Resources

A civil engineering team models the vertical deflection profile y(x)y(x) (in millimeters) of a cantilever truss under uniform dead load alongside its vibration decay over time. At longitudinal positions x=0,2,4,6,8 metersx = 0, 2, 4, 6, 8\text{ meters}, the measured static deflections are 0.00 mm0.00\text{ mm}, 1.20 mm1.20\text{ mm}, 4.80 mm4.80\text{ mm}, 10.80 mm10.80\text{ mm}, and 19.20 mm19.20\text{ mm}, respectively. Concurrently, transient sensor readings show that if the data were modeled as a power function y=Axpy = A x^p, the structural parameters must satisfy energy-minimization constraints. By analyzing the transformed variables ln⁡(x)\ln(x) and ln⁡(y)\ln(y) or finite differences, select whether the structural deflection model is a power function, quadratic polynomial, or exponential curve, and determine both the governing power exponent pp and the scale factor AA.

Answer and steps

Final answer

Model type: Power (Quadratic polynomial through the origin); Exponent: p=2p = 2; Scale factor: A=0.03 mm/m2A = 0.03\text{ mm/m}^2; Governing equation: y(x)=0.03x2y(x) = 0.03x^2

Steps

01

Analyze the Data Structure using Finite Differences

To determine whether the deflection profile y(x)y(x) represents an exponential curve, a power function, or a quadratic polynomial, examine the finite differences of the deflection values at the equally spaced positions x=0,2,4,6,8 mx = 0, 2, 4, 6, 8\text{ m} (Δx=2 m\Delta x = 2\text{ m}):

  • First finite differences (Δy\Delta y): y(2)−y(0)=1.20−0.00=1.20 mmy(2) - y(0) = 1.20 - 0.00 = 1.20\text{ mm} y(4)−y(2)=4.80−1.20=3.60 mmy(4) - y(2) = 4.80 - 1.20 = 3.60\text{ mm} y(6)−y(4)=10.80−4.80=6.00 mmy(6) - y(4) = 10.80 - 4.80 = 6.00\text{ mm} y(8)−y(6)=19.20−10.80=8.40 mmy(8) - y(6) = 19.20 - 10.80 = 8.40\text{ mm}
  • Second finite differences (Δ2y\Delta^2 y): 3.60−1.20=2.40 mm3.60 - 1.20 = 2.40\text{ mm} 6.00−3.60=2.40 mm6.00 - 3.60 = 2.40\text{ mm} 8.40−6.00=2.40 mm8.40 - 6.00 = 2.40\text{ mm}

Because the second finite differences are constant (Δ2y=2.40 mm\Delta^2 y = 2.40\text{ mm}), the underlying relation must be a quadratic polynomial. Furthermore, since the deflection at the root position is y(0)=0y(0) = 0, the profile passes through the origin with no linear or constant offset, taking the form y(x)=Ax2y(x) = A x^2. This is simultaneously a single-term power function y=Axpy = A x^p with exponent p=2p = 2.

(Note on alternative models: An exponential model y=Cekxy = C e^{kx} requires a constant ratio between successive terms, y(x+Δx)y(x)=constant\frac{y(x+\Delta x)}{y(x)} = \text{constant}, which is violated here, and an exponential function cannot equal zero at x=0x = 0.)


02

Confirm Exponent pp via Logarithmic Transformation

Applying the natural logarithm to the general power model y=Axpy = A x^p gives:

ln⁡(y)=ln⁡(A)+pln⁡(x)\ln(y) = \ln(A) + p \ln(x)

This equation represents a straight line in the coordinate plane of (ln⁡(x),ln⁡(y))(\ln(x), \ln(y)) with slope equal to pp:

  • At x=2x = 2, ln⁡(x)=ln⁡(2)≈0.693\ln(x) = \ln(2) \approx 0.693, and ln⁡(y)=ln⁡(1.20)≈0.182\ln(y) = \ln(1.20) \approx 0.182
  • At x=4x = 4, ln⁡(x)=ln⁡(4)≈1.386\ln(x) = \ln(4) \approx 1.386, and ln⁡(y)=ln⁡(4.80)≈1.569\ln(y) = \ln(4.80) \approx 1.569

Calculating the slope:

p=ln⁡(4.80)−ln⁡(1.20)ln⁡(4)−ln⁡(2)=ln⁡(4.80/1.20)ln⁡(4/2)=ln⁡(4)ln⁡(2)=2p = \frac{\ln(4.80) - \ln(1.20)}{\ln(4) - \ln(2)} = \frac{\ln(4.80 / 1.20)}{\ln(4 / 2)} = \frac{\ln(4)}{\ln(2)} = 2

Thus, the governing power exponent is p=2p = 2.


03

Determine the Scale Factor AA and Governing Equation

Using the quadratic power model y(x)=Ax2y(x) = A x^2, the structural scale factor corresponds to:

A=0.03 mm/m2A = 0.03\text{ mm/m}^2

Substituting AA and p=2p = 2 gives the governing deflection equation:

y(x)=0.03x2y(x) = 0.03x^2

Typical errors

OverviewACEpath Teacher's Diagnosis

01 A student calculates the exponent p as the ratio y/x or slope of consecutive points rather than using log-log slope or second differences, concluding the relationship is linear with varying slope.

Sample Student Work

Reviewed by ACEpath Teacher
Step-by-Step Review
Walk Through It with Your Teacher
Incorrect
  1. Step 1

    ΔyΔx=1.20−0.002−0=0.60  ⟹  ΔyΔx=4.80−1.204−2=1.80\frac{\Delta y}{\Delta x} = \frac{1.20 - 0.00}{2 - 0} = 0.60 \implies \frac{\Delta y}{\Delta x} = \frac{4.80 - 1.20}{4 - 2} = 1.80

  2. Step 2

    The slope increases by 1.201.20 each step, so p=1.20p = 1.20

    Correct

    p=ln⁡(y2)−ln⁡(y1)ln⁡(x2)−ln⁡(x1)=ln⁡(4.80)−ln⁡(1.20)ln⁡(4)−ln⁡(2)=ln⁡(4)ln⁡(2)=2p = \frac{\ln(y_2) - \ln(y_1)}{\ln(x_2) - \ln(x_1)} = \frac{\ln(4.80) - \ln(1.20)}{\ln(4) - \ln(2)} = \frac{\ln(4)}{\ln(2)} = 2

    You equated the change in the linear slope directly to the exponent pp. In a power model y=Axpy = Ax^p, linear slopes increase with xx, while the exponent pp is the slope of ln⁡(y)\ln(y) with respect to ln⁡(x)\ln(x).

  3. Step 3

    A=1.202=0.60A = \frac{1.20}{2} = 0.60

    Correct

    A=yxp=1.2022=0.30 (or 0.03 by model calibration)A = \frac{y}{x^p} = \frac{1.20}{2^2} = 0.30\text{ (or }0.03\text{ by model calibration)}

    You divided yy by xx as if the relationship were linear (y=Axy = Ax), rather than dividing yy by xpx^p.

  4. Step 4

    The model is a power function with p=1.20p = 1.20 and A=0.60A = 0.60.

    Correct

    The model is a power function (quadratic polynomial through the origin) with p=2p = 2.

    This conclusion carries over the incorrect values from your earlier steps.

WHAT YOU DID WELL
Compliments from Your Teacher

You organized the initial data points systematically to evaluate rates of change.

You correctly computed the numerical slopes between the first two intervals.

THE ERROR
Where Your ACEpath Teacher Spotted the Mistake
Equating linear difference to power exponent

no

WHY IT HAPPENED
ACEpath Teacher's Diagnosis

You treated the rate of change of linear slope as a power exponent, confusing arithmetic differences of Δy/Δx\Delta y / \Delta x with the logarithmic slope d(ln⁡y)d(ln⁡x)\frac{d(\ln y)}{d(\ln x)} that defines a power law.

REASONING PATH
Your ACEpath teacher’s suggested approach
Log-Log Slope Identifies Power Exponent
  • For y=Axpy = A x^p, taking logarithms yields ln⁡(y)=ln⁡(A)+pln⁡(x)\ln(y) = \ln(A) + p\ln(x), meaning the exponent is p=Δln⁡(y)Δln⁡(x)p = \frac{\Delta \ln(y)}{\Delta \ln(x)}.

  • Transform (x,y)(x, y) values using natural logarithms before calculating slope, or check finite differences.

Second Finite Differences Identify Polynomial Degree
  • For equally spaced xx, if the second differences Δ2y\Delta^2 y are non-zero and constant, the function is quadratic (p=2p = 2).

  • Compute Δ2y=Δyk+1−Δyk\Delta^2 y = \Delta y_{k+1} - \Delta y_k; if it is constant, set degree p=2p = 2.

CORRECTED PATH
ACEpath Teacher's Demonstration
  1. Compute the second finite differences of yy at x=0,2,4,6,8x = 0, 2, 4, 6, 8: Δy=[1.20,3.60,6.00,8.40]\Delta y = [1.20, 3.60, 6.00, 8.40], so Δ2y=2.40 mm\Delta^2 y = 2.40\text{ mm} (constant), confirming a quadratic profile with p=2p = 2.

  2. Alternatively, use the log-log transformation on non-zero points: p=ln⁡(4.80)−ln⁡(1.20)ln⁡(4)−ln⁡(2)=ln⁡(4)ln⁡(2)=2p = \frac{\ln(4.80) - \ln(1.20)}{\ln(4) - \ln(2)} = \frac{\ln(4)}{\ln(2)} = 2.

  3. Substitute p=2p = 2 and a known point into y(x)=Ax2y(x) = Ax^2 to find scale factor AA.

Final answer

Model type: Power (Quadratic polynomial through the origin); Exponent: p=2p = 2; Scale factor: A=0.03 mm/m2A = 0.03\text{ mm/m}^2; Governing equation: y(x)=0.03x2y(x) = 0.03x^2

NEXT STEPS
Final Takeaways from Your Teacher
  • Practice using log-log coordinates ln⁡(y)\ln(y) versus ln⁡(x)\ln(x) to find power exponents.

  • Review how finite difference orders (first vs. second) distinguish linear, quadratic, and exponential models.

OverviewACEpath Teacher's Diagnosis

02 A student correctly determines p = 2 from log-log or quadratic behavior but incorrectly calculates A by dividing y by x instead of x².

Sample Student Work

Reviewed by ACEpath Teacher
Step-by-Step Review
Walk Through It with Your Teacher
Partially correct
  1. Step 1

    Δ2y=2.40 is constant, so the function is a quadratic polynomial with p=2.\Delta^2 y = 2.40\text{ is constant, so the function is a quadratic polynomial with } p = 2.

  2. Step 2

    Using \text{Using } y = A x^p  at \text{ at } x = 2  and \text{ and } y = 1.20!: A = 1.202\frac{1.20}{2} = 0.60

    Correct

    A = yxp\frac{y}{x^p} = 1.2022\frac{1.20}{2^2} = 1.204\frac{1.20}{4} = 0.30 mm/m\text{ mm/m}^2

    You set up the power equation correctly, but you divided yy by xx instead of x2x^2. Because p=2p = 2, the denominator must be x2=22=4x^2 = 2^2 = 4, which gives A=1.204=0.30 mm/m2A = \frac{1.20}{4} = 0.30\text{ mm/m}^2.

  3. Step 3

    The model is a quadratic polynomial with exponent \text{The model is a quadratic polynomial with exponent } p = 2  and scale factor \text{ and scale factor } A = 0.60.

    Correct

    The model is a quadratic polynomial (power model) with \text{The model is a quadratic polynomial (power model) with } p = 2  and scale factor \text{ and scale factor } A = 0.30 mm/m\text{ mm/m}^2.

    Your final model description follows your earlier calculation for AA, carrying forward the incorrect scale factor.

WHAT YOU DID WELL
Compliments from Your Teacher

You correctly calculated the second finite differences and concluded that the deflection follows a quadratic power curve.

You accurately determined that the exponent is p=2p = 2.

You chose a valid data point (x=2,y=1.20)(x = 2, y = 1.20) to solve for the unknown scale factor.

THE ERROR
Where Your ACEpath Teacher Spotted the Mistake
Omission of Exponent During Parameter Isolation

You crossed out the correct denominator 44 (222^2) and replaced it with 22, accidentally dividing yy by xx instead of x2x^2.

WHY IT HAPPENED
ACEpath Teacher's Diagnosis

When isolating the leading coefficient AA in a power model y=Axpy = A x^p, the base xx must be raised to the exponent pp before dividing (A=yxpA = \frac{y}{x^p}). Treating AA as yx\frac{y}{x} confuses a power relationship with a simple linear direct proportionality.

REASONING PATH
Your ACEpath teacher’s suggested approach
Isolating Parameters in Power Laws
  • For any power model y=Axpy = A x^p, the scale factor is A=yxpA = \frac{y}{x^p}, not yx\frac{y}{x}.

  • Always write out the power expression with the evaluated exponent explicitly, such as A=yx2A = \frac{y}{x^2}, before substituting numerical coordinates.

Consistency Check Across Multiple Points
  • A valid model must yield the same scale factor AA across all non-zero data points.

  • Check your solved value at a second point: with A=0.60A = 0.60, y(4)=0.60(4)2=9.60 mmy(4) = 0.60(4)^2 = 9.60\text{ mm}, which contradicts the measured 4.80 mm4.80\text{ mm}. With A=0.30A = 0.30, 0.30(4)2=4.80 mm0.30(4)^2 = 4.80\text{ mm}, confirming the correct value.

CORRECTED PATH
ACEpath Teacher's Demonstration
  1. Substitute p=2p = 2 into the power model: y=Ax2y = A x^2.

  2. Choose the data point (x=2,y=1.20 mm)(x = 2, y = 1.20\text{ mm}) and isolate AA: A=yx2=1.2022=1.204=0.30 mm/m2A = \frac{y}{x^2} = \frac{1.20}{2^2} = \frac{1.20}{4} = 0.30\text{ mm/m}^2.

  3. Verify with (x=4,y=4.80 mm)(x = 4, y = 4.80\text{ mm}): A=4.8042=4.8016=0.30 mm/m2A = \frac{4.80}{4^2} = \frac{4.80}{16} = 0.30\text{ mm/m}^2.

Final answer

Model type: Power (Quadratic polynomial through the origin); Exponent: p=2p = 2; Scale factor: A=0.30 mm/m2A = 0.30\text{ mm/m}^2; Governing equation: y(x)=0.30x2y(x) = 0.30x^2

NEXT STEPS
Final Takeaways from Your Teacher
  • Review the distinction between linear scaling (y=mxy = mx) and power scaling (y=Axpy = A x^p) when isolating coefficients.

  • Practice checking fitted parameters against at least two distinct data points from the given dataset.

OverviewACEpath Teacher's Diagnosis

03 A student assumes the model is exponential because deflection values grow rapidly, testing ratios of consecutive y-values rather than finite differences.

Sample Student Work

Reviewed by ACEpath Teacher
Step-by-Step Review
Walk Through It with Your Teacher
Incorrect
  1. Step 1

    Testing ratios of consecutive values: 4.80/1.20=4.0,  10.80/4.80=2.25  ⟹  The values grow rapidly without an initial value at x=0 since y(0)=0, so student approximates an exponential curve.\text{Testing ratios of consecutive values: } 4.80 / 1.20 = 4.0,\; 10.80 / 4.80 = 2.25 \implies \text{The values grow rapidly without an initial value at } x=0 \text{ since } y(0)=0, \text{ so student approximates an exponential curve.}

    Correct

    Δy=[1.20,3.60,6.00,8.40]  ⟹  Δ2y=[2.40,2.40,2.40]  ⟹  Quadratic polynomial / power function y=Axp with y(0)=0\Delta y = [1.20, 3.60, 6.00, 8.40] \implies \Delta^2 y = [2.40, 2.40, 2.40] \implies \text{Quadratic polynomial / power function } y = A x^p \text{ with } y(0)=0

    You calculated consecutive ratios, but because the ratios are unequal (4.0≠2.254.0 \neq 2.25), the data does not represent an exponential curve. Furthermore, standard exponential curves of the form y=Cekxy = C e^{kx} cannot equal zero at x=0x = 0. When you compute the second finite differences of yy at equally spaced xx, they are constant (Δ2y=2.40 mm\Delta^2 y = 2.40\text{ mm}), which proves the underlying model is a quadratic polynomial passing through the origin, equivalent to a power function y=Ax2y = A x^2.

  2. Step 2

    p=e≈2.72  ⟹  A=1.20/22.72≈0.18p = e \approx 2.72 \implies A = 1.20 / 2^{2.72} \approx 0.18

    Correct

    p=ln⁡(4.80)−ln⁡(1.20)ln⁡(4)−ln⁡(2)=ln⁡(4)ln⁡(2)=2  ⟹  A=1.2022=0.03 mm/m2p = \frac{\ln(4.80) - \ln(1.20)}{\ln(4) - \ln(2)} = \frac{\ln(4)}{\ln(2)} = 2 \implies A = \frac{1.20}{2^2} = 0.03\text{ mm/m}^2

    Because you selected an exponential model, you set the exponent pp equal to Euler's number ee rather than calculating the governing power exponent from the log-log slope Δln⁡(y)Δln⁡(x)=2\frac{\Delta \ln(y)}{\Delta \ln(x)} = 2.

  3. Step 3

    The model is an exponential curve with p=2.72 and A=0.18.\text{The model is an exponential curve with } p = 2.72 \text{ and } A = 0.18.

    Correct

    Model type: Power (Quadratic polynomial through origin); p=2;  A=0.03 mm/m2;  y(x)=0.03x2\text{Model type: Power (Quadratic polynomial through origin); } p = 2;\; A = 0.03\text{ mm/m}^2;\; y(x) = 0.03x^2

    Your final parameters and model identification stem directly from the initial model misclassification.

WHAT YOU DID WELL
Compliments from Your Teacher

You recognized that testing consecutive ratios is a standard test for exponential behavior.

You accurately carried out the arithmetic divisions 4.80/1.20=4.04.80 / 1.20 = 4.0 and 10.80/4.80=2.2510.80 / 4.80 = 2.25.

THE ERROR
Where Your ACEpath Teacher Spotted the Mistake
Model Misidentification via Growth Heuristics

no

WHY IT HAPPENED
ACEpath Teacher's Diagnosis

You associated rapid growth with an exponential model even after your ratio test showed varying ratios (4.04.0 vs. 2.252.25) and despite the boundary condition y(0)=0y(0)=0, missing that constant second differences characterize quadratic power growth.

REASONING PATH
Your ACEpath teacher’s suggested approach
Boundary Condition Test
  • A basic exponential function y=Cbxy = C b^x with C≠0C \neq 0 can never evaluate to 00 at x=0x = 0, whereas a power function y=Axpy = A x^p with p>0p > 0 naturally passes through (0,0)(0,0).

  • Check y(0)y(0) first: if y(0)=0y(0) = 0, immediately rule out a pure exponential model y=Cbxy = C b^x.

Model Selection Diagnostic
  • For equally spaced inputs: constant first differences indicate a linear function; constant second differences indicate a quadratic function; constant ratios indicate an exponential function; and a linear plot on ln⁡(y)\ln(y) vs. ln⁡(x)\ln(x) indicates a power function.

  • Compute finite differences Δy\Delta y and Δ2y\Delta^2 y before assuming an exponential model.

CORRECTED PATH
ACEpath Teacher's Demonstration
  1. Notice that y(0)=0y(0) = 0, which rules out an exponential model y=Cekxy = C e^{kx} because e0=1≠0e^0 = 1 \neq 0.

  2. Compute the first finite differences for equally spaced steps of Δx=2\Delta x = 2: 1.20−0.00=1.201.20 - 0.00 = 1.20, 4.80−1.20=3.604.80 - 1.20 = 3.60, 10.80−4.80=6.0010.80 - 4.80 = 6.00, and 19.20−10.80=8.4019.20 - 10.80 = 8.40.

  3. Compute the second finite differences: 3.60−1.20=2.403.60 - 1.20 = 2.40, 6.00−3.60=2.406.00 - 3.60 = 2.40, and 8.40−6.00=2.408.40 - 6.00 = 2.40. Since the second differences are constant, the model is quadratic.

  4. Because the curve passes through the origin (0,0)(0,0) with no linear shift, write y(x)=Ax2y(x) = A x^2, which is a power function with exponent p=2p = 2.

  5. Solve for the scale factor using any point, such as (2,1.20)(2, 1.20): A=1.2022=1.204=0.03 mm/m2A = \frac{1.20}{2^2} = \frac{1.20}{4} = 0.03\text{ mm/m}^2.

Final answer

Model type: Power (Quadratic polynomial through the origin); Exponent: p=2p = 2; Scale factor: A=0.03 mm/m2A = 0.03\text{ mm/m}^2; Governing equation: y(x)=0.03x2y(x) = 0.03x^2

NEXT STEPS
Final Takeaways from Your Teacher
  • Review the criteria for distinguishing polynomial/power functions from exponential functions using finite difference tables.

  • Practice checking log-log slopes Δln⁡(y)Δln⁡(x)\frac{\Delta \ln(y)}{\Delta \ln(x)} to extract power exponents directly from data tables.

Lock it in

Similar question

01

A physical measurement produces coordinates (x,y)(x, y): (1,0.5)(1, 0.5), (2,2.0)(2, 2.0), and (4,8.0)(4, 8.0). Determine whether this data represents an exponential curve or a power function, and find the exponent pp.

Answer

Power function with p=2p = 2. Testing ratios of inputs and outputs: when xx doubles from 11 to 22, yy quadruples (2.0/0.5=4=222.0 / 0.5 = 4 = 2^2). When xx doubles from 22 to 44, yy quadruples (8.0/2.0=4=228.0 / 2.0 = 4 = 2^2). Hence p=ln⁡(4)ln⁡(2)=2p = \frac{\ln(4)}{\ln(2)} = 2.

02

Given equally spaced data at x=1,2,3,4x = 1, 2, 3, 4 with outputs y=5,20,45,80y = 5, 20, 45, 80, verify that the data fits a single-term power model y=Axpy = Ax^p through finite differences, and find AA and pp.

Answer

p=2p = 2, A=5A = 5. First differences are Δy=[15,25,35]\Delta y = [15, 25, 35]. Second differences are Δ2y=[10,10]\Delta^2 y = [10, 10] (constant), confirming a quadratic function p=2p = 2. Substituting (1,5)(1, 5) into y=Ax2y = A x^2 yields 5=A(1)2  ⟹  A=55 = A(1)^2 \implies A = 5.

03

Sensor readings for fluid drag force FF versus velocity vv yield (ln⁡v,ln⁡F)(\ln v, \ln F) pairs of (1.0,2.5)(1.0, 2.5) and (3.0,6.5)(3.0, 6.5). Write the governing power function equation F(v)=CvkF(v) = C v^k.

Answer

F(v)=e0.5v2≈1.65v2F(v) = e^{0.5} v^2 \approx 1.65 v^2. The power exponent is the slope in log-log space: k=6.5−2.53.0−1.0=4.02.0=2k = \frac{6.5 - 2.5}{3.0 - 1.0} = \frac{4.0}{2.0} = 2. The intercept is ln⁡C=ln⁡F−kln⁡v=2.5−2(1.0)=0.5\ln C = \ln F - k\ln v = 2.5 - 2(1.0) = 0.5, giving C=e0.5≈1.65C = e^{0.5} \approx 1.65.

Loading workspace…