Resources
A pharmacokinetics laboratory monitors drug plasma concentration following intravenous injection. Sampling occurs at non-standard time intervals with mixed concentration units: at , ; at , ; at , ; at , ; and at , . First convert all times to hours and all concentrations to standard SI units of (). Then, determine whether the elimination follows a zero-order (linear) or first-order (exponential) model based on unit-standardized rate characteristics, and calculate the elimination half-life in hours.
Answer and steps
Final answer
Standardized concentrations: at , at , at , at , at (noting ); Model type: First-order exponential decay; Elimination half-life: ; Model equation:
Steps
Unit Conversions
Convert each sampling time from minutes to hours using the conversion factor :
Convert all concentrations to the standard SI-derived unit . Since and , we have:
For the measurement at , convert from micrograms per liter ():
The unit-standardized data points are:
Determine Model Type (Zero-Order vs. First-Order)
-
Zero-Order Model (Linear Decay): The rate of elimination is constant, meaning the concentration drops by an equal amount per unit time: Examining equal intervals of :
- From to :
- From to :
Since the absolute decrease is not constant, the process is not zero-order.
- First-Order Model (Exponential Decay): The rate of elimination is proportional to the concentration, meaning the ratio between successive values over equal time intervals is constant:
Because a constant fraction of the drug is eliminated every , the elimination follows a first-order exponential decay model.
Determine Elimination Half-Life and Model Equation
The half-life is the time required for the concentration to decrease to half of its initial value:
From the standardized data, at . Therefore:
The general first-order decay equation parameterized by half-life is:
Substituting and gives:
Typical errors
01 A student incorrectly assumes zero-order kinetics by evaluating only the first time interval's absolute drop and expecting a linear decrease.
Sample Student Work
Reviewed by ACEpath TeacherStep-by-Step Review
Walk Through It with Your Teacher- Step 1
- Step 2Correct
,
You calculated the slope over only the first interval and assumed the rate remains constant. A zero-order model requires the difference to be constant across all equal time steps, but here drops from to . Instead, the ratio between consecutive points is constant (), which signifies first-order exponential decay.
- Step 3Correct
Because you selected a zero-order model, you used the zero-order half-life formula . For first-order decay, the half-life is constant and can be read directly from the data as the time when concentration drops from to , which is .
WHAT YOU DID WELL
Compliments from Your TeacherYou accurately converted all non-standard time and concentration units into hours and .
You set up a clear rate calculation using the initial change in concentration over time.
THE ERROR
Where Your ACEpath Teacher Spotted the Mistakenone
WHY IT HAPPENED
ACEpath Teacher's DiagnosisYou evaluated the absolute drop across only the initial interval and concluded the rate was constant without checking whether subsequent intervals exhibited constant differences (zero-order) or constant ratios (first-order).
REASONING PATH
Your ACEpath teacher’s suggested approach- Rule of Constant Difference vs. Constant Ratio
For equally spaced time intervals, zero-order kinetics displays equal absolute changes (), whereas first-order kinetics displays equal ratios ().
Calculate at least two consecutive intervals to check whether or the ratio remains constant before picking a model.
- Reading Half-Life from Tabular Data
Half-life is the elapsed time for concentration to reach .
Look for in your standardized table to identify directly without extra formulas.
CORRECTED PATH
ACEpath Teacher's DemonstrationCompute the ratio for consecutive equal time steps (): , , .
Since the ratio is constant, classify the kinetics as first-order exponential decay.
Identify the time when concentration halves from to , which occurs at .
Model type: First-order exponential decay; Elimination half-life:
02 A student misidentifies the half-life by reading the time required for the concentration to drop by the first interval rather than to half of its initial value.
Sample Student Work
Reviewed by ACEpath TeacherStep-by-Step Review
Walk Through It with Your Teacher- Step 1
- Step 2
- Step 3Correct
The half-life is defined as the time it takes for the concentration to reduce to of its baseline value (), not the time of the first measurement step ().
WHAT YOU DID WELL
Compliments from Your TeacherYou converted the sampling times and concentrations into standard SI-derived units correctly.
You evaluated the ratio of consecutive concentration values to verify first-order kinetics.
THE ERROR
Where Your ACEpath Teacher Spotted the Mistakeno
WHY IT HAPPENED
ACEpath Teacher's DiagnosisYou conflated the duration of a single sampling step () with the elimination half-life (), setting equal to the timestamp of the first observed decline instead of solving for the time when .
REASONING PATH
Your ACEpath teacher’s suggested approach- Definition of Half-Life
For exponential decay , the half-life satisfies .
Always find half of the initial concentration first (here, ) and read the corresponding time from the data or solve for .
CORRECTED PATH
ACEpath Teacher's DemonstrationIdentify the initial concentration at : .
Determine the target concentration for one half-life: .
Locate in your standardized data: this concentration occurs at .
Lock it in
How do you distinguish zero-order decay from first-order decay using data over equal time intervals ?
Zero-order decay has a constant absolute difference (), while first-order decay has a constant quotient or ratio ().
Similar question
A substance has plasma concentration values at equal 1-hour intervals: , , and . Determine whether this follows zero-order or first-order elimination, and state the elimination rate constant .
Answer
Zero-order elimination. The absolute change over each 1-hour step is constant: and . The elimination rate constant is .
A drug monitored at , , and shows concentrations of , , and respectively. Identify the elimination model type, state the half-life , and write the model equation .
Answer
First-order exponential decay. The concentration drops by a factor of every . Thus, , and the model equation is .
An intravenous tracer is measured at with , at with , and at with . Convert times to hours, confirm whether the data fits a first-order elimination model, and find the concentration at .
Answer
Times in hours: , , and . From to , concentration halves (), giving . Over the next ( half-lives), it halves twice (), confirming first-order kinetics. At ( half-lives), .