Resources

A biochemical engineer models the cooling of a heated cylindrical bioreactor vessel using Newton's Law of Cooling: dTdt=−k(T−Tenv)\frac{dT}{dt} = -k(T - T_{\text{env}}), where T(t)T(t) is the core temperature of the vessel, Tenv=20.0∘CT_{\text{env}} = 20.0^\circ\text{C} is the surrounding ambient temperature, and k=0.0500 min−1k = 0.0500\text{ min}^{-1}. (a) State the critical thermodynamic assumption regarding internal temperature gradients inside the vessel required for this lumped-capacitance model to be valid. (b) If the lumped-capacitance criterion requires the dimensionless Biot number to satisfy Bi=hLcκ<0.100\text{Bi} = \frac{h L_c}{\kappa} < 0.100, where h=15.0 W/(m2⋅K)h = 15.0\text{ W}/(\text{m}^2\cdot\text{K}) is the convective heat transfer coefficient and characteristic length Lc=0.0400 mL_c = 0.0400\text{ m}, calculate the minimum thermal conductivity κmin⁡\kappa_{\min} of the vessel material required to prevent the model from failing at this threshold boundary.

Answer and steps

Final answer

(a) The model assumes a negligible internal temperature gradient throughout the vessel's volume (infinite internal thermal conductivity relative to surface convection), meaning the temperature T(t)T(t) is spatially uniform across the entire core at any given instant. (b) Setting Bi=hLcκmin⁡=0.100\text{Bi} = \frac{h L_c}{\kappa_{\min}} = 0.100 yields κmin⁡=(15.0 W/(m2⋅K))(0.0400 m)0.100=6.00 W/(m⋅K)\kappa_{\min} = \frac{(15.0\text{ W}/(\text{m}^2\cdot\text{K}))(0.0400\text{ m})}{0.100} = 6.00\text{ W}/(\text{m}\cdot\text{K}).

Steps

Part (a): Identifying the Lumped-Capacitance Assumption

Newton's Law of Cooling represents the system with an ordinary differential equation involving a single time-dependent temperature T(t)T(t): dTdt=−k(T−Tenv)\frac{dT}{dt} = -k(T - T_{\text{env}})

  1. Physical Meaning: Because the temperature TT depends only on time tt and not on spatial coordinates (r,θ,z)(r, \theta, z), the model assumes that heat conducts rapidly through the interior of the vessel compared to the rate at which heat is lost from the surface to the environment.
  2. Core Assumption: The internal temperature gradient within the vessel is negligible (∇T≈0\nabla T \approx 0). In other words, the material's internal conductive thermal resistance is much smaller than the external convective thermal resistance, meaning the temperature distribution throughout the core volume remains spatially uniform at every instant.

Pitfall: Assuming that Newton's Law of Cooling applies to any cooling object without checking internal conduction is a common error. When internal temperature gradients are significant, a partial differential equation (the heat conduction equation) must be used instead.


Part (b): Calculating the Minimum Thermal Conductivity κmin⁡\kappa_{\min}

The lumped-capacitance approach is generally considered accurate when the dimensionless Biot number satisfies: Bi=hLcκ<0.100\text{Bi} = \frac{h L_c}{\kappa} < 0.100

where:

  • h=15.0 W/(m2⋅K)h = 15.0\text{ W}/(\text{m}^2\cdot\text{K}) is the convective heat transfer coefficient.
  • Lc=0.0400 mL_c = 0.0400\text{ m} is the characteristic length.
  • κ\kappa is the thermal conductivity of the material.
  1. Set up the boundary equation: At the validity threshold Bi=0.100\text{Bi} = 0.100, we solve for the boundary value κmin⁡\kappa_{\min}: hLcκmin⁡=0.100\frac{h L_c}{\kappa_{\min}} = 0.100
  2. Rearrange for κmin⁡\kappa_{\min}: κmin⁡=hLc0.100\kappa_{\min} = \frac{h L_c}{0.100}
  3. Substitute the given values: κmin⁡=(15.0 W/(m2⋅K))⋅(0.0400 m)0.100\kappa_{\min} = \frac{(15.0\text{ W}/(\text{m}^2\cdot\text{K})) \cdot (0.0400\text{ m})}{0.100} κmin⁡=0.6000.100=6.00 W/(m⋅K)\kappa_{\min} = \frac{0.600}{0.100} = 6.00\text{ W}/(\text{m}\cdot\text{K})

Thus, the vessel material must have a thermal conductivity of at least 6.00 W/(m⋅K)6.00\text{ W}/(\text{m}\cdot\text{K}) for the lumped-capacitance model to remain valid at this boundary.

Typical errors

OverviewACEpath Teacher's Diagnosis

01 The student confuses the Biot number formula by inverting the ratio of convective to conductive resistance as κ / (h · Lc).

Sample Student Work

Reviewed by ACEpath Teacher
Step-by-Step Review
Walk Through It with Your Teacher
Partially correct
  1. Step 1

    The temperature inside the vessel is uniform with negligible internal temperature gradients.

  2. Step 2

    Bi=Kh⋅Lc<0.100\text{Bi} = \frac{K}{h \cdot L_c} < 0.100

    Correct

    Bi=hLcκ<0.100\text{Bi} = \frac{h L_c}{\kappa} < 0.100

    You inverted the Biot number ratio. The Biot number is defined as Bi=hLcκ\text{Bi} = \frac{h L_c}{\kappa}, representing the ratio of internal conduction resistance to external convection resistance.

  3. Step 3

    Kmin⁡=0.100⋅h⋅Lc  ⟹  Kmin⁡=0.100⋅15.0⋅0.0400=0.0600 W/(m⋅K)K_{\min} = 0.100 \cdot h \cdot L_c \implies K_{\min} = 0.100 \cdot 15.0 \cdot 0.0400 = 0.0600\text{ W}/(\text{m}\cdot\text{K})

    Correct

    κmin⁡=hLc0.100=15.0⋅0.04000.100=6.00 W/(m⋅K)\kappa_{\min} = \frac{h L_c}{0.100} = \frac{15.0 \cdot 0.0400}{0.100} = 6.00\text{ W}/(\text{m}\cdot\text{K})

    Because your setup inverted the relationship between κ\kappa and Bi\text{Bi}, your algebraic rearrangement led to κmin⁡=0.100⋅hLc\kappa_{\min} = 0.100 \cdot h L_c instead of hLc0.100\frac{h L_c}{0.100}.

WHAT YOU DID WELL
Compliments from Your Teacher

You clearly articulated the spatial uniformity assumption required for lumped thermal modeling.

You performed clean arithmetic substitution using the given numerical parameters.

THE ERROR
Where Your ACEpath Teacher Spotted the Mistake
Inverted Biot Number Definition

none

WHY IT HAPPENED
ACEpath Teacher's Diagnosis

You recalled or set up the Biot number as the ratio of conductivity to convective parameters (κhLc)(\frac{\kappa}{h L_c}) rather than convection to conduction (hLcκ)(\frac{h L_c}{\kappa}).

REASONING PATH
Your ACEpath teacher’s suggested approach
Biot Number as a Ratio of Resistances
  • Bi=Internal Conduction ResistanceExternal Convection Resistance=Lc/κ1/h=hLcκ\text{Bi} = \frac{\text{Internal Conduction Resistance}}{\text{External Convection Resistance}} = \frac{L_c / \kappa}{1 / h} = \frac{h L_c}{\kappa}

  • Always verify that higher thermal conductivity κ\kappa decreases Bi\text{Bi} (making the internal temperature more uniform).

CORRECTED PATH
ACEpath Teacher's Demonstration
  1. Set up the threshold boundary equation using the correct Biot definition: hLcκmin⁡=0.100\frac{h L_c}{\kappa_{\min}} = 0.100.

  2. Solve for κmin⁡\kappa_{\min} by isolating the denominator: κmin⁡=hLc0.100\kappa_{\min} = \frac{h L_c}{0.100}.

  3. Substitute the given values: κmin⁡=15.0 W/(m2⋅K)×0.0400 m0.100=0.6000.100=6.00 W/(m⋅K)\kappa_{\min} = \frac{15.0\text{ W}/(\text{m}^2\cdot\text{K}) \times 0.0400\text{ m}}{0.100} = \frac{0.600}{0.100} = 6.00\text{ W}/(\text{m}\cdot\text{K}).

Final answer

κmin⁡=6.00 W/(m⋅K)\kappa_{\min} = 6.00\text{ W}/(\text{m}\cdot\text{K})

NEXT STEPS
Final Takeaways from Your Teacher
  • Check that your physical variables make intuitive sense: a more conductive material (larger κ\kappa) should lead to smaller temperature gradients and therefore a smaller Biot number.

  • Reread given formulas carefully from the problem statement before writing down initial algebraic equations.

OverviewACEpath Teacher's Diagnosis

02 The student misinterprets the lumped-capacitance criterion as Bi > 0.100 rather than Bi < 0.100, resulting in an inverted algebraic inequality.

Sample Student Work

Reviewed by ACEpath Teacher
Step-by-Step Review
Walk Through It with Your Teacher
Partially correct
  1. Step 1

    Negligible thermal resistance inside the body, so internal temperature gradients are negligible.

  2. Step 2

    Bi=h⋅Lcκ>0.100  ⟹  κ<h⋅Lc0.100\text{Bi} = \frac{h \cdot L_c}{\kappa} > 0.100 \implies \kappa < \frac{h \cdot L_c}{0.100}

    Correct

    Bi=hLcκ<0.100  ⟹  κ>hLc0.100\text{Bi} = \frac{h L_c}{\kappa} < 0.100 \implies \kappa > \frac{h L_c}{0.100}

    You wrote Bi>0.100\text{Bi} > 0.100 instead of Bi<0.100\text{Bi} < 0.100. For a lumped-capacitance model to be valid, internal conduction resistance must be much smaller than surface convection resistance, requiring Bi<0.100\text{Bi} < 0.100.

  3. Step 3

    κmax⁡=(15.0⋅0.0400)0.100=6.00 W/(m⋅K)  ⟹  κmin⁡ does not exist because κ can be arbitrarily small\kappa_{\max} = \frac{(15.0 \cdot 0.0400)}{0.100} = 6.00\text{ W}/(\text{m}\cdot\text{K}) \implies \kappa_{\min}\text{ does not exist because }\kappa\text{ can be arbitrarily small}

    Correct

    κmin⁡=(15.0 W/(m2⋅K))(0.0400 m)0.100=6.00 W/(m⋅K)\kappa_{\min} = \frac{(15.0\text{ W}/(\text{m}^2\cdot\text{K}))(0.0400\text{ m})}{0.100} = 6.00\text{ W}/(\text{m}\cdot\text{K})

    Because of the reversed inequality in the previous step, you solved for an upper bound κmax⁡\kappa_{\max} rather than the required minimum threshold κmin⁡\kappa_{\min}.

WHAT YOU DID WELL
Compliments from Your Teacher

You correctly stated that internal temperature gradients must be negligible for the lumped-capacitance model to hold.

You calculated the numerical boundary value 6.00 W/(m⋅K)6.00\text{ W}/(\text{m}\cdot\text{K}) with correct units.

THE ERROR
Where Your ACEpath Teacher Spotted the Mistake
Inverted inequality condition

You copied the inequality as Bi>0.100\text{Bi} > 0.100 even though the problem explicitly specified Bi<0.100\text{Bi} < 0.100.

WHY IT HAPPENED
ACEpath Teacher's Diagnosis

You reversed the direction of the lumped-capacitance criterion. The physical meaning of the Biot number is the ratio of internal conduction resistance to external convection resistance; smaller values (Bi<0.1\text{Bi} < 0.1) ensure uniform internal temperature, which requires high thermal conductivity κ\kappa.

REASONING PATH
Your ACEpath teacher’s suggested approach
Biot Number Validity Criterion
  • Lumped capacitance is valid when Bi=internal conduction resistanceexternal convection resistance=hLcκ<0.100\text{Bi} = \frac{\text{internal conduction resistance}}{\text{external convection resistance}} = \frac{h L_c}{\kappa} < 0.100.

  • Always verify that Bi\text{Bi} is strictly less than the threshold, which requires κ>hLc0.100\kappa > \frac{h L_c}{0.100}.

CORRECTED PATH
ACEpath Teacher's Demonstration
  1. Set up the criterion: Bi=hLcκ<0.100\text{Bi} = \frac{h L_c}{\kappa} < 0.100.

  2. Rearrange for thermal conductivity: κ>hLc0.100\kappa > \frac{h L_c}{0.100}.

  3. Substitute the given numbers at the threshold boundary: κmin⁡=(15.0 W/(m2⋅K))(0.0400 m)0.100=6.00 W/(m⋅K)\kappa_{\min} = \frac{(15.0\text{ W}/(\text{m}^2\cdot\text{K}))(0.0400\text{ m})}{0.100} = 6.00\text{ W}/(\text{m}\cdot\text{K}).

Final answer

κmin⁡=6.00 W/(m⋅K)\kappa_{\min} = 6.00\text{ W}/(\text{m}\cdot\text{K})

NEXT STEPS
Final Takeaways from Your Teacher
  • Check whether physical parameters belong in the numerator or denominator when solving inequalities.

  • Remember that higher thermal conductivity κ\kappa promotes internal uniformity, so keeping internal gradients small requires a minimum conductivity, not a maximum.

OverviewACEpath Teacher's Diagnosis

03 The student incorrectly confuses the Biot number criterion for lumped capacitance with steady-state insulation and assumes external surface heat flux is zero rather than internal temperature gradients being negligible.

Sample Student Work

Reviewed by ACEpath Teacher
Step-by-Step Review
Walk Through It with Your Teacher
Partially correct
  1. Step 1

    The vessel must be perfectly insulated with zero convective heat transfer to the environment.

    Correct

    The internal temperature gradient within the vessel is negligible (∇T≈0\nabla T \approx 0), meaning the temperature T(t)T(t) is spatially uniform throughout the vessel core at every instant.

    If the vessel were perfectly insulated with zero convective heat transfer, no cooling would occur at all (dT/dt=0dT/dt = 0). Newton's Law of Cooling requires heat loss at the surface, but assumes that internal heat conduction is fast enough that temperature differences inside the object remain negligible.

  2. Step 2

    Bi=h⋅Lcκ<0.100  ⟹  κ>h⋅Lc0.100  ⟹  κmin⁡=(15.0⋅0.0400)0.100=6.00 W/(m⋅K)\text{Bi} = \frac{h \cdot L_c}{\kappa} < 0.100 \implies \kappa > \frac{h \cdot L_c}{0.100} \implies \kappa_{\min} = \frac{(15.0 \cdot 0.0400)}{0.100} = 6.00\text{ W}/(\text{m}\cdot\text{K})

WHAT YOU DID WELL
Compliments from Your Teacher

You correctly identified and applied the Biot number criterion Bi=hLcκ<0.100\text{Bi} = \frac{h L_c}{\kappa} < 0.100.

You rearranged the inequality accurately to solve for κmin⁡\kappa_{\min}.

You substituted the given values and included the correct physical units.

THE ERROR
Where Your ACEpath Teacher Spotted the Mistake
Misinterpreted Model Assumption

no

WHY IT HAPPENED
ACEpath Teacher's Diagnosis

You confused the internal spatial uniformity assumption of lumped capacitance with external thermal insulation. A lumped model relies on internal conductive resistance being much smaller than external convective resistance (Rcond≪RconvR_{\text{cond}} \ll R_{\text{conv}}), not on eliminating external heat transfer.

REASONING PATH
Your ACEpath teacher’s suggested approach
Lumped Capacitance Physical Meaning
  • Lumped-capacitance modeling represents an entire body with a single time-dependent temperature T(t)T(t), which is valid only when internal spatial temperature gradients are negligible (∇T≈0\nabla T \approx 0).

  • Whenever an ODE models temperature with respect to time alone without spatial variables, check that internal conduction is rapid relative to surface convection.

Biot Number as Ratio of Resistances
  • Bi=RcondRconv=Lc/κ1/h=hLcκ\text{Bi} = \frac{R_{\text{cond}}}{R_{\text{conv}}} = \frac{L_c / \kappa}{1 / h} = \frac{h L_c}{\kappa}. A small Biot number (Bi<0.1\text{Bi} < 0.1) requires high thermal conductivity κ\kappa, not zero surface convection hh.

  • Interpret Bi≪1\text{Bi} \ll 1 as 'nearly uniform internal temperature with external heat exchange still occurring'.

CORRECTED PATH
ACEpath Teacher's Demonstration
  1. Identify what a single state variable T(t)T(t) implies: the temperature does not depend on position (r,θ,z)(r, \theta, z).

  2. State that the internal temperature gradients are negligible ( ∇T≈0 \,\nabla T \approx 0\,), meaning the vessel interior remains spatially isothermal as it cools via external convection.

Final answer

(a) Negligible internal temperature gradients (spatially uniform temperature distribution throughout the vessel volume). (b) κmin⁡=6.00 W/(m⋅K)\kappa_{\min} = 6.00\text{ W}/(\text{m}\cdot\text{K}).

NEXT STEPS
Final Takeaways from Your Teacher
  • Review the physical interpretation of the Biot number as the ratio of internal conductive resistance to external convective resistance.

  • Practice distinguishing boundary conditions (like insulation or surface convection) from internal domain assumptions (like spatial uniformity).

Lock it in

Similar question

01

A solid metal spherical pellet of characteristic length Lc=0.0050 mL_c = 0.0050\text{ m} is cooled in air with h=25.0 W/(m2⋅K)h = 25.0\text{ W}/(\text{m}^2\cdot\text{K}). Determine the minimum thermal conductivity κmin⁡\kappa_{\min} required to keep Bi≤0.050\text{Bi} \le 0.050.

Answer

κmin⁡=2.5 W/(m⋅K)\kappa_{\min} = 2.5\text{ W}/(\text{m}\cdot\text{K}). Key step: solve Bi=hLcκ≤0.050  ⟹  κmin⁡=25.0×0.00500.050=2.5 W/(m⋅K)\text{Bi} = \frac{h L_c}{\kappa} \le 0.050 \implies \kappa_{\min} = \frac{25.0 \times 0.0050}{0.050} = 2.5\text{ W}/(\text{m}\cdot\text{K}).

02

A cylindrical ceramic sensor rod with thermal conductivity κ=1.80 W/(m⋅K)\kappa = 1.80\text{ W}/(\text{m}\cdot\text{K}) is quenched in oil. If the characteristic dimension is Lc=0.0120 mL_c = 0.0120\text{ m}, calculate the maximum allowable convective heat transfer coefficient hmax⁡h_{\max} such that the lumped-capacitance model remains valid under the criterion Bi<0.100\text{Bi} < 0.100.

Answer

hmax⁡=15.0 W/(m2⋅K)h_{\max} = 15.0\text{ W}/(\text{m}^2\cdot\text{K}). Key step: rearrange hLcκ<0.100\frac{h L_c}{\kappa} < 0.100 to get h<0.100×κLc=0.100×1.800.0120=15.0 W/(m2⋅K)h < \frac{0.100 \times \kappa}{L_c} = \frac{0.100 \times 1.80}{0.0120} = 15.0\text{ W}/(\text{m}^2\cdot\text{K}).

03

An engineer tests two hollow bioreactor shell materials in a flow chamber with h=30.0 W/(m2⋅K)h = 30.0\text{ W}/(\text{m}^2\cdot\text{K}) and effective wall thickness Lc=0.0080 mL_c = 0.0080\text{ m}. Material A has κA=1.60 W/(m⋅K)\kappa_A = 1.60\text{ W}/(\text{m}\cdot\text{K}) and Material B has κB=16.0 W/(m⋅K)\kappa_B = 16.0\text{ W}/(\text{m}\cdot\text{K}). Calculate Bi\text{Bi} for both materials and state whether each qualifies for a lumped-capacitance cooling model (extBi<0.100 ext{Bi} < 0.100).

Answer

Material A: BiA=30.0×0.00801.60=0.150\text{Bi}_A = \frac{30.0 \times 0.0080}{1.60} = 0.150 (fails criterion, lumped model invalid). Material B: BiB=30.0×0.008016.0=0.0150\text{Bi}_B = \frac{30.0 \times 0.0080}{16.0} = 0.0150 (satisfies Bi<0.100\text{Bi} < 0.100, lumped model valid).

Loading workspace…