Resources

In an analytical chemistry laboratory, a student monitors the pseudo-first-order decomposition of crystal violet dye by measuring absorbance A(t)A(t) with a spectrophotometer at a wavelength of 590 nm590\text{ nm}. The calibrated spectrophotometer records the following experimental baseline data: at t=0 st = 0\text{ s}, A(0)=0.840A(0) = 0.840; at t=60 st = 60\text{ s}, A(60)=0.504A(60) = 0.504; at t=120 st = 120\text{ s}, A(120)=0.302A(120) = 0.302. Verify that the ratio of successive absorbance values confirms an exponential decay model of the form A(t)=a⋅bt/60A(t) = a \cdot b^{t/60}, identify the experimental decay factor bb, write the function A(t)A(t), and calculate the expected absorbance at t=180 st = 180\text{ s}.

Answer and steps

Final answer

A(60)A(0)=0.5040.840=0.600\frac{A(60)}{A(0)} = \frac{0.504}{0.840} = 0.600 and A(120)A(60)=0.3020.504≈0.600\frac{A(120)}{A(60)} = \frac{0.302}{0.504} \approx 0.600, confirming exponential decay; A(t)=0.840⋅(0.600)t/60A(t) = 0.840 \cdot (0.600)^{t/60}; at t=180 st = 180\text{ s}, A(180)=0.181A(180) = 0.181.

Steps

01

Test for Exponential Decay Using Constant Ratios

An exponential model of the form A(t)=a⋅bt/ΔtA(t) = a \cdot b^{t/\Delta t} requires that the output values change by a constant multiplicative factor over equal increments of time Δt\Delta t. Here, the data points are recorded at uniform intervals of Δt=60 s\Delta t = 60\text{ s}:

  • Between t=0 st = 0\text{ s} and t=60 st = 60\text{ s}: A(60)A(0)=0.5040.840=0.600\frac{A(60)}{A(0)} = \frac{0.504}{0.840} = 0.600
  • Between t=60 st = 60\text{ s} and t=120 st = 120\text{ s}: A(120)A(60)=0.3020.504≈0.5992≈0.600\frac{A(120)}{A(60)} = \frac{0.302}{0.504} \approx 0.5992 \approx 0.600

Since the ratio of successive absorbance values is constant (to three significant figures), the data confirms an exponential decay model.


02

Identify the Parameters and Construct the Model

  • Initial value (aa): The absorbance at t=0 st = 0\text{ s} gives the leading coefficient: a=A(0)=0.840a = A(0) = 0.840
  • Decay factor per 60 s60\text{ s} (bb): The constant ratio per 60 s60\text{ s} interval is: b=0.600b = 0.600

Substituting aa and bb into the given form yields the model: A(t)=0.840⋅(0.600)t/60A(t) = 0.840 \cdot (0.600)^{t/60}

Common Pitfall: Do not use btb^t directly when tt is measured in seconds and the ratio is measured over an interval of 60 s60\text{ s}. The exponent must be t60\frac{t}{60} so that each increase of 60 s60\text{ s} corresponds to multiplying by the factor bb once.


03

Calculate Expected Absorbance at t=180 st = 180\text{ s}

Substitute t=180t = 180 into the model: A(180)=0.840⋅(0.600)180/60=0.840⋅(0.600)3A(180) = 0.840 \cdot (0.600)^{180/60} = 0.840 \cdot (0.600)^3

Evaluate the power and multiply: (0.600)3=0.216(0.600)^3 = 0.216 A(180)=0.840⋅0.216=0.18144≈0.181A(180) = 0.840 \cdot 0.216 = 0.18144 \approx 0.181

Typical errors

OverviewACEpath Teacher's Diagnosis

01 The student misinterprets the base decay factor as the decay rate percentage lost rather than the remaining fraction, setting b equal to 0.40.

Sample Student Work

Reviewed by ACEpath Teacher
Step-by-Step Review
Walk Through It with Your Teacher
Partially correct
  1. Step 1

    A(60)A(0)=0.5040.840=0.60  ⟹  A(120)A(60)=0.3020.504≈0.60  ⟹  \frac{A(60)}{A(0)} = \frac{0.504}{0.840} = 0.60 \implies \frac{A(120)}{A(60)} = \frac{0.302}{0.504} \approx 0.60 \implies The ratio is constant, confirming exponential decay.

  2. Step 2

    b=1−0.60=0.40b = 1 - 0.60 = 0.40

    Correct

    b=0.600b = 0.600

    In an exponential model A(t)=a⋅bt/ΔtA(t) = a \cdot b^{t/\Delta t}, the base bb is the multiplier (decay factor) representing the fraction that remains after each time interval Δt\Delta t. The ratio A(60)A(0)=0.60\frac{A(60)}{A(0)} = 0.60 is already the decay factor bb. Subtracting it from 11 gives the decay rate (r=0.40r = 0.40 or 40%40\% decrease), not the base multiplier bb.

  3. Step 3

    A(t)=0.840⋅(0.40)t/60A(t) = 0.840 \cdot (0.40)^{t/60}

    Correct

    A(t)=0.840⋅(0.600)t/60A(t) = 0.840 \cdot (0.600)^{t/60}

    Your function structure and exponent are set up properly, but the equation uses your incorrect base b=0.40b = 0.40 instead of b=0.600b = 0.600.

  4. Step 4

    A(180)=0.840⋅(0.40)3=0.840⋅0.064=0.054A(180) = 0.840 \cdot (0.40)^3 = 0.840 \cdot 0.064 = 0.054

    Correct

    A(180)=0.840⋅(0.600)3=0.840⋅0.216≈0.181A(180) = 0.840 \cdot (0.600)^3 = 0.840 \cdot 0.216 \approx 0.181

    You evaluated the power and product accurately for your model, but the value is affected by using the incorrect base b=0.40b = 0.40.

WHAT YOU DID WELL
Compliments from Your Teacher

You correctly calculated the ratio of consecutive absorbance values to confirm exponential decay.

You correctly identified the initial baseline absorbance value as a=0.840a = 0.840.

You correctly structured the exponent as t60\frac{t}{60} to match the 60-second measurement intervals.

THE ERROR
Where Your ACEpath Teacher Spotted the Mistake
Decay factor vs decay rate confusion

no

WHY IT HAPPENED
ACEpath Teacher's Diagnosis

You conflated the decay factor bb (the multiplier or remaining fraction) with the decay rate rr (the fraction lost per period). Because b=1−rb = 1 - r, you calculated 1−0.60=0.401 - 0.60 = 0.40, treating the ratio 0.600.60 as if it were the rate of decay rr rather than the decay factor bb itself.

REASONING PATH
Your ACEpath teacher’s suggested approach
Decay Factor vs. Decay Rate
  • For exponential decay, the successive ratio yk+1yk\frac{y_{k+1}}{y_k} is the decay factor bb (remaining proportion). The decay rate is r=1−br = 1 - b (lost proportion). The base of y=a⋅bxy = a \cdot b^x is always bb, never rr.

  • Take the constant ratio directly as the base bb. Only subtract from 11 if a problem gives you a percentage decrease and you need to find b=1−rb = 1 - r.

CORRECTED PATH
ACEpath Teacher's Demonstration
  1. The constant ratio between intervals of Δt=60 s\Delta t = 60\text{ s} is b=A(60)A(0)=0.600b = \frac{A(60)}{A(0)} = 0.600.

  2. Substitute a=0.840a = 0.840 and b=0.600b = 0.600 into the model: A(t)=0.840⋅(0.600)t/60A(t) = 0.840 \cdot (0.600)^{t/60}.

  3. Evaluate at t=180 st = 180\text{ s}: A(180)=0.840⋅(0.600)180/60=0.840⋅(0.600)3A(180) = 0.840 \cdot (0.600)^{180/60} = 0.840 \cdot (0.600)^3.

  4. Compute the value: 0.840⋅0.216=0.18144≈0.1810.840 \cdot 0.216 = 0.18144 \approx 0.181.

Final answer

A(t)=0.840⋅(0.600)t/60A(t) = 0.840 \cdot (0.600)^{t/60} and A(180)≈0.181A(180) \approx 0.181

NEXT STEPS
Final Takeaways from Your Teacher
  • Review the distinction between decay factor (bb, the fraction that stays) and decay rate (rr, the fraction that leaves).

  • Practice reading exponential data tables to verify whether a ratio gives bb directly or whether a percentage change was described.

  • Solve the practice problems below to reinforce choosing the correct base multiplier in applied modeling.

OverviewACEpath Teacher's Diagnosis

02 The student computes the consecutive ratios inverted as A(t)/A(t+60), resulting in a growth factor greater than 1 rather than a decay factor.

Sample Student Work

Reviewed by ACEpath Teacher
Step-by-Step Review
Walk Through It with Your Teacher
Incorrect
  1. Step 1

    0.8400.504≈1.67\frac{0.840}{0.504} \approx 1.67, 0.5040.302≈1.67  ⟹  \frac{0.504}{0.302} \approx 1.67 \implies The ratio is approximately constant, confirming an exponential model.

    Correct

    A(60)A(0)=0.5040.840=0.600\frac{A(60)}{A(0)} = \frac{0.504}{0.840} = 0.600, A(120)A(60)=0.3020.504≈0.600\frac{A(120)}{A(60)} = \frac{0.302}{0.504} \approx 0.600

    You inverted the consecutive ratio. The multiplicative factor over forward time step Δt\Delta t must always be new valueold value=A(t+Δt)A(t)\frac{\text{new value}}{\text{old value}} = \frac{A(t+\Delta t)}{A(t)}. Inverting the terms gives A(t)A(t+Δt)≈1.67\frac{A(t)}{A(t+\Delta t)} \approx 1.67, which indicates growth rather than decay.

  2. Step 2

    b=1.67b = 1.67

    Correct

    b=0.600b = 0.600

    You carried forward your inverted ratio as the decay factor. Because absorbance decreases over time, the decay factor bb must be less than 11 (b=0.600b = 0.600).

  3. Step 3

    A(t)=0.840⋅(1.67)t/60A(t) = 0.840 \cdot (1.67)^{t/60}

    Correct

    A(t)=0.840⋅(0.600)t/60A(t) = 0.840 \cdot (0.600)^{t/60}

    You correctly identified the initial value a=0.840a = 0.840 and scaled the exponent by 6060, but the formula inherited the incorrect base b=1.67b = 1.67.

  4. Step 4

    A(180)=0.840⋅(1.67)3=0.840⋅4.66=3.91A(180) = 0.840 \cdot (1.67)^3 = 0.840 \cdot 4.66 = 3.91

    Correct

    A(180)=0.840⋅(0.600)180/60=0.840⋅(0.600)3=0.840⋅0.216≈0.181A(180) = 0.840 \cdot (0.600)^{180/60} = 0.840 \cdot (0.600)^3 = 0.840 \cdot 0.216 \approx 0.181

    You evaluated the function using sound arithmetic, but because the model had a growth factor, your calculated absorbance increased to 3.913.91 instead of decaying below 0.3020.302.

WHAT YOU DID WELL
Compliments from Your Teacher

You correctly identified that equal spacing in time with constant multiplicative ratios signals an exponential relationship.

You correctly identified the initial baseline absorbance a=A(0)=0.840a = A(0) = 0.840.

You set up the time scaling in the exponent as t60\frac{t}{60} to match the 60 s60\text{ s} measurement intervals.

THE ERROR
Where Your ACEpath Teacher Spotted the Mistake
Inverted ratio in exponential base

no

WHY IT HAPPENED
ACEpath Teacher's Diagnosis

You calculated the ratio as earlier value divided by later value rather than later value divided by earlier value, confusing the reciprocal scale factor with the forward time-step multiplier.

REASONING PATH
Your ACEpath teacher’s suggested approach
Ratio Direction Check
  • For any sequence where time increases from t1t_1 to t2t_2, the growth or decay multiplier is b=y(t2)y(t1)=laterearlierb = \frac{y(t_2)}{y(t_1)} = \frac{\text{later}}{\text{earlier}}.

  • Check whether the physical quantity is increasing or decreasing: decay requires 0<b<10 < b < 1, while growth requires b>1b > 1.

CORRECTED PATH
ACEpath Teacher's Demonstration
  1. Compute the forward ratio of successive outputs: A(60)A(0)=0.5040.840=0.600\frac{A(60)}{A(0)} = \frac{0.504}{0.840} = 0.600 and A(120)A(60)=0.3020.504≈0.600\frac{A(120)}{A(60)} = \frac{0.302}{0.504} \approx 0.600.

  2. Identify the initial value a=A(0)=0.840a = A(0) = 0.840 and the decay factor b=0.600b = 0.600.

  3. Write the exponential model with interval-scaled exponent: A(t)=0.840⋅(0.600)t/60A(t) = 0.840 \cdot (0.600)^{t/60}.

  4. Evaluate at t=180 st = 180\text{ s}: A(180)=0.840⋅(0.600)180/60=0.840⋅(0.600)3=0.840⋅0.216=0.18144A(180) = 0.840 \cdot (0.600)^{180/60} = 0.840 \cdot (0.600)^3 = 0.840 \cdot 0.216 = 0.18144.

Final answer

A(60)A(0)=0.600\frac{A(60)}{A(0)} = 0.600 and A(120)A(60)≈0.600\frac{A(120)}{A(60)} \approx 0.600, confirming exponential decay; b=0.600b = 0.600; A(t)=0.840⋅(0.600)t/60A(t) = 0.840 \cdot (0.600)^{t/60}; A(180)≈0.181A(180) \approx 0.181

NEXT STEPS
Final Takeaways from Your Teacher
  • Always write ylateryearlier\frac{y_{\text{later}}}{y_{\text{earlier}}} as a fraction before dividing so you do not accidentally invert the terms.

  • Perform a sanity check on your base: if the table values decrease as time increases, verify that your calculated bb satisfies 0<b<10 < b < 1.

OverviewACEpath Teacher's Diagnosis

03 The student forgets to scale the exponent by the 60-second time interval and writes t instead of t/60, calculating absorbance at t = 180 using 180 periods.

Sample Student Work

Reviewed by ACEpath Teacher
Step-by-Step Review
Walk Through It with Your Teacher
Partially correct
  1. Step 1

    A(60)A(0)=0.5040.840=0.60  ⟹  A(120)A(60)=0.3020.504≈0.60  ⟹  Constant ratio confirms exponential decay.\frac{A(60)}{A(0)} = \frac{0.504}{0.840} = 0.60 \implies \frac{A(120)}{A(60)} = \frac{0.302}{0.504} \approx 0.60 \implies \text{Constant ratio confirms exponential decay.}

  2. Step 2

    b=0.60b = 0.60

  3. Step 3

    A(t)=0.840⋅(0.60)tA(t) = 0.840 \cdot (0.60)^t

    Correct

    A(t)=0.840⋅(0.600)t/60A(t) = 0.840 \cdot (0.600)^{t/60}

    The factor b=0.600b = 0.600 applies every 60 s60\text{ s}, not every 1 s1\text{ s}. The exponent represents the number of 60 s60\text{ s} intervals elapsed, so it must be scaled as t60\frac{t}{60} as specified in the problem form A(t)=a⋅bt/60A(t) = a \cdot b^{t/60}.

  4. Step 4

    A(180)=0.840⋅(0.60)180≈0A(180) = 0.840 \cdot (0.60)^{180} \approx 0

    Correct

    A(180)=0.840⋅(0.600)180/60=0.840⋅(0.600)3≈0.181A(180) = 0.840 \cdot (0.600)^{180/60} = 0.840 \cdot (0.600)^3 \approx 0.181

    Because the model omitted the denominator of 6060 in the exponent, you evaluated (0.60)180(0.60)^{180} instead of (0.600)3(0.600)^3, leading to an incorrect predicted absorbance.

WHAT YOU DID WELL
Compliments from Your Teacher

You correctly tested the ratio of consecutive absorbance values to verify exponential decay.

You correctly identified the initial value a=0.840a = 0.840 and the decay factor b=0.600b = 0.600.

THE ERROR
Where Your ACEpath Teacher Spotted the Mistake
Omitted Time-Interval Scaling in Exponent

You wrote tt in the exponent instead of scaling it by the time interval Δt=60 s\Delta t = 60\text{ s}.

WHY IT HAPPENED
ACEpath Teacher's Diagnosis

Conflating the total elapsed time tt with the number of discrete decay periods tΔt\frac{t}{\Delta t}. When a multiplier applies over an interval of Δt\Delta t, the exponent counts how many such intervals have passed, requiring tΔt\frac{t}{\Delta t}.

REASONING PATH
Your ACEpath teacher’s suggested approach
Exponent as Period Count
  • In y=a⋅bt/Δty = a \cdot b^{t/\Delta t}, the exponent tΔt\frac{t}{\Delta t} counts the number of full intervals of length Δt\Delta t that have elapsed.

  • Check whether the data step Δt\Delta t equals 1 unit or multiple units; divide tt by Δt\Delta t whenever the period is longer than 1 unit.

CORRECTED PATH
ACEpath Teacher's Demonstration
  1. Substitute the initial value a=0.840a = 0.840 and decay factor b=0.600b = 0.600 into the required form A(t)=a⋅bt/60A(t) = a \cdot b^{t/60} to get A(t)=0.840⋅(0.600)t/60A(t) = 0.840 \cdot (0.600)^{t/60}.

  2. Substitute t=180 st = 180\text{ s} into the corrected function: A(180)=0.840⋅(0.600)180/60=0.840⋅(0.600)3A(180) = 0.840 \cdot (0.600)^{180/60} = 0.840 \cdot (0.600)^3.

  3. Compute (0.600)3=0.216(0.600)^3 = 0.216, then multiply: 0.840⋅0.216=0.18144≈0.1810.840 \cdot 0.216 = 0.18144 \approx 0.181.

Final answer

A(t)=0.840⋅(0.600)t/60A(t) = 0.840 \cdot (0.600)^{t/60}; A(180)≈0.181A(180) \approx 0.181

NEXT STEPS
Final Takeaways from Your Teacher
  • Always match the exponent denominator to the interval length Δt\Delta t between consecutive data points.

  • Test your equation with t=60 st = 60\text{ s} to confirm it outputs A(0)⋅b1A(0) \cdot b^1 before evaluating future values.

Lock it in

Similar question

01

A radioactive tracer has an initial mass of 120 mg120\text{ mg}. After 4 hours4\text{ hours}, 90 mg90\text{ mg} remains, and after 8 hours8\text{ hours}, 67.5 mg67.5\text{ mg} remains. Write the exponential decay function M(t)=a⋅bt/4M(t) = a \cdot b^{t/4} and find the mass remaining at t=12 hourst = 12\text{ hours}.

Answer

M(t)=120⋅(0.75)t/4M(t) = 120 \cdot (0.75)^{t/4}; at t=12 hourst = 12\text{ hours}, M(12)=120⋅(0.75)3=120⋅0.421875≈50.6 mgM(12) = 120 \cdot (0.75)^3 = 120 \cdot 0.421875 \approx 50.6\text{ mg}. Key steps: b=90120=0.75b = \frac{90}{120} = 0.75, a=120a = 120.

02

A drug's concentration in the bloodstream is measured every 30 minutes30\text{ minutes}: C(0)=50.0 mg/LC(0) = 50.0\text{ mg/L}, C(30)=35.0 mg/LC(30) = 35.0\text{ mg/L}, and C(60)=24.5 mg/LC(60) = 24.5\text{ mg/L}. Determine the decay factor bb per 30-minute30\text{-minute} period, state the percentage decay rate rr per period, and write C(t)C(t) in terms of minutes tt.

Answer

Decay factor b=0.70b = 0.70; decay rate r=30%r = 30\% (or 0.300.30); model C(t)=50.0⋅(0.70)t/30C(t) = 50.0 \cdot (0.70)^{t/30}. Key steps: ratio 35.050.0=0.70=b\frac{35.0}{50.0} = 0.70 = b, then r=1−b=0.30r = 1 - b = 0.30.

03

A cooling liquid has a temperature above room temperature given by data at 5-minute5\text{-minute} intervals: θ(0)=40.0∘C\theta(0) = 40.0^\circ\text{C} and θ(5)=32.0∘C\theta(5) = 32.0^\circ\text{C}. Assuming exponential decay θ(t)=a⋅bt/5\theta(t) = a \cdot b^{t/5}, determine how many minutes it will take for θ(t)\theta(t) to drop below 15.0∘C15.0^\circ\text{C}. Give your answer to the nearest minute.

Answer

t≈22 minutest \approx 22\text{ minutes}. Key steps: a=40.0a = 40.0, b=32.040.0=0.80b = \frac{32.0}{40.0} = 0.80; solve 40.0⋅(0.80)t/5=15.0  ⟹  (0.80)t/5=0.375  ⟹  t5=ln⁡(0.375)ln⁡(0.80)≈4.395  ⟹  t≈21.98≈22 min40.0 \cdot (0.80)^{t/5} = 15.0 \implies (0.80)^{t/5} = 0.375 \implies \frac{t}{5} = \frac{\ln(0.375)}{\ln(0.80)} \approx 4.395 \implies t \approx 21.98 \approx 22\text{ min}.

Loading workspace…