Resources

An analytical chemistry student standardizes an unknown sodium hydroxide solution via titration with potassium hydrogen phthalate (KHP, molar mass =204.22 g/mol= 204.22\text{ g/mol}). The target nominal concentration is exactly 0.1000 M0.1000\text{ M}. In a quality audit of the student's lab technique, n=25n = 25 independent titration replicates are performed, yielding a mean calculated molarity of xˉ=0.1008 M\bar{x} = 0.1008\text{ M} with sample standard deviation s=0.0010 Ms = 0.0010\text{ M}. (a) Perform a two-tailed tt-test of H0:μ=0.1000 MH_0: \mu = 0.1000\text{ M} versus Ha:μ≠0.1000 MH_a: \mu \ne 0.1000\text{ M} at the α=0.01\alpha = 0.01 level (tcrit=±2.797t_{\text{crit}} = \pm 2.797 for df=24df = 24), and state the testing conclusion. (b) Calculate the percentage relative error of the mean concentration relative to the nominal target: % RE=∣xˉ−μ0∣μ0×100%\%\text{ RE} = \frac{|\bar{x} - \mu_0|}{\mu_0} \times 100\%. (c) If standard analytical laboratory protocol specifies that a batch titrant concentration is practically acceptable if its relative error is within ±1.5%\pm 1.5\%, determine whether the difference between the standardized concentration and the nominal target exhibits practical significance (requiring the batch to be discarded/re-prepared) or whether the titrant is practically acceptable for subsequent analytical experiments.

Answer and steps

Final answer

(a) t=0.1008−0.10000.001025=0.00080.00020=4.00t = \frac{0.1008 - 0.1000}{\frac{0.0010}{\sqrt{25}}} = \frac{0.0008}{0.00020} = 4.00. Since ∣t∣=4.00>2.797|t| = 4.00 > 2.797 (p=0.0005<0.01p = 0.0005 < 0.01), reject H0H_0; the difference from nominal concentration is statistically significant. (b) % RE=∣0.1008−0.1000∣0.1000×100%=0.00080.1000×100%=0.80%\%\text{ RE} = \frac{|0.1008 - 0.1000|}{0.1000} \times 100\% = \frac{0.0008}{0.1000} \times 100\% = 0.80\%. (c) Although statistically significantly different from 0.1000 M0.1000\text{ M}, the solution does not exhibit practical deviation because its relative error (0.80%0.80\%) is well within the acceptable analytical tolerance of ±1.5%\pm 1.5\%. The titrant does not need to be discarded; the exact standardized value of 0.1008 M0.1008\text{ M} should simply be used in subsequent titration calculations.

Steps

Part (a): Two-Tailed Single-Sample tt-Test

  1. State the Hypotheses and Significance Level:

    • Null hypothesis: H0:μ=0.1000 MH_0: \mu = 0.1000\text{ M}
    • Alternative hypothesis: Ha:μ≠0.1000 MH_a: \mu \ne 0.1000\text{ M}
    • Significance level: α=0.01\alpha = 0.01
    • Degrees of freedom: df=n−1=25−1=24df = n - 1 = 25 - 1 = 24
    • Critical value: tcrit=±2.797t_{\text{crit}} = \pm 2.797
  2. Calculate the Standard Error of the Mean (SE\text{SE}): SE=sn=0.001025=0.00105=0.00020 M\text{SE} = \frac{s}{\sqrt{n}} = \frac{0.0010}{\sqrt{25}} = \frac{0.0010}{5} = 0.00020\text{ M}
  3. Compute the tt-Statistic: t=xˉ−μ0SE=0.1008−0.10000.00020=0.00080.00020=4.00t = \frac{\bar{x} - \mu_0}{\text{SE}} = \frac{0.1008 - 0.1000}{0.00020} = \frac{0.0008}{0.00020} = 4.00
  4. Statistical Decision:

    • Since ∣t∣=4.00>2.797|t| = 4.00 > 2.797 (which corresponds to p≈0.0005<0.01p \approx 0.0005 < 0.01), the test statistic falls into the critical rejection region.
    • Conclusion: Reject H0H_0. The difference between the sample mean concentration and the nominal target of 0.1000 M0.1000\text{ M} is statistically significant at the α=0.01\alpha = 0.01 level.

Part (b): Percentage Relative Error

Using the formula provided: % RE=∣xˉ−μ0∣μ0×100%\%\text{ RE} = \frac{|\bar{x} - \mu_0|}{\mu_0} \times 100\%

Substitute the given values: % RE=∣0.1008−0.1000∣0.1000×100%=0.00080.1000×100%=0.80%\%\text{ RE} = \frac{|0.1008 - 0.1000|}{0.1000} \times 100\% = \frac{0.0008}{0.1000} \times 100\% = 0.80\%


Part (c): Evaluation of Practical Significance

  • Statistical Significance vs. Practical Significance:
    • Statistical significance determines whether an observed difference is likely due to chance or reflects a true non-zero difference. Because the standard error is very small (SE=0.00020 M\text{SE} = 0.00020\text{ M}), even a tiny difference of 0.0008 M0.0008\text{ M} is easily detected as statistically significant.
    • Practical significance evaluates whether the magnitude of the difference matters in real-world application.
  • Tolerance Comparison:
    • The analytical tolerance standard allows a deviation of up to ±1.5%\pm 1.5\%.
    • The actual deviation is 0.80%0.80\%, which is well below the maximum allowable threshold of 1.5%1.5\%.
  • Conclusion:
    • The difference does not exhibit practical significance.
    • The titrant batch is practically acceptable and does not need to be discarded. In subsequent titration work, the analyst simply uses the standardized concentration of 0.1008 M0.1008\text{ M} instead of the nominal 0.1000 M0.1000\text{ M} to ensure accurate stoichiometric calculations.

Typical errors

OverviewACEpath Teacher's Diagnosis

01 The student forgets to divide the sample standard deviation by the square root of n when computing the standard error, leading to a failure to reject the null hypothesis.

Sample Student Work

Reviewed by ACEpath Teacher
Step-by-Step Review
Walk Through It with Your Teacher
Partially correct
  1. Step 1

    t=xˉ−μ0s=0.1008−0.10000.0010  ⟹  t=0.00080.0010=0.800t = \frac{\bar{x} - \mu_0}{s} = \frac{0.1008 - 0.1000}{0.0010} \implies t = \frac{0.0008}{0.0010} = 0.800

    Correct

    t=xˉ−μ0s/n=0.1008−0.10000.0010/25=0.00080.00020=4.00t = \frac{\bar{x} - \mu_0}{s / \sqrt{n}} = \frac{0.1008 - 0.1000}{0.0010 / \sqrt{25}} = \frac{0.0008}{0.00020} = 4.00

    You divided by the sample standard deviation ss instead of the standard error of the mean SE=sn\text{SE} = \frac{s}{\sqrt{n}}. Because n=25n = 25, the standard error is 0.001025=0.00020 M\frac{0.0010}{\sqrt{25}} = 0.00020\text{ M}, yielding t=4.00t = 4.00.

  2. Step 2

    Since ∣t∣=0.800<2.797|t| = 0.800 < 2.797, fail to reject H0H_0; the difference is not statistically significant.

    Correct

    Since ∣t∣=4.00>2.797|t| = 4.00 > 2.797, reject H0H_0; the difference from nominal concentration is statistically significant at α=0.01\alpha = 0.01.

    Because your calculated tt-statistic was affected by omitting n\sqrt{n}, your test decision was reversed. Comparing the correct value ∣t∣=4.00|t| = 4.00 to 2.7972.797 leads to rejecting H0H_0.

  3. Step 3

    % RE\text{ RE} = (∣0.1008−0.1000∣0.1000)\left(\frac{|0.1008 - 0.1000|}{0.1000}\right) ×\times 100%   ⟹  \implies % RE\text{ RE} = (0.00080.1000)\left(\frac{0.0008}{0.1000}\right) ×\times 100% = 0.8%

  4. Step 4

    Since 0.8%0.8\% is within ±1.5%\pm 1.5\%, the titrant is practically acceptable.

WHAT YOU DID WELL
Compliments from Your Teacher

You set up the percentage relative error formula and computed the value accurately.

You correctly interpreted the analytical tolerance specification to judge practical acceptability.

You correctly compared your calculated test statistic against the critical value to state a testing decision.

THE ERROR
Where Your ACEpath Teacher Spotted the Mistake
Omission of sample size in standard error

You used the sample standard deviation ss directly in the denominator of the single-sample tt-test rather than dividing by n\sqrt{n}.

WHY IT HAPPENED
ACEpath Teacher's Diagnosis

You conflated individual variability (ss) with the variability of the sample mean (SE=s/n\text{SE} = s/\sqrt{n}). In hypothesis testing about a population mean μ\mu, the sampling distribution of xˉ\bar{x} has spread s/ns/\sqrt{n}, not ss.

REASONING PATH
Your ACEpath teacher’s suggested approach
Standard Deviation vs. Standard Error
  • The tt-statistic for a one-sample mean test compares xˉ−μ0\bar{x} - \mu_0 to the standard error of the mean: SE=sn\text{SE} = \frac{s}{\sqrt{n}}.

  • Whenever testing hypotheses about a population mean μ\mu, always write down SE=sn\text{SE} = \frac{s}{\sqrt{n}} before assembling the fraction for tt.

Statistical vs. Practical Significance
  • A test can be statistically significant (large nn makes SE\text{SE} small, so small deviations produce a large tt) even when the physical deviation is practically negligible.

  • Check whether a statistically significant result actually impacts practical decisions by comparing effect size or relative error against domain tolerance limits.

CORRECTED PATH
ACEpath Teacher's Demonstration
  1. Compute the standard error of the mean: SE=sn=0.001025=0.00020 M\text{SE} = \frac{s}{\sqrt{n}} = \frac{0.0010}{\sqrt{25}} = 0.00020\text{ M}.

  2. Calculate the tt-statistic: t=0.1008−0.10000.00020=0.00080.00020=4.00t = \frac{0.1008 - 0.1000}{0.00020} = \frac{0.0008}{0.00020} = 4.00.

  3. Compare with the critical value: ∣t∣=4.00>2.797|t| = 4.00 > 2.797, so reject H0H_0. The difference is statistically significant.

  4. Combine with parts (b) and (c): Although the concentration is statistically significantly different from 0.1000 M0.1000\text{ M}, its relative error (0.80%0.80\%) is within ±1.5%\pm 1.5\%, so it is practically acceptable.

Final answer

(a) t=4.00>2.797t = 4.00 > 2.797; reject H0H_0, statistically significant. (b) % RE=0.80%\%\text{ RE} = 0.80\%. (c) Practically acceptable.

NEXT STEPS
Final Takeaways from Your Teacher
  • Review the distinction between sample standard deviation ss (spread of individual data points) and standard error s/ns/\sqrt{n} (spread of sample means).

  • Practice identifying when large sample sizes produce statistical significance for practically negligible effect sizes.

OverviewACEpath Teacher's Diagnosis

02 The student divides by the sample size n instead of the square root of n when calculating the standard error of the mean.

Sample Student Work

Reviewed by ACEpath Teacher
Step-by-Step Review
Walk Through It with Your Teacher
Partially correct
  1. Step 1

    t=xˉ−μ0s/n=0.1008−0.10000.0010/25  ⟹  t=0.00080.00004=20.000t = \frac{\bar{x} - \mu_0}{s/n} = \frac{0.1008 - 0.1000}{0.0010/25} \implies t = \frac{0.0008}{0.00004} = 20.000

    Correct

    t=xˉ−μ0s/n=0.1008−0.10000.0010/25=0.00080.00020=4.00t = \frac{\bar{x} - \mu_0}{s/\sqrt{n}} = \frac{0.1008 - 0.1000}{0.0010/\sqrt{25}} = \frac{0.0008}{0.00020} = 4.00

    You used s/ns/n in the denominator instead of the standard error formula SE=s/n\text{SE} = s/\sqrt{n}. Dividing by n=25n = 25 rather than 25=5\sqrt{25} = 5 gave an inflated tt-statistic of 20.00020.000 instead of 4.004.00.

  2. Step 2

    Since ∣t∣=20.000>2.797, reject H0; the difference is statistically significant.\text{Since } |t| = 20.000 > 2.797\text{, reject } H_0\text{; the difference is statistically significant.}

    Correct

    Since ∣t∣=4.00>2.797, reject H0; the difference is statistically significant.\text{Since } |t| = 4.00 > 2.797\text{, reject } H_0\text{; the difference is statistically significant.}

    Your decision rule and conclusion to reject the null hypothesis are logically sound, but your numerical comparison inherited the incorrectly calculated test statistic.

  3. Step 3

    % RE\text{ RE} = ∣0.1008−0.1000∣0.1000\frac{|0.1008 - 0.1000|}{0.1000} ×\times 100%   ⟹  \implies % RE\text{ RE} = 0.00080.1000\frac{0.0008}{0.1000} ×\times 100% = 0.8%

  4. Step 4

    Since 0.8% is within ±1.5%, the titrant is practically acceptable.\text{Since } 0.8\% \text{ is within } \pm 1.5\%\text{, the titrant is practically acceptable.}

WHAT YOU DID WELL
Compliments from Your Teacher

You correctly set up and calculated the percentage relative error in Part (b).

You correctly recognized that a statistically significant result can still be practically acceptable when it falls within operational tolerances.

THE ERROR
Where Your ACEpath Teacher Spotted the Mistake
Standard Error Formula Confusion

no

WHY IT HAPPENED
ACEpath Teacher's Diagnosis

You confused the standard error of the sample mean (SE=s/n\text{SE} = s/\sqrt{n}) with dividing the sample standard deviation directly by the sample size (s/ns/n).

REASONING PATH
Your ACEpath teacher’s suggested approach
Standard Error of the Mean
  • The standard error of the mean measures the variability of sample averages and equals SE=sn\text{SE} = \frac{s}{\sqrt{n}}, not sn\frac{s}{n}.

  • Always take the square root of the sample size before dividing the standard deviation when computing zz or tt test statistics.

CORRECTED PATH
ACEpath Teacher's Demonstration
  1. SE=sn=0.001025=0.00105=0.00020 M\text{SE} = \frac{s}{\sqrt{n}} = \frac{0.0010}{\sqrt{25}} = \frac{0.0010}{5} = 0.00020\text{ M}

  2. t=xˉ−μ0SE=0.1008−0.10000.00020=0.00080.00020=4.00t = \frac{\bar{x} - \mu_0}{\text{SE}} = \frac{0.1008 - 0.1000}{0.00020} = \frac{0.0008}{0.00020} = 4.00

  3. Compare ∣t∣=4.00 to tcrit=2.797. Since 4.00>2.797, reject H0.\text{Compare } |t| = 4.00 \text{ to } t_{\text{crit}} = 2.797\text{. Since } 4.00 > 2.797\text{, reject } H_0\text{.}

Final answer

(a) t=4.00t = 4.00; reject H0H_0 (statistically significant). (b) % RE=0.80%\%\text{ RE} = 0.80\%. (c) The solution does not exhibit practical significance and is practically acceptable.

NEXT STEPS
Final Takeaways from Your Teacher
  • Review the Central Limit Theorem formula for standard error: σxˉ=σn\sigma_{\bar{x}} = \frac{\sigma}{\sqrt{n}}.

  • Practice identifying whether a denominator requires nn (such as sample variance formulas) or n\sqrt{n} (such as standard error of sample means).

OverviewACEpath Teacher's Diagnosis

03 The student conflates statistical significance with practical significance, incorrectly concluding that rejecting the null hypothesis requires discarding the batch.

Sample Student Work

Reviewed by ACEpath Teacher
Step-by-Step Review
Walk Through It with Your Teacher
Partially correct
  1. Step 1

    t=xˉ−μ0s/n=0.1008−0.10000.0010/25  ⟹  t=0.00080.0002=4.000  ⟹  Since ∣t∣=4.000>2.797, reject H0; the difference is statistically significant.t = \frac{\bar{x} - \mu_0}{s/\sqrt{n}} = \frac{0.1008 - 0.1000}{0.0010/\sqrt{25}} \implies t = \frac{0.0008}{0.0002} = 4.000 \implies \text{Since } |t| = 4.000 > 2.797\text{, reject } H_0\text{; the difference is statistically significant.}

  2. Step 2

    % RE\text{ RE} = (∣0.1008−0.1000∣0.1000)\left(\frac{|0.1008 - 0.1000|}{0.1000}\right) ×\times 100%   ⟹  \implies % RE\text{ RE} = (0.00080.1000)\left(\frac{0.0008}{0.1000}\right) ×\times 100% = 0.8%

  3. Step 3

    Since \text{Since } H_0  was rejected, so the batch exhibits practical significance and must be discarded.\text{ was rejected, so the batch exhibits practical significance and must be discarded.}

    Correct

    Since \text{Since } % RE\text{ RE} = 0.80% ≤\le 1.5%, the deviation does not exhibit practical significance. The batch is acceptable and should be kept using \text{, the deviation does not exhibit practical significance. The batch is acceptable and should be kept using } 0.1008 M\text{ M}.

    You treated the rejection of H0H_0 as evidence of practical significance. Statistical significance only indicates that the true mean is reliably different from 0.1000 M0.1000\text{ M} (not zero difference), whereas practical significance depends on whether the magnitude of the difference (0.80%0.80\%) exceeds the practical tolerance standard (pm1.5%\\pm 1.5\%).

WHAT YOU DID WELL
Compliments from Your Teacher

You correctly calculated the test statistic and conducted the two-tailed tt-test.

You calculated the relative error correctly using the given formula.

THE ERROR
Where Your ACEpath Teacher Spotted the Mistake
Conflating statistical significance with practical significance

no

WHY IT HAPPENED
ACEpath Teacher's Diagnosis

You assumed that rejecting the null hypothesis in a hypothesis test automatically implies that the observed difference is practically meaningful or harmful in a real-world setting, overlooking the specific practical tolerance threshold (±1.5%\pm 1.5\%) given in the problem.

REASONING PATH
Your ACEpath teacher’s suggested approach
Define Practical vs. Statistical Significance
  • Statistical significance (p<αp < \alpha) means the observed effect is unlikely to be due to sampling noise. Practical significance means the effect size is large enough to matter in domain application.

  • Always evaluate practical significance by comparing the calculated effect or error directly against the specified tolerance threshold, not by looking at the pp-value or rejection decision alone.

CORRECTED PATH
ACEpath Teacher's Demonstration
  1. Compare the calculated relative error (% RE=0.80%\%\text{ RE} = 0.80\%) to the laboratory protocol tolerance (1.5%1.5\%).

  2. Notice that 0.80%<1.5%0.80\% < 1.5\%, so the error is well within acceptable experimental limits.

  3. Conclude that the difference does not exhibit practical significance, and the batch is practically acceptable to use with its calibrated concentration of 0.1008 M0.1008\text{ M}.

Final answer

The batch does not exhibit practical significance because its relative error (0.80%0.80\%) is within the ±1.5%\pm 1.5\% tolerance; therefore, the titrant is practically acceptable and should be retained using xˉ=0.1008 M\bar{x} = 0.1008\text{ M}.

NEXT STEPS
Final Takeaways from Your Teacher
  • Review the distinction between statistical significance (p<αp < \alpha) and practical significance (effect size within engineering or scientific tolerance).

  • Practice separating hypothesis test conclusions (reject/fail to reject H0H_0) from operational decision-making thresholds.

Lock it in

Similar question

01

A quality control engineer inspects a component with target thickness 5.000 mm5.000\text{ mm}. A sample of n=16n = 16 components has mean xˉ=5.012 mm\bar{x} = 5.012\text{ mm} and standard deviation s=0.016 mms = 0.016\text{ mm}. Calculate the test statistic tt for testing H0:μ=5.000 mmH_0: \mu = 5.000\text{ mm}.

Answer

t=3.00t = 3.00. Steps: SE=sn=0.01616=0.004 mm\text{SE} = \frac{s}{\sqrt{n}} = \frac{0.016}{\sqrt{16}} = 0.004\text{ mm}; t=5.012−5.0000.004=0.0120.004=3.00t = \frac{5.012 - 5.000}{0.004} = \frac{0.012}{0.004} = 3.00.

02

An automated pill-filling machine is calibrated for 500.0 mg500.0\text{ mg} tablets. An audit of n=100n = 100 tablets yields xˉ=500.4 mg\bar{x} = 500.4\text{ mg} with s=1.0 mgs = 1.0\text{ mg}. (a) Calculate tt and state whether the difference is statistically significant at α=0.05\alpha = 0.05 (tcrit=±1.984t_{\text{crit}} = \pm 1.984). (b) If pharmacy regulations allow a practical tolerance of ±1.0%\pm 1.0\%, is this difference practically significant?

Answer

(a) t=4.00>1.984t = 4.00 > 1.984, so reject H0H_0 (statistically significant). (b) % RE=∣500.4−500.0∣500.0×100%=0.08%\%\text{ RE} = \frac{|500.4 - 500.0|}{500.0} \times 100\% = 0.08\%. Since 0.08%≤1.0%0.08\% \le 1.0\%, the difference is not practically significant (the batch is practically acceptable).

03

A clinical trial compares a new drug to a standard drug. In a sample of n=10,000n = 10{,}000 patients, blood pressure dropped by xˉ=0.3 mmHg\bar{x} = 0.3\text{ mmHg} more than control (p=0.002p = 0.002). Medical guidelines state a reduction of at least 5.0 mmHg5.0\text{ mmHg} is required for clinical benefit. Explain why p<0.01p < 0.01 occurred and state whether the drug should be adopted.

Answer

The huge sample size (n=10,000n = 10{,}000) made the standard error extremely small, enabling the test to detect a tiny difference of 0.3 mmHg0.3\text{ mmHg} as statistically significant. However, because 0.3 mmHg≪5.0 mmHg0.3\text{ mmHg} \ll 5.0\text{ mmHg}, the drug lacks clinical (practical) significance and should not be adopted based on this effect size alone.

Loading workspace…