Resources
In a physics laboratory report on simple harmonic motion, a student measures the period of a simple pendulum of length released from rest at an initial angular displacement of (). Using the small-angle linearization model with , the student predicts . (a) State the coordinate and mathematical approximation underlying this model equation. (b) Using the second-order Taylor expansion correction , calculate the accurate period and the sign of the error defined as . (c) Explain why this negative error trap arises mathematically from replacing the restoring torque with its linear approximation.
Answer and steps
Final answer
(a) The equation of motion is linearized using the small-angle approximation (in radians), which assumes . (b) ; error (negative sign indicates the linear model systematically underestimates the true period). (c) Because for all , the linearized model overestimates the true restoring force magnitude (); an artificially stiffer restoring force causes the predicted oscillator to cycle faster, erroneously truncating the modeled period.
Steps
(a) Model Assumptions and Approximations
The exact equation of motion for an ideal simple pendulum of length swinging in a vertical plane under gravity is:
where represents the angular displacement from the vertical measured in radians.
To obtain the standard simple harmonic motion formula , the nonlinear restoring term is expanded as a Maclaurin series:
The model relies on the small-angle approximation:
This approximation assumes that higher-order terms—predominantly the cubic term —are negligibly small, which only holds when .
(b) Calculation of the Corrected Period and Error
Given:
- Initial amplitude:
- Linearized period:
Using the second-order Taylor correction for the period:
- Compute the correction factor:
- Calculate :
- Determine the error :
The error has a negative sign, indicating that the small-angle linear model systematically underestimates the true period of oscillation.
(c) Mathematical and Physical Reason for the Negative Error
The true restoring torque acting on the pendulum bob is proportional to , while the linearized model assumes a restoring torque proportional to .
- For any displacement , the series expansion shows:
- Consequently, the linear approximation overestimates the magnitude of the restoring force:
Because the model assumes a restoring force that is stronger ("stiffer") than the actual force at every non-zero angle, it predicts that the pendulum accelerates back to the equilibrium position faster than it actually does. This artificially accelerates each cycle, causing the model to yield a shorter period () and resulting in a negative prediction error ().
Typical errors
01 The student substitutes the amplitude in degrees rather than radians into the Taylor expansion correction formula, producing an unrealistically large period.
Sample Student Work
Reviewed by ACEpath TeacherStep-by-Step Review
Walk Through It with Your Teacher- Step 1
Angular coordinate from vertical Approximation:
- Step 2Correct
Taylor series expansions for trigonometric functions and derived correction formulas are defined exclusively for angles in radians. Substituting treats the angular amplitude as rather than .
- Step 3
, negative
Correct, negative
Your subtraction step and identification of the negative sign were logically applied to your previous number, but the numerical magnitude was affected by the degree substitution error in the previous step.
- Step 4
Since , the true restoring force is weaker than the linearized force. This makes the pendulum slower and the true period longer, so is negative.
WHAT YOU DID WELL
Compliments from Your TeacherYou correctly stated the angular coordinate and the small-angle approximation .
You accurately reasoned that makes the true restoring force weaker and the true period longer.
You correctly defined and calculated the error difference formula and identified its sign.
THE ERROR
Where Your ACEpath Teacher Spotted the MistakeIn part (b), you wrote directly inside the bracketed correction factor instead of using the provided radian value .
WHY IT HAPPENED
ACEpath Teacher's DiagnosisTaylor series expansions and analytical approximations of trigonometric functions derive directly from calculus limits where , which is valid only when is expressed in dimensionless radians.
REASONING PATH
Your ACEpath teacher’s suggested approach- Calculus and Series Angle Requirement
Any series expansion, derivative, or power-series correction formula involving angle variables requires the angle to be in radians.
Always verify that angular quantities are converted to radians before squaring or inserting into Taylor series correction terms.
- Order of Magnitude Reality Check
A second-order correction term for a moderate angle should adjust the period by only a few percent (typically ).
If a correction factor yields an increase of over (such as ), stop and check if an angle was entered in degrees.
CORRECTED PATH
ACEpath Teacher's DemonstrationConvert the angle to radians or use the given value: .
Compute the second-order correction factor: .
Calculate the corrected period: .
Compute the prediction error: .
, with error (negative sign).
02 The student forgets to square the initial angle θ_0 in the correction factor, underestimating the second-order period increase.
Sample Student Work
Reviewed by ACEpath TeacherStep-by-Step Review
Walk Through It with Your Teacher- Step 1
Angular coordinate measured from downward vertical Approximation is
- Step 2Correct
You substituted linearly instead of squaring it as required by the formula term .
- Step 3
, negative
Correct, negative
Your subtraction and sign identification are logically sound, but the numerical result is affected by using instead of .
- Step 4
Because , the true restoring torque is smaller than the model torque. A smaller restoring torque causes a slower return and longer period, yielding .
WHAT YOU DID WELL
Compliments from Your TeacherYou correctly identified the small-angle approximation .
You accurately reasoned that leads to a smaller true restoring torque, a longer actual period, and a negative error .
THE ERROR
Where Your ACEpath Teacher Spotted the MistakeYou substituted as a linear factor rather than evaluating in .
WHY IT HAPPENED
ACEpath Teacher's DiagnosisOverlooking powers of dimensionless parameters in perturbation and Taylor series corrections, often caused by treating correction terms as simple percentage scalers.
REASONING PATH
Your ACEpath teacher’s suggested approach- Check the Order of the Expansion Term
Perturbation corrections in symmetric systems often depend on even powers (like ), not linear terms.
Always circle exponents in series approximations before plugging in numerical values.
- Dimensionless Quantity Check
In , the term represents a fractional correction and must match the formula's degree exactly.
Compute as a distinct intermediate value before dividing by .
CORRECTED PATH
ACEpath Teacher's DemonstrationCompute the square of the initial amplitude:
Calculate the fractional correction:
Evaluate the true period:
Compute the modeling error:
and (negative)
03 The student reverses the sign of the error or claims the model overestimates the period because sin(θ) < θ is incorrectly interpreted as meaning the true period must be smaller.
Sample Student Work
Reviewed by ACEpath TeacherStep-by-Step Review
Walk Through It with Your Teacher- Step 1
Coordinate from downward vertical ⟹ Mathematical approximation:
- Step 2
- Step 3
, positive
Correct, negative
You reversed the subtraction order. The question explicitly defined the error as , which gives , indicating a negative error.
- Step 4
Replacing with the larger value overestimates the restoring torque. The student computes as , giving a positive error.
CorrectSince for , the linear model overestimates the magnitude of the restoring torque (). An artificially stronger restoring force causes the modeled pendulum to accelerate faster, resulting in a shorter modeled period () and a negative error .
You correctly noted that replacing with overestimates the restoring torque, but you did not link that stiffer restoring torque to a faster cycle () causing a negative error.
WHAT YOU DID WELL
Compliments from Your TeacherYou clearly identified the downward vertical reference coordinate and the linearization .
You correctly substituted the amplitude in radians into the second-order period correction formula to obtain .
THE ERROR
Where Your ACEpath Teacher Spotted the MistakeYou computed the difference as rather than following the prompt's defined order .
WHY IT HAPPENED
ACEpath Teacher's DiagnosisYou treated modeling error as an unsigned or arbitrarily ordered difference, overlooking that the standard definition of prediction error is . This prevented you from recognizing that an overestimated restoring torque accelerates the modeled oscillation, making and therefore creating a negative error.
REASONING PATH
Your ACEpath teacher’s suggested approach- Check the Error Definition
Modeling error is defined by the prompt (usually ).
Always substitute the values in the exact order specified: .
- Connect Restoring Force to Period
Period scales inversely with the square root of the restoring stiffness ().
When a linearization overestimates restoring torque (), the model predicts faster return to center, meaning .
CORRECTED PATH
ACEpath Teacher's DemonstrationApply the given definition: .
State the sign: The error is negative, showing the small-angle model underestimates the real period.
Complete the physical reasoning: Because for , the linear model assumes a stronger restoring force than reality, driving the oscillator back to equilibrium faster and yielding a shorter modeled period ().
(b) ; (negative). (c) The linear approximation overestimates the restoring torque (), making the modeled oscillator artificially stiffer and faster, which leads to and thus a negative prediction error.
Lock it in
Why must angular displacements always be expressed in radians when evaluating Taylor series approximations such as or ?
Radian measure is dimensionless and satisfies ; degree formulas require extra scaling factors of that invalidate standard calculus identities.
Similar question
A simple pendulum with linearized period is released from an angle of . Using , calculate the accurate period and the modeling error .
Answer
Convert . The correction is . Thus, . The modeling error is .
In a physical pendulum experiment, an engineer estimates the restoring torque using the small-angle model . If the true restoring torque is , find the percentage error at an operating angle of .
Answer
At , . The relative error is . The linear model overestimates the restoring torque magnitude by approximately .
The finite-amplitude period of a pendulum can be approximated to fourth order as . For an amplitude of () and , calculate the second-order correction term, the fourth-order correction term, and the resulting period .
Answer
With : the second-order term is (); the fourth-order term is (). The total factor is , yielding .