Resources

An industrial packaging facility transports packages down an inclined loading ramp into a deceleration zone. A package of mass m=15.0 kgm = 15.0\text{ kg} is released from rest at the top of a ramp inclined at angle θ=30.0∘\theta = 30.0^\circ of incline length s1=8.00 ms_1 = 8.00\text{ m} with kinetic friction coefficient μ1=0.200\mu_1 = 0.200. At the bottom, it transitions smoothly onto a horizontal deceleration track where a variable kinetic friction coating provides μ2=0.400\mu_2 = 0.400. Safety constraints mandate that the maximum horizontal stopping distance s2s_2 must not exceed 12.0 m12.0\text{ m}, and the arrival velocity v1v_1 at the bottom of the ramp must not exceed 9.00 m/s9.00\text{ m/s}. Using g=9.80 m/s2g = 9.80\text{ m/s}^2, define the coupled work-energy kinematic equations governing both segments, determine v1v_1 and s2s_2, and verify if the design complies with both safety constraints.

Answer and steps

Final answer

v1=2gs1(sin⁡30.0∘−μ1cos⁡30.0∘)≈7.17 m/sv_1 = \sqrt{2gs_1(\sin 30.0^\circ - \mu_1 \cos 30.0^\circ)} \approx 7.17\text{ m/s}; s2=v122μ2g≈6.55 ms_2 = \frac{v_1^2}{2\mu_2 g} \approx 6.55\text{ m}; Both constraints are satisfied since v1=7.17 m/s≤9.00 m/sv_1 = 7.17\text{ m/s} \le 9.00\text{ m/s} and s2=6.55 m≤12.0 ms_2 = 6.55\text{ m} \le 12.0\text{ m}.

Steps

01

Modeling the Incline Segment

A package of mass mm starts from rest at the top of the ramp of length s1s_1 inclined at angle θ\theta.

The forces acting along the perpendicular and parallel directions to the incline are:

  • Normal force: N1=mgcos⁡θN_1 = m g \cos\theta
  • Kinetic friction force: fk1=μ1N1=μ1mgcos⁡θf_{k1} = \mu_1 N_1 = \mu_1 m g \cos\theta
  • Component of gravity along the incline: Fg,∥=mgsin⁡θF_{g,\parallel} = m g \sin\theta

Applying the Work-Energy Theorem (ΔK=Wnet\Delta K = W_{\text{net}}) over the displacement s1s_1: Wnet=(mgsin⁡θ−μ1mgcos⁡θ)s1=12mv12−0W_{\text{net}} = (m g \sin\theta - \mu_1 m g \cos\theta) s_1 = \frac{1}{2} m v_1^2 - 0

Dividing both sides by 12m\frac{1}{2}m yields the arrival velocity v1v_1: v1=2gs1(sin⁡θ−μ1cos⁡θ)v_1 = \sqrt{2 g s_1 (\sin\theta - \mu_1 \cos\theta)}

Substituting the given values (g=9.80 m/s2g = 9.80\text{ m/s}^2, s1=8.00 ms_1 = 8.00\text{ m}, θ=30.0∘\theta = 30.0^\circ, and μ1=0.200\mu_1 = 0.200): sin⁡30.0∘=0.500,cos⁡30.0∘≈0.866\sin 30.0^\circ = 0.500,\quad \cos 30.0^\circ \approx 0.866 sin⁡30.0∘−μ1cos⁡30.0∘=0.500−0.200(0.866)≈0.327\sin 30.0^\circ - \mu_1 \cos 30.0^\circ = 0.500 - 0.200(0.866) \approx 0.327 v1=2(9.80)(8.00)(0.327)≈7.17 m/sv_1 = \sqrt{2(9.80)(8.00)(0.327)} \approx 7.17\text{ m/s}

02

Modeling the Horizontal Deceleration Segment

On the flat deceleration track, the package enters with velocity v1v_1 and comes to rest (v2=0v_2 = 0) after traveling a distance s2s_2.

The normal force is N2=mgN_2 = m g, so the friction force acting against motion is: fk2=μ2mgf_{k2} = \mu_2 m g

Applying the Work-Energy Theorem over distance s2s_2: Wnet=−fk2s2=0−12mv12W_{\text{net}} = - f_{k2} s_2 = 0 - \frac{1}{2} m v_1^2 −μ2mgs2=−12mv12-\mu_2 m g s_2 = -\frac{1}{2} m v_1^2

Solving for the stopping distance s2s_2: s2=v122μ2gs_2 = \frac{v_1^2}{2 \mu_2 g}

Substituting v1≈7.17 m/sv_1 \approx 7.17\text{ m/s}, μ2=0.400\mu_2 = 0.400, and g=9.80 m/s2g = 9.80\text{ m/s}^2: s2=(7.17)22(0.400)(9.80)≈6.55 ms_2 = \frac{(7.17)^2}{2(0.400)(9.80)} \approx 6.55\text{ m}

(Note: Mass mm cancels in both equations, showing that motion under Coulomb friction alone is independent of package mass.)

03

Verification Against Design Constraints

Comparing the calculated quantities against the safety requirements:

  1. Arrival velocity constraint: v1=7.17 m/s≤9.00 m/s(Satisfied)v_1 = 7.17\text{ m/s} \le 9.00\text{ m/s}\quad \text{(Satisfied)}
  2. Horizontal stopping distance constraint: s2=6.55 m≤12.0 m(Satisfied)s_2 = 6.55\text{ m} \le 12.0\text{ m}\quad \text{(Satisfied)}

Both design safety constraints are satisfied.

Typical errors

OverviewACEpath Teacher's Diagnosis

01 A student confuses the trigonometric components on the incline by using sin(θ) instead of cos(θ) for the normal force, leading to an incorrect friction force and arrival velocity.

Sample Student Work

Reviewed by ACEpath Teacher
Step-by-Step Review
Walk Through It with Your Teacher
Incorrect
  1. Step 1

    Wnet=m⋅g⋅s1⋅sin⁡(θ)−μ1⋅m⋅g⋅sin⁡(θ)⋅s1=12mv12  ⟹  v12=2(9.80)(8.00)(sin⁡(30.0∘)−0.200sin⁡(30.0∘))=62.72 m2/s2  ⟹  v1=7.92 m/sW_{\text{net}} = m \cdot g \cdot s_1 \cdot \sin(\theta) - \mu_1 \cdot m \cdot g \cdot \sin(\theta) \cdot s_1 = \frac{1}{2} m v_1^2 \implies v_1^2 = 2(9.80)(8.00)(\sin(30.0^\circ) - 0.200\sin(30.0^\circ)) = 62.72\text{ m}^2/\text{s}^2 \implies v_1 = 7.92\text{ m/s}

    Correct

    Wnet=mgs1sin⁡θ−μ1mgcos⁡θs1=12mv12  ⟹  v1=2(9.80)(8.00)(sin⁡30.0∘−0.200cos⁡30.0∘)≈7.17 m/sW_{\text{net}} = m g s_1 \sin\theta - \mu_1 m g \cos\theta s_1 = \frac{1}{2} m v_1^2 \implies v_1 = \sqrt{2(9.80)(8.00)(\sin 30.0^\circ - 0.200\cos 30.0^\circ)} \approx 7.17\text{ m/s}

    You resolved the normal force perpendicular to the ramp as mgsin⁡θmg\sin\theta instead of mgcos⁡θmg\cos\theta. Because the incline makes an angle θ\theta with the horizontal, the perpendicular component of gravity balanced by the normal force is N1=mgcos⁡θN_1 = mg\cos\theta, making the friction work −μ1mgs1cos⁡θ-\mu_1 mg s_1 \cos\theta.

  2. Step 2

    −μ2⋅m⋅g⋅s2=0−12mv12  ⟹  s2=v122μ2g=62.727.84=8.00 m-\mu_2 \cdot m \cdot g \cdot s_2 = 0 - \frac{1}{2} m v_1^2 \implies s_2 = \frac{v_1^2}{2\mu_2 g} = \frac{62.72}{7.84} = 8.00\text{ m}

    Correct

    s2=v122μ2g=(7.17)22(0.400)(9.80)≈6.55 ms_2 = \frac{v_1^2}{2\mu_2 g} = \frac{(7.17)^2}{2(0.400)(9.80)} \approx 6.55\text{ m}

    Your horizontal work-energy equation and algebraic isolation of s2s_2 are completely correct, but the numerical result is affected by substituting your earlier value of v12=62.72 m2/s2v_1^2 = 62.72\text{ m}^2/\text{s}^2 instead of 51.27 m2/s251.27\text{ m}^2/\text{s}^2.

  3. Step 3

    v1=7.92 m/s≤9.00 m/s  ⟹  s2=8.00 m≤12.0 m  ⟹  The design complies with both safety constraints.v_1 = 7.92\text{ m/s} \le 9.00\text{ m/s} \implies s_2 = 8.00\text{ m} \le 12.0\text{ m} \implies \text{The design complies with both safety constraints.}

    Correct

    v1≈7.17 m/s≤9.00 m/s and s2≈6.55 m≤12.0 m  ⟹  Both design safety constraints are satisfied.v_1 \approx 7.17\text{ m/s} \le 9.00\text{ m/s} \text{ and } s_2 \approx 6.55\text{ m} \le 12.0\text{ m} \implies \text{Both design safety constraints are satisfied.}

    You correctly structured the comparison against the given threshold values, though the specific values you checked were carried over from the earlier component error.

WHAT YOU DID WELL
Compliments from Your Teacher

You correctly applied the work-energy theorem to both segments of motion.

You correctly identified that the normal force on the flat deceleration track is N2=mgN_2 = mg.

You correctly set up and evaluated the inequality checks for both design constraints.

THE ERROR
Where Your ACEpath Teacher Spotted the Mistake
Trigonometric Component Confusion

Using sin⁡θ\sin\theta instead of cos⁡θ\cos\theta when finding the normal force on an inclined plane.

WHY IT HAPPENED
ACEpath Teacher's Diagnosis

You confused the parallel and perpendicular components of gravity relative to the inclined surface. Gravity acts straight down, so with an angle measured from the horizontal, the component perpendicular to the ramp is mgcos⁡θmg\cos\theta, while the downhill component is mgsin⁡θmg\sin\theta.

REASONING PATH
Your ACEpath teacher’s suggested approach
Normal Force on an Incline
  • N=mgcos⁡θN = mg\cos\theta when the angle θ\theta is measured relative to the horizontal.

  • Draw a right triangle with gravity mgmg as the hypotenuse, and verify that the side adjacent to angle θ\theta is perpendicular to the ramp surface.

Component Check at Extremes
  • As θ→0∘\theta \to 0^\circ (flat ground), N→mgN \to mg; as θ→90∘\theta \to 90^\circ (vertical wall), N→0N \to 0.

  • Check your formula: cos⁡(0∘)=1\cos(0^\circ) = 1 matches flat ground, whereas sin⁡(0∘)=0\sin(0^\circ) = 0 would incorrectly yield zero normal force on a horizontal surface.

CORRECTED PATH
ACEpath Teacher's Demonstration
  1. Set the normal force perpendicular to the ramp: N1=mgcos⁡θN_1 = mg\cos\theta.

  2. Write the kinetic friction force: fk1=μ1N1=μ1mgcos⁡θf_{k1} = \mu_1 N_1 = \mu_1 mg\cos\theta.

  3. Calculate net work along the ramp: Wnet=mgs1(sin⁡30.0∘−μ1cos⁡30.0∘)=(15.0)(9.80)(8.00)(0.500−0.200×0.866)≈384.5 JW_{\text{net}} = mg s_1(\sin 30.0^\circ - \mu_1 \cos 30.0^\circ) = (15.0)(9.80)(8.00)(0.500 - 0.200 \times 0.866) \approx 384.5\text{ J}.

  4. Solve for v1v_1: v1=2gs1(sin⁡30.0∘−μ1cos⁡30.0∘)=2(9.80)(8.00)(0.3268)≈7.17 m/sv_1 = \sqrt{2gs_1(\sin 30.0^\circ - \mu_1 \cos 30.0^\circ)} = \sqrt{2(9.80)(8.00)(0.3268)} \approx 7.17\text{ m/s}.

  5. Substitute v12≈51.4 m2/s2v_1^2 \approx 51.4\text{ m}^2/\text{s}^2 into the horizontal segment: s2=v122μ2g=51.42(0.400)(9.80)≈6.55 ms_2 = \frac{v_1^2}{2\mu_2 g} = \frac{51.4}{2(0.400)(9.80)} \approx 6.55\text{ m}.

  6. Verify constraints: v1=7.17 m/s≤9.00 m/sv_1 = 7.17\text{ m/s} \le 9.00\text{ m/s} and s2=6.55 m≤12.0 ms_2 = 6.55\text{ m} \le 12.0\text{ m}.

Final answer

v1≈7.17 m/sv_1 \approx 7.17\text{ m/s}, s2≈6.55 ms_2 \approx 6.55\text{ m}; both safety constraints are satisfied.

NEXT STEPS
Final Takeaways from Your Teacher
  • Always sketch a dedicated free-body diagram showing axes aligned along and perpendicular to the inclined ramp.

  • Test component formulas against extreme angles (θ=0∘\theta = 0^\circ and θ=90∘\theta = 90^\circ) before substituting values into work-energy equations.

OverviewACEpath Teacher's Diagnosis

02 A student forgets to subtract the work done by friction along the ramp, treating the ramp as frictionless when determining the arrival velocity.

Sample Student Work

Reviewed by ACEpath Teacher
Step-by-Step Review
Walk Through It with Your Teacher
Incorrect
  1. Step 1

    m⋅g⋅s1⋅sin⁡(θ)=12mv12  ⟹  v12=2gs1sin⁡(θ)=2(9.80)(8.00)sin⁡(30.0∘)=78.4 m2/s2  ⟹  v1=8.85 m/sm \cdot g \cdot s_1 \cdot \sin(\theta) = \frac{1}{2} m v_1^2 \implies v_1^2 = 2 g s_1 \sin(\theta) = 2(9.80)(8.00)\sin(30.0^\circ) = 78.4\text{ m}^2/\text{s}^2 \implies v_1 = 8.85\text{ m/s}

    Correct

    Wnet=(mgsin⁡θ−μ1mgcos⁡θ)s1=12mv12  ⟹  v1=2gs1(sin⁡θ−μ1cos⁡θ)≈7.17 m/sW_{\text{net}} = (m g \sin\theta - \mu_1 m g \cos\theta) s_1 = \frac{1}{2} m v_1^2 \implies v_1 = \sqrt{2 g s_1 (\sin\theta - \mu_1 \cos\theta)} \approx 7.17\text{ m/s}

    You did not include the thermal energy dissipated by friction on the ramp. Because the ramp has a coefficient of kinetic friction μ1=0.200\mu_1 = 0.200, the net force along the incline is mgsin⁡θ−μ1mgcos⁡θm g \sin\theta - \mu_1 m g \cos\theta, not simply mgsin⁡θm g \sin\theta.

  2. Step 2

    −μ2mgs2=0−12mv12  ⟹  s2=v122μ2g=78.42(0.400)(9.80)=78.47.84=10.0 m-\mu_2 m g s_2 = 0 - \frac{1}{2} m v_1^2 \implies s_2 = \frac{v_1^2}{2 \mu_2 g} = \frac{78.4}{2(0.400)(9.80)} = \frac{78.4}{7.84} = 10.0\text{ m}

    Correct

    s2=v122μ2g=(7.17)22(0.400)(9.80)≈6.55 ms_2 = \frac{v_1^2}{2 \mu_2 g} = \frac{(7.17)^2}{2(0.400)(9.80)} \approx 6.55\text{ m}

    Your work-energy equation and algebraic isolation of s2s_2 on the flat track are completely correct. However, substituting your earlier unretarded velocity value of v12=78.4 m2/s2v_1^2 = 78.4\text{ m}^2/\text{s}^2 led to s2=10.0 ms_2 = 10.0\text{ m} instead of 6.55 m6.55\text{ m}.

  3. Step 3

    v1=8.85 m/s≤9.00 m/sv_1 = 8.85\text{ m/s} \le 9.00\text{ m/s}, s2=10.0 m≤12.0 m  ⟹  s_2 = 10.0\text{ m} \le 12.0\text{ m} \implies The design complies with both safety constraints.

    Correct

    v1=7.17 m/s≤9.00 m/sv_1 = 7.17\text{ m/s} \le 9.00\text{ m/s} and s2=6.55 m≤12.0 m  ⟹  s_2 = 6.55\text{ m} \le 12.0\text{ m} \implies Both safety constraints are satisfied.

    Your comparison logic against the safety thresholds is sound, but your numerical checks relied on the values propagated from the initial omission of ramp friction.

WHAT YOU DID WELL
Compliments from Your Teacher

You recognized that work-energy methods apply across both individual segments of motion.

You correctly modeled the horizontal deceleration phase using the work done by friction −μ2mgs2=ΔK-\mu_2 m g s_2 = \Delta K.

You systematically checked the computed kinematic values against the design safety thresholds.

THE ERROR
Where Your ACEpath Teacher Spotted the Mistake
Omission of Friction on Incline

You set the net work along the ramp equal to gravitational potential energy lost without subtracting the work performed against friction.

WHY IT HAPPENED
ACEpath Teacher's Diagnosis

Overlooking non-conservative surface forces in mechanical energy balances when a friction coefficient is specified for an inclined plane.

REASONING PATH
Your ACEpath teacher’s suggested approach
Account for All Non-Conservative Forces
  • On a rough surface with kinetic friction coefficient μ\mu, the net parallel force is ΣF∥=mgsin⁡θ−fk=mg(sin⁡θ−μcos⁡θ)\Sigma F_\parallel = m g \sin\theta - f_k = m g (\sin\theta - \mu \cos\theta).

  • Always draw a free-body diagram for each segment to confirm whether fk=μNf_k = \mu N must be subtracted from the driving gravitational component.

CORRECTED PATH
ACEpath Teacher's Demonstration
  1. Calculate the effective acceleration down the ramp: a1=g(sin⁡30.0∘−μ1cos⁡30.0∘)=9.80(0.500−0.200⋅0.8660)=9.80(0.3268)≈3.203 m/s2a_1 = g(\sin 30.0^\circ - \mu_1 \cos 30.0^\circ) = 9.80(0.500 - 0.200 \cdot 0.8660) = 9.80(0.3268) \approx 3.203\text{ m/s}^2.

  2. Find the correct arrival velocity at the bottom: v12=2a1s1=2(3.203)(8.00)≈51.24 m2/s2  ⟹  v1≈7.17 m/sv_1^2 = 2 a_1 s_1 = 2(3.203)(8.00) \approx 51.24\text{ m}^2/\text{s}^2 \implies v_1 \approx 7.17\text{ m/s}.

  3. Determine the stopping distance on the horizontal track: s2=v122μ2g=51.242(0.400)(9.80)=51.247.84≈6.55 ms_2 = \frac{v_1^2}{2 \mu_2 g} = \frac{51.24}{2(0.400)(9.80)} = \frac{51.24}{7.84} \approx 6.55\text{ m}.

Final answer

v1≈7.17 m/sv_1 \approx 7.17\text{ m/s} and s2≈6.55 ms_2 \approx 6.55\text{ m}; both constraints are satisfied (v1≤9.00 m/sv_1 \le 9.00\text{ m/s} and s2≤12.0 ms_2 \le 12.0\text{ m}).

NEXT STEPS
Final Takeaways from Your Teacher
  • Include non-conservative work terms (Wnc=−fksW_{\text{nc}} = -f_k s) whenever a surface specifies μ>0\mu > 0.

  • Check that N=mgcos⁡θN = m g \cos\theta on an incline so that fk=μmgcos⁡θf_k = \mu m g \cos\theta is correctly calculated before summing work.

OverviewACEpath Teacher's Diagnosis

03 A student omits the factor of 2 in the kinetic energy formula (1/2)*m*v², leading to halved squared velocity terms and halved stopping distance.

Sample Student Work

Reviewed by ACEpath Teacher
Step-by-Step Review
Walk Through It with Your Teacher
Incorrect
  1. Step 1

    m⋅g⋅s1⋅sin⁡(θ)−μ1⋅m⋅g⋅cos⁡(θ)⋅s1=m⋅v12  ⟹  v12=g⋅s1⋅(sin⁡(30.0∘)−0.200⋅cos⁡(30.0∘))  ⟹  v12=9.80⋅8.00⋅(0.500−0.1732)=25.62 m2/s2  ⟹  v1=5.06 m/sm \cdot g \cdot s_1 \cdot \sin(\theta) - \mu_1 \cdot m \cdot g \cdot \cos(\theta) \cdot s_1 = m \cdot v_1^2 \implies v_1^2 = g \cdot s_1 \cdot (\sin(30.0^\circ) - 0.200 \cdot \cos(30.0^\circ)) \implies v_1^2 = 9.80 \cdot 8.00 \cdot (0.500 - 0.1732) = 25.62\text{ m}^2/\text{s}^2 \implies v_1 = 5.06\text{ m/s}

    Correct

    Wnet=12mv12  ⟹  mgs1(sin⁡θ−μ1cos⁡θ)=12mv12  ⟹  v1=2gs1(sin⁡θ−μ1cos⁡θ)≈7.17 m/sW_{\text{net}} = \frac{1}{2}m v_1^2 \implies m g s_1(\sin\theta - \mu_1 \cos\theta) = \frac{1}{2}m v_1^2 \implies v_1 = \sqrt{2 g s_1(\sin\theta - \mu_1 \cos\theta)} \approx 7.17\text{ m/s}

    You correctly identified the components of gravity and kinetic friction along the incline, but you wrote the final kinetic energy as mv12m v_1^2 instead of 12mv12\frac{1}{2}m v_1^2. Missing the factor of 12\frac{1}{2} causes v12v_1^2 to be halved, yielding v1≈5.06 m/sv_1 \approx 5.06\text{ m/s} instead of 7.17 m/s7.17\text{ m/s}.

  2. Step 2

    −μ2⋅m⋅g⋅s2=0−m⋅v12  ⟹  s2=v12μ2⋅g=25.620.400⋅9.80=6.54 m-\mu_2 \cdot m \cdot g \cdot s_2 = 0 - m \cdot v_1^2 \implies s_2 = \frac{v_1^2}{\mu_2 \cdot g} = \frac{25.62}{0.400 \cdot 9.80} = 6.54\text{ m}

    Correct

    Wnet=ΔK  ⟹  −μ2mgs2=0−12mv12  ⟹  s2=v122μ2g=(7.17)22(0.400)(9.80)≈6.55 mW_{\text{net}} = \Delta K \implies -\mu_2 m g s_2 = 0 - \frac{1}{2}m v_1^2 \implies s_2 = \frac{v_1^2}{2\mu_2 g} = \frac{(7.17)^2}{2(0.400)(9.80)} \approx 6.55\text{ m}

    You repeated the kinetic energy omission here by writing ΔK=0−mv12\Delta K = 0 - m v_1^2 instead of 0−12mv120 - \frac{1}{2}m v_1^2. Because both v12v_1^2 and the denominator were missing a factor of 22, the errors canceled algebraically to give a stopping distance close to 6.55 m6.55\text{ m}, but the governing formula s2=v12μ2gs_2 = \frac{v_1^2}{\mu_2 g} is incorrect.

  3. Step 3

    v1=5.06 m/s≤9.00 m/s,  s2=6.54 m≤12.0 m  ⟹  The design complies with both safety constraints.v_1 = 5.06\text{ m/s} \le 9.00\text{ m/s},\; s_2 = 6.54\text{ m} \le 12.0\text{ m} \implies \text{The design complies with both safety constraints.}

    Correct

    v1=7.17 m/s≤9.00 m/s,  s2=6.55 m≤12.0 m  ⟹  Both design safety constraints are satisfied.v_1 = 7.17\text{ m/s} \le 9.00\text{ m/s},\; s_2 = 6.55\text{ m} \le 12.0\text{ m} \implies \text{Both design safety constraints are satisfied.}

    Your final qualitative conclusion is correct, but your constraint check for v1v_1 relies on the incorrect value from Step 1.

WHAT YOU DID WELL
Compliments from Your Teacher

You resolved the gravitational and normal forces on the incline correctly.

You correctly expressed the work done by friction over both displacements.

You recognized that mass cancels out in both energy balance equations.

THE ERROR
Where Your ACEpath Teacher Spotted the Mistake
Kinetic energy definition omission

You omitted the coefficient 1/2 from the kinetic energy formula, writing K = m*v^2 instead of K = (1/2)mv^2.

WHY IT HAPPENED
ACEpath Teacher's Diagnosis

You conflated momentum or a generic quadratic velocity term with kinetic energy, omitting the indispensable factor of 1/2 that arises from integrating work (W = ∫ m v dv = (1/2) m v²).

REASONING PATH
Your ACEpath teacher’s suggested approach
Kinetic Energy Definition
  • Translational kinetic energy is defined as K=12mv2K = \frac{1}{2} m v^2, not mv2m v^2.

  • Always verify that your kinetic energy terms contain the 12\frac{1}{2} multiplier before canceling or solving for velocity.

Dimensional and Integral Check
  • Work is the integral of force over displacement: W=∫ma ds=∫mv dv=12mv2W = \int m a\,ds = \int m v\,dv = \frac{1}{2}mv^2.

  • Check that the work-energy theorem reads Wnet=12mvf2−12mvi2W_{\text{net}} = \frac{1}{2}m v_f^2 - \frac{1}{2}m v_i^2.

CORRECTED PATH
ACEpath Teacher's Demonstration
  1. Apply the work-energy theorem on the incline: Wnet=(mgsin⁡30.0∘−μ1mgcos⁡30.0∘)s1=12mv12W_{\text{net}} = (m g \sin 30.0^\circ - \mu_1 m g \cos 30.0^\circ) s_1 = \frac{1}{2} m v_1^2.

  2. Solve for v1v_1: v1=2gs1(sin⁡30.0∘−μ1cos⁡30.0∘)=2(9.80)(8.00)(0.500−0.200×0.866)≈7.17 m/sv_1 = \sqrt{2 g s_1 (\sin 30.0^\circ - \mu_1 \cos 30.0^\circ)} = \sqrt{2(9.80)(8.00)(0.500 - 0.200 \times 0.866)} \approx 7.17\text{ m/s}.

  3. Apply the work-energy theorem on the horizontal deceleration track: −μ2mgs2=0−12mv12  ⟹  s2=v122μ2g-\mu_2 m g s_2 = 0 - \frac{1}{2} m v_1^2 \implies s_2 = \frac{v_1^2}{2 \mu_2 g}.

  4. Substitute v1=7.17 m/sv_1 = 7.17\text{ m/s}: s2=(7.17)22(0.400)(9.80)≈6.55 ms_2 = \frac{(7.17)^2}{2(0.400)(9.80)} \approx 6.55\text{ m}.

Final answer

v1≈7.17 m/sv_1 \approx 7.17\text{ m/s}, s2≈6.55 ms_2 \approx 6.55\text{ m}; both safety constraints are satisfied since v1≤9.00 m/sv_1 \le 9.00\text{ m/s} and s2≤12.0 ms_2 \le 12.0\text{ m}.

NEXT STEPS
Final Takeaways from Your Teacher
  • Review the formal derivation of the work-energy theorem ΔK=Wnet\Delta K = W_{\text{net}} to anchor why 12\frac{1}{2} is required.

  • Practice setting up ΔK\Delta K explicitly as 12mvf2−12mvi2\frac{1}{2}m v_f^2 - \frac{1}{2}m v_i^2 before substituting numerical values.

  • Solve problems combining incline dynamics with flat braking zones using proper energy balances.

Lock it in

Similar question

01

A 10.0 kg10.0\text{ kg} crate slides from rest down a 6.00 m6.00\text{ m} ramp inclined at 37.0∘37.0^\circ with μ=0.250\mu = 0.250. Using g=9.80 m/s2g = 9.80\text{ m/s}^2, sin⁡37.0∘=0.602\sin 37.0^\circ = 0.602, and cos⁡37.0∘=0.799\cos 37.0^\circ = 0.799, find the speed at the bottom of the ramp.

Answer

v=2gs(sin⁡θ−μcos⁡θ)=2(9.80)(6.00)(0.602−0.250×0.799)=117.6(0.402)≈6.88 m/sv = \sqrt{2gs(\sin\theta - \mu\cos\theta)} = \sqrt{2(9.80)(6.00)(0.602 - 0.250 \times 0.799)} = \sqrt{117.6(0.402)} \approx 6.88\text{ m/s}.

02

A skier enters a horizontal snow patch of length d=15.0 md = 15.0\text{ m} at speed v0=12.0 m/sv_0 = 12.0\text{ m/s}. The coefficient of kinetic friction is μk=0.180\mu_k = 0.180. Determine the skier's speed when exiting the snow patch, assuming g=9.80 m/s2g = 9.80\text{ m/s}^2.

Answer

Using vf2=v02−2μkgdv_f^2 = v_0^2 - 2\mu_k g d: vf2=12.02−2(0.180)(9.80)(15.0)=144−52.92=91.08 m2/s2v_f^2 = 12.0^2 - 2(0.180)(9.80)(15.0) = 144 - 52.92 = 91.08\text{ m}^2/\text{s}^2, so vf=91.08≈9.54 m/sv_f = \sqrt{91.08} \approx 9.54\text{ m/s}.

03

A cart starts from rest at the top of an incline of length s1=10.0 ms_1 = 10.0\text{ m} and angle θ=30.0∘\theta = 30.0^\circ with μ1=0.150\mu_1 = 0.150. It then transitions to a horizontal surface with μ2=0.500\mu_2 = 0.500. Express the total horizontal stopping distance s2s_2 in terms of s1,θ,μ1s_1, \theta, \mu_1, and μ2\mu_2, then compute its numerical value for g=9.80 m/s2g = 9.80\text{ m/s}^2.

Answer

By conservation of energy over the entire motion, mgs1(sin⁡θ−μ1cos⁡θ)=μ2mgs2mg s_1(\sin\theta - \mu_1\cos\theta) = \mu_2 mg s_2, giving s2=s1sin⁡θ−μ1cos⁡θμ2s_2 = s_1\frac{\sin\theta - \mu_1\cos\theta}{\mu_2}. Substituting values: s2=10.0×0.500−0.150(0.866)0.500=10.0×0.37010.500≈7.40 ms_2 = 10.0 \times \frac{0.500 - 0.150(0.866)}{0.500} = 10.0 \times \frac{0.3701}{0.500} \approx 7.40\text{ m}.

Loading workspace…