Resources

An engineering calibration model uses the base response curve R(t)=11+t2R(t) = \frac{1}{1 + t^2}, where tt is measured in milliseconds (ms\text{ms}) and RR is in volts (V\text{V}). A revised sensor setup requires time to be input in microseconds (μs\mu\text{s}, where 1 ms=1000 μs1\text{ ms} = 1000\text{ }\mu\text{s}) and outputs response in millivolts (mV\text{mV}, where 1 V=1000 mV1\text{ V} = 1000\text{ mV}), along with a delay offset of 250 μs250\text{ }\mu\text{s} and a steady baseline offset of +50 mV+50\text{ mV}. Express the transformed function S(τ)S(\tau) in terms of τ\tau (in μs\mu\text{s}) with output in mV\text{mV}, and compute S(250)S(250).

Answer and steps

Final answer

S(τ)=10001+(τ−2501000)2+50S(\tau) = \frac{1000}{1 + \left(\frac{\tau - 250}{1000}\right)^2} + 50 (in mV\text{mV}); S(250)=1050 mVS(250) = 1050\text{ mV}

Steps

01

Relate the New Input Variable τ\tau to the Original Input tt

The original input tt is measured in milliseconds (ms\text{ms}), while the new input τ\tau is measured in microseconds (μs\mu\text{s}).

  1. Unit conversion: Since 1 ms=1000 μs1\text{ ms} = 1000\text{ }\mu\text{s}, any duration measured in microseconds must be divided by 10001000 to convert it to milliseconds.
  2. Time delay (horizontal shift): A delay of 250 μs250\text{ }\mu\text{s} means an event that originally occurred at t=0t = 0 now occurs at τ=250 μs\tau = 250\text{ }\mu\text{s}. Therefore, the delayed time in microseconds is τ−250\tau - 250.

Converting this delayed time into milliseconds gives the effective input for the base function: t=τ−2501000t = \frac{\tau - 250}{1000}

Common Pitfall: When combining horizontal shifts and scaling, ensure the shift is applied in the same unit as the input before or after scaling. Here, because the delay is specified as 250 μs250\text{ }\mu\text{s}, it subtracts directly from τ\tau inside the conversion fraction: τ−2501000\frac{\tau - 250}{1000}.


02

Apply the Output Transformations (Vertical Scaling and Shift)

The base function R(t)R(t) produces an output in volts (V\text{V}).

  1. Unit conversion (vertical stretch): Since 1 V=1000 mV1\text{ V} = 1000\text{ mV}, multiply the response by 10001000 to convert from volts to millivolts.
  2. Baseline offset (vertical shift): Adding a steady baseline of +50 mV+50\text{ mV} shifts the entire graph upward by 5050.

Combining the vertical transformations with the input substitution: S(τ)=1000⋅R(τ−2501000)+50S(\tau) = 1000 \cdot R\left(\frac{\tau - 250}{1000}\right) + 50

Substitute R(t)=11+t2R(t) = \frac{1}{1 + t^2}: S(τ)=10001+(τ−2501000)2+50S(\tau) = \frac{1000}{1 + \left(\frac{\tau - 250}{1000}\right)^2} + 50


03

Calculate S(250)S(250)

Evaluate the transformed function at τ=250 μs\tau = 250\text{ }\mu\text{s}: S(250)=10001+(250−2501000)2+50S(250) = \frac{1000}{1 + \left(\frac{250 - 250}{1000}\right)^2} + 50

Simplify the argument inside the fraction: S(250)=10001+02+50=10001+50=1050 mVS(250) = \frac{1000}{1 + 0^2} + 50 = \frac{1000}{1} + 50 = 1050\text{ mV}

Typical errors

OverviewACEpath Teacher's Diagnosis

01 The student multiplies by 1000 instead of dividing by 1000 when converting time from microseconds to milliseconds, resulting in 1000(τ - 250) in the input argument.

Sample Student Work

Reviewed by ACEpath Teacher
Step-by-Step Review
Walk Through It with Your Teacher
Partially correct
  1. Step 1

    t=1000(τ−250)t = 1000(\tau - 250)

    Correct

    t=τ−2501000t = \frac{\tau - 250}{1000}

    To convert from a smaller unit (microseconds) to a larger unit (milliseconds), you need to divide by 10001000, because 1 ms=1000 μs1\text{ ms} = 1000\text{ }\mu\text{s} means 1 μs=11000 ms1\text{ }\mu\text{s} = \frac{1}{1000}\text{ ms}.

  2. Step 2

    S(τ)=1000⋅R(t)+50  ⟹  S(τ)=10001+(1000(τ−250))2+50S(\tau) = 1000 \cdot R(t) + 50 \implies S(\tau) = \frac{1000}{1 + (1000(\tau - 250))^2} + 50

    Correct

    S(τ)=1000⋅R(τ−2501000)+50=10001+(τ−2501000)2+50S(\tau) = 1000 \cdot R\left(\frac{\tau - 250}{1000}\right) + 50 = \frac{1000}{1 + \left(\frac{\tau - 250}{1000}\right)^2} + 50

    Your vertical scaling by 10001000 and vertical shift of +50+50 are completely correct, but the function argument carries over the multiplication error from the first step.

  3. Step 3

    S(250)=10001+(1000(250−250))2+50  ⟹  S(250)=10001+50=1050S(250) = \frac{1000}{1 + (1000(250 - 250))^2} + 50 \implies S(250) = \frac{1000}{1} + 50 = 1050

    Correct

    S(250)=10001+(250−2501000)2+50=1050 mVS(250) = \frac{1000}{1 + \left(\frac{250 - 250}{1000}\right)^2} + 50 = 1050\text{ mV}

    Because 250−250=0250 - 250 = 0, both 1000(0)1000(0) and 01000\frac{0}{1000} evaluate to 00, so your arithmetic coincidentally led to the correct numerical value.

WHAT YOU DID WELL
Compliments from Your Teacher

You correctly applied the vertical stretch factor of 10001000 to convert volts to millivolts.

You correctly added the baseline offset of +50 mV+50\text{ mV} as an outside vertical shift.

You correctly identified that a time delay of 250 μs250\text{ }\mu\text{s} corresponds to shifting by τ−250\tau - 250.

THE ERROR
Where Your ACEpath Teacher Spotted the Mistake
Input Unit Scaling Inversion

no

WHY IT HAPPENED
ACEpath Teacher's Diagnosis

You inverted the unit conversion factor for the horizontal input variable, multiplying by 10001000 rather than dividing by 10001000 to convert microseconds to milliseconds.

REASONING PATH
Your ACEpath teacher’s suggested approach
Unit Conversion Direction Check
  • When converting a quantity from a smaller unit to a larger unit, divide by the conversion factor: value in large unit=value in small unitfactor\text{value in large unit} = \frac{\text{value in small unit}}{\text{factor}}.

  • Check dimensional units explicitly: τ μs×1 ms1000 μs=τ1000 ms\tau\text{ }\mu\text{s} \times \frac{1\text{ ms}}{1000\text{ }\mu\text{s}} = \frac{\tau}{1000}\text{ ms}.

CORRECTED PATH
ACEpath Teacher's Demonstration
  1. Express the original time variable tt (in ms\text{ms}) in terms of the new input τ\tau (in μs\mu\text{s}): t=τ−2501000t = \frac{\tau - 250}{1000}.

  2. Substitute this expression into the vertically scaled and shifted response function: S(τ)=1000⋅R(t)+50=10001+(τ−2501000)2+50S(\tau) = 1000 \cdot R(t) + 50 = \frac{1000}{1 + \left(\frac{\tau - 250}{1000}\right)^2} + 50.

  3. Evaluate at τ=250 μs\tau = 250\text{ }\mu\text{s}: S(250)=10001+02+50=1050 mVS(250) = \frac{1000}{1 + 0^2} + 50 = 1050\text{ mV}.

Final answer

S(τ)=10001+(τ−2501000)2+50 mVS(\tau) = \frac{1000}{1 + \left(\frac{\tau - 250}{1000}\right)^2} + 50\text{ mV}; S(250)=1050 mVS(250) = 1050\text{ mV}

NEXT STEPS
Final Takeaways from Your Teacher
  • Always write out the dimensional analysis fraction (e.g., 1 ms1000 μs\frac{1\text{ ms}}{1000\text{ }\mu\text{s}}) when changing units inside a function argument.

  • Double-check your transformed formula by testing a non-zero test value such as τ=1250 μs\tau = 1250\text{ }\mu\text{s}, which should correspond to t=1 mst = 1\text{ ms}.

OverviewACEpath Teacher's Diagnosis

02 The student treats the delay offset as an advance and writes (τ + 250) instead of (τ - 250).

Sample Student Work

Reviewed by ACEpath Teacher
Step-by-Step Review
Walk Through It with Your Teacher
Incorrect
  1. Step 1

    t=τ+2501000t = \frac{\tau + 250}{1000}

    Correct

    t=τ−2501000t = \frac{\tau - 250}{1000}

    A time delay of 250 μs250\text{ }\mu\text{s} means an event originally at t=0t = 0 now happens later at τ=250 μs\tau = 250\text{ }\mu\text{s}. This requires a rightward horizontal shift of τ−250\tau - 250, not an advance of τ+250\tau + 250.

  2. Step 2

    S(τ)=10001+(τ+2501000)2+50S(\tau) = \frac{1000}{1 + \left(\frac{\tau + 250}{1000}\right)^2} + 50

    Correct

    S(τ)=10001+(τ−2501000)2+50S(\tau) = \frac{1000}{1 + \left(\frac{\tau - 250}{1000}\right)^2} + 50

    You correctly scaled the output by 10001000 to convert volts to millivolts and added the +50 mV+50\text{ mV} baseline offset, but the expression carries over the sign error from the input shift.

  3. Step 3

    S(250)=10001+(250+2501000)2+50  ⟹  S(250)=10001+(500/1000)2+50  ⟹  S(250)=10001+0.25+50=800+50=850S(250) = \frac{1000}{1 + \left(\frac{250 + 250}{1000}\right)^2} + 50 \implies S(250) = \frac{1000}{1 + (500/1000)^2} + 50 \implies S(250) = \frac{1000}{1 + 0.25} + 50 = 800 + 50 = 850

    Correct

    S(250)=10001+(250−2501000)2+50=1050 mVS(250) = \frac{1000}{1 + \left(\frac{250 - 250}{1000}\right)^2} + 50 = 1050\text{ mV}

    Your arithmetic and substitution were carried out accurately, but the evaluation reflects the earlier sign mistake in the time delay.

WHAT YOU DID WELL
Compliments from Your Teacher

You correctly divided τ\tau by 10001000 to convert microseconds to milliseconds.

You correctly multiplied the output by 10001000 to convert volts to millivolts.

You correctly added +50+50 to account for the steady baseline offset.

You performed the arithmetic substitution and evaluation without calculation slips.

THE ERROR
Where Your ACEpath Teacher Spotted the Mistake
Horizontal Shift Direction Error

no

WHY IT HAPPENED
ACEpath Teacher's Diagnosis

You confused a time delay (a shift to the right, requiring x−cx - c) with an advance (a shift to the left, requiring x+cx + c). In horizontal transformations, delaying an event means it occurs at a larger input value, so the argument must subtract the offset.

REASONING PATH
Your ACEpath teacher’s suggested approach
Anchor Point Test
  • For a delay of cc units, the peak or baseline event that occurred at t=0t = 0 must occur when the new variable equals cc.

  • Set your transformed input expression to zero: τ−250=0  ⟹  τ=250\tau - 250 = 0 \implies \tau = 250. Since τ=250\tau = 250 restores the original t=0t = 0 state, subtracting the delay is correct.

CORRECTED PATH
ACEpath Teacher's Demonstration
  1. Set the delayed time in microseconds: τ−250\tau - 250

  2. Convert microseconds to milliseconds: t=τ−2501000t = \frac{\tau - 250}{1000}

  3. Substitute tt into R(t)R(t) and apply vertical transformations: S(τ)=1000⋅R(τ−2501000)+50=10001+(τ−2501000)2+50S(\tau) = 1000 \cdot R\left(\frac{\tau - 250}{1000}\right) + 50 = \frac{1000}{1 + \left(\frac{\tau - 250}{1000}\right)^2} + 50

  4. Evaluate at τ=250\tau = 250: S(250)=10001+02+50=1000+50=1050 mVS(250) = \frac{1000}{1 + 0^2} + 50 = 1000 + 50 = 1050\text{ mV}

Final answer

S(τ)=10001+(τ−2501000)2+50S(\tau) = \frac{1000}{1 + \left(\frac{\tau - 250}{1000}\right)^2} + 50, S(250)=1050 mVS(250) = 1050\text{ mV}

NEXT STEPS
Final Takeaways from Your Teacher
  • Always verify horizontal shifts by checking where the original feature at t=0t = 0 lands under your formula.

  • Practice pairing unit conversions with translations by applying the shift directly to the specific variable matching the shift's units.

OverviewACEpath Teacher's Diagnosis

03 The student forgets to scale the output of R(t) by 1000 to convert from volts to millivolts before adding the 50 mV baseline offset.

Sample Student Work

Reviewed by ACEpath Teacher
Step-by-Step Review
Walk Through It with Your Teacher
Partially correct
  1. Step 1

    t=τ−2501000t = \frac{\tau - 250}{1000}

  2. Step 2

    S(τ)=11+(τ−2501000)2+50S(\tau) = \frac{1}{1 + \left(\frac{\tau - 250}{1000}\right)^2} + 50

    Correct

    S(τ)=10001+(τ−2501000)2+50S(\tau) = \frac{1000}{1 + \left(\frac{\tau - 250}{1000}\right)^2} + 50

    The base function R(t)R(t) produces values in volts (V\text{V}), while the desired output and baseline offset are in millivolts (mV\text{mV}). You must multiply the base function by 10001000 before adding the 50 mV50\text{ mV} offset.

  3. Step 3

    S(250)=11+(250−2501000)2+50  ⟹  S(250)=11+0+50=51S(250) = \frac{1}{1 + \left(\frac{250 - 250}{1000}\right)^2} + 50 \implies S(250) = \frac{1}{1 + 0} + 50 = 51

    Correct

    S(250)=10001+0+50=1050 mVS(250) = \frac{1000}{1 + 0} + 50 = 1050\text{ mV}

    Your arithmetic evaluation followed correctly from your formula, but the result was altered by the missing factor of 10001000.

WHAT YOU DID WELL
Compliments from Your Teacher

You correctly shifted the time input by 250 μs250\text{ }\mu\text{s} to model the time delay.

You scaled the microsecond input to milliseconds using the correct conversion factor of 1000 μs/ms1000\text{ }\mu\text{s}/\text{ms}.

You accurately substituted the shifted variable into the rational function and evaluated the baseline arithmetic.

THE ERROR
Where Your ACEpath Teacher Spotted the Mistake
Missing vertical scale factor (unit mismatch between output and offset)

You treated the output of R(t)R(t) as if it were already in millivolts when adding +50 mV+50\text{ mV}.

WHY IT HAPPENED
ACEpath Teacher's Diagnosis

Overlooking the unit change on the dependent variable (yy-axis). When an original function outputs in volts and the requested function outputs in millivolts, a vertical stretch factor of 10001000 must be applied before adding an offset specified in millivolts.

REASONING PATH
Your ACEpath teacher’s suggested approach
Match Units Across Terms
  • Every additive term in a model must have identical physical units.

  • Check the units of R(t)R(t) (volts) and the offset (millivolts). Scale R(t)R(t) by 1000 mV/V1000\text{ mV}/\text{V} before adding +50 mV+50\text{ mV}.

Apply Vertical Transformations from Inside Out
  • For a vertical unit change and vertical shift, ynew=c⋅yold+dy_{\text{new}} = c \cdot y_{\text{old}} + d.

  • Multiply the entire base response by 10001000 first, then add 5050 to give S(τ)=1000⋅R(t)+50S(\tau) = 1000 \cdot R(t) + 50.

CORRECTED PATH
ACEpath Teacher's Demonstration
  1. Convert the base response from volts to millivolts: 1000⋅R(t)=10001+t21000 \cdot R(t) = \frac{1000}{1 + t^2}.

  2. Add the baseline offset of +50 mV+50\text{ mV}: S(τ)=10001+(τ−2501000)2+50S(\tau) = \frac{1000}{1 + \left(\frac{\tau - 250}{1000}\right)^2} + 50.

  3. Evaluate at τ=250 μs\tau = 250\text{ }\mu\text{s}: S(250)=10001+0+50=1050 mVS(250) = \frac{1000}{1 + 0} + 50 = 1050\text{ mV}.

Final answer

S(τ)=10001+(τ−2501000)2+50 mVS(\tau) = \frac{1000}{1 + \left(\frac{\tau - 250}{1000}\right)^2} + 50\text{ mV}, and S(250)=1050 mVS(250) = 1050\text{ mV}

NEXT STEPS
Final Takeaways from Your Teacher
  • Annotate the units of each parameter and variable directly on your equation before combining them.

  • Practice identifying whether a unit conversion affects the input (horizontal stretch/compression) or the output (vertical stretch/compression).

  • Perform a quick dimensional sanity check to confirm that all terms added together share the same unit.

Lock it in

Similar question

01

A temperature decay model is given by T(t)=80e−0.2tT(t) = 80 e^{-0.2 t}, where tt is in hours. Write the model as a function of time mm measured in minutes, where 1 hour=60 minutes1\text{ hour} = 60\text{ minutes}.

Answer

Since t=m60t = \frac{m}{60}, substituting gives T(m)=80e−0.2(m60)=80e−m300T(m) = 80 e^{-0.2 \left(\frac{m}{60}\right)} = 80 e^{-\frac{m}{300}}.

02

The height of a projectile is modeled by h(t)=20−5t2h(t) = 20 - 5t^2, with tt in seconds and hh in meters. A sensor records time uu in tenths of a second (1 s=10 ds1\text{ s} = 10\text{ ds}) and requires an advance of 3 ds3\text{ ds} (meaning the event starts at u=−3 dsu = -3\text{ ds}). Express the height function H(u)H(u) in terms of uu.

Answer

An advance of 3 ds3\text{ ds} shifts time to u+3u + 3. Converting tenths of a second to seconds requires dividing by 1010, so t=u+310t = \frac{u + 3}{10}. Thus, H(u)=20−5(u+310)2=20−(u+3)220H(u) = 20 - 5\left(\frac{u + 3}{10}\right)^2 = 20 - \frac{(u + 3)^2}{20}.

03

A signal filter has gain G(f)=11+f2G(f) = \frac{1}{\sqrt{1 + f^2}}, where frequency ff is in megahertz (MHz\text{MHz}). A digital processor inputs frequency ν\nu in kilohertz (kHz\text{kHz}, where 1 MHz=1000 kHz1\text{ MHz} = 1000\text{ kHz}) with a frequency shift offset of +400 kHz+400\text{ kHz}, and amplifies the output by a factor of 55. Find the transformed gain function K(ν)K(\nu) and calculate K(600)K(600).

Answer

The effective frequency in MHz\text{MHz} is f=ν−4001000f = \frac{\nu - 400}{1000}. Applying the vertical amplification gives K(ν)=51+(ν−4001000)2K(\nu) = \frac{5}{\sqrt{1 + \left(\frac{\nu - 400}{1000}\right)^2}}. Evaluating at ν=600\nu = 600 gives f=600−4001000=0.2f = \frac{600 - 400}{1000} = 0.2, so K(600)=51+0.22=51.04=2526≈4.90K(600) = \frac{5}{\sqrt{1 + 0.2^2}} = \frac{5}{\sqrt{1.04}} = \frac{25}{\sqrt{26}} \approx 4.90.

Loading workspace…