Resources

An engineering firm designs rectangular solar panel modules where the length is l ml\text{ m} and the width is w mw\text{ m}. Structural standards require the perimeter not to exceed 24 m24\text{ m}, and electrical cabling specifications constrain the aspect ratio such that l≥1.5wl \ge 1.5w. Rather than maximizing area directly, the engineering team defines a cost-efficiency metric as the diagonal-to-width ratio R=l2+w2wR = \frac{\sqrt{l^2 + w^2}}{w}. Determine the domain constraints on the single variable aspect ratio r=lwr = \frac{l}{w}, express RR strictly as a function of rr, and compute the minimum allowable numerical value of the target ratio RR.

Answer and steps

Final answer

Constraint: r≥1.5r \ge 1.5; Metric function: R(r)=r2+1R(r) = \sqrt{r^2 + 1}; Minimum value: Rmin⁡=132≈1.80R_{\min} = \frac{\sqrt{13}}{2} \approx 1.80

Steps

01

Identify Variables and Determine Domain Constraints on rr

The physical dimensions of the rectangular solar panel are length l>0l > 0 and width w>0w > 0, measured in meters. The aspect ratio is defined as: r=lwr = \frac{l}{w}

The engineering specifications state:

  1. Perimeter constraint: 2(l+w)≤24 m2(l + w) \le 24\text{ m}, which simplifies to l+w≤12l + w \le 12. Substituting l=rwl = rw gives w(1+r)≤12w(1 + r) \le 12. Since ww can be chosen arbitrarily small while remaining strictly positive (0<w≤121+r0 < w \le \frac{12}{1 + r}), this condition places an upper bound on the absolute dimensions for a given rr, but imposes no upper bound on the dimensionless ratio rr itself.
  2. Aspect ratio constraint: l≥1.5wl \ge 1.5w. Dividing both sides by the positive quantity ww yields: r≥1.5r \ge 1.5

Therefore, the domain constraint on the aspect ratio is r≥1.5r \ge 1.5 (or r∈[1.5,∞)r \in [1.5, \infty)).

---](streamdown:incomplete-link)

02

Express the Metric Function RR in Terms of rr

The diagonal-to-width ratio is given by: R=l2+w2wR = \frac{\sqrt{l^2 + w^2}}{w}

Since w>0w > 0, bring ww inside the square root as w2w^2: R=l2+w2w2=(lw)2+1R = \sqrt{\frac{l^2 + w^2}{w^2}} = \sqrt{\left(\frac{l}{w}\right)^2 + 1}

Substituting r=lwr = \frac{l}{w} gives the cost-efficiency metric strictly as a single-variable function: R(r)=r2+1R(r) = \sqrt{r^2 + 1}


03

Compute the Minimum Value of RR

Because f(r)=r2+1f(r) = r^2 + 1 is strictly increasing for all r>0r > 0, the function R(r)=r2+1R(r) = \sqrt{r^2 + 1} is strictly monotonically increasing on its domain [1.5,∞)[1.5, \infty).

Consequently, the minimum value occurs at the lower bound of the domain, r=1.5=32r = 1.5 = \frac{3}{2}: Rmin⁡=R(32)=(32)2+1=94+1=134=132R_{\min} = R\left(\frac{3}{2}\right) = \sqrt{\left(\frac{3}{2}\right)^2 + 1} = \sqrt{\frac{9}{4} + 1} = \sqrt{\frac{13}{4}} = \frac{\sqrt{13}}{2}

Approximating to two decimal places: Rmin⁡=132≈1.80R_{\min} = \frac{\sqrt{13}}{2} \approx 1.80](streamdown:incomplete-link)

Typical errors

OverviewACEpath Teacher's Diagnosis

01 The student mistakenly believes the perimeter constraint imposes an upper bound on the aspect ratio r.

Sample Student Work

Reviewed by ACEpath Teacher
Step-by-Step Review
Walk Through It with Your Teacher
Partially correct
  1. Step 1

    2(l+w)≤24  ⟹  l+w≤12  ⟹  w(r+1)≤122(l + w) \le 24 \implies l + w \le 12 \implies w(r + 1) \le 12

  2. Step 2

    Assuming w≥1 gives r+1≤12, so r≤11  ⟹  Domain of r is 1.5≤r≤11\text{Assuming } w \ge 1 \text{ gives } r + 1 \le 12\text{, so } r \le 11 \implies \text{Domain of } r \text{ is } 1.5 \le r \le 11

    Correct

    r≥1.5r \ge 1.5 (or r∈[1.5,∞)r \in [1.5, \infty))](streamdown:incomplete-link)

    The problem does not state that w≥1w \ge 1. For any arbitrarily large r≥1.5r \ge 1.5, one can choose a sufficiently small positive width w≤12r+1w \le \frac{12}{r + 1} so that the perimeter constraint remains satisfied. Therefore, rr has no finite upper bound.

  3. Step 3

    R=l2+w2w  ⟹  R=(lw)2+1=r2+1R = \frac{\sqrt{l^2 + w^2}}{w} \implies R = \sqrt{\left(\frac{l}{w}\right)^2 + 1} = \sqrt{r^2 + 1}

  4. Step 4

    R is minimized at r=1.5  ⟹  Rmin⁡=1.52+1=3.25=132R \text{ is minimized at } r = 1.5 \implies R_{\min} = \sqrt{1.5^2 + 1} = \sqrt{3.25} = \frac{\sqrt{13}}{2}

WHAT YOU DID WELL
Compliments from Your Teacher

You correctly reformulated the perimeter constraint in terms of width and the aspect ratio.

You correctly simplified the cost-efficiency metric into a single-variable function R(r)=r2+1R(r) = \sqrt{r^2 + 1}.

You correctly identified the lower bound r=1.5r = 1.5 as the minimizer and accurately computed the exact minimum value.

THE ERROR
Where Your ACEpath Teacher Spotted the Mistake
Unjustified Domain Constraint

You assumed that the width ww had a lower limit of 1 m1\text{ m} without any basis in the problem statement.

WHY IT HAPPENED
ACEpath Teacher's Diagnosis

Confusing constraints on absolute physical dimensions with constraints on dimensionless ratios. An upper bound on perimeter limits the maximum scale for a given shape, but because the scale can shrink arbitrarily close to zero, it does not prevent the aspect ratio from becoming arbitrarily large.

REASONING PATH
Your ACEpath teacher’s suggested approach
Dimensionless Ratios vs. Dimensional Bounds
  • A condition of the form w(r+1)≤Cw(r + 1) \le C with w>0w > 0 restricts ww for each fixed rr via w≤Cr+1w \le \frac{C}{r + 1}, but it imposes an upper bound on rr only if ww has an explicit positive minimum wmin⁡w_{\min}.

  • Check whether an explicit minimum dimension is given before concluding that a scale constraint caps a ratio.

CORRECTED PATH
ACEpath Teacher's Demonstration
  1. From l≥1.5wl \ge 1.5w and w>0w > 0, divide by ww to obtain r≥1.5r \ge 1.5.

  2. From w(r+1)≤12w(r + 1) \le 12, any r≥1.5r \ge 1.5 is feasible by selecting 0<w≤12r+10 < w \le \frac{12}{r + 1}.

  3. Conclude that rr has no upper bound, giving domain r≥1.5r \ge 1.5.

Final answer

Domain: r≥1.5r \ge 1.5; Function: R(r)=r2+1R(r) = \sqrt{r^2 + 1}; Minimum value: Rmin⁡=132R_{\min} = \frac{\sqrt{13}}{2}

NEXT STEPS
Final Takeaways from Your Teacher
  • Avoid introducing arbitrary numerical bounds like w≥1w \ge 1 unless they are explicitly given in the problem text.

  • When finding the domain of a ratio variable, test whether extreme values (such as r→∞r \to \infty) remain geometrically possible by shrinking the overall scale.

OverviewACEpath Teacher's Diagnosis

02 The student distributes the square root linearly over addition, incorrectly simplifying R as r + 1.

Sample Student Work

Reviewed by ACEpath Teacher
Step-by-Step Review
Walk Through It with Your Teacher
Partially correct
  1. Step 1

    l≥1.5w and w>0  ⟹  r=lw≥1.5l \ge 1.5w \text{ and } w > 0 \implies r = \frac{l}{w} \ge 1.5

  2. Step 2

    R=l2+w2w=l2+w2w=l+ww=r+1R = \frac{\sqrt{l^2+w^2}}{w} = \frac{\sqrt{l^2} + \sqrt{w^2}}{w} = \frac{l+w}{w} = r + 1

    Correct

    R(r)=l2+w2w2=(lw)2+1=r2+1R(r) = \sqrt{\frac{l^2+w^2}{w^2}} = \sqrt{\left(\frac{l}{w}\right)^2 + 1} = \sqrt{r^2 + 1}

    You distributed the radical linearly across addition by writing l2+w2=l2+w2\sqrt{l^2+w^2} = \sqrt{l^2}+\sqrt{w^2}. Because the square root is non-linear over addition, you must divide inside the radical by rewriting the denominator ww as w2\sqrt{w^2}.

  3. Step 3

    Since R=r+1 is increasing, minimum occurs at r=1.5  ⟹  Rmin⁡=1.5+1=2.5\text{Since } R = r + 1 \text{ is increasing, minimum occurs at } r = 1.5 \implies R_{\min} = 1.5 + 1 = 2.5

    Correct

    Rmin⁡=1.52+1=94+1=132≈1.80R_{\min} = \sqrt{1.5^2 + 1} = \sqrt{\frac{9}{4} + 1} = \frac{\sqrt{13}}{2} \approx 1.80

    Your optimization logic was sound because the ratio function is strictly increasing for positive rr, but substituting into the incorrect linear formula yielded 2.52.5 instead of 132\frac{\sqrt{13}}{2}.

WHAT YOU DID WELL
Compliments from Your Teacher

You correctly established the domain constraint r≥1.5r \ge 1.5 using the geometric inequality l≥1.5wl \ge 1.5w.

You understood that an increasing single-variable function achieves its minimum at the lowest boundary point of its domain.

THE ERROR
Where Your ACEpath Teacher Spotted the Mistake
Linear distribution of radicals over addition

Splitting l2+w2\sqrt{l^2 + w^2} into l2+w2=l+w\sqrt{l^2} + \sqrt{w^2} = l + w.

WHY IT HAPPENED
ACEpath Teacher's Diagnosis

You treated the radical operator as linear across addition, overlooking that a+b≠a+b\sqrt{a+b} \neq \sqrt{a} + \sqrt{b}. To express a ratio containing a radical in terms of a dimensionless variable like r=lwr = \frac{l}{w}, move the outside positive factor into the radical as w=w2w = \sqrt{w^2} before dividing each term under the square root.

REASONING PATH
Your ACEpath teacher’s suggested approach
Radical Non-Linearity Check
  • For positive terms, a2+b2<a+b\sqrt{a^2 + b^2} < a + b. Radicals distribute across multiplication and division, but never across addition or subtraction.

  • Check test numbers: 32+42=5≠3+4=7\sqrt{3^2 + 4^2} = 5 \neq 3 + 4 = 7.

Algebraic Factoring into Radicals
  • When dividing a radical by a positive variable ww, rewrite the denominator as w2\sqrt{w^2} and combine using AB=AB\frac{\sqrt{A}}{\sqrt{B}} = \sqrt{\frac{A}{B}}.

  • Divide each term under the radical by w2w^2: l2+w2w=l2w2+w2w2=r2+1\frac{\sqrt{l^2+w^2}}{w} = \sqrt{\frac{l^2}{w^2} + \frac{w^2}{w^2}} = \sqrt{r^2+1}.

CORRECTED PATH
ACEpath Teacher's Demonstration
  1. Rewrite the denominator as a radical: R=l2+w2w2R = \frac{\sqrt{l^2 + w^2}}{\sqrt{w^2}} for w>0w > 0.

  2. Combine under a single radical: R=l2+w2w2=(lw)2+1=r2+1R = \sqrt{\frac{l^2 + w^2}{w^2}} = \sqrt{\left(\frac{l}{w}\right)^2 + 1} = \sqrt{r^2 + 1}.

  3. Substitute the lower bound r=1.5=32r = 1.5 = \frac{3}{2} into the correct function: Rmin⁡=(32)2+1=94+1=134=132≈1.80R_{\min} = \sqrt{\left(\frac{3}{2}\right)^2 + 1} = \sqrt{\frac{9}{4} + 1} = \sqrt{\frac{13}{4}} = \frac{\sqrt{13}}{2} \approx 1.80.

Final answer

r≥1.5r \ge 1.5; R(r)=r2+1R(r) = \sqrt{r^2 + 1}; Rmin⁡=132≈1.80R_{\min} = \frac{\sqrt{13}}{2} \approx 1.80

NEXT STEPS
Final Takeaways from Your Teacher
  • Review radical properties to ensure you only distribute square roots over multiplication and division, not addition.

  • Practice rewriting rational expressions involving square roots by factoring out or absorbing positive variables into the radicand.

OverviewACEpath Teacher's Diagnosis

03 The student mistakenly thinks the minimum occurs where the derivative with respect to r is zero rather than at the domain boundary.

Sample Student Work

Reviewed by ACEpath Teacher
Step-by-Step Review
Walk Through It with Your Teacher
Partially correct
  1. Step 1

    l≥1.5w means r=lw≥1.5  ⟹  Domain of r is r≥1.5l \ge 1.5w \text{ means } r = \frac{l}{w} \ge 1.5 \implies \text{Domain of } r \text{ is } r \ge 1.5

  2. Step 2

    R=l2+w2w=(lw)2+1  ⟹  R=r2+1R = \frac{\sqrt{l^2 + w^2}}{w} = \sqrt{\left(\frac{l}{w}\right)^2 + 1} \implies R = \sqrt{r^2 + 1}

  3. Step 3

    dRdr=rr2+1  ⟹  Set dRdr=0, so r=0\frac{dR}{dr} = \frac{r}{\sqrt{r^2 + 1}} \implies \text{Set } \frac{dR}{dr} = 0, \text{ so } r = 0

    Correct

    Since dRdr=rr2+1>0\frac{dR}{dr} = \frac{r}{\sqrt{r^2 + 1}} > 0 for all r≥1.5r \ge 1.5, R(r)R(r) is strictly increasing on [1.5,∞)[1.5, \infty), so the minimum occurs at the boundary r=1.5r = 1.5.](streamdown:incomplete-link)

    The critical point r=0r = 0 is outside the domain r≥1.5r \ge 1.5. Because the derivative is strictly positive for all r∈[1.5,∞)r \in [1.5, \infty), the function has no interior stationary points and attains its minimum at the left endpoint.](streamdown:incomplete-link)

  4. Step 4

    Rmin⁡=02+1=1R_{\min} = \sqrt{0^2 + 1} = 1

    Correct

    Rmin⁡=(32)2+1=132≈1.80R_{\min} = \sqrt{\left(\frac{3}{2}\right)^2 + 1} = \frac{\sqrt{13}}{2} \approx 1.80

    Evaluating at the invalid critical point r=0r = 0 produced R=1R = 1 instead of evaluating at the boundary r=1.5r = 1.5.

WHAT YOU DID WELL
Compliments from Your Teacher

You translated the geometric cabling constraint l≥1.5wl \ge 1.5w into the correct domain inequality r≥1.5r \ge 1.5.

You algebraically brought the denominator ww inside the radical to write R(r)=r2+1R(r) = \sqrt{r^2 + 1}.

You correctly computed the derivative dRdr=rr2+1\frac{dR}{dr} = \frac{r}{\sqrt{r^2 + 1}}.

THE ERROR
Where Your ACEpath Teacher Spotted the Mistake
Domain constraint violation in optimization

no

WHY IT HAPPENED
ACEpath Teacher's Diagnosis

You searched for an unconstrained local extremum by solving dRdr=0\frac{dR}{dr} = 0, forgetting to check whether that critical point satisfies the domain constraint r≥1.5r \ge 1.5 or whether the minimum occurs at a boundary endpoint of a monotonic function.

REASONING PATH
Your ACEpath teacher’s suggested approach
Domain verification of critical points
  • Any candidate point from setting f′(x)=0f'(x) = 0 must belong to the domain [a,b)[a, b) before it can be considered.](streamdown:incomplete-link)

  • Check whether r=0r = 0 satisfies r≥1.5r \ge 1.5. Since 0<1.50 < 1.5, reject r=0r = 0 immediately.

Boundary extrema on monotonic intervals
  • If f′(x)>0f'(x) > 0 on the entire interval [a,∞)[a, \infty), then f(x)f(x) is strictly increasing, meaning the minimum must occur at the left boundary x=ax = a.](streamdown:incomplete-link)

  • Evaluate R(r)R(r) at r=1.5r = 1.5 to find the absolute minimum value.

CORRECTED PATH
ACEpath Teacher's Demonstration
  1. Observe that for all r≥1.5r \ge 1.5, the numerator of dRdr=rr2+1\frac{dR}{dr} = \frac{r}{\sqrt{r^2 + 1}} is strictly positive, so dRdr>0\frac{dR}{dr} > 0.

  2. Because the derivative is strictly positive on [1.5,∞)[1.5, \infty), R(r)R(r) is strictly increasing across its entire domain.](streamdown:incomplete-link)

  3. Therefore, the minimum value must occur at the leftmost domain endpoint: r=1.5=32r = 1.5 = \frac{3}{2}.

  4. Evaluate R(32)=(32)2+1=94+1=132R\left(\frac{3}{2}\right) = \sqrt{\left(\frac{3}{2}\right)^2 + 1} = \sqrt{\frac{9}{4} + 1} = \frac{\sqrt{13}}{2}.

Final answer

Domain: r≥1.5r \ge 1.5; Metric function: R(r)=r2+1R(r) = \sqrt{r^2 + 1}; Minimum value: Rmin⁡=132≈1.80R_{\min} = \frac{\sqrt{13}}{2} \approx 1.80

NEXT STEPS
Final Takeaways from Your Teacher
  • Whenever optimizing over a restricted domain, write the interval explicitly (e.g., r∈[1.5,∞)r \in [1.5, \infty)) right above your derivative step.](streamdown:incomplete-link)

  • Before setting f′(r)=0f'(r) = 0, inspect the sign of the derivative on the restricted domain to see if the function is strictly monotonic.

Lock it in

Similar question

01

A rectangular billboard has length ll and width ww. Local zoning requires the perimeter to satisfy 2(l+w)≤30 m2(l + w) \le 30\text{ m}, and aesthetics require l≥2wl \ge 2w. If the structural code additionally mandates w≥1.5 mw \ge 1.5\text{ m}, determine the exact allowable domain of the aspect ratio r=lwr = \frac{l}{w}.

Answer

r∈[2,9]r \in [2, 9]. From l≥2wl \ge 2w, we have r≥2r \ge 2. From w(r+1)≤15w(r + 1) \le 15 and the explicit condition w≥1.5w \ge 1.5, we obtain r+1≤151.5=10r + 1 \le \frac{15}{1.5} = 10, so r≤9r \le 9.

02

An optical slit is modeled as a rectangle of length LL and width WW. The area is capped by A=LW≤50 mm2A = LW \le 50\text{ mm}^2, and diffraction limits require L≥5WL \ge 5W. Assuming only W>0W > 0 with no lower bound, determine the domain of q=LWq = \frac{L}{W} and express the normalized perimeter metric Pnorm=2(L+W)LWP_{\text{norm}} = \frac{2(L + W)}{\sqrt{LW}} as a single-variable function of qq.

Answer

Domain: q≥5q \ge 5. Metric: Pnorm(q)=2(q+1q)P_{\text{norm}}(q) = 2\left(\sqrt{q} + \frac{1}{\sqrt{q}}\right). Since W>0W > 0 can be arbitrarily small, LW≤50LW \le 50 restricts the absolute area, not the dimensionless ratio qq.

03

A cylindrical container has radius r>0r > 0 and height h>0h > 0. Material limits restrict total surface area to 2πrh+2πr2≤1002\pi r h + 2\pi r^2 \le 100. Define the shape ratio λ=hr\lambda = \frac{h}{r}. If design standards require h≥3rh \ge 3r, find the domain of λ\lambda. Then express the ratio of volume to r3r^3, Vrel=Vr3V_{\text{rel}} = \frac{V}{r^3}, strictly in terms of λ\lambda and state whether VrelV_{\text{rel}} has an upper bound on this domain.

Answer

Domain: λ≥3\lambda \ge 3. Metric: Vrel(λ)=πλV_{\text{rel}}(\lambda) = \pi \lambda. There is no upper bound on VrelV_{\text{rel}}, because λ\lambda can be arbitrarily large as r→0+r \to 0^+ while maintaining 2πr2(λ+1)≤1002\pi r^2(\lambda + 1) \le 100.

Loading workspace…