Resources
An industrial storage silo is designed as a composite solid consisting of a right circular cylinder of radius and height capped by a hemispherical dome of the same radius . The total interior volume is fixed at . Construct the single-variable surface area function representing the exterior surface area (curved cylindrical wall plus hemispherical roof, excluding the circular base on the ground) by eliminating , express the constraint equation coupling and , and state the physical domain for .
Answer and steps
Final answer
Coupling constraint: ; Surface area function: ; Physical domain: (or ).
Steps
Formulate the Volume Constraint Equation
The silo is composed of two geometric figures sharing the same radius :
- A right circular cylinder with volume
- A hemispherical roof with volume
The total interior volume is given as . Setting up the volume equation:
Dividing both sides by :
Solve for to express the height in terms of the radius :
Construct the Exterior Surface Area Function
The exterior surface area consists of:
- The curved lateral surface of the cylinder:
- The curved surface of the hemispherical roof:
The circular base rests on the ground and is excluded from the exterior surface area. Combining these components gives:
Substitute the expression for obtained from the volume constraint:
Expand and combine like terms:
Determine the Physical Domain of
For the dimensions of the physical silo to be valid:
- The radius must be strictly positive: .
- The height of the cylindrical body must be non-negative: .
Using the relationship for :
Multiply both sides by (which is positive since ):
Combining the conditions gives the physical domain:
(Note: When , the cylinder height is , meaning the silo reduces entirely to a hemisphere of the required volume.)
Typical errors
01 The student uses the full sphere volume formula instead of the hemisphere volume when setting up the volume constraint.
Sample Student Work
Reviewed by ACEpath TeacherStep-by-Step Review
Walk Through It with Your Teacher- Step 1Correct
You used the full sphere volume for the dome. Because the dome is a hemisphere, its volume is half of a sphere: .
- Step 2Correct
Your surface area setup and algebraic expansion were completely correct, but the result inherits the incorrect coefficient from Step 1.
- Step 3Correct
Your domain logic was sound, though physical height can be zero (), and the numerical bound was altered by the earlier volume error.
WHAT YOU DID WELL
Compliments from Your TeacherYou correctly identified the relevant components for the exterior surface area, including the curved cylindrical side and hemispherical cap while excluding the floor.
You correctly solved for from your constraint equation and carried out the algebraic substitution and expansion with precision.
You established that physical dimensions impose constraints on both radius and height to identify the domain.
THE ERROR
Where Your ACEpath Teacher Spotted the Mistakeno
WHY IT HAPPENED
ACEpath Teacher's DiagnosisYou recalled the formula for the volume of a full sphere instead of halving it for a hemisphere , even though you correctly used the hemisphere formula for the surface area.
REASONING PATH
Your ACEpath teacher’s suggested approach- Hemisphere Geometric Formulas
A hemisphere is exactly one half of a complete sphere: , and its curved dome area is .
Whenever a problem specifies a dome or hemisphere, write down the full-sphere formula and explicitly multiply by before substituting it into equations.
CORRECTED PATH
ACEpath Teacher's DemonstrationSet up the total volume: .
Divide by and isolate : .
Substitute into the exterior surface area : .
Set with : .
Coupling constraint: ; Surface area function: ; Domain: (or ).
02 The student includes the circular base in the exterior surface area despite the problem specifying to exclude it.
Sample Student Work
Reviewed by ACEpath TeacherStep-by-Step Review
Walk Through It with Your Teacher- Step 1
- Step 2Correct
You added the circular base area to the exterior surface area, but the problem specifies that the circular base on the ground is excluded.
- Step 3Correct
Your algebraic substitution and expansion were executed correctly, but this step carries forward the extra term from Step 2.
- Step 4
WHAT YOU DID WELL
Compliments from Your TeacherYou correctly formulated the composite volume equation and isolated the height .
You properly substituted your height expression into your surface area model and simplified the algebraic terms.
You correctly analyzed the non-negativity constraint on to identify the upper bound of the domain.
THE ERROR
Where Your ACEpath Teacher Spotted the MistakeYou included the circular base in the surface area summation.
WHY IT HAPPENED
ACEpath Teacher's DiagnosisYou likely used the complete closed surface area formula for a composite solid out of habit rather than adhering strictly to the boundary conditions specified in the problem statement (excluding the base on the ground).
REASONING PATH
Your ACEpath teacher’s suggested approach- Inventory Boundary Faces
For open or partially grounded composite solids, list each face explicitly before adding.
Check off each surface component against the problem statement (e.g., dome = , wall = , base = excluded) before writing the total area expression.
- Include Degenerate Extremes in Physical Domains
Geometric lengths and heights can often reach zero unless an open interior boundary is explicitly specified.
Allow , which includes the solid hemisphere boundary case where .
CORRECTED PATH
ACEpath Teacher's DemonstrationSet up the exterior surface area without the circular ground base: .
Substitute into the corrected area formula: .
Distribute and collect like terms: .
Coupling constraint: ; Surface area function: ; Physical domain: (or m).
03 The student ignores the constraint that the cylinder height h must be greater than zero, stating the domain only as r > 0.
Sample Student Work
Reviewed by ACEpath TeacherStep-by-Step Review
Walk Through It with Your Teacher- Step 1
- Step 2
- Step 3
Since represents a physical radius,
CorrectYou only required the radius to be positive, but the cylinder height must also be non-negative (). Setting yields the upper bound .
WHAT YOU DID WELL
Compliments from Your TeacherYou correctly combined the volume formulas of the cylinder and hemisphere to express the height in terms of .
You accurately substituted the height expression into the exterior surface area formula and simplified the algebraic terms.
THE ERROR
Where Your ACEpath Teacher Spotted the MistakeYou recognized that geometric lengths must be strictly positive (), but you did not check whether your expression for remains physically possible over all positive values of .
WHY IT HAPPENED
ACEpath Teacher's DiagnosisIn geometric optimization and modeling problems, eliminating a variable requires imposing physical feasibility conditions on all original geometric dimensions, not just the chosen independent variable. Setting provides the upper bound on .
REASONING PATH
Your ACEpath teacher’s suggested approach- Check all eliminated variables for geometric feasibility
Every physical dimension () must satisfy non-negativity ( and ).
Substitute your eliminated variable expression into the inequality and solve for the independent variable to determine the upper bound.
CORRECTED PATH
ACEpath Teacher's DemonstrationSet : .
Multiply both sides by (valid since ): .
Rearrange to solve for : .
Take the cube root: .
Coupling constraint: ; Surface area function: ; Physical domain: (or ).
Lock it in
What are the volume and curved surface area formulas for a hemisphere of radius ?
and . Each is exactly half of the corresponding full-sphere formula (, ).
Similar question
A cylindrical tank with a hemispherical top has a fixed volume of . Express the height of the cylindrical part as a function of the radius .
Answer
Set the volume sum to : . Dividing by gives .
A storage capsule is formed by joining two identical hemispherical caps to both ends of a cylinder of radius and length . If the total volume is , express the total surface area purely in terms of .
Answer
Two hemispherical caps form one complete sphere of volume and surface area . Constraint: . Surface area: .
An open grain silo consists of a cylindrical lower section of height and radius , open at the top and fitted with an inverted conical hopper at the bottom of the same radius and height . If the total volume is , express the total exterior wall surface area (curved cylinder plus curved cone) in terms of and , and determine the maximum possible radius.
Answer
Cone volume is . Cylinder volume is . Volume constraint: . The cone's slant height is , so its lateral area is . The cylinder lateral area is . Thus, . Since , .