Resources

A laboratory chromatography column elutes a chemical sample where the concentration CC is recorded in non-standard laboratory units of milligrams per deciliter (mg/dL\text{mg/dL}), while the delivery pump flow rate vv is measured in milliliters per minute (mL/min\text{mL/min}). The observed relationship follows the empirical formula C(v)=250−0.8vC(v) = 250 - 0.8v. Convert the dependent variable CC into standard SI molar concentration units of millimoles per liter (mmol/L\text{mmol/L}) for a solute with a molar mass of 180.16 g/mol180.16\text{ g/mol}, and write the converted function representation CSI(v)C_{\text{SI}}(v) expressing concentration in mmol/L\text{mmol/L} as a function of pump velocity vv in mL/min\text{mL/min}.

Answer and steps

Final answer

CSI(v)=10180.16(250−0.8v)≈13.88−0.0444v mmol/LC_{\text{SI}}(v) = \frac{10}{180.16}(250 - 0.8v) \approx 13.88 - 0.0444v\text{ mmol/L} (exact: CSI(v)=125009008−2450.4v=31252252−1225.2v mmol/LC_{\text{SI}}(v) = \frac{12500}{9008} - \frac{2}{450.4}v = \frac{3125}{2252} - \frac{1}{225.2}v\text{ mmol/L}).

Steps

01

Determine the conversion factor from mg/dL\text{mg/dL} to mmol/L\text{mmol/L}

To convert a concentration from milligrams per deciliter (mg/dL\text{mg/dL}) to millimoles per liter (mmol/L\text{mmol/L}), convert the volume unit (denominator) and the mass unit (numerator) systematically:

  1. Volume conversion (dL\text{dL} to L\text{L}): 1 dL=0.1 L=10−1 L1\text{ dL} = 0.1\text{ L} = 10^{-1}\text{ L} Therefore: 1 mg1 dL=1 mg0.1 L=10 mg/L\frac{1\text{ mg}}{1\text{ dL}} = \frac{1\text{ mg}}{0.1\text{ L}} = 10\text{ mg/L}
  2. Mass-to-mole conversion (mg\text{mg} to mmol\text{mmol}): The molar mass is M=180.16 g/molM = 180.16\text{ g/mol}, which is equivalent to 180.16 mg/mmol180.16\text{ mg/mmol}: 1 mg=1180.16 mmol1\text{ mg} = \frac{1}{180.16}\text{ mmol}
  3. Combined conversion factor: Combining both relations gives: 1 mg/dL=10180.16 mmol/L1\text{ mg/dL} = \frac{10}{180.16}\text{ mmol/L}
02

Apply the conversion factor to the original function

The given empirical model is: C(v)=250−0.8v(mg/dL)C(v) = 250 - 0.8v\quad (\text{mg/dL})

Multiplying the entire expression by the conversion factor gives the function CSI(v)C_{\text{SI}}(v) in mmol/L\text{mmol/L}: CSI(v)=10180.16(250−0.8v)C_{\text{SI}}(v) = \frac{10}{180.16}\left(250 - 0.8v\right)

03

Expand and simplify the coefficients

Distribute the factor to write the equation in linear slope-intercept form:

  • Constant term: 10⋅250180.16=2500180.16≈13.88 mmol/L\frac{10 \cdot 250}{180.16} = \frac{2500}{180.16} \approx 13.88\text{ mmol/L}
  • Slope term: 10⋅(−0.8)180.16=−8180.16≈−0.0444 (mmol⋅min)/(L⋅mL)\frac{10 \cdot (-0.8)}{180.16} = -\frac{8}{180.16} \approx -0.0444\text{ (mmol}\cdot\text{min)/(L}\cdot\text{mL)}

Thus, the converted function representation is: CSI(v)=10180.16(250−0.8v)≈13.88−0.0444v mmol/LC_{\text{SI}}(v) = \frac{10}{180.16}(250 - 0.8v) \approx 13.88 - 0.0444v\text{ mmol/L}

(Pitfall to avoid: Do not apply the unit conversion only to the constant 250250. Because the unit of C(v)C(v) belongs to the entire output value, the scaling factor must multiply both terms, or the units of the rate coefficient would be inconsistent with the output.)

Typical errors

OverviewACEpath Teacher's Diagnosis

01 The student confuses the metric prefix deciliter (1 dL = 0.1 L) with milliliter or multiplies by 0.1 instead of 10, incorrectly dividing by 10 when converting from per deciliter to per liter.

Sample Student Work

Reviewed by ACEpath Teacher
Step-by-Step Review
Walk Through It with Your Teacher
Incorrect
  1. Step 1

    1 mg/dL=0.1 mg/L1\text{ mg/dL} = 0.1\text{ mg/L}

    Correct

    1 mg/dL=1 mg0.1 L=10 mg/L1\text{ mg/dL} = \frac{1\text{ mg}}{0.1\text{ L}} = 10\text{ mg/L}

    Because 1 dL=0.1 L1\text{ dL} = 0.1\text{ L} appears in the denominator, converting from per deciliter to per liter requires dividing by 0.10.1 (or multiplying by 1010). There are 10 dL10\text{ dL} in a full liter, so a solution of 1 mg/dL1\text{ mg/dL} contains 10 mg10\text{ mg} in every liter.

  2. Step 2

    Molar mass=180.16 mg/mmol  ⟹  Conversion factor=0.1180.16=0.000555 mmol/L per mg/dL\text{Molar mass} = 180.16\text{ mg/mmol} \implies \text{Conversion factor} = \frac{0.1}{180.16} = 0.000555\text{ mmol/L per mg/dL}

    Correct

    Conversion factor=10180.16 (mmol/L)/(mg/dL)≈0.05551 (mmol/L)/(mg/dL)\text{Conversion factor} = \frac{10}{180.16}\text{ (mmol/L)/(mg/dL)} \approx 0.05551\text{ (mmol/L)/(mg/dL)}

    You recognized that 1 g/mol=1 mg/mmol1\text{ g/mol} = 1\text{ mg/mmol} and correctly placed the molar mass in the denominator. However, carrying forward the 0.10.1 factor from Step 1 caused the overall conversion factor to be 100100 times too small.

  3. Step 3

    CSI(v)=(0.1180.16)∗(250−0.8v)=0.1388−0.000444vC_{\text{SI}}(v) = \left(\frac{0.1}{180.16}\right) * (250 - 0.8v) = 0.1388 - 0.000444v

    Correct

    CSI(v)=(10180.16)(250−0.8v)≈13.88−0.0444vC_{\text{SI}}(v) = \left(\frac{10}{180.16}\right)(250 - 0.8v) \approx 13.88 - 0.0444v

    You correctly distributed the conversion factor across both terms of the linear model, but the resulting coefficients reflect the earlier denominator conversion error.

WHAT YOU DID WELL
Compliments from Your Teacher

You correctly identified that a molar mass of 180.16 g/mol180.16\text{ g/mol} equals 180.16 mg/mmol180.16\text{ mg/mmol}.

You placed the molar mass in the denominator to convert milligrams to millimoles.

You correctly distributed the conversion factor to both the constant and slope terms of the linear function.

THE ERROR
Where Your ACEpath Teacher Spotted the Mistake
Denominator metric unit conversion error

no

WHY IT HAPPENED
ACEpath Teacher's Diagnosis

You treated the metric prefix conversion for a unit in the denominator as a direct multiplication by 0.10.1 rather than dividing by the volume equivalence (1 dL=0.1 L1\text{ dL} = 0.1\text{ L}), reversing the scale factor between deciliters and liters.

REASONING PATH
Your ACEpath teacher’s suggested approach
Converting denominator units
  • When a unit is in the denominator, substitute its definition directly: 1dL=10.1 L=10 L−1\frac{1}{\text{dL}} = \frac{1}{0.1\text{ L}} = 10\text{ L}^{-1}.

  • Always write the fractional units explicitly with dimensional analysis (for example, 10 dL1 L\frac{10\text{ dL}}{1\text{ L}}) to verify that the target unit cancels into the correct position.

CORRECTED PATH
ACEpath Teacher's Demonstration
  1. Write the unit conversion using dimensional analysis: 1\text{ \frac{mg}{dL}} \times \frac{10\text{ dL}}{1\text{ L}} \times \frac{1\text{ mmol}}{180.16\text{ mg}} = \frac{10}{180.16}\text{ mmol/L}.

  2. Multiply the entire empirical model by the corrected factor: CSI(v)=10180.16(250−0.8v)C_{\text{SI}}(v) = \frac{10}{180.16}(250 - 0.8v).

  3. Distribute and evaluate the coefficients: 2500180.16≈13.88\frac{2500}{180.16} \approx 13.88 and −8180.16v≈−0.0444v-\frac{8}{180.16}v \approx -0.0444v.

Final answer

CSI(v)=10180.16(250−0.8v)≈13.88−0.0444v mmol/LC_{\text{SI}}(v) = \frac{10}{180.16}(250 - 0.8v) \approx 13.88 - 0.0444v\text{ mmol/L}

NEXT STEPS
Final Takeaways from Your Teacher
  • Practice converting compound units with prefixes in the denominator by explicitly writing out canceling fractions.

  • Check that your final concentrations make physical sense: since a liter is 1010 times larger than a deciliter, a liter contains 1010 times as much solute mass.

OverviewACEpath Teacher's Diagnosis

02 The student converts only the constant term and neglects to distribute the unit conversion factor to the slope term with v.

Sample Student Work

Reviewed by ACEpath Teacher
Step-by-Step Review
Walk Through It with Your Teacher
Incorrect
  1. Step 1

    1 mg/dL=10 mg/L  ⟹  Conversion factor=10180.16≈0.055511\text{ mg/dL} = 10\text{ mg/L} \implies \text{Conversion factor} = \frac{10}{180.16} \approx 0.05551

  2. Step 2

    CSI(v)=250×0.05551−0.8vC_{\text{SI}}(v) = 250 \times 0.05551 - 0.8v

    Correct

    CSI(v)=10180.16(250−0.8v)C_{\text{SI}}(v) = \frac{10}{180.16}(250 - 0.8v)

    Because the entire function output C(v)C(v) is measured in mg/dL\text{mg/dL}, the conversion factor must scale the entire expression (250−0.8v)(250 - 0.8v), not just the constant term 250250.

  3. Step 3

    CSI(v)=13.88−0.8vC_{\text{SI}}(v) = 13.88 - 0.8v

    Correct

    CSI(v)≈13.88−0.0444v mmol/LC_{\text{SI}}(v) \approx 13.88 - 0.0444v\text{ mmol/L}

    This result follows directly from not distributing the conversion factor to the slope term in the previous step.

WHAT YOU DID WELL
Compliments from Your Teacher

You correctly converted deciliters to liters by scaling by 1010.

You correctly used the solute molar mass to convert milligrams into millimoles.

THE ERROR
Where Your ACEpath Teacher Spotted the Mistake
Partial unit conversion / failure to distribute scale factor

You treated the constant 250250 as the only term carrying units, forgetting that the slope term 0.8v0.8v also has units of concentration.

WHY IT HAPPENED
ACEpath Teacher's Diagnosis

Confusing a function transformation ynew=k⋅f(x)y_{\text{new}} = k \cdot f(x) with converting an isolated constant value. When converting the dependent variable of a formula, the scale factor must multiply every term in the expression.

REASONING PATH
Your ACEpath teacher’s suggested approach
Scaling a Dependent Variable
  • If y=f(x)y = f(x) and ynew=k⋅yy_{\text{new}} = k \cdot y, then ynew=k⋅[f(x)]y_{\text{new}} = k \cdot [f(x)].

  • Always wrap the original right-hand side in parentheses before multiplying by the conversion factor.

Dimensional Homogeneity
  • Every added or subtracted term in an equation must carry the same overall dimension as the output.

  • Check that both the constant term (250250) and the rate term (0.8v0.8v) are scaled to the target output units.

CORRECTED PATH
ACEpath Teacher's Demonstration
  1. Multiply the entire formula by the conversion factor: CSI(v)=10180.16(250−0.8v)C_{\text{SI}}(v) = \frac{10}{180.16}(250 - 0.8v)

  2. Distribute the factor to both terms: CSI(v)=2500180.16−8180.16vC_{\text{SI}}(v) = \frac{2500}{180.16} - \frac{8}{180.16}v

  3. Compute the decimal approximations: CSI(v)≈13.88−0.0444vC_{\text{SI}}(v) \approx 13.88 - 0.0444v

Final answer

CSI(v)=10180.16(250−0.8v)≈13.88−0.0444v mmol/LC_{\text{SI}}(v) = \frac{10}{180.16}(250 - 0.8v) \approx 13.88 - 0.0444v\text{ mmol/L}

NEXT STEPS
Final Takeaways from Your Teacher
  • Wrap the entire polynomial or linear expression in parentheses before applying a dependent-variable conversion factor.

  • Verify dimensional consistency by checking that the slope unit converts properly: (mg/dL)/(mL/min)→(mmol/L)/(mL/min)(\text{mg/dL})/(\text{mL/min}) \to (\text{mmol/L})/(\text{mL/min}).

OverviewACEpath Teacher's Diagnosis

03 The student multiplies by the molar mass instead of dividing by it when converting from mass (mg) to amount of substance (mmol).

Sample Student Work

Reviewed by ACEpath Teacher
Step-by-Step Review
Walk Through It with Your Teacher
Incorrect
  1. Step 1

    1 mg/dL=10 mg/L1\text{ mg/dL} = 10\text{ mg/L}

  2. Step 2

    Conversion to mmol: 1 mg=180.16 mmol\text{Conversion to mmol: } 1\text{ mg} = 180.16\text{ mmol}

    Correct

    1 mmol=180.16 mg  ⟹  1 mg=1180.16 mmol1\text{ mmol} = 180.16\text{ mg} \implies 1\text{ mg} = \frac{1}{180.16}\text{ mmol}

    A molar mass of 180.16 g/mol180.16\text{ g/mol} means that 1 mmol1\text{ mmol} weighs 180.16 mg180.16\text{ mg}. To convert milligrams into millimoles, you need to divide by 180.16180.16, not set 1 mg1\text{ mg} equal to 180.16 mmol180.16\text{ mmol}.

  3. Step 3

    Conversion factor=10×180.16=1801.6\text{Conversion factor} = 10 \times 180.16 = 1801.6

    Correct

    Conversion factor=10180.16≈0.05551 (mmol/L) per (mg/dL)\text{Conversion factor} = \frac{10}{180.16} \approx 0.05551\text{ (mmol/L) per (mg/dL)}

    Because of the inverted mole conversion from Step 2, you multiplied by 180.16180.16 instead of dividing by it.

  4. Step 4

    CSI(v)=1801.6×(250−0.8v)=450400−1441.28vC_{\text{SI}}(v) = 1801.6 \times (250 - 0.8v) = 450400 - 1441.28v

    Correct

    CSI(v)=10180.16(250−0.8v)≈13.88−0.0444vC_{\text{SI}}(v) = \frac{10}{180.16}(250 - 0.8v) \approx 13.88 - 0.0444v

    Your algebraic distribution across both terms of the linear function was carried out properly, but it used the incorrect scaling factor from Step 3.

WHAT YOU DID WELL
Compliments from Your Teacher

You correctly converted the volume dimension from deciliters to liters (1 dL=0.1 L1\text{ dL} = 0.1\text{ L}).

You correctly distributed the conversion factor across both terms of the linear function C(v)C(v).

THE ERROR
Where Your ACEpath Teacher Spotted the Mistake
Inverted dimensional factor (multiplied instead of divided by molar mass)

no

WHY IT HAPPENED
ACEpath Teacher's Diagnosis

You confused the direction of the molar mass ratio, assigning 180.16180.16 units of the smaller quantity (millimoles) to 11 unit of mass (milligram) rather than recalling that 1 mol=M grams1\text{ mol} = M\text{ grams}, or 1 mmol=180.16 mg1\text{ mmol} = 180.16\text{ mg}.

REASONING PATH
Your ACEpath teacher’s suggested approach
Dimensional Analysis Unit Cancellation
  • mmol=mg×1 mmolM mg\text{mmol} = \text{mg} \times \frac{1\text{ mmol}}{M\text{ mg}}

  • Always write out unit fractions so the unwanted unit cancels: mgdL×10 dL1 L×1 mmol180.16 mg\frac{\text{mg}}{\text{dL}} \times \frac{10\text{ dL}}{1\text{ L}} \times \frac{1\text{ mmol}}{180.16\text{ mg}}.

Magnitude Sanity Check
  • One mole (or millimole) contains a large mass in grams (or milligrams).

  • Since 1 mmol=180.16 mg1\text{ mmol} = 180.16\text{ mg}, 1 mg1\text{ mg} must be a small fraction of a millimole, not over 180 mmol180\text{ mmol}.

CORRECTED PATH
ACEpath Teacher's Demonstration
  1. Write the definition of molar mass: 1 mmol=180.16 mg1\text{ mmol} = 180.16\text{ mg}, which means 1 mg=1180.16 mmol1\text{ mg} = \frac{1}{180.16}\text{ mmol}.

  2. Combine the volume conversion (10 dL/L10\text{ dL/L}) and the molar conversion into one overall scaling factor: 1 mgdL=10180.16 mmol/L\frac{1\text{ mg}}{\text{dL}} = \frac{10}{180.16}\text{ mmol/L}.

  3. Multiply the entire empirical expression by this factor: CSI(v)=10180.16(250−0.8v)C_{\text{SI}}(v) = \frac{10}{180.16}(250 - 0.8v).

  4. Distribute and simplify: CSI(v)=2500180.16−8180.16v≈13.88−0.0444vC_{\text{SI}}(v) = \frac{2500}{180.16} - \frac{8}{180.16}v \approx 13.88 - 0.0444v.

Final answer

CSI(v)=10180.16(250−0.8v)≈13.88−0.0444v mmol/LC_{\text{SI}}(v) = \frac{10}{180.16}(250 - 0.8v) \approx 13.88 - 0.0444v\text{ mmol/L}

NEXT STEPS
Final Takeaways from Your Teacher
  • Set up conversions using multiplying fractions (factor-label method) so units visibly cancel numerator-to-denominator.

  • Perform a magnitude reality check after converting between mass and moles.

Lock it in

Similar question

01

A patient's blood glucose concentration is modeled by G(t)=120−5t mg/dLG(t) = 120 - 5t\text{ mg/dL}, where tt is in hours. Convert this function representation into g/L\text{g/L}.

Answer

G(t)=1.2−0.05t g/LG(t) = 1.2 - 0.05t\text{ g/L}. Key step: 1 mg/dL=10−3 g0.1 L=0.01 g/L1\text{ mg/dL} = \frac{10^{-3}\text{ g}}{0.1\text{ L}} = 0.01\text{ g/L}. Multiply the formula by 0.010.01: 0.01(120−5t)=1.2−0.05t0.01(120 - 5t) = 1.2 - 0.05t.

02

A reactor's solute concentration is given by S(x)=450−15x mg/dLS(x) = 450 - 15x\text{ mg/dL}, where xx is position in meters. Convert S(x)S(x) to molarity in mol/L\text{mol/L} for a solute with molar mass 90 g/mol90\text{ g/mol}.

Answer

S(x)=0.05−0.00167x mol/LS(x) = 0.05 - 0.00167x\text{ mol/L} (or 120−1600x mol/L\frac{1}{20} - \frac{1}{600}x\text{ mol/L}). Key step: 1 mg/dL=10 mg/L90,000 mg/mol=19000 mol/L1\text{ mg/dL} = \frac{10\text{ mg/L}}{90{,}000\text{ mg/mol}} = \frac{1}{9000}\text{ mol/L}. Distribute 19000\frac{1}{9000} into (450−15x)(450 - 15x) to get 4509000−159000x=0.05−1600x\frac{450}{9000} - \frac{15}{9000}x = 0.05 - \frac{1}{600}x.

03

A dynamic model describes effluent mass flow rate as R(t)=300−4t mg/dL⋅L/minR(t) = 300 - 4t\text{ mg/dL}\cdot\text{L/min}, representing a combined rate. Express R(t)R(t) purely in g/min\text{g/min}.

Answer

R(t)=3−0.04t g/minR(t) = 3 - 0.04t\text{ g/min}. Key step: Note that mg/dL⋅L/min=(10mgL)⋅(Lmin)=10 mg/min=0.01 g/min\text{mg/dL}\cdot\text{L/min} = \left(10\frac{\text{mg}}{\text{L}}\right)\cdot\left(\frac{\text{L}}{\text{min}}\right) = 10\text{ mg/min} = 0.01\text{ g/min}. Multiplying (300−4t)(300 - 4t) by 0.01 g/min0.01\text{ g/min} yields 3−0.04t g/min3 - 0.04t\text{ g/min}.

Loading workspace…