Resources

An environmental monitoring drone measures toxic nitrogen dioxide (NO2\text{NO}_2, molar mass M=46.01 g/molM = 46.01\text{ g/mol}) emissions from a factory flue stack. A gas sample chamber of fixed volume V=2.50×103 cm3V = 2.50\times 10^3\text{ cm}^3 collects exhaust gas at an internal temperature of T=25.0∘CT = 25.0^\circ\text{C} and pressure P=101.3 kPaP = 101.3\text{ kPa}. Municipal clean-air regulations require the concentration of NO2\text{NO}_2 to remain below 15.0 ppm15.0\text{ ppm} by volume (where 1 ppm=1 μL/L1\text{ ppm} = 1\,\mu\mathrm{L/L} under ideal gas conditions, R=8.314 J/(mol⋅K)R = 8.314\text{ J/(mol}\cdot\text{K)}). If analytical sensors record a total mass of 7.20×10−2 mg7.20\times 10^{-2}\text{ mg} of NO2\text{NO}_2 within the sample chamber, convert all quantities to coherent SI base units (textm3\\text{m}^3, Pa\text{Pa}, K\text{K}, mol\text{mol}), compute the total moles of gas ntotn_{\text{tot}} and moles of NO2\text{NO}_2 (npollutantn_{\text{pollutant}}), and determine whether the measured concentration in ppm\text{ppm} violates the municipal threshold constraint.

Answer and steps

Final answer

ntot=0.1022 moln_{\text{tot}} = 0.1022\text{ mol}; npollutant=1.565×10−6 moln_{\text{pollutant}} = 1.565\times 10^{-6}\text{ mol}; Concentration: 15.3 ppm15.3\text{ ppm}; Constraint status: Violates threshold (15.3 ppm>15.0 ppm15.3\text{ ppm} > 15.0\text{ ppm})

Steps

01

Convert all given quantities to SI base units

To apply standard physical formulas like the ideal gas law, convert all chamber conditions and pollutant measurements to coherent SI base units (m3\text{m}^3, Pa\text{Pa}, K\text{K}, g\text{g} or kg\text{kg}):

  • Volume (VV): Since 1 cm=10−2 m1\text{ cm} = 10^{-2}\text{ m}, 1 cm3=10−6 m31\text{ cm}^3 = 10^{-6}\text{ m}^3: V=2.50×103 cm3=2.50×103×10−6 m3=2.50×10−3 m3V = 2.50 \times 10^3\text{ cm}^3 = 2.50 \times 10^3 \times 10^{-6}\text{ m}^3 = 2.50 \times 10^{-3}\text{ m}^3
  • Pressure (PP): P=101.3 kPa=101.3×103 Pa=1.013×105 PaP = 101.3\text{ kPa} = 101.3 \times 10^3\text{ Pa} = 1.013 \times 10^5\text{ Pa}
  • Temperature (TT): Convert from degrees Celsius to kelvins: T=25.0+273.15=298.15 KT = 25.0 + 273.15 = 298.15\text{ K}
  • Mass of NOX2\ce{NO2} (mm): Convert from milligrams to grams: m=7.20×10−2 mg=7.20×10−5 gm = 7.20 \times 10^{-2}\text{ mg} = 7.20 \times 10^{-5}\text{ g}

02

Compute the total moles of exhaust gas (ntotn_{\text{tot}})

Using the ideal gas equation of state PV=ntotRTPV = n_{\text{tot}}RT:

ntot=PVRTn_{\text{tot}} = \frac{PV}{RT}

Substitute the SI values into the equation:

ntot=(1.013×105 Pa)(2.50×10−3 m3)(8.314 J/(mol⋅K))(298.15 K)=253.252478.82≈0.1022 moln_{\text{tot}} = \frac{(1.013 \times 10^5\text{ Pa})(2.50 \times 10^{-3}\text{ m}^3)}{(8.314\text{ J/(mol}\cdot\text{K)})(298.15\text{ K})} = \frac{253.25}{2478.82} \approx 0.1022\text{ mol}


03

Compute the moles of NOX2\ce{NO2} (npollutantn_{\text{pollutant}})

The moles of nitrogen dioxide are found from its recorded mass and molar mass (M=46.01 g/molM = 46.01\text{ g/mol}):

npollutant=mM=7.20×10−5 g46.01 g/mol≈1.565×10−6 moln_{\text{pollutant}} = \frac{m}{M} = \frac{7.20 \times 10^{-5}\text{ g}}{46.01\text{ g/mol}} \approx 1.565 \times 10^{-6}\text{ mol}


04

Calculate the concentration in ppm\text{ppm} and verify constraints

By Avogadro's law, for an ideal gas mixture, volume fraction is equivalent to mole fraction. Thus, the concentration in parts per million (ppm\text{ppm}) is given by:

Concentration (ppm)=npollutantntot×106\text{Concentration (ppm)} = \frac{n_{\text{pollutant}}}{n_{\text{tot}}} \times 10^6

Substitute the molar values:

Concentration=1.565×10−6 mol0.1022 mol×106≈15.3 ppm\text{Concentration} = \frac{1.565 \times 10^{-6}\text{ mol}}{0.1022\text{ mol}} \times 10^6 \approx 15.3\text{ ppm}

Constraint Evaluation:

  • Municipal regulatory threshold: ≤15.0 ppm\le 15.0\text{ ppm}
  • Measured value: 15.3 ppm15.3\text{ ppm}

Because 15.3 ppm>15.0 ppm15.3\text{ ppm} > 15.0\text{ ppm}, the sample violates the threshold.

Typical errors

OverviewACEpath Teacher's Diagnosis

01 The student forgets to convert Celsius to Kelvin when applying the ideal gas law, leading to an underestimated total number of moles and an inflated ppm value.

Sample Student Work

Reviewed by ACEpath Teacher
Step-by-Step Review
Walk Through It with Your Teacher
Incorrect
  1. Step 1

    V=2.50×10−3 m3V = 2.50 \times 10^{-3}\text{ m}^3, P=101300 PaP = 101300\text{ Pa}, T=25.0 KT = 25.0\text{ K}, m=7.20×10−5 gm = 7.20 \times 10^{-5}\text{ g}

    Correct

    V=2.50×10−3 m3V = 2.50 \times 10^{-3}\text{ m}^3, P=1.013×105 PaP = 1.013 \times 10^5\text{ Pa}, T=25.0+273.15=298.15 KT = 25.0 + 273.15 = 298.15\text{ K}, m=7.20×10−5 gm = 7.20 \times 10^{-5}\text{ g}

    You converted volume, pressure, and mass accurately, but you treated 25.0∘C25.0^\circ\text{C} directly as 25.0 K25.0\text{ K}. Absolute temperature in SI formulas must be expressed in kelvins using T(K)=T(∘C)+273.15T(\text{K}) = T(^\circ\text{C}) + 273.15, giving 298.15 K298.15\text{ K}.

  2. Step 2

    ntot=101300×2.50×10−38.314×25.0=1.218 moln_{\text{tot}} = \frac{101300 \times 2.50 \times 10^{-3}}{8.314 \times 25.0} = 1.218\text{ mol}

    Correct

    ntot=(1.013×105 Pa)(2.50×10−3 m3)(8.314 J/(mol⋅K))(298.15 K)≈0.1022 moln_{\text{tot}} = \frac{(1.013 \times 10^5\text{ Pa})(2.50 \times 10^{-3}\text{ m}^3)}{(8.314\text{ J/(mol}\cdot\text{K)})(298.15\text{ K})} \approx 0.1022\text{ mol}

    You set up the ideal gas equation correctly as n=PVRTn = \frac{PV}{RT}, but using 25.0 K25.0\text{ K} instead of 298.15 K298.15\text{ K} produced an inflated mole count of 1.218 mol1.218\text{ mol}.

  3. Step 3

    npollutant=7.20×10−546.01=1.565×10−6 moln_{\text{pollutant}} = \frac{7.20 \times 10^{-5}}{46.01} = 1.565 \times 10^{-6}\text{ mol}

  4. Step 4

    ppm=1.565×10−61.218×106=1.28 ppm⟹1.28 ppm<15.0 ppm\text{ppm} = \frac{1.565 \times 10^{-6}}{1.218} \times 10^6 = 1.28\text{ ppm} \Longrightarrow 1.28\text{ ppm} < 15.0\text{ ppm}, so it does not violate the threshold.

    Correct

    ppm=1.565×10−6 mol0.1022 mol×106≈15.3 ppm⟹15.3 ppm>15.0 ppm\text{ppm} = \frac{1.565 \times 10^{-6}\text{ mol}}{0.1022\text{ mol}} \times 10^6 \approx 15.3\text{ ppm} \Longrightarrow 15.3\text{ ppm} > 15.0\text{ ppm}, so the sample violates the threshold.

    Your ratio calculation method was correct, but dividing by your inflated total mole value gave 1.28 ppm1.28\text{ ppm} rather than the true value of 15.3 ppm15.3\text{ ppm}, which flips the threshold determination.

WHAT YOU DID WELL
Compliments from Your Teacher

You converted cubic centimeters to cubic meters, kilopascals to pascals, and milligrams to grams with complete accuracy.

You correctly selected and rearranged the ideal gas equation PV=nRTPV = nRT.

You accurately found the moles of NO2\text{NO}_2 from mass and molar mass.

You correctly defined parts-per-million by volume as the mole fraction multiplied by 10610^6.

THE ERROR
Where Your ACEpath Teacher Spotted the Mistake
Temperature Unit Conversion Error

no

WHY IT HAPPENED
ACEpath Teacher's Diagnosis

You replaced the Celsius degree symbol with kelvins without applying the additive temperature offset T(K)=T(∘C)+273.15T(\text{K}) = T(^\circ\text{C}) + 273.15, treating temperature as if Celsius and Kelvin share a common zero point.

REASONING PATH
Your ACEpath teacher’s suggested approach
Absolute Temperature in the Ideal Gas Law
  • Thermodynamic equations of state require temperature on an absolute scale where zero corresponds to absolute zero: T(K)=T(∘C)+273.15T(\text{K}) = T(^\circ\text{C}) + 273.15.

  • Always add 273.15273.15 to temperatures given in Celsius before substituting into PV=nRTPV = nRT.

CORRECTED PATH
ACEpath Teacher's Demonstration
  1. Recalculate ntotn_{\text{tot}} using the absolute temperature T=298.15 KT = 298.15\text{ K}: ntot=(1.013×105 Pa)(2.50×10−3 m3)(8.314 J/(mol⋅K))(298.15 K)=253.252478.82≈0.1022 moln_{\text{tot}} = \frac{(1.013 \times 10^5\text{ Pa})(2.50 \times 10^{-3}\text{ m}^3)}{(8.314\text{ J/(mol}\cdot\text{K)})(298.15\text{ K})} = \frac{253.25}{2478.82} \approx 0.1022\text{ mol}.

  2. Recalculate the pollutant concentration using the correct total moles: ppm=1.565×10−6 mol0.1022 mol×106≈15.3 ppm\text{ppm} = \frac{1.565 \times 10^{-6}\text{ mol}}{0.1022\text{ mol}} \times 10^6 \approx 15.3\text{ ppm}.

  3. Evaluate the municipal threshold constraint: 15.3 ppm>15.0 ppm15.3\text{ ppm} > 15.0\text{ ppm}.

Final answer

ntot=0.1022 moln_{\text{tot}} = 0.1022\text{ mol}; npollutant=1.565×10−6 moln_{\text{pollutant}} = 1.565 \times 10^{-6}\text{ mol}; Concentration: 15.3 ppm15.3\text{ ppm}; Constraint status: Violates threshold (15.3 ppm>15.0 ppm15.3\text{ ppm} > 15.0\text{ ppm})

NEXT STEPS
Final Takeaways from Your Teacher
  • Flag temperature units during your initial variable list to confirm that degrees Celsius are converted to kelvins before substituting into state equations.

  • Perform a quick sanity check on gas moles at standard ambient conditions: 1 mol1\text{ mol} occupies roughly 24.5 L24.5\text{ L} at room temperature, so a 2.5 L2.5\text{ L} chamber should contain approximately 0.1 mol0.1\text{ mol}, not over 1 mol1\text{ mol}.

OverviewACEpath Teacher's Diagnosis

02 The student misconverts cubic centimeters to cubic meters by using 10⁻² or 10⁻⁴ instead of 10⁻⁶, drastically miscalculating the total moles of gas.

Sample Student Work

Reviewed by ACEpath Teacher
Step-by-Step Review
Walk Through It with Your Teacher
Incorrect
  1. Step 1

    V=2.50×103×10−4 m3=0.250 m3V = 2.50 \times 10^3 \times 10^{-4}\text{ m}^3 = 0.250\text{ m}^3 ⟹ P=1.013×105 PaP = 1.013 \times 10^5\text{ Pa} ⟹ T=25.0+273.15=298.15 KT = 25.0 + 273.15 = 298.15\text{ K} ⟹ m=7.20×10−5 gm = 7.20 \times 10^{-5}\text{ g}

    Correct

    V=2.50×103×10−6 m3=2.50×10−3 m3V = 2.50 \times 10^3 \times 10^{-6}\text{ m}^3 = 2.50 \times 10^{-3}\text{ m}^3, P=1.013×105 PaP = 1.013 \times 10^5\text{ Pa}, T=298.15 KT = 298.15\text{ K}, m=7.20×10−5 gm = 7.20 \times 10^{-5}\text{ g}

    You correctly converted temperature to kelvins, pressure to pascals, and mass to grams. However, because 1 cm=10−2 m1\text{ cm} = 10^{-2}\text{ m}, the cubic conversion requires cubing the linear factor: 1 cm3=(10−2 m)3=10−6 m31\text{ cm}^3 = (10^{-2}\text{ m})^3 = 10^{-6}\text{ m}^3. You multiplied by 10−410^{-4} (the conversion factor for area, cm2\text{cm}^2), making your volume 100100 times too large.

  2. Step 2

    ntot=1.013×105×0.2508.314×298.15=10.22 moln_{\text{tot}} = \frac{1.013 \times 10^5 \times 0.250}{8.314 \times 298.15} = 10.22\text{ mol}

    Correct

    ntot=(1.013×105 Pa)(2.50×10−3 m3)(8.314 J/(mol⋅K))(298.15 K)≈0.1022 moln_{\text{tot}} = \frac{(1.013 \times 10^5\text{ Pa})(2.50 \times 10^{-3}\text{ m}^3)}{(8.314\text{ J/(mol}\cdot\text{K)})(298.15\text{ K})} \approx 0.1022\text{ mol}

    You correctly selected and applied the ideal gas equation ntot=PVRTn_{\text{tot}} = \frac{PV}{RT}. Your numerical calculation is algebraically consistent with your volume from Step 1, but the result is 100100 times too large due to the volume conversion error.

  3. Step 3

    npollutant=7.20×10−546.01=1.565×10−6 moln_{\text{pollutant}} = \frac{7.20 \times 10^{-5}}{46.01} = 1.565 \times 10^{-6}\text{ mol}

  4. Step 4

    ppm=(1.565×10−610.22)×106=0.153 ppm\text{ppm} = \left(\frac{1.565 \times 10^{-6}}{10.22}\right) \times 10^6 = 0.153\text{ ppm} ⟹ 0.153 ppm<15.0 ppm0.153\text{ ppm} < 15.0\text{ ppm}, so it does not violate the threshold.

    Correct

    ppm=(1.565×10−6 mol0.1022 mol)×106≈15.3 ppm\text{ppm} = \left(\frac{1.565 \times 10^{-6}\text{ mol}}{0.1022\text{ mol}}\right) \times 10^6 \approx 15.3\text{ ppm} ⟹ 15.3 ppm>15.0 ppm15.3\text{ ppm} > 15.0\text{ ppm}, so the sample violates the threshold constraint.

    Your formula for concentration in ppm\text{ppm} and your threshold comparison logic were completely correct. However, because ntotn_{\text{tot}} was overestimated by a factor of 100100, your calculated concentration was 100100 times too low, reversing the constraint conclusion.

WHAT YOU DID WELL
Compliments from Your Teacher

You correctly converted temperature from Celsius to Kelvin and pressure from kilopascals to pascals.

You correctly identified and applied the ideal gas law PV=nRTPV = nRT to model total moles of gas.

You accurately calculated the moles of pollutant using molar mass.

You correctly defined concentration in parts per million as the mole fraction multiplied by 10610^6.

THE ERROR
Where Your ACEpath Teacher Spotted the Mistake
Derived Unit Volume Conversion Error

no

WHY IT HAPPENED
ACEpath Teacher's Diagnosis

You applied the area conversion factor 1 cm2=(10−2 m)2=10−4 m21\text{ cm}^2 = (10^{-2}\text{ m})^2 = 10^{-4}\text{ m}^2 to a volume quantity instead of cubing the linear metric prefix (10−2 m)3=10−6 m3(10^{-2}\text{ m})^3 = 10^{-6}\text{ m}^3.

REASONING PATH
Your ACEpath teacher’s suggested approach
Derive Derived Unit Exponents
  • When converting units with powers, raise both the base conversion and the unit to that power: (10k unit)p=10k⋅p unitp(10^k\text{ unit})^p = 10^{k \cdot p}\text{ unit}^p.

  • Always write (1 cm)3=(10−2 m)3=10−6 m3(1\text{ cm})^3 = (10^{-2}\text{ m})^3 = 10^{-6}\text{ m}^3 explicitly before substituting into formulas.

CORRECTED PATH
ACEpath Teacher's Demonstration
  1. V=2.50×103 cm3×(10−2 m/cm)3=2.50×10−3 m3V = 2.50 \times 10^3\text{ cm}^3 \times \left(10^{-2}\text{ m/cm}\right)^3 = 2.50 \times 10^{-3}\text{ m}^3

  2. ntot=PVRT=(1.013×105 Pa)(2.50×10−3 m3)(8.314 J/(mol⋅K))(298.15 K)≈0.1022 moln_{\text{tot}} = \frac{PV}{RT} = \frac{(1.013 \times 10^5\text{ Pa})(2.50 \times 10^{-3}\text{ m}^3)}{(8.314\text{ J/(mol}\cdot\text{K)})(298.15\text{ K})} \approx 0.1022\text{ mol}

  3. Concentration=1.565×10−6 mol0.1022 mol×106≈15.3 ppm\text{Concentration} = \frac{1.565 \times 10^{-6}\text{ mol}}{0.1022\text{ mol}} \times 10^6 \approx 15.3\text{ ppm}

  4. Compare to regulatory limit: 15.3 ppm>15.0 ppm15.3\text{ ppm} > 15.0\text{ ppm}

Final answer

ntot=0.1022 moln_{\text{tot}} = 0.1022\text{ mol}; npollutant=1.565×10−6 moln_{\text{pollutant}} = 1.565 \times 10^{-6}\text{ mol}; Concentration: 15.3 ppm15.3\text{ ppm}; Constraint status: Violates threshold (15.3 ppm>15.0 ppm15.3\text{ ppm} > 15.0\text{ ppm})

NEXT STEPS
Final Takeaways from Your Teacher
  • Practice converting derived volume and density units by explicitly expanding powers of linear metric prefixes.

  • Re-evaluate ideal gas problem constraints after checking that all base variables match SI units (m3\text{m}^3, Pa\text{Pa}, K\text{K}).

OverviewACEpath Teacher's Diagnosis

03 The student treats the mass given in milligrams as grams directly without dividing by 1000, overestimating pollutant moles by a factor of 1000.

Sample Student Work

Reviewed by ACEpath Teacher
Step-by-Step Review
Walk Through It with Your Teacher
Incorrect
  1. Step 1

    V=2.50×10−3 m3V = 2.50 \times 10^{-3}\text{ m}^3 ⟹ P=1.013×105 PaP = 1.013 \times 10^5\text{ Pa} ⟹ T=298.15 KT = 298.15\text{ K} ⟹ m=7.20×10−2 gm = 7.20 \times 10^{-2}\text{ g}

    Correct

    V=2.50×10−3 m3V = 2.50 \times 10^{-3}\text{ m}^3, P=1.013×105 PaP = 1.013 \times 10^5\text{ Pa}, T=298.15 KT = 298.15\text{ K}, m=7.20×10−5 gm = 7.20 \times 10^{-5}\text{ g}

    You correctly converted volume, pressure, and temperature to coherent SI units. However, the problem gave the pollutant mass as 7.20×10−2 mg7.20 \times 10^{-2}\text{ mg}. Since 1 mg=10−3 g1\text{ mg} = 10^{-3}\text{ g}, the mass in grams is 7.20×10−2×10−3 g=7.20×10−5 g7.20 \times 10^{-2} \times 10^{-3}\text{ g} = 7.20 \times 10^{-5}\text{ g}.

  2. Step 2

    ntot=1.013×105×2.50×10−38.314×298.15=0.1022 moln_{\text{tot}} = \frac{1.013 \times 10^5 \times 2.50 \times 10^{-3}}{8.314 \times 298.15} = 0.1022\text{ mol}

  3. Step 3

    npollutant=7.20×10−246.01=1.565×10−3 moln_{\text{pollutant}} = \frac{7.20 \times 10^{-2}}{46.01} = 1.565 \times 10^{-3}\text{ mol}

    Correct

    npollutant=7.20×10−5 g46.01 g/mol≈1.565×10−6 moln_{\text{pollutant}} = \frac{7.20 \times 10^{-5}\text{ g}}{46.01\text{ g/mol}} \approx 1.565 \times 10^{-6}\text{ mol}

    Your division by the molar mass was algebraically correct, but because the mass was overestimated by a factor of 10001000, your result became 1.565×10−3 mol1.565 \times 10^{-3}\text{ mol} instead of 1.565×10−6 mol1.565 \times 10^{-6}\text{ mol}.

  4. Step 4

    ppm=1.565×10−30.1022×106=15313 ppm⟹15313 ppm>15.0 ppm\text{ppm} = \frac{1.565 \times 10^{-3}}{0.1022} \times 10^6 = 15313\text{ ppm} \Longrightarrow 15313\text{ ppm} > 15.0\text{ ppm}, so it violates the threshold.

    Correct

    ppm=1.565×10−6 mol0.1022 mol×106≈15.3 ppm⟹15.3 ppm>15.0 ppm\text{ppm} = \frac{1.565 \times 10^{-6}\text{ mol}}{0.1022\text{ mol}} \times 10^6 \approx 15.3\text{ ppm} \Longrightarrow 15.3\text{ ppm} > 15.0\text{ ppm}, so it violates the threshold.

    Your formula for concentration in ppm\text{ppm} and your threshold comparison logic were completely sound, but propagating the earlier mass error produced 15313 ppm15313\text{ ppm} instead of 15.3 ppm15.3\text{ ppm}.

WHAT YOU DID WELL
Compliments from Your Teacher

You correctly converted volume from cm3\text{cm}^3 to m3\text{m}^3, pressure from kPa\text{kPa} to Pa\text{Pa}, and temperature from degrees Celsius to kelvins.

You applied the ideal gas equation PV=ntotRTPV = n_{\text{tot}}RT accurately to find total moles.

You used the correct relationship between mole fraction and parts per million (ppm\text{ppm}).

You compared the final concentration value against the threshold constraint with sound logic.

THE ERROR
Where Your ACEpath Teacher Spotted the Mistake
Metric prefix unit conversion error (mg to g)

You swapped the unit symbol from mg\text{mg} to g\text{g} without applying the metric factor 10−310^{-3}.

WHY IT HAPPENED
ACEpath Teacher's Diagnosis

Conflating metric prefixes with base units when substituting mass into molar mass formulas. Molar mass is expressed in g/mol\text{g/mol}, so a given mass in milligrams (mg\text{mg}) must be explicitly multiplied by 10−3 g/mg10^{-3}\text{ g/mg} before dividing by MM.

REASONING PATH
Your ACEpath teacher’s suggested approach
SI and Metric Prefix Consistency
  • 1 mg=10−3 g=10−6 kg1\text{ mg} = 10^{-3}\text{ g} = 10^{-6}\text{ kg}

  • Whenever a value has a prefix like milli- (10−310^{-3}) or micro- (10−610^{-6}), write out the power of ten explicitly before performing calculations.

CORRECTED PATH
ACEpath Teacher's Demonstration
  1. m=7.20×10−2 mg=7.20×10−5 gm = 7.20 \times 10^{-2}\text{ mg} = 7.20 \times 10^{-5}\text{ g}

  2. npollutant=7.20×10−5 g46.01 g/mol≈1.565×10−6 moln_{\text{pollutant}} = \frac{7.20 \times 10^{-5}\text{ g}}{46.01\text{ g/mol}} \approx 1.565 \times 10^{-6}\text{ mol}

  3. Concentration=1.565×10−6 mol0.1022 mol×106≈15.3 ppm\text{Concentration} = \frac{1.565 \times 10^{-6}\text{ mol}}{0.1022\text{ mol}} \times 10^6 \approx 15.3\text{ ppm}

  4. 15.3 ppm>15.0 ppm15.3\text{ ppm} > 15.0\text{ ppm}, so the sample violates the threshold.

Final answer

ntot=0.1022 moln_{\text{tot}} = 0.1022\text{ mol}; npollutant=1.565×10−6 moln_{\text{pollutant}} = 1.565\times 10^{-6}\text{ mol}; Concentration: 15.3 ppm15.3\text{ ppm}; Constraint status: Violates threshold (15.3 ppm>15.0 ppm15.3\text{ ppm} > 15.0\text{ ppm})

NEXT STEPS
Final Takeaways from Your Teacher
  • Always write out the unit conversion factor explicitly as a separate step before substituting into formulas.

  • Double-check that the mass units in mm (grams) match the mass units in molar mass MM (grams per mole).

Lock it in

Similar question

01

A weather balloon collects gas at an altitude where T=−13.0∘CT = -13.0^\circ\text{C}, P=50.0 kPaP = 50.0\text{ kPa}, and volume V=4.00×10−3 m3V = 4.00\times 10^{-3}\text{ m}^3. Calculate the total moles of gas in the balloon (R=8.314 J/(mol⋅K)R = 8.314\text{ J/(mol}\cdot\text{K)}).

Answer

n=0.0925 moln = 0.0925\text{ mol}. Key steps: Convert temperature to kelvins: T=−13.0+273.15=260.15 KT = -13.0 + 273.15 = 260.15\text{ K}. Convert pressure: P=50.0×103 Pa=5.00×104 PaP = 50.0\times 10^3\text{ Pa} = 5.00\times 10^4\text{ Pa}. Substitute into n=PVRT=(5.00×104)(4.00×10−3)(8.314)(260.15)=2002162.89≈0.0925 moln = \frac{PV}{RT} = \frac{(5.00\times 10^4)(4.00\times 10^{-3})}{(8.314)(260.15)} = \frac{200}{2162.89} \approx 0.0925\text{ mol}.

02

An industrial exhaust chamber of volume V=5.00 m3V = 5.00\text{ m}^3 operates at T=127.0∘CT = 127.0^\circ\text{C} and P=1.00×105 PaP = 1.00\times 10^5\text{ Pa}. The chamber contains 3.00×10−3 mol3.00\times 10^{-3}\text{ mol} of sulfur dioxide (SO2\text{SO}_2). Find the total moles of exhaust gas and the concentration of SO2\text{SO}_2 in parts per million (ppm\text{ppm}).

Answer

ntot=150.3 moln_{\text{tot}} = 150.3\text{ mol}, concentration ≈20.0 ppm\approx 20.0\text{ ppm}. Key steps: Convert temperature: T=127.0+273.15=400.15 KT = 127.0 + 273.15 = 400.15\text{ K}. Compute total moles: ntot=(1.00×105 Pa)(5.00 m3)(8.314 J/(mol⋅K))(400.15 K)≈150.3 moln_{\text{tot}} = \frac{(1.00\times 10^5\text{ Pa})(5.00\text{ m}^3)}{(8.314\text{ J/(mol}\cdot\text{K)})(400.15\text{ K})} \approx 150.3\text{ mol}. Compute concentration: ppm=npollutantntot×106=3.00×10−3150.3×106≈19.96 ppm≈20.0 ppm\text{ppm} = \frac{n_{\text{pollutant}}}{n_{\text{tot}}}\times 10^6 = \frac{3.00\times 10^{-3}}{150.3}\times 10^6 \approx 19.96\text{ ppm} \approx 20.0\text{ ppm}.

03

A safety sensor samples air in a storage room at 22.0∘C22.0^\circ\text{C} and 100.0 kPa100.0\text{ kPa} inside a 1.20×10−2 m31.20\times 10^{-2}\text{ m}^3 cylinder. The occupational safety limit for carbon monoxide (CO\text{CO}, M=28.01 g/molM = 28.01\text{ g/mol}) is 35.0 ppm35.0\text{ ppm}. If the sensor registers 0.500 mg0.500\text{ mg} of CO\text{CO}, does the concentration exceed the limit?

Answer

Yes, concentration is 36.4 ppm36.4\text{ ppm}, which violates the 35.0 ppm35.0\text{ ppm} limit. Key steps: Absolute temperature T=22.0+273.15=295.15 KT = 22.0 + 273.15 = 295.15\text{ K}. Total air moles ntot=(1.000×105)(1.20×10−2)(8.314)(295.15)≈0.4890 moln_{\text{tot}} = \frac{(1.000\times 10^5)(1.20\times 10^{-2})}{(8.314)(295.15)} \approx 0.4890\text{ mol}. Moles of CO\text{CO}: m=5.00×10−4 gm = 5.00\times 10^{-4}\text{ g}, nCO=5.00×10−4 g28.01 g/mol≈1.785×10−5 moln_{\text{CO}} = \frac{5.00\times 10^{-4}\text{ g}}{28.01\text{ g/mol}} \approx 1.785\times 10^{-5}\text{ mol}. Concentration: ppm=1.785×10−50.4890×106≈36.4 ppm>35.0 ppm\text{ppm} = \frac{1.785\times 10^{-5}}{0.4890}\times 10^6 \approx 36.4\text{ ppm} > 35.0\text{ ppm}.

Loading workspace…