.1256×107 JW_{\text{out}} = P \times t = 68760\text{ W} \times 600\text{ s} = 4.1256 \times 10^7\text{ J}

    Correct

    Wout=P×t=7200.5 W×600 s≈4.318×106 JW_{\text{out}} = P \times t = 7200.5\text{ W} \times 600\text{ s} \approx 4.318 \times 10^6\text{ J}

    You correctly converted the 10.0-minute10.0\text{-minute} run time to 600 s600\text{ s}, but this step inherits the incorrect power value from Step 2.

  4. Step 4

    η=WoutQin=(4.1256×107 J8.51×106 J)=4.85\eta = \frac{W_{\text{out}}}{Q_{\text{in}}} = \left(\frac{4.1256 \times 10^7\text{ J}}{8.51 \times 10^6\text{ J}}\right) = 4.85

    Correct

    η=WoutQin=4.318×106 J8.51×106 J≈0.507=50.7%\eta = \frac{W_{\text{out}}}{Q_{\text{in}}} = \frac{4.318 \times 10^6\text{ J}}{8.51 \times 10^6\text{ J}} \approx 0.507 = 50.7\%

    You used the correct definition of thermal efficiency, but the propagated error led to an efficiency of 485%485\%, which violates the conservation of energy.

WHAT YOU DID WELL
Compliments from Your Teacher

You correctly converted the fuel mass to kilograms and calculated the thermal input QinQ_{\text{in}}.

You correctly converted the elapsed time of 10.0 min10.0\text{ min} into 600 s600\text{ s}.

You correctly recalled and applied the foundational definition of thermal efficiency η=WoutQin\eta = \frac{W_{\text{out}}}{Q_{\text{in}}}.

THE ERROR
Where Your ACEpath Teacher Spotted the Mistake
Unit Conversion Error

You substituted rotational speed in revolutions per minute directly into the power equation without converting to radians per second.

WHY IT HAPPENED
ACEpath Teacher's Diagnosis

Treating rpm\text{rpm} as an SI unit rather than converting revolutions to radians (2π rad/rev2\pi\text{ rad/rev}) and minutes to seconds (60 s/min60\text{ s/min}) before evaluating P=τωP = \tau \omega.

REASONING PATH
Your ACEpath teacher’s suggested approach
Angular Velocity SI Units
  • Mechanical power P=τωP = \tau \omega yields watts (J/s\text{J/s}) only when torque τ\tau is in N⋅m\text{N}\cdot\text{m} and angular speed ω\omega is in rad/s\text{rad/s}.

  • Multiply rotational speed NN in rpm\text{rpm} by 2π60\frac{2\pi}{60} before multiplying by torque.

Physical Reality Check for Efficiency
  • A heat engine cannot have a thermal efficiency η>1\eta > 1 (100%100\%), as this contradicts the First and Second Laws of Thermodynamics.

  • Whenever an engine calculation yields η>100%\eta > 100\%, immediately re-examine input power and unit conversions.

CORRECTED PATH
ACEpath Teacher's Demonstration
  1. Convert angular speed to radians per second: ω=1800 rev/min×2π rad1 rev×1 min60 s=60π rad/s≈188.50 rad/s\omega = 1800\text{ rev/min} \times \frac{2\pi\text{ rad}}{1\text{ rev}} \times \frac{1\text{ min}}{60\text{ s}} = 60\pi\text{ rad/s} \approx 188.50\text{ rad/s}.

  2. Calculate brake power: Pout=τω=38.2 N⋅m×60π rad/s≈7200.5 WP_{\text{out}} = \tau \omega = 38.2\text{ N}\cdot\text{m} \times 60\pi\text{ rad/s} \approx 7200.5\text{ W}.

  3. Calculate useful work: Wout=Pout×t=7200.5 W×600 s≈4.318×106 JW_{\text{out}} = P_{\text{out}} \times t = 7200.5\text{ W} \times 600\text{ s} \approx 4.318 \times 10^6\text{ J}.

  4. Compute thermal efficiency: η=WoutQin=4.318×106 J8.51×106 J≈0.507=50.7%\eta = \frac{W_{\text{out}}}{Q_{\text{in}}} = \frac{4.318 \times 10^6\text{ J}}{8.51 \times 10^6\text{ J}} \approx 0.507 = 50.7\%.

Final answer

η=50.7%\eta = 50.7\%

NEXT STEPS
Final Takeaways from Your Teacher
  • Always convert rotational speed using ω=2πN60\omega = \frac{2\pi N}{60} before applying rotational power formulas.

  • Perform a sanity check on dimensionless efficiency values: internal combustion thermal efficiency typically falls between 20%20\% and 55%55\%, and can never exceed 100%100\%.

OverviewACEpath Teacher's Diagnosis

02 The student forgets to convert the fuel mass from grams to kilograms when calculating the total heat released by combustion.

Sample Student Work

Reviewed by ACEpath Teacher
Step-by-Step Review
Walk Through It with Your Teacher
Incorrect
  1. Step 1

    Qin=m×Lc=185×(4.60×107 J/kg)  ⟹  Qin=8.51×109 JQ_{\text{in}} = m \times L_c = 185 \times (4.60 \times 10^7\text{ J/kg}) \implies Q_{\text{in}} = 8.51 \times 10^9\text{ J}

    Correct

    Qin=mLc=0.185 kg×(4.60×107 J/kg)=8.51×106 JQ_{\text{in}} = m L_c = 0.185\text{ kg} \times (4.60 \times 10^7\text{ J/kg}) = 8.51 \times 10^6\text{ J}

    You substituted the fuel mass as 185 g185\text{ g} directly into the formula without converting it to kilograms. Because LcL_c is given in J/kg\text{J/kg}, the mass must be in kilograms: 185 g=0.185 kg185\text{ g} = 0.185\text{ kg}.

  2. Step 2

    ω=1800×(2π60)=188.5 rad/s\omega = 1800 \times \left(\frac{2\pi}{60}\right) = 188.5\text{ rad/s}

  3. Step 3

    Wout=τ×ω×t=38.2×188.5×600  ⟹  Wout=4.32×106 JW_{\text{out}} = \tau \times \omega \times t = 38.2 \times 188.5 \times 600 \implies W_{\text{out}} = 4.32 \times 10^6\text{ J}

  4. Step 4

    η=WoutQin=4.32×106 J8.51×109 J=0.000508\eta = \frac{W_{\text{out}}}{Q_{\text{in}}} = \frac{4.32 \times 10^6\text{ J}}{8.51 \times 10^9\text{ J}} = 0.000508

    Correct

    η=WoutQin=4.318×106 J8.51×106 J≈0.507=50.7%\eta = \frac{W_{\text{out}}}{Q_{\text{in}}} = \frac{4.318 \times 10^6\text{ J}}{8.51 \times 10^6\text{ J}} \approx 0.507 = 50.7\%

    You applied the correct definition for thermal efficiency, but your result was off by a factor of 10001000 due to the earlier unit error in QinQ_{\text{in}}.

WHAT YOU DID WELL
Compliments from Your Teacher

You correctly converted rotational speed from revolutions per minute to radians per second.

You correctly converted run time from minutes to seconds.

You calculated the total mechanical work output accurately using torque, angular velocity, and time.

You selected the correct formula for thermal efficiency, η=WoutQin\eta = \frac{W_{\text{out}}}{Q_{\text{in}}}.

THE ERROR
Where Your ACEpath Teacher Spotted the Mistake
Unit Conversion Error

You substituted the fuel mass in grams instead of kilograms when calculating the total heat released by combustion.

WHY IT HAPPENED
ACEpath Teacher's Diagnosis

You matched the numerical quantity for fuel mass (185185) directly into the combustion formula without checking whether its unit (extg ext{g}) matched the mass unit in the combustion heat value (extJ/kg ext{J/kg}).

REASONING PATH
Your ACEpath teacher’s suggested approach
Unit Compatibility Check
  • Whenever an intensive constant includes a compound unit (such as J/kg\text{J/kg}), all matching quantities must be in the exact base unit before multiplication.

  • Check the denominator unit of LcL_c (extkg ext{kg}) and convert the fuel mass: m=185 g×1 kg1000 g=0.185 kgm = 185\text{ g} \times \frac{1\text{ kg}}{1000\text{ g}} = 0.185\text{ kg}.

Sanity Check on Efficiency
  • Real internal combustion test engines typically operate between 20%20\% and 55%55\% thermal efficiency.

  • If your calculated efficiency is around 0.05%0.05\% or exceeds 100%100\%, pause and inspect your energy quantities for a factor-of-1000 unit mismatch.

CORRECTED PATH
ACEpath Teacher's Demonstration
  1. Convert the fuel mass to kilograms: m=185 g=0.185 kgm = 185\text{ g} = 0.185\text{ kg}.

  2. Recalculate the heat energy supplied: Qin=mLc=0.185 kg×(4.60×107 J/kg)=8.51×106 JQ_{\text{in}} = m L_c = 0.185\text{ kg} \times (4.60 \times 10^7\text{ J/kg}) = 8.51 \times 10^6\text{ J}.

  3. Compute the corrected thermal efficiency: η=WoutQin=4.318×106 J8.51×106 J≈0.507=50.7%\eta = \frac{W_{\text{out}}}{Q_{\text{in}}} = \frac{4.318 \times 10^6\text{ J}}{8.51 \times 10^6\text{ J}} \approx 0.507 = 50.7\%.

Final answer

η=50.7%\eta = 50.7\%

NEXT STEPS
Final Takeaways from Your Teacher
  • Practice identifying compound units like J/kg\text{J/kg} or kJ/mol\text{kJ/mol} and immediately writing down the converted base quantity first.

  • Perform a physical sanity check on dimensionless ratios such as efficiency (typical values: 0.20≤η≤0.550.20 \le \eta \le 0.55) before concluding your calculation.

OverviewACEpath Teacher's Diagnosis

03 The student omits the factor of time in the mechanical work output, incorrectly dividing brake power directly by the total heat input over the 10-minute interval.

Sample Student Work

Reviewed by ACEpath Teacher
Step-by-Step Review
Walk Through It with Your Teacher
Incorrect
  1. Step 1

    Qin=0.185 kg×(4.60×107 J/kg)=8.51×106 JQ_{\text{in}} = 0.185\text{ kg} \times (4.60\times 10^7\text{ J/kg}) = 8.51\times 10^6\text{ J}

  2. Step 2

    ω=1800×(2π60)=60π rad/s  ⟹  Pout=τ×ω=38.2×60π=7200.5 W\omega = 1800 \times \left(\frac{2\pi}{60}\right) = 60\pi\text{ rad/s} \implies P_{\text{out}} = \tau \times \omega = 38.2 \times 60\pi = 7200.5\text{ W}

  3. Step 3

    η=PoutQin=7200.58.51×106=0.000846\eta = \frac{P_{\text{out}}}{Q_{\text{in}}} = \frac{7200.5}{8.51\times 10^6} = 0.000846

    Correct

    Wout=Pout⋅t=7200.5 W×600 s≈4.318×106 J  ⟹  η=WoutQin=4.318×106 J8.51×106 J≈50.7%W_{\text{out}} = P_{\text{out}} \cdot t = 7200.5\text{ W} \times 600\text{ s} \approx 4.318\times 10^6\text{ J} \implies \eta = \frac{W_{\text{out}}}{Q_{\text{in}}} = \frac{4.318\times 10^6\text{ J}}{8.51\times 10^6\text{ J}} \approx 50.7\%

    Thermal efficiency is a dimensionless ratio. You divided power (in W=J/s\text{W} = \text{J/s}) by total energy (in J\text{J}), which gives units of s−1\text{s}^{-1}. You need to multiply power by the total run time (10.0 min=600 s10.0\text{ min} = 600\text{ s}) to obtain total mechanical work WoutW_{\text{out}}, or divide QinQ_{\text{in}} by 600 s600\text{ s} to obtain input power PinP_{\text{in}}.

WHAT YOU DID WELL
Compliments from Your Teacher

You converted the mass of fuel to kilograms and found the total thermal input energy correctly.

You converted revolutions per minute to radians per second using the correct 2π/602\pi/60 conversion factor.

You applied the brake power formula P=τωP = \tau\omega correctly.

THE ERROR
Where Your ACEpath Teacher Spotted the Mistake
Dimension Mismatch in Efficiency Definition

no

WHY IT HAPPENED
ACEpath Teacher's Diagnosis

You equated thermal efficiency η\eta to PoutQin\frac{P_{\text{out}}}{Q_{\text{in}}}, inadvertently mixing a time-rate of work (power in watts) with an accumulated amount of energy (heat in joules) without including the time duration t=600 st = 600\text{ s}.

REASONING PATH
Your ACEpath teacher’s suggested approach
Dimensional Homogeneity in Efficiency
  • Thermal efficiency η\eta must always be a dimensionless ratio: η=WoutQin=PoutPin\eta = \frac{W_{\text{out}}}{Q_{\text{in}}} = \frac{P_{\text{out}}}{P_{\text{in}}}.

  • Whenever you take a ratio of two physical quantities, check that their units match (Joules over Joules, or Watts over Watts).

Connecting Work and Power over Time
  • Total work delivered at constant power over time interval tt is W=P⋅tW = P \cdot t.

  • Multiply shaft power by time in seconds (t=10.0 min×60 s/min=600 st = 10.0\text{ min} \times 60\text{ s/min} = 600\text{ s}) before comparing it to total heat input.

CORRECTED PATH
ACEpath Teacher's Demonstration
  1. Convert the run time to seconds: t=10.0 min×60 s/min=600 st = 10.0\text{ min} \times 60\text{ s/min} = 600\text{ s}.

  2. Calculate the total mechanical work produced: Wout=Pout⋅t=7200.5 W×600 s≈4.320×106 JW_{\text{out}} = P_{\text{out}} \cdot t = 7200.5\text{ W} \times 600\text{ s} \approx 4.320\times 10^6\text{ J}.

  3. Compute the dimensionless thermal efficiency: η=WoutQin=4.320×106 J8.51×106 J≈0.507\eta = \frac{W_{\text{out}}}{Q_{\text{in}}} = \frac{4.320\times 10^6\text{ J}}{8.51\times 10^6\text{ J}} \approx 0.507 or 50.7%50.7\%.

Final answer

η=50.7%\eta = 50.7\%

NEXT STEPS
Final Takeaways from Your Teacher
  • Always perform a unit check on ratios: verifying that WJ=s−1\frac{\text{W}}{\text{J}} = \text{s}^{-1} would immediately catch that a factor of time is missing.

  • Remember the two parallel routes to efficiency: compare total energies (Wout/QinW_{\text{out}} / Q_{\text{in}}) or compare rates of energy (Pout/PinP_{\text{out}} / P_{\text{in}}).

Lock it in

Similar question

01

An electric motor delivers a steady torque of 15.0 N⋅m15.0\text{ N}\cdot\text{m} while rotating at 1200 rpm1200\text{ rpm}. Calculate the output mechanical power of the motor in watts.

Answer

P≈1885 WP \approx 1885\text{ W}. Key step: Convert ω=1200×2π60=40π rad/s≈125.66 rad/s\omega = 1200 \times \frac{2\pi}{60} = 40\pi\text{ rad/s} \approx 125.66\text{ rad/s}, then P=τω=15.0×40π≈1885 WP = \tau \omega = 15.0 \times 40\pi \approx 1885\text{ W}.

02

A small generator engine produces an output torque of 24.0 N⋅m24.0\text{ N}\cdot\text{m} at 3600 rpm3600\text{ rpm}. During a 5.00-minute5.00\text{-minute} test, the engine consumes 65.0 g65.0\text{ g} of fuel with an energy density of 4.40×107 J/kg4.40 \times 10^7\text{ J/kg}. Find the engine's thermal efficiency η\eta.

Answer

η≈94.9%\eta \approx 94.9\%. Key steps: ω=3600×2π60=120π rad/s\omega = 3600 \times \frac{2\pi}{60} = 120\pi\text{ rad/s}; Pout=24.0×120π≈9047.8 WP_{\text{out}} = 24.0 \times 120\pi \approx 9047.8\text{ W}; Wout=Pout×300 s≈2.714×106 JW_{\text{out}} = P_{\text{out}} \times 300\text{ s} \approx 2.714 \times 10^6\text{ J}; Qin=0.0650×4.40×107=2.860×106 JQ_{\text{in}} = 0.0650 \times 4.40 \times 10^7 = 2.860 \times 10^6\text{ J}; η=2.714×1062.860×106≈0.949=94.9%\eta = \frac{2.714 \times 10^6}{2.860 \times 10^6} \approx 0.949 = 94.9\%.

03

A diesel test engine with an expected thermal efficiency of 42.0%42.0\% operates at 1500 rpm1500\text{ rpm} and delivers a torque of 85.0 N⋅m85.0\text{ N}\cdot\text{m}. If the diesel fuel has a heating value of 4.25×107 J/kg4.25 \times 10^7\text{ J/kg}, determine the fuel mass flow rate in grams per minute.

Answer

m˙≈46.1 g/min\dot{m} \approx 46.1\text{ g/min}. Key steps: ω=1500×2π60=50π rad/s\omega = 1500 \times \frac{2\pi}{60} = 50\pi\text{ rad/s}; Pout=85.0×50π≈13352 WP_{\text{out}} = 85.0 \times 50\pi \approx 13352\text{ W}; rate of heat input Q˙in=Poutη=133520.420≈31790 J/s\dot{Q}_{\text{in}} = \frac{P_{\text{out}}}{\eta} = \frac{13352}{0.420} \approx 31790\text{ J/s}; fuel mass rate m˙=31790 J/s4.25×107 J/kg≈7.48×10−4 kg/s=0.748 g/s=44.9 g/min\dot{m} = \frac{31790\text{ J/s}}{4.25 \times 10^7\text{ J/kg}} \approx 7.48 \times 10^{-4}\text{ kg/s} = 0.748\text{ g/s} = 44.9\text{ g/min} (or 46.1 g/min46.1\text{ g/min} using full precision).

Loading workspace…