Resources

A high-precision cylindrical metal rod is machined to have a nominal diameter of d0=2.500 cmd_0 = 2.500\text{ cm}. Quality assurance protocols dictate that the absolute discrepancy between the measured diameter dd and nominal diameter d0d_0 must not exceed a tolerance of τ=150 μm\tau = 150\ \mu\text{m}. Express the acceptable range of diameter dd as an absolute-value inequality in millimeters (mm\text{mm}), and solve for the allowable interval of dd in millimeters.

Answer and steps

Final answer

Inequality: ∣d−25.000∣≤0.150 mm|d - 25.000| \le 0.150\text{ mm}; Allowable interval: [24.850 mm,25.150 mm][24.850\text{ mm}, 25.150\text{ mm}]

Steps

01

Convert all given quantities to millimeters (mm\text{mm})

To write the inequality in terms of millimeters, convert the nominal diameter d0d_0 and the tolerance τ\tau into mm\text{mm}:

  • Nominal diameter: d0=2.500 cm=2.500⋅10 mm=25.000 mmd_0 = 2.500\text{ cm} = 2.500 \cdot 10\text{ mm} = 25.000\text{ mm}
  • Tolerance: τ=150 μm=1501000 mm=0.150 mm\tau = 150\ \mu\text{m} = \frac{150}{1000}\text{ mm} = 0.150\text{ mm}

02

Formulate the absolute-value inequality

The discrepancy between the measured diameter dd and the nominal diameter d0d_0 is represented by the difference ∣d−d0∣|d - d_0|.

Quality assurance requires this discrepancy to be at most the tolerance τ\tau: ∣d−d0∣≤τ|d - d_0| \le \tau

Substituting the converted values gives: ∣d−25.000∣≤0.150|d - 25.000| \le 0.150


03

Solve the inequality for the allowable interval

Recall the standard rule for absolute-value inequalities: for any real number c>0c > 0, the inequality ∣x−a∣≤c|x - a| \le c is equivalent to the compound inequality: −c≤x−a≤c-c \le x - a \le c

Applying this rule to our inequality: −0.150≤d−25.000≤0.150-0.150 \le d - 25.000 \le 0.150

Add 25.00025.000 to all three parts of the inequality to isolate dd: 25.000−0.150≤d≤25.000+0.15025.000 - 0.150 \le d \le 25.000 + 0.150 24.850≤d≤25.15024.850 \le d \le 25.150

In interval notation, the allowable range for the diameter dd is: [24.850 mm,25.150 mm][24.850\text{ mm}, 25.150\text{ mm}]

Educational illustration for this question

Typical errors

OverviewACEpath Teacher's Diagnosis

01 The student incorrectly converts micrometers to millimeters by dividing by 100 instead of 1000, setting the tolerance as 1.5 mm.

Sample Student Work

Reviewed by ACEpath Teacher
Step-by-Step Review
Walk Through It with Your Teacher
Incorrect
  1. Step 1

    d_0 = 25 mm\text{ mm},  τ\tau = 150100\frac{150}{100} = 1.5 mm\text{ mm}

    Correct

    d_0 = 2.500 ×\times 10 = 25.000 mm\text{ mm},  τ\tau = 1501000\frac{150}{1000} = 0.150 mm\text{ mm}

    You correctly converted 2.500 cm2.500\text{ cm} to 25 mm25\text{ mm}, but divided by 100100 instead of 10001000 when converting micrometers to millimeters. Because 1 mm=1000 μm1\text{ mm} = 1000\ \mu\text{m}, 150 μm150\ \mu\text{m} equals 0.150 mm0.150\text{ mm}.

  2. Step 2

    |d - 25| ≤\le 1.5

    Correct

    |d - 25.000| ≤\le 0.150

    You correctly formulated the tolerance condition as ∣d−d0∣≤τ|d - d_0| \le \tau, but the inequality inherited your earlier conversion error of τ=1.5 mm\tau = 1.5\text{ mm}.

  3. Step 3

    -1.5 ≤\le d - 25 ≤\le 1.5   ⟹  \implies 23.5 ≤\le d ≤\le 26.5 mm\text{ mm}

    Correct

    -0.150 ≤\le d - 25.000 ≤\le 0.150   ⟹  \implies 24.850 ≤\le d ≤\le 25.150 mm\text{ mm}

    Your algebraic method for splitting and solving the absolute-value inequality was completely sound, but it propagated the incorrect tolerance value.

WHAT YOU DID WELL
Compliments from Your Teacher

You correctly converted the nominal diameter from centimeters to millimeters.

You correctly structured the tolerance condition using the absolute-value difference ∣d−d0∣≤τ|d - d_0| \le \tau.

You correctly unpacked the absolute-value inequality into a three-part compound inequality and solved for dd.

THE ERROR
Where Your ACEpath Teacher Spotted the Mistake
Metric prefix conversion error

You divided 150 μm150\ \mu\text{m} by 100100 instead of 10001000 when converting to millimeters, making the tolerance ten times larger than specified.

WHY IT HAPPENED
ACEpath Teacher's Diagnosis

Confusing the metric prefix micro- (10−6 m10^{-6}\text{ m}, or 10−3 mm10^{-3}\text{ mm}) with centi- (10−210^{-2}) or mistaking the step between millimeter and micrometer as a factor of 100100 rather than 10001000.

REASONING PATH
Your ACEpath teacher’s suggested approach
Verify Metric Prefix Steps
  • 1 mm\text{ mm} = 10^{-3}\text{ m}$$\text{ and } 1\ \mu$$\text{m} = 10^{-6} m\text{ m}   ⟹  \implies 1 mm\text{ mm} = 1000\ $\mum\text{m}

  • To convert micrometers (μm\mu\text{m}) to millimeters (mm\text{mm}), always divide by 10001000 (or multiply by 10−310^{-3}).

Physical Reality Check
  • High-precision machining tolerances are typically a small fraction of a millimeter.

  • A tolerance of 1.5 mm1.5\text{ mm} on a 25 mm25\text{ mm} rod is 6%6\%, which is far too coarse for precision machining; 0.15 mm0.15\text{ mm} fits the expected scale.

CORRECTED PATH
ACEpath Teacher's Demonstration
  1. Convert the tolerance using the correct scale factor: τ=150 μm1000 μm/mm=0.150 mm\tau = \frac{150\ \mu\text{m}}{1000\ \mu\text{m/mm}} = 0.150\text{ mm}.

  2. Substitute into the absolute-value condition: ∣d−25.000∣≤0.150 mm|d - 25.000| \le 0.150\text{ mm}.

  3. Expand the absolute-value inequality: −0.150≤d−25.000≤0.150-0.150 \le d - 25.000 \le 0.150.

  4. Add 25.00025.000 to all parts: 24.850 mm≤d≤25.150 mm24.850\text{ mm} \le d \le 25.150\text{ mm}.

Final answer

Inequality: ∣d−25.000∣≤0.150 mm|d - 25.000| \le 0.150\text{ mm}; Allowable interval: [24.850 mm,25.150 mm][24.850\text{ mm}, 25.150\text{ mm}]

NEXT STEPS
Final Takeaways from Your Teacher
  • Review standard SI prefixes from milli- (10−310^{-3}) to micro- (10−610^{-6}) and nano- (10−910^{-9}).

  • Practice converting tolerance specifications between μm\mu\text{m}, mm\text{mm}, and cm\text{cm} before substituting them into inequalities.

OverviewACEpath Teacher's Diagnosis

02 The student misinterprets 'must not exceed' as a strict inequality rather than non-strict.

Sample Student Work

Reviewed by ACEpath Teacher
Step-by-Step Review
Walk Through It with Your Teacher
Partially correct
  1. Step 1

    d_0 = 25 mm\text{ mm}   ⟹  \implies τ\tau = 0.15 mm\text{ mm}

  2. Step 2

    |d - 25| < 0.15

    Correct

    |d - 25.000| ≤\le 0.150

    The condition 'must not exceed' allows the discrepancy to equal the tolerance τ\tau, which requires a non-strict inequality (≤\le) rather than a strict inequality (<<).

  3. Step 3

    -0.15 < d - 25 < 0.15   ⟹  \implies 24.85 < d < 25.15 mm\text{ mm}

    Correct

    -0.150 ≤\le d - 25.000 ≤\le 0.150   ⟹  \implies 24.850 mm\text{ mm} ≤\le d ≤\le 25.150\text{ mm}$$\text{ (or }[24.850 mm\text{ mm}, 25.150 mm\text{ mm}])$$

    Your algebraic method of expanding the absolute value and isolating dd was completely sound, but the final interval inherited the strict inequality signs from Step 2.

WHAT YOU DID WELL
Compliments from Your Teacher

You correctly converted the given units into millimeters.

You set up the discrepancy difference ∣d−d0∣|d - d_0| appropriately.

You applied the correct algebraic rule to split and solve a centered absolute-value inequality.

THE ERROR
Where Your ACEpath Teacher Spotted the Mistake
Strict vs. Non-Strict Inequality

You wrote << instead of ≤\le when translating the phrase 'must not exceed'.

WHY IT HAPPENED
ACEpath Teacher's Diagnosis

Associating 'exceed' solely with strict inequalities without recognizing that 'not exceeding' means being less than or equal to the threshold (x≤cx \le c).

REASONING PATH
Your ACEpath teacher’s suggested approach
Translating Tolerance Keywords
  • 'Must not exceed cc' and 'at most cc' mean ≤c\le c, whereas 'strictly less than cc' means <c< c.

  • Whenever you encounter phrases like 'within tolerance' or 'must not exceed', use non-strict inequalities (≤\le).

CORRECTED PATH
ACEpath Teacher's Demonstration
  1. Set up the absolute discrepancy with a non-strict inequality: ∣d−25.000∣≤0.150|d - 25.000| \le 0.150.

  2. Unfold into a three-part compound inequality: −0.150≤d−25.000≤0.150-0.150 \le d - 25.000 \le 0.150.

  3. Add 25.00025.000 to all parts to find the allowable range: 24.850 mm≤d≤25.150 mm24.850\text{ mm} \le d \le 25.150\text{ mm}, or [24.850 mm,25.150 mm][24.850\text{ mm}, 25.150\text{ mm}].

Final answer

Inequality: ∣d−25.000∣≤0.150 mm|d - 25.000| \le 0.150\text{ mm}; Allowable interval: [24.850 mm,25.150 mm][24.850\text{ mm}, 25.150\text{ mm}]

NEXT STEPS
Final Takeaways from Your Teacher
  • Review English comparison phrases that correspond to ≤\le versus <<, such as 'does not exceed' vs. 'is less than'.

  • Practice expressing allowable engineering intervals using closed brackets [a,b][a, b] when boundary values satisfy the specification.

OverviewACEpath Teacher's Diagnosis

03 The student subtracts the tolerance from the nominal value on the right side instead of adding it, finding an incorrect upper bound.

Sample Student Work

Reviewed by ACEpath Teacher
Step-by-Step Review
Walk Through It with Your Teacher
Incorrect
  1. Step 1

    d0=25 mm  ⟹  τ=0.15 mmd_0 = 25\text{ mm} \implies \tau = 0.15\text{ mm}

  2. Step 2

    ∣d−25∣≤0.15|d - 25| \le 0.15

  3. Step 3

    −0.15≤d−25≤0.15-0.15 \le d - 25 \le 0.15

  4. Step 4

    25−0.15≤d≤25−0.1525 - 0.15 \le d \le 25 - 0.15

    Correct

    25.000−0.150≤d≤25.000+0.15025.000 - 0.150 \le d \le 25.000 + 0.150

    To isolate dd, you must add 2525 to all three sections of the inequality. On the right-hand side, adding 2525 to 0.150.15 yields 25+0.1525 + 0.15, not 25−0.1525 - 0.15.

  5. Step 5

    24.85≤d≤24.85 mm24.85 \le d \le 24.85\text{ mm}

    Correct

    24.850 mm≤d≤25.150 mm24.850\text{ mm} \le d \le 25.150\text{ mm}, or [24.850 mm,25.150 mm][24.850\text{ mm}, 25.150\text{ mm}]

    Because of the sign error in the previous step, your upper bound evaluated to 24.85 mm24.85\text{ mm} instead of 25.15 mm25.15\text{ mm}.

WHAT YOU DID WELL
Compliments from Your Teacher

You converted both measurements into consistent millimeter units correctly.

You translated the allowable discrepancy condition into a proper absolute-value inequality.

You correctly rewrote ∣x−a∣≤c|x - a| \le c into the bounded double inequality −c≤x−a≤c-c \le x - a \le c.

THE ERROR
Where Your ACEpath Teacher Spotted the Mistake
Compound inequality balance error

You wrote a subtraction sign instead of an addition sign on the right-hand side when adding 25 to eliminate -25.

WHY IT HAPPENED
ACEpath Teacher's Diagnosis

Losing track of uniform inverse operations across compound inequalities, mistakenly mirroring the left-side expression (nominal minus tolerance) on the right side.

REASONING PATH
Your ACEpath teacher’s suggested approach
Uniform addition across compound inequalities
  • When solving −c≤d−a≤c-c \le d - a \le c, isolate dd by performing the exact same operation on all three parts: add aa to every part.

  • Write out (a)+(−c)≤d≤(a)+c(a) + (-c) \le d \le (a) + c, ensuring the right side is explicitly an addition: a+ca + c.

Tolerance reality check
  • A tolerance interval must span symmetrically around the target nominal value: [nominal−τ, nominal+τ][\text{nominal} - \tau,\ \text{nominal} + \tau].

  • Always verify that your lower bound is less than the nominal value and your upper bound is greater than the nominal value.

CORRECTED PATH
ACEpath Teacher's Demonstration
  1. Add 25.00025.000 to each part of −0.150≤d−25.000≤0.150-0.150 \le d - 25.000 \le 0.150:

  2. 25.000−0.150≤d≤25.000+0.15025.000 - 0.150 \le d \le 25.000 + 0.150

  3. Compute both bounds: 24.850≤d≤25.15024.850 \le d \le 25.150.

Final answer

[24.850 mm,25.150 mm][24.850\text{ mm}, 25.150\text{ mm}] (or 24.850 mm≤d≤25.150 mm24.850\text{ mm} \le d \le 25.150\text{ mm})

NEXT STEPS
Final Takeaways from Your Teacher
  • Review how inverse operations apply uniformly to all three parts of a double inequality.

  • Practice checking that tolerance intervals are centered around the nominal target value.

  • Work through the flashcards and practice problems below to master solving symmetric tolerance intervals.

Lock it in

Similar question

01

A steel bearing has a nominal radius of r0=12.00 mmr_0 = 12.00\text{ mm} with an allowable error of at most 80 μm80\ \mu\text{m}. Express the condition as an absolute-value inequality in millimeters and find the interval of acceptable radii.

Answer

∣r−12.000∣≤0.080 mm|r - 12.000| \le 0.080\text{ mm}; Interval: [11.920 mm,12.080 mm][11.920\text{ mm}, 12.080\text{ mm}]. Key step: τ=80 μm=801000 mm=0.080 mm\tau = 80\ \mu\text{m} = \frac{80}{1000}\text{ mm} = 0.080\text{ mm}.

02

An optical fiber core has a target diameter of D0=0.125 cmD_0 = 0.125\text{ cm}. The manufacturing specification requires ∣D−D0∣≤45 μm|D - D_0| \le 45\ \mu\text{m}. Write the inequality in millimeters and solve for the allowable range of diameter DD in millimeters.

Answer

∣D−1.250∣≤0.045 mm|D - 1.250| \le 0.045\text{ mm}; Interval: [1.205 mm,1.295 mm][1.205\text{ mm}, 1.295\text{ mm}]. Key steps: D0=0.125 cm=1.250 mmD_0 = 0.125\text{ cm} = 1.250\text{ mm}, and τ=45 μm=0.045 mm\tau = 45\ \mu\text{m} = 0.045\text{ mm}.

03

A microchip track width ww must satisfy ∣2w−1.600 mm∣≤600 μm|2w - 1.600\text{ mm}| \le 600\ \mu\text{m}. Express the tolerance in millimeters, rewrite the inequality in the form ∣w−w0∣≤τ|w - w_0| \le \tau, and find the interval of acceptable width ww in millimeters.

Answer

∣w−0.800∣≤0.300 mm|w - 0.800| \le 0.300\text{ mm}; Interval: [0.500 mm,1.100 mm][0.500\text{ mm}, 1.100\text{ mm}]. Key steps: 600 μm=0.600 mm600\ \mu\text{m} = 0.600\text{ mm}. Divide the entire inequality ∣2(w−0.800)∣≤0.600|2(w - 0.800)| \le 0.600 by 22 to get ∣w−0.800∣≤0.300|w - 0.800| \le 0.300.

Loading workspace…