Resources

A miniature electric stepper motor delivers a continuous driving torque to a precision drive shaft. In the manufacturer's technical datasheet, the maximum torque output is rated as τ=85.0 cN⋅m\tau = 85.0\text{ cN}\cdot\text{m}. If the drive shaft is attached to a cylindrical capstan with a diameter of D=34.0 mmD = 34.0\text{ mm}, determine the maximum tangential force FF (in Newtons, N\text{N}) that can be exerted at the outer surface of the capstan.

Answer and steps

Final answer

F=50.0 NF = 50.0\text{ N}

Steps

01

Identify the relationship between torque and force

Torque (τ\tau) produced by a tangential force (FF) acting at a distance rr from the axis of rotation is given by:

τ=F⋅r\tau = F \cdot r

Rearranging the formula to solve for the tangential force gives:

F=τrF = \frac{\tau}{r}


02

Convert the given quantities to standard SI units

  1. Torque (τ\tau): The prefix "c" stands for centi- (10−210^{-2}). Therefore: τ=85.0 cN⋅m=85.0×10−2 N⋅m=0.850 N⋅m\tau = 85.0\text{ cN}\cdot\text{m} = 85.0 \times 10^{-2}\text{ N}\cdot\text{m} = 0.850\text{ N}\cdot\text{m}
  2. Radius (rr): The given dimension is the diameter D=34.0 mmD = 34.0\text{ mm}. The radius is half of the diameter: r=D2=34.0 mm2=17.0 mmr = \frac{D}{2} = \frac{34.0\text{ mm}}{2} = 17.0\text{ mm} Converting millimeters to meters (1 mm=10−3 m1\text{ mm} = 10^{-3}\text{ m}): r=17.0×10−3 m=0.0170 mr = 17.0 \times 10^{-3}\text{ m} = 0.0170\text{ m}

Common Pitfall: Be careful not to use the diameter DD directly in place of the radius rr, and ensure non-standard unit prefixes like centinewtons (cN\text{cN}) are converted to newtons (N\text{N}).


03

Calculate the maximum tangential force

Substitute the values in SI units into the rearranged formula:

F=0.850 N⋅m0.0170 m=50.0 NF = \frac{0.850\text{ N}\cdot\text{m}}{0.0170\text{ m}} = 50.0\text{ N}

Typical errors

OverviewACEpath Teacher's Diagnosis

01 The student uses the diameter directly instead of the radius in the torque relation, resulting in a calculated force of 25.0 N.

Sample Student Work

Reviewed by ACEpath Teacher
Step-by-Step Review
Walk Through It with Your Teacher
Incorrect
  1. Step 1

    τ=85.0 cN⋅m=0.850 N⋅m  ⟹  D=34.0 mm=0.0340 m\tau = 85.0\text{ cN}\cdot\text{m} = 0.850\text{ N}\cdot\text{m} \implies D = 34.0\text{ mm} = 0.0340\text{ m}

  2. Step 2

    F=τDF = \frac{\tau}{D}

    Correct

    F=τr=2τDF = \frac{\tau}{r} = \frac{2\tau}{D}

    The lever arm of a tangential force acting on the outer cylinder surface is the perpendicular distance from the center axis to the perimeter, which is the radius r=D2r = \frac{D}{2}, not the diameter DD.

  3. Step 3

    F=0.8500.0340=25.0 NF = \frac{0.850}{0.0340} = 25.0\text{ N}

    Correct

    F=0.850 N⋅m0.0170 m=50.0 NF = \frac{0.850\text{ N}\cdot\text{m}}{0.0170\text{ m}} = 50.0\text{ N}

    Your arithmetic was carried out correctly according to your formula, but substituting the diameter instead of the radius led to an answer of 25.0 N25.0\text{ N} instead of 50.0 N50.0\text{ N}.

WHAT YOU DID WELL
Compliments from Your Teacher

You correctly converted centinewton-meters into standard newton-meters.

You correctly converted millimeters into meters.

You recognized the inverse relationship between force and distance for a given torque.

THE ERROR
Where Your ACEpath Teacher Spotted the Mistake
Radius vs. Diameter in Torque Formula

no

WHY IT HAPPENED
ACEpath Teacher's Diagnosis

You substituted the diameter DD directly as the moment arm instead of using the radius r=D2r = \frac{D}{2} measured from the axis of rotation to the point of force application.

REASONING PATH
Your ACEpath teacher’s suggested approach
Moment Arm Reference Point
  • Torque is defined as τ=F⋅r\tau = F \cdot r, where rr is the perpendicular distance from the axis of rotation to the line of action of the force.

  • When given a cylindrical diameter DD, immediately divide by 22 to find the radius r=D2r = \frac{D}{2} before calculating torque or tangential force.

CORRECTED PATH
ACEpath Teacher's Demonstration
  1. Find the radius of the capstan: r=D2=0.0340 m2=0.0170 mr = \frac{D}{2} = \frac{0.0340\text{ m}}{2} = 0.0170\text{ m}.

  2. Apply the tangential torque relation: τ=F⋅r  ⟹  F=τr\tau = F \cdot r \implies F = \frac{\tau}{r}.

  3. Substitute the values in SI units: F=0.850 N⋅m0.0170 m=50.0 NF = \frac{0.850\text{ N}\cdot\text{m}}{0.0170\text{ m}} = 50.0\text{ N}.

Final answer

F=50.0 NF = 50.0\text{ N}

NEXT STEPS
Final Takeaways from Your Teacher
  • Always draw or visualize the circular cross-section and mark the rotation axis at the center to confirm whether a given dimension is a radius or a diameter.

  • Divide the diameter by 22 as the very first step whenever a problem provides diameter but rotational formulas require the radial distance rr.

OverviewACEpath Teacher's Diagnosis

02 The student misinterprets the prefix centi (c) as milli (m) or 10⁻³, converting 85.0 cN·m to 0.0850 N·m and obtaining 5.00 N.

Sample Student Work

Reviewed by ACEpath Teacher
Step-by-Step Review
Walk Through It with Your Teacher
Incorrect
  1. Step 1

    r=D2=34.0 mm2=17.0 mm=0.0170 mr = \frac{D}{2} = \frac{34.0\text{ mm}}{2} = 17.0\text{ mm} = 0.0170\text{ m}

  2. Step 2

    τ=85.0 cN⋅m=85.0×10−3 N⋅m=0.0850 N⋅m\tau = 85.0\text{ cN}\cdot\text{m} = 85.0 \times 10^{-3}\text{ N}\cdot\text{m} = 0.0850\text{ N}\cdot\text{m}

    Correct

    τ=85.0 cN⋅m=85.0×10−2 N⋅m=0.850 N⋅m\tau = 85.0\text{ cN}\cdot\text{m} = 85.0 \times 10^{-2}\text{ N}\cdot\text{m} = 0.850\text{ N}\cdot\text{m}

    You converted centinewton-meters (cN⋅m\text{cN}\cdot\text{m}) using a factor of 10−310^{-3}, which corresponds to milli (m\text{m}). The prefix centi (c\text{c}) denotes hundredths (10−210^{-2}).

  3. Step 3

    F=τr=0.08500.0170=5.00 NF = \frac{\tau}{r} = \frac{0.0850}{0.0170} = 5.00\text{ N}

    Correct

    F=τr=0.850 N⋅m0.0170 m=50.0 NF = \frac{\tau}{r} = \frac{0.850\text{ N}\cdot\text{m}}{0.0170\text{ m}} = 50.0\text{ N}

    Your relationship F=τrF = \frac{\tau}{r} and arithmetic were correct, but the result was scaled down by a factor of 10 due to the earlier unit conversion mistake.

WHAT YOU DID WELL
Compliments from Your Teacher

You correctly identified the capstan radius by taking half of the given diameter.

You converted millimeters to meters accurately using 10−3 m/mm10^{-3}\text{ m/mm}.

You set up the correct physical formula relating torque, tangential force, and radius: F=τrF = \frac{\tau}{r}.

THE ERROR
Where Your ACEpath Teacher Spotted the Mistake
SI Prefix Confusion (centi vs. milli)

You substituted 10−310^{-3} instead of 10−210^{-2} for the prefix centi (c\text{c}).

WHY IT HAPPENED
ACEpath Teacher's Diagnosis

You conflated the SI prefix centi (c=10−2\text{c} = 10^{-2}) with milli (m=10−3\text{m} = 10^{-3}), likely because centinewton is a less commonly encountered unit than centimeter or millinewton.

REASONING PATH
Your ACEpath teacher’s suggested approach
SI Prefix Definition
  • centi-(c)=10−2=1100\text{centi-} (\text{c}) = 10^{-2} = \frac{1}{100} and milli-(m)=10−3=11000\text{milli-} (\text{m}) = 10^{-3} = \frac{1}{1000}.

  • Whenever you encounter a prefix attached to any base or derived unit (such as cN\text{cN} or cL\text{cL}), replace c\text{c} directly with 10−210^{-2} before entering it into your calculations.

CORRECTED PATH
ACEpath Teacher's Demonstration
  1. Convert torque using c=10−2\text{c} = 10^{-2}: τ=85.0×10−2 N⋅m=0.850 N⋅m\tau = 85.0 \times 10^{-2}\text{ N}\cdot\text{m} = 0.850\text{ N}\cdot\text{m}.

  2. Substitute the corrected torque and the radius into the force equation: F=0.850 N⋅m0.0170 m=50.0 NF = \frac{0.850\text{ N}\cdot\text{m}}{0.0170\text{ m}} = 50.0\text{ N}.

Final answer

F=50.0 NF = 50.0\text{ N}

NEXT STEPS
Final Takeaways from Your Teacher
  • Review the standard SI decimal prefixes, paying special attention to centi (10−210^{-2}) and milli (10−310^{-3}).

  • Practice separating unfamiliar combined units (like cN⋅m\text{cN}\cdot\text{m}) into prefix and base unit before substituting numerical values.

OverviewACEpath Teacher's Diagnosis

03 The student inverts the relationship between force, torque, and lever arm, multiplying torque by radius instead of dividing.

Sample Student Work

Reviewed by ACEpath Teacher
Step-by-Step Review
Walk Through It with Your Teacher
Incorrect
  1. Step 1

    r=34.0 mm/2=17.0 mm=0.0170 m  ⟹  τ=85.0 cN⋅m=0.850 N⋅mr = 34.0\text{ mm} / 2 = 17.0\text{ mm} = 0.0170\text{ m} \implies \tau = 85.0\text{ cN}\cdot\text{m} = 0.850\text{ N}\cdot\text{m}

  2. Step 2

    F=τ×rF = \tau \times r

    Correct

    F=τrF = \frac{\tau}{r}

    The definition of torque for a tangential force is τ=F⋅r\tau = F \cdot r. Rearranging for force requires dividing torque by radius (F=τrF = \frac{\tau}{r}), not multiplying them.

  3. Step 3

    F=0.850×0.0170=0.0145 NF = 0.850 \times 0.0170 = 0.0145\text{ N}

    Correct

    F=0.850 N⋅m0.0170 m=50.0 NF = \frac{0.850\text{ N}\cdot\text{m}}{0.0170\text{ m}} = 50.0\text{ N}

    Your arithmetic was carried out accurately for the formula you chose, but the numerical result is incorrect due to the inverted formula in Step 2.

WHAT YOU DID WELL
Compliments from Your Teacher

You correctly identified that the lever arm is the radius, which is half of the capstan diameter.

You correctly converted millimeters to meters using 1 mm=10−3 m1\text{ mm} = 10^{-3}\text{ m}.

You correctly handled the centi- prefix to convert centinewton-meters to newton-meters.

THE ERROR
Where Your ACEpath Teacher Spotted the Mistake
Inverted Formula / Multiplication Instead of Division

You set up F=τ⋅rF = \tau \cdot r instead of isolating FF from τ=F⋅r\tau = F \cdot r.

WHY IT HAPPENED
ACEpath Teacher's Diagnosis

You conflated the roles of force and torque in the torque equation, treating force as a product of torque and distance rather than as the quotient of torque divided by the lever arm.

REASONING PATH
Your ACEpath teacher’s suggested approach
Fundamental Definition of Torque
  • Torque is force multiplied by perpendicular lever arm: τ=F⋅r\tau = F \cdot r.

  • Always write down the base definition τ=F⋅r\tau = F \cdot r before isolating the unknown variable.

Dimensional Analysis Check
  • The units of torque are N⋅m\text{N}\cdot\text{m}, while the units of force are N\text{N}.

  • Check units during algebraic rearrangement: N⋅mm=N\frac{\text{N}\cdot\text{m}}{\text{m}} = \text{N}. Multiplying gives (N⋅m)⋅m=N⋅m2(\text{N}\cdot\text{m}) \cdot \text{m} = \text{N}\cdot\text{m}^2, which reveals the algebraic error immediately.

CORRECTED PATH
ACEpath Teacher's Demonstration
  1. State the definition of torque for a tangential force: τ=F⋅r\tau = F \cdot r.

  2. Divide both sides by the radius rr: F=τrF = \frac{\tau}{r}.

  3. Substitute the converted SI values: F=0.850 N⋅m0.0170 mF = \frac{0.850\text{ N}\cdot\text{m}}{0.0170\text{ m}}.

  4. Calculate the quotient: F=50.0 NF = 50.0\text{ N}.

Final answer

F=50.0 NF = 50.0\text{ N}

NEXT STEPS
Final Takeaways from Your Teacher
  • Practice isolating variables algebraically from three-variable physics definitions like τ=F⋅r\tau = F \cdot r, P=F⋅vP = F \cdot v, and W=F⋅dW = F \cdot d.

  • Carry units through your equations as an automatic check to verify that your final answer yields Newtons (N\text{N}) rather than N⋅m2\text{N}\cdot\text{m}^2.

Lock it in

Similar question

01

A winch drum with a diameter of D=12.0 cmD = 12.0\text{ cm} is driven by an electric motor producing a torque of τ=36.0 N⋅m\tau = 36.0\text{ N}\cdot\text{m}. Calculate the tension force TT exerted on the cable wound around the drum.

Answer

T=600 NT = 600\text{ N}.

  1. Calculate the radius: r=D2=0.120 m2=0.060 mr = \frac{D}{2} = \frac{0.120\text{ m}}{2} = 0.060\text{ m}.
  2. Solve for tension force: T=τr=36.0 N⋅m0.060 m=600 NT = \frac{\tau}{r} = \frac{36.0\text{ N}\cdot\text{m}}{0.060\text{ m}} = 600\text{ N}.
02

A mechanic applies a tangential force of 160 N160\text{ N} to the outer rim of a circular handwheel. If the handwheel requires a torque of 24.0 N⋅m24.0\text{ N}\cdot\text{m} to turn an adjustment valve, what is the minimum diameter DD of the handwheel in centimeters?

Answer

D=30.0 cmD = 30.0\text{ cm}.

  1. Find the required radius: r=τF=24.0 N⋅m160 N=0.150 m=15.0 cmr = \frac{\tau}{F} = \frac{24.0\text{ N}\cdot\text{m}}{160\text{ N}} = 0.150\text{ m} = 15.0\text{ cm}.
  2. Calculate diameter: D=2r=2×15.0 cm=30.0 cmD = 2r = 2 \times 15.0\text{ cm} = 30.0\text{ cm}.
03

A dual-step pulley consists of an inner axle of diameter d=20.0 mmd = 20.0\text{ mm} and an outer ring of diameter D=80.0 mmD = 80.0\text{ mm}. A tangential braking force of 45.0 N45.0\text{ N} is applied to the outer ring. What maximum tangential load force FloadF_{\text{load}} can be supported by a cord wrapped around the inner axle at static equilibrium?

Answer

Fload=180 NF_{\text{load}} = 180\text{ N}.

  1. Radii are router=80.0 mm2=40.0 mmr_{\text{outer}} = \frac{80.0\text{ mm}}{2} = 40.0\text{ mm} and rinner=20.0 mm2=10.0 mmr_{\text{inner}} = \frac{20.0\text{ mm}}{2} = 10.0\text{ mm}.
  2. Balance torques about the central axis: τouter=τinner  ⟹  Fbrake⋅router=Fload⋅rinner\tau_{\text{outer}} = \tau_{\text{inner}} \implies F_{\text{brake}} \cdot r_{\text{outer}} = F_{\text{load}} \cdot r_{\text{inner}}.
  3. Solve for FloadF_{\text{load}}: Fload=45.0 N×40.0 mm10.0 mm=180 NF_{\text{load}} = 45.0\text{ N} \times \frac{40.0\text{ mm}}{10.0\text{ mm}} = 180\text{ N}.
Loading workspace…