Resources

A structural engineering firm uses a coordinate frame where downward forces are treated as negative (ΣFy=0\Sigma F_y = 0) and counterclockwise moments are treated as positive (ΣM=0\Sigma M = 0). A horizontal beam of span L=6.0 mL = 6.0\text{ m} is supported by pin supports at its left end AA (x=0x = 0) and right end BB (x=6.0 mx = 6.0\text{ m}). Two concentrated downward loads act on the beam: P1=40 kNP_1 = 40\text{ kN} located at x=1.5 mx = 1.5\text{ m} and P2=60 kNP_2 = 60\text{ kN} located at x=4.5 mx = 4.5\text{ m}. Using the strict sign convention that upward reaction forces RAR_A and RBR_B are positive, write the two-variable system of static equilibrium equations (force balance and moment balance about pin AA), and solve for the vertical reaction forces RAR_A and RBR_B in kN\text{kN}.

Answer and steps

Final answer

Under the designated sign convention, the system of equilibrium equations is: {RA+RB−40−60=0−40(1.5)−60(4.5)+RB(6.0)=0\begin{cases} R_A + R_B - 40 - 60 = 0 \\ -40(1.5) - 60(4.5) + R_B(6.0) = 0 \end{cases}, or {RA+RB=1006.0RB=330\begin{cases} R_A + R_B = 100 \\ 6.0R_B = 330 \end{cases}. Solving gives RB=55.0 kNR_B = 55.0\text{ kN} and RA=45.0 kNR_A = 45.0\text{ kN}.

Steps

01

Set Up the Vertical Force Equilibrium Equation

Static equilibrium requires the sum of all vertical forces to be zero: ΣFy=0\Sigma F_y = 0

According to the given sign convention, upward reaction forces are positive (+RA+R_A, +RB+R_B) and downward applied loads are negative (−40 kN-40\text{ kN}, −60 kN-60\text{ kN}): RA+RB−40−60=0R_A + R_B - 40 - 60 = 0

Simplifying this yields our first linear equation: RA+RB=100R_A + R_B = 100


02

Set Up the Moment Equilibrium Equation about Pin AA

Rotational equilibrium requires the sum of moments about any point to equal zero: ΣMA=0\Sigma M_A = 0

A moment is defined as the force multiplied by its perpendicular distance from the pivot point:

  • The line of action of RAR_A passes directly through pin AA (x=0x = 0), producing zero moment: RA⋅0=0R_A \cdot 0 = 0.
  • The downward load of 40 kN40\text{ kN} at x=1.5 mx = 1.5\text{ m} creates a clockwise (negative) moment: −40⋅1.5=−60 kN⋅m-40 \cdot 1.5 = -60\text{ kN}\cdot\text{m}.
  • The downward load of 60 kN60\text{ kN} at x=4.5 mx = 4.5\text{ m} creates a clockwise (negative) moment: −60⋅4.5=−270 kN⋅m-60 \cdot 4.5 = -270\text{ kN}\cdot\text{m}.
  • The upward support reaction RBR_B at x=6.0 mx = 6.0\text{ m} creates a counterclockwise (positive) moment: +RB⋅6.0=6.0RB+R_B \cdot 6.0 = 6.0 R_B.

Summing the moments gives: −40(1.5)−60(4.5)+RB(6.0)=0-40(1.5) - 60(4.5) + R_B(6.0) = 0

Combining the constant terms: −330+6.0RB=0  ⟹  6.0RB=330-330 + 6.0 R_B = 0 \implies 6.0 R_B = 330


03

State the System of Equations and Solve

The resulting two-variable system of linear equations is: {RA+RB=100,6.0RB=330\lbrace R_A + R_B = 100,\quad 6.0 R_B = 330

Solve the second equation directly for RBR_B: RB=3306.0=55.0 kNR_B = \frac{330}{6.0} = 55.0\text{ kN}

Substitute RB=55.0 kNR_B = 55.0\text{ kN} back into the force balance equation: RA+55.0=100R_A + 55.0 = 100 RA=100−55.0=45.0 kNR_A = 100 - 55.0 = 45.0\text{ kN}

Common Pitfall: A frequent mistake is forgetting to assign negative signs to downward loads when calculating moments about the left end, which would incorrectly predict a downward reaction at support BB. Always trace the rotation direction (clockwise vs. counterclockwise) relative to the pivot.

Educational illustration for this question

Typical errors

OverviewACEpath Teacher's Diagnosis

01 The student misapplies the sign convention by treating downward applied loads as counterclockwise moments instead of clockwise, adding them to RB's counterclockwise moment.

Sample Student Work

Reviewed by ACEpath Teacher
Step-by-Step Review
Walk Through It with Your Teacher
Incorrect
  1. Step 1

    RA+RB−40−60=0  ⟹  RA+RB=100R_A + R_B - 40 - 60 = 0 \implies R_A + R_B = 100

  2. Step 2

    6.0RB+40(1.5)+60(4.5)=0  ⟹  6.0RB+330=06.0R_B + 40(1.5) + 60(4.5) = 0 \implies 6.0R_B + 330 = 0

    Correct

    RB(6.0)−40(1.5)−60(4.5)=0  ⟹  6.0RB−330=0R_B(6.0) - 40(1.5) - 60(4.5) = 0 \implies 6.0R_B - 330 = 0

    About pin AA at x=0x = 0, the downward loads tend to rotate the beam clockwise. Under the standard convention where counterclockwise moments are positive, clockwise moments must carry a negative sign, giving −40(1.5)−60(4.5)-40(1.5) - 60(4.5).

  3. Step 3

    6.0RB=−330  ⟹  RB=−55 kN6.0R_B = -330 \implies R_B = -55\text{ kN}

    Correct

    6.0RB=330  ⟹  RB=55.0 kN6.0R_B = 330 \implies R_B = 55.0\text{ kN}

    Your algebra in isolating RBR_B was carried out correctly, but the resulting negative value was caused by the sign error in the moment equation.

  4. Step 4

    RA=100−(−55)=155 kNR_A = 100 - (-55) = 155\text{ kN}

    Correct

    RA=100−55.0=45.0 kNR_A = 100 - 55.0 = 45.0\text{ kN}

    Your substitution into the force equation was mathematically consistent, but the value is incorrect due to the propagated sign error from RBR_B.

WHAT YOU DID WELL
Compliments from Your Teacher

You correctly formulated the vertical force balance equation ΣFy=0\Sigma F_y = 0.

You correctly identified the moment arms (1.5 m1.5\text{ m}, 4.5 m4.5\text{ m}, and 6.0 m6.0\text{ m}) relative to pivot AA.

You executed the algebraic substitution to solve the linear system accurately based on your equations.

THE ERROR
Where Your ACEpath Teacher Spotted the Mistake
Moment Sign Convention Error

You added the downward load moments to the upward support moment as positive values rather than subtracting them for their clockwise rotation.

WHY IT HAPPENED
ACEpath Teacher's Diagnosis

Confusing the rotational tendency of a force about a pivot point with its directional sign in linear force balance, forgetting that downward forces located to the right of the pivot create clockwise (negative) moments.

REASONING PATH
Your ACEpath teacher’s suggested approach
Check Rotational Sense
  • A moment is positive if it rotates counterclockwise about the chosen pivot, and negative if it rotates clockwise: M=±(F×d)M = \pm (F \times d).

  • Place your pencil tip on the pivot point and push in the direction of the force vector to see whether the beam rotates clockwise or counterclockwise.

Sanity Check Support Reactions
  • For purely downward loads within the span of a simply supported beam, both upward reaction forces must be positive and strictly less than the total applied load.

  • Verify that 0<RA<100 kN0 < R_A < 100\text{ kN} and 0<RB<100 kN0 < R_B < 100\text{ kN}.

CORRECTED PATH
ACEpath Teacher's Demonstration
  1. Set up the moment equilibrium about pin AA with correct rotation signs: RB(6.0)−40(1.5)−60(4.5)=0R_B(6.0) - 40(1.5) - 60(4.5) = 0.

  2. Simplify the moment equation: 6.0RB−60−270=0  ⟹  6.0RB=3306.0R_B - 60 - 270 = 0 \implies 6.0R_B = 330.

  3. Solve for the right reaction: RB=3306.0=55.0 kNR_B = \frac{330}{6.0} = 55.0\text{ kN}.

  4. Substitute RB=55.0 kNR_B = 55.0\text{ kN} into RA+RB=100R_A + R_B = 100: RA=100−55.0=45.0 kNR_A = 100 - 55.0 = 45.0\text{ kN}.

Final answer

RA=45.0 kNR_A = 45.0\text{ kN} and RB=55.0 kNR_B = 55.0\text{ kN}

NEXT STEPS
Final Takeaways from Your Teacher
  • Practice drawing curved directional arrows next to each force to explicitly indicate clockwise (−-) or counterclockwise (++) rotation.

  • Solve the beam reaction practice problems below to master rotational equilibrium conventions.

OverviewACEpath Teacher's Diagnosis

02 The student incorrectly calculates the moment arm of P2 from support B instead of from reference pin A, using 1.5 m instead of 4.5 m.

Sample Student Work

Reviewed by ACEpath Teacher
Step-by-Step Review
Walk Through It with Your Teacher
Partially correct
  1. Step 1

    R_A + R_B - 40 - 60 = 0   ⟹  \implies R_A + R_B = 100

  2. Step 2

    6.0R_B - 40(1.5) - 60(1.5) = 0   ⟹  \implies 6.0R_B - 150 = 0   ⟹  \implies 6.0R_B = 150

    Correct

    -40(1.5) - 60(4.5) + R_B(6.0) = 0   ⟹  \implies 6.0R_B = 330

    When summing moments about pin AA at x=0x = 0, the moment arm for each force must be measured from AA. The load P2=60 kNP_2 = 60\text{ kN} is located at x=4.5 mx = 4.5\text{ m}, so its moment arm is 4.5 m4.5\text{ m}, not 1.5 m1.5\text{ m} (which is its distance from support BB).

  3. Step 3

    R_B = 25 kN\text{ kN}   ⟹  \implies R_A = 100 - 25 = 75 kN\text{ kN}

    Correct

    R_B = 3306.0\frac{330}{6.0} = 55.0 kN\text{ kN}   ⟹  \implies R_A = 100 - 55.0 = 45.0 kN\text{ kN}

    Your algebraic solving technique was correct, but your reaction values were affected by the incorrect moment equation in Step 2.

WHAT YOU DID WELL
Compliments from Your Teacher

You correctly established the equilibrium condition for vertical forces ΣFy=0\Sigma F_y = 0.

You accurately assigned positive signs to upward reactions and negative signs to downward loads.

You used consistent algebraic substitution to solve for the second reaction force once the first was obtained.

THE ERROR
Where Your ACEpath Teacher Spotted the Mistake
Incorrect moment arm reference point

You used the distance of P2P_2 from the right support BB (6.0−4.5=1.5 m6.0 - 4.5 = 1.5\text{ m}) rather than its distance from the pivot pin AA (4.5 m4.5\text{ m}).

WHY IT HAPPENED
ACEpath Teacher's Diagnosis

Confusing the distance to the nearest support or span segment with the perpendicular distance measured specifically from the chosen moment pivot point.

REASONING PATH
Your ACEpath teacher’s suggested approach
Reference Pivot Check
  • Every moment term M=F⋅dM = F \cdot d must measure dd strictly from the designated pivot point.

  • Before multiplying, circle the pivot point on a beam sketch and draw an explicit dimension line from that pivot to each load's line of action.

Physical Reasonableness Check
  • A load located closer to support BB must induce a larger reaction at BB than at AA.

  • Since the 60 kN60\text{ kN} load is at x=4.5 mx = 4.5\text{ m} (closer to BB), check that RB>RAR_B > R_A in your final values.

CORRECTED PATH
ACEpath Teacher's Demonstration
  1. Write the moment balance about pin AA using the true distance x=4.5 mx = 4.5\text{ m} for P2P_2: 6.0RB−40(1.5)−60(4.5)=06.0R_B - 40(1.5) - 60(4.5) = 0

  2. Evaluate the constant terms: 6.0RB−60−270=0  ⟹  6.0RB=3306.0R_B - 60 - 270 = 0 \implies 6.0R_B = 330

  3. Solve for RBR_B: RB=3306.0=55.0 kNR_B = \frac{330}{6.0} = 55.0\text{ kN}

  4. Substitute RB=55.0 kNR_B = 55.0\text{ kN} into RA+RB=100R_A + R_B = 100: RA=100−55.0=45.0 kNR_A = 100 - 55.0 = 45.0\text{ kN}

Final answer

R_A = 45.0 kN\text{ kN},  R_B = 55.0 kN\text{ kN}

NEXT STEPS
Final Takeaways from Your Teacher
  • Draw an annotated free-body diagram showing explicit dimension lines starting from the chosen pivot point AA.

  • Practice calculating moments about both pin AA and pin BB to verify that both choices yield identical reaction forces.

OverviewACEpath Teacher's Diagnosis

03 The student confuses the positions of the reaction forces, mistakenly placing the moment arm of RA at 6.0 m and solving for RA instead of RB in the moment equation about A.

Sample Student Work

Reviewed by ACEpath Teacher
Step-by-Step Review
Walk Through It with Your Teacher
Partially correct
  1. Step 1

    R_A + R_B - 40 - 60 = 0   ⟹  \implies R_A + R_B = 100

  2. Step 2

    6.0 R_A - 40(1.5) - 60(4.5) = 0   ⟹  \implies 6.0 R_A - 330 = 0   ⟹  \implies 6.0 R_A = 330

    Correct

    R_A(0) - 40(1.5) - 60(4.5) + 6.0 R_B = 0   ⟹  \implies 6.0 R_B = 330

    When taking moments about pin AA (x=0x = 0), the line of action of RAR_A passes through AA, giving it a moment arm of 0 m0\text{ m}. The support at x=6.0 mx = 6.0\text{ m} is pin BB, so the 6.0 m6.0\text{ m} moment arm belongs to RBR_B, not RAR_A.

  3. Step 3

    R_A = 55 kN\text{ kN}

    Correct

    R_B = 3306.0\frac{330}{6.0} = 55.0 kN\text{ kN}

    Your algebraic division was carried out correctly, but solving the mislabeled moment equation produced the value for RAR_A instead of RBR_B.

  4. Step 4

    R_B = 100 - 55 = 45 kN\text{ kN}

    Correct

    R_A = 100 - 55.0 = 45.0 kN\text{ kN}

    You substituted correctly into your vertical equilibrium equation, but due to the swapped variable from the previous step, this yielded 45 kN45\text{ kN} for RBR_B rather than RAR_A.

WHAT YOU DID WELL
Compliments from Your Teacher

You correctly set up and simplified the vertical force equilibrium equation ΣFy=0\Sigma F_y = 0.

You correctly calculated the moment magnitudes and clockwise signs for both downward loads.

You solved the resulting linear system accurately using substitution.

THE ERROR
Where Your ACEpath Teacher Spotted the Mistake
Moment arm pivot mismatch

You accidentally assigned the span distance of 6.0 m6.0\text{ m} to the support reaction at the pivot point AA rather than the opposite support at BB.

WHY IT HAPPENED
ACEpath Teacher's Diagnosis

Confusing the pivot location with the opposite boundary support when assigning moment arms (lever arms) in rotational equilibrium equations.

REASONING PATH
Your ACEpath teacher’s suggested approach
Check the pivot point distance
  • The moment arm of any force whose line of action passes through the reference pivot point is identically zero.

  • Always verify that the force acting at the chosen pivot point is multiplied by 00, while forces located away from the pivot are multiplied by their respective nonzero distances.

CORRECTED PATH
ACEpath Teacher's Demonstration
  1. Set up the moment equilibrium equation about pivot AA: ΣMA=−40(1.5)−60(4.5)+6.0RB=0\Sigma M_A = -40(1.5) - 60(4.5) + 6.0 R_B = 0.

  2. Simplify the moment equation: 6.0RB=330  ⟹  RB=55.0 kN6.0 R_B = 330 \implies R_B = 55.0\text{ kN}.

  3. Substitute RB=55.0 kNR_B = 55.0\text{ kN} into the vertical force equation: RA+55.0=100  ⟹  RA=45.0 kNR_A + 55.0 = 100 \implies R_A = 45.0\text{ kN}.

Final answer

RA=45.0 kNR_A = 45.0\text{ kN}, RB=55.0 kNR_B = 55.0\text{ kN}

NEXT STEPS
Final Takeaways from Your Teacher
  • Before writing each moment term, label each force with its coordinates to clearly match each lever arm to the correct reaction force.

  • Practice computing equilibrium reactions by taking moments about support BB as an independent self-check.

Lock it in

Similar question

01

A horizontal beam of length 4.0 m4.0\text{ m} is supported at end AA (x=0x = 0) and end BB (x=4.0 mx = 4.0\text{ m}). A single downward load of 50 kN50\text{ kN} acts at x=1.0 mx = 1.0\text{ m}. Using counterclockwise moments as positive and upward forces as positive, write the moment equation about AA and solve for RAR_A and RBR_B.

Answer

Moment balance about AA: RB(4.0)−50(1.0)=0  ⟹  RB=12.5 kNR_B(4.0) - 50(1.0) = 0 \implies R_B = 12.5\text{ kN}. Force balance: RA+RB=50  ⟹  RA=50−12.5=37.5 kNR_A + R_B = 50 \implies R_A = 50 - 12.5 = 37.5\text{ kN}.

02

A beam of length 8.0 m8.0\text{ m} rests on supports at AA (x=0x = 0) and BB (x=8.0 mx = 8.0\text{ m}). It carries two downward loads: 30 kN30\text{ kN} at x=2.0 mx = 2.0\text{ m} and 70 kN70\text{ kN} at x=6.0 mx = 6.0\text{ m}. Write the system of two equilibrium equations and solve for vertical reaction forces RAR_A and RBR_B.

Answer

System: {RA+RB=100,8.0RB−30(2.0)−70(6.0)=0\lbrace R_A + R_B = 100,\quad 8.0R_B - 30(2.0) - 70(6.0) = 0. From moment balance: 8.0RB=60+420=480  ⟹  RB=60 kN8.0R_B = 60 + 420 = 480 \implies R_B = 60\text{ kN}. Then RA=100−60=40 kNR_A = 100 - 60 = 40\text{ kN}.

03

A beam of length 10.0 m10.0\text{ m} has support AA at x=2.0 mx = 2.0\text{ m} and support BB at x=10.0 mx = 10.0\text{ m}. A downward load of 20 kN20\text{ kN} acts at the overhang tip x=0x = 0, and another downward load of 80 kN80\text{ kN} acts at x=6.0 mx = 6.0\text{ m}. Taking moments about pin AA with counterclockwise positive, find RAR_A and RBR_B.

Answer

Moment balance about AA (x=2.0 mx = 2.0\text{ m}): The overhang load at x=0x = 0 is 2.0 m2.0\text{ m} to the left, causing counterclockwise rotation: +20(2.0)=+40 kN⋅m+20(2.0) = +40\text{ kN}\cdot\text{m}. The load at x=6.0 mx = 6.0\text{ m} is 4.0 m4.0\text{ m} to the right, causing clockwise rotation: −80(4.0)=−320 kN⋅m-80(4.0) = -320\text{ kN}\cdot\text{m}. Support BB is 8.0 m8.0\text{ m} to the right, causing counterclockwise rotation: +RB(8.0)+R_B(8.0). Equation: RB(8.0)+40−320=0  ⟹  8.0RB=280  ⟹  RB=35.0 kNR_B(8.0) + 40 - 320 = 0 \implies 8.0R_B = 280 \implies R_B = 35.0\text{ kN}. Vertical balance: RA+RB=100  ⟹  RA=65.0 kNR_A + R_B = 100 \implies R_A = 65.0\text{ kN}.

Loading workspace…