Resources
In a chemistry analytical lab, a student titrates a aliquot of an unknown monoprotic weak acid with standardized . A digital pH meter records the following discrete pairs during the titration: , , , and . By recognizing the half-equivalence point from this data table, determine the acid dissociation constant of the weak acid, choose the appropriate logarithmic function representation relating to titrant volume across the buffer region , and calculate the original analytical concentration of the acid.
Answer and steps
Final answer
Original acid concentration: ; Half-equivalence volume: , giving and ; Buffer region model: .
Steps
Identify the Equivalence Point and Calculate
In the titration of a monoprotic weak acid with a strong base (), the equivalence point occurs where the acid is fully neutralized to its conjugate base, resulting in a basic (greater than ). From the experimental data table, the rapid jump to at marks the equivalence point volume:
At equivalence, the moles of added base equal the initial moles of weak acid:
Substitute the known quantities (, , and ):
Determine and from the Half-Equivalence Point
The half-equivalence point occurs at exactly half the equivalence volume:
At this volume, exactly half of the initial weak acid has been converted into its conjugate base , so . Applying the Henderson-Hasselbalch equation:
From the table, at , the measured is . Therefore:
Calculate the acid dissociation constant :
Model the Buffer Region Function
Throughout the buffer region (), the titration reaction is:
For any volume of titrant added:
- The amount of conjugate base formed is proportional to the titrant added: .
- The remaining amount of weak acid is: .
Because both species are dissolved in the same total solution volume, their concentration ratio equals their molar ratio:
Substituting this ratio and into the Henderson-Hasselbalch equation gives the model:
(Check: At , , which closely matches the experimental data.)
Typical errors
01 The student misidentifies the half-equivalence point as the first measured point at V = 10.00 mL instead of half of the equivalence volume V = 12.50 mL.
Sample Student Work
Reviewed by ACEpath TeacherStep-by-Step Review
Walk Through It with Your Teacher- Step 1Correct
You correctly identified , but the half-equivalence point occurs at exactly half of the equivalence volume, , not . From the data table, the at is , so and .
- Step 2Correct
You formulated the buffer function using the correct Henderson-Hasselbalch ratio , but this step is affected because you inserted the earlier incorrect value instead of .
- Step 3
WHAT YOU DID WELL
Compliments from Your TeacherYou correctly identified the equivalence point volume as .
You accurately calculated the initial acid concentration as using the equivalence condition.
You recognized the correct functional structure of the Henderson-Hasselbalch equation across the buffer region.
THE ERROR
Where Your ACEpath Teacher Spotted the Mistakeno
WHY IT HAPPENED
ACEpath Teacher's DiagnosisYou selected an arbitrary intermediate volume from the table () instead of computing half of the equivalence volume ().
REASONING PATH
Your ACEpath teacher’s suggested approach- Half-Equivalence Point Condition
For a monoprotic weak acid titrated with a strong base, the half-equivalence point is always located at . At this volume, and .
Divide the equivalence volume by () and read the corresponding from the data table.
CORRECTED PATH
ACEpath Teacher's DemonstrationCompute the exact half-equivalence volume: .
Look up the measured at from the table to find .
Calculate the dissociation constant: .
Substitute into your buffer model: .
, , and
02 The student inverts the ratio of conjugate base to weak acid in the Henderson-Hasselbalch logarithmic term.
Sample Student Work
Reviewed by ACEpath TeacherStep-by-Step Review
Walk Through It with Your Teacher- Step 1
- Step 2Correct
You placed the unreacted weak acid in the numerator and the conjugate base in the denominator. The Henderson-Hasselbalch logarithmic argument is , which equals .
- Step 3
WHAT YOU DID WELL
Compliments from Your TeacherYou correctly identified the equivalence volume () and half-equivalence volume () from the data table.
You correctly found and calculated .
You correctly calculated the analytical concentration .
THE ERROR
Where Your ACEpath Teacher Spotted the MistakeYou placed in the numerator and in the denominator inside the logarithm.
WHY IT HAPPENED
ACEpath Teacher's DiagnosisYou inverted the standard Henderson-Hasselbalch ratio , which causes the calculated to decrease rather than increase as titrant is added.
REASONING PATH
Your ACEpath teacher’s suggested approach- Henderson-Hasselbalch Quotient
Always verify that the conjugate base concentration is in the numerator and the weak acid concentration is in the denominator.
- Monotonicity Sanity Check
Adding strong base must increase the of the solution over the interval .
Check your model at : , which matches the experimental data.
CORRECTED PATH
ACEpath Teacher's DemonstrationState the Henderson-Hasselbalch equation: .
Express the molar amounts of each species in terms of titrant volume : and .
Form the ratio .
Substitute the ratio and into the equation to produce .
03 The student mistakes the half-equivalence volume V = 12.50 mL for the equivalence point volume when calculating the original concentration Ca.
Sample Student Work
Reviewed by ACEpath TeacherStep-by-Step Review
Walk Through It with Your Teacher- Step 1
- Step 2
- Step 3Correct
You substituted the half-equivalence volume into the stoichiometry equation instead of the full equivalence volume . Stoichiometric neutralization occurs when moles of base equal total initial moles of acid at the equivalence point.
WHAT YOU DID WELL
Compliments from Your TeacherYou correctly identified both the equivalence volume and the half-equivalence volume from the titration data.
You correctly applied the relation at half-equivalence to calculate .
You correctly formulated the logarithmic model relating to added volume in the buffer region.
THE ERROR
Where Your ACEpath Teacher Spotted the MistakeYou accidentally selected instead of in your stoichiometric calculation.
WHY IT HAPPENED
ACEpath Teacher's DiagnosisYou conflated the thermodynamic condition of the half-equivalence point (, used for finding ) with the stoichiometric condition of complete neutralization (, which occurs at the full equivalence point ).
REASONING PATH
Your ACEpath teacher’s suggested approach- Stoichiometric Neutralization
Complete neutralization of monoprotic acid requires , where is the full equivalence volume.
Always verify that you use the volume where the sharpest pH change occurs (), not the buffer midpoint (), when solving for initial analytical concentration.
CORRECTED PATH
ACEpath Teacher's DemonstrationSet up the stoichiometric mole balance at the full equivalence point: , so .
Substitute the full equivalence volume along with and : .
Solve for : .
Lock it in
What is the defining formula for the titrant volume at the half-equivalence point in a weak acid titration?
. Exactly half of the weak acid has been converted to conjugate base, making and .
Similar question
A sample of an unknown weak acid is titrated with . The equivalence point occurs at . A digital sensor records at . Determine the acid dissociation constant and the original analytical concentration of the acid.
Answer
and . Molar equivalence: . Half-equivalence volume is , where .
A solution of a weak monoprotic acid is titrated with , reaching equivalence at . At , the measured is . Write the function across the buffer region , and calculate the theoretical at .
Answer
; at , . With from , evaluating at yields .
A aliquot of a diprotic weak acid is titrated with . The titration displays two equivalence points at and . Identify the specific titrant volumes at which and .
Answer
at ; at . The first half-equivalence point is at . The second buffer midpoint occurs halfway between the two equivalence points: .