Resources

An analytical chemist evaluates a green precipitation-filtration process designed to treat electroplating effluent by removing nickel ions as nickel dimethylglyoximate, Ni(C4H7N2O2)2\text{Ni(C}_4\text{H}_7\text{N}_2\text{O}_2)_2 (molar mass 288.91 g/mol288.91\text{ g/mol}). To standardize the residual nickel concentration in the effluent after treatment, a 100.0 mL100.0\text{ mL} aliquot of the treated wastewater is buffered to pH=10.00\text{pH} = 10.00 and titrated with a standard 0.01250 M0.01250\text{ M} disodium EDTA (Na2H2Y\text{Na}_2\text{H}_2\text{Y}) solution using murexide indicator. The titration requires exactly 18.40 mL18.40\text{ mL} of the EDTA solution to reach the purple-to-blue end point via the 1:11:1 complexation reaction Ni2++Y4−→[NiY]2−\text{Ni}^{2+} + \text{Y}^{4-} \rightarrow [\text{NiY}]^{2-}. If the untreated effluent initially contained 850.0 mg/L850.0\text{ mg/L} of Ni2+\text{Ni}^{2+} (molar mass 58.69 g/mol58.69\text{ g/mol}), calculate: (a) the concentration of residual Ni2+\text{Ni}^{2+} in the treated effluent in mg/L\text{mg/L}, and (b) the overall percentage reduction in nickel emission achieved by the green treatment process.

Answer and steps

Final answer

(a) Residual [Ni2+]=135.0 mg/L[\text{Ni}^{2+}] = 135.0\text{ mg/L}; (b) Nickel emission reduction =84.12%= 84.12\%

Steps

Part (a): Determine the Residual NiX2+\ce{Ni^{2+}} Concentration

  1. Calculate the moles of EDTA\ce{EDTA} consumed:
    The titration reaction follows a 1:11:1 stoichiometric ratio between NiX2+\ce{Ni^{2+}} and EDTA\ce{EDTA} (YX4−\ce{Y^{4-}}): NiX2++YX4−→[NiY]X2−\ce{Ni^2+ + Y^4- -> [NiY]^2-} Using the molarity (CC) and volume (VV) of the standard EDTA\ce{EDTA} solution: nEDTA=CEDTA⋅VEDTAn_{\ce{EDTA}} = C_{\ce{EDTA}} \cdot V_{\ce{EDTA}} nEDTA=0.01250 mol/L⋅(18.40×10−3 L)=2.300×10−4 moln_{\ce{EDTA}} = 0.01250\text{ mol/L} \cdot (18.40 \times 10^{-3}\text{ L}) = 2.300 \times 10^{-4}\text{ mol}
  2. Find the mass of NiX2+\ce{Ni^{2+}} present in the 100.0 mL100.0\text{ mL} aliquot:
    Because the stoichiometric ratio is 1:11:1, the moles of nickel ions titrated equal the moles of EDTA\ce{EDTA}: nNiX2+=nEDTA=2.300×10−4 moln_{\ce{Ni^2+}} = n_{\ce{EDTA}} = 2.300 \times 10^{-4}\text{ mol} Using the atomic molar mass of nickel (M=58.69 g/molM = 58.69\text{ g/mol}): mNiX2+=nNiX2+⋅MNim_{\ce{Ni^2+}} = n_{\ce{Ni^2+}} \cdot M_{\ce{Ni}} mNiX2+=2.300×10−4 mol⋅58.69 g/mol=0.0134987 g=13.4987 mgm_{\ce{Ni^2+}} = 2.300 \times 10^{-4}\text{ mol} \cdot 58.69\text{ g/mol} = 0.0134987\text{ g} = 13.4987\text{ mg}
  3. Calculate the concentration of residual NiX2+\ce{Ni^{2+}} in mg/L\text{mg/L}:
    Divide the mass in milligrams by the aliquot volume converted to liters (Valiquot=100.0 mL=0.1000 LV_{\text{aliquot}} = 100.0\text{ mL} = 0.1000\text{ L}): [NiX2+]treated=13.4987 mg0.1000 L=134.987 mg/L≈135.0 mg/L[\ce{Ni^2+}]_{\text{treated}} = \frac{13.4987\text{ mg}}{0.1000\text{ L}} = 134.987\text{ mg/L} \approx 135.0\text{ mg/L}

Part (b): Calculate the Percentage Reduction in Nickel Emission

  1. Apply the percentage reduction formula:
    The initial concentration of nickel in untreated effluent is Cinitial=850.0 mg/LC_{\text{initial}} = 850.0\text{ mg/L}, and the residual concentration after treatment is Cresidual=134.987 mg/LC_{\text{residual}} = 134.987\text{ mg/L}. Percentage Reduction=Cinitial−CresidualCinitial⋅100%\text{Percentage Reduction} = \frac{C_{\text{initial}} - C_{\text{residual}}}{C_{\text{initial}}} \cdot 100\%
  2. Compute the emission reduction: Percentage Reduction=850.0 mg/L−134.987 mg/L850.0 mg/L⋅100%\text{Percentage Reduction} = \frac{850.0\text{ mg/L} - 134.987\text{ mg/L}}{850.0\text{ mg/L}} \cdot 100\% Percentage Reduction=715.013 mg/L850.0 mg/L⋅100%≈84.12%\text{Percentage Reduction} = \frac{715.013\text{ mg/L}}{850.0\text{ mg/L}} \cdot 100\% \approx 84.12\%

Common Pitfall to Avoid

  • Molar Mass Selection: Be careful not to use the molar mass of the precipitation product, nickel dimethylglyoximate (288.91 g/mol288.91\text{ g/mol}), when calculating the dissolved NiX2+\ce{Ni^{2+}} mass in the titration. The titration measures elemental ionic nickel (NiX2+\ce{Ni^{2+}}), so only the atomic molar mass of nickel (58.69 g/mol58.69\text{ g/mol}) applies.

Typical errors

OverviewACEpath Teacher's Diagnosis

01 The student mistakenly uses the molar mass of nickel dimethylglyoximate (288.91 g/mol) instead of atomic nickel (58.69 g/mol) to calculate the mass of Ni²⁺ ions.

Sample Student Work

Reviewed by ACEpath Teacher
Step-by-Step Review
Walk Through It with Your Teacher
Incorrect
  1. Step 1

    n(EDTA)=0.01250 M×0.01840 L=2.300×10−4 mol  ⟹  n(NiX2+)=n(EDTA)=2.300×10−4 moln(\ce{EDTA}) = 0.01250\text{ M} \times 0.01840\text{ L} = 2.300 \times 10^{-4}\text{ mol} \implies n(\ce{Ni^{2+}}) = n(\ce{EDTA}) = 2.300 \times 10^{-4}\text{ mol}

  2. Step 2

    Mass of NiX2+=2.300×10−4 mol×288.91 g/mol=0.06645 g=66.45 mg\text{Mass of }\ce{Ni^{2+}} = 2.300 \times 10^{-4}\text{ mol} \times 288.91\text{ g/mol} = 0.06645\text{ g} = 66.45\text{ mg}

    Correct

    mNiX2+=2.300×10−4 mol×58.69 g/mol=0.01350 g=13.50 mgm_{\ce{Ni^{2+}}} = 2.300 \times 10^{-4}\text{ mol} \times 58.69\text{ g/mol} = 0.01350\text{ g} = 13.50\text{ mg}

    You multiplied by the molar mass of the solid complex Ni(CX4HX7NX2OX2)X2\ce{Ni(C4H7N2O2)2} (288.91 g/mol288.91\text{ g/mol}) rather than the atomic molar mass of dissolved nickel ions NiX2+\ce{Ni^{2+}} (58.69 g/mol58.69\text{ g/mol}).

  3. Step 3

    Residual NiX2+=66.45 mg0.1000 L=664.5 mg/L\text{Residual }\ce{Ni^{2+}} = \frac{66.45\text{ mg}}{0.1000\text{ L}} = 664.5\text{ mg/L}

    Correct

    [NiX2+]=13.4987 mg0.1000 L=135.0 mg/L[\ce{Ni^{2+}}] = \frac{13.4987\text{ mg}}{0.1000\text{ L}} = 135.0\text{ mg/L}

    Your formula and volume conversion were correct, but the concentration is incorrect due to the propagated mass error from Step 2.

  4. Step 4

    Percentage reduction=[850.0−664.5850.0]×100%=(185.5850.0)×100%=21.82%\text{Percentage reduction} = \left[\frac{850.0 - 664.5}{850.0}\right] \times 100\% = \left(\frac{185.5}{850.0}\right) \times 100\% = 21.82\%

    Correct

    Percentage reduction=850.0 mg/L−135.0 mg/L850.0 mg/L×100%=84.12%\text{Percentage reduction} = \frac{850.0\text{ mg/L} - 135.0\text{ mg/L}}{850.0\text{ mg/L}} \times 100\% = 84.12\%

    You set up the percentage reduction formula correctly, but using the incorrect residual concentration gave an emission reduction of 21.82%21.82\% instead of 84.12%84.12\%.

WHAT YOU DID WELL
Compliments from Your Teacher

You accurately calculated the amount of substance of EDTA\ce{EDTA} titrant consumed.

You recognized and applied the 1:11:1 stoichiometric equivalence between EDTA\ce{EDTA} and NiX2+\ce{Ni^{2+}}.

You correctly converted the aliquot volume from mL\text{mL} to L\text{L} and properly set up the percentage reduction equation.

THE ERROR
Where Your ACEpath Teacher Spotted the Mistake
Wrong molar mass selected

You accidentally picked the molar mass of the solid precipitate Ni(dmg)X2\ce{Ni(dmg)2} given in the problem text instead of the atomic mass of nickel.

WHY IT HAPPENED
ACEpath Teacher's Diagnosis

Confusing the species being quantified in the analytical measurement: while the treatment process precipitates nickel as Ni(CX4HX7NX2OX2)X2\ce{Ni(C4H7N2O2)2}, the post-filtration titration measures the unprecipitated, free NiX2+\ce{Ni^{2+}} ions remaining in solution.

REASONING PATH
Your ACEpath teacher’s suggested approach
Identify the Target Analyte
  • Titration with EDTA\ce{EDTA} directly chelates aqueous metal cations (here, NiX2+\ce{Ni^{2+}}). Converting moles of analyte to mass requires the molar mass of that specific ionic/atomic species, not the solid precipitate removed in the prior step.

  • Before multiplying nn by MM, explicitly write down the formula of the chemical species being converted: mNiX2+=nNiX2+⋅MNim_{\ce{Ni^{2+}}} = n_{\ce{Ni^{2+}}} \cdot M_{\ce{Ni}}.

CORRECTED PATH
ACEpath Teacher's Demonstration
  1. mNiX2+=2.300×10−4 mol×58.69 g/mol=0.013499 g=13.499 mgm_{\ce{Ni^{2+}}} = 2.300 \times 10^{-4}\text{ mol} \times 58.69\text{ g/mol} = 0.013499\text{ g} = 13.499\text{ mg}

  2. [NiX2+]=13.499 mg0.1000 L=135.0 mg/L[\ce{Ni^{2+}}] = \frac{13.499\text{ mg}}{0.1000\text{ L}} = 135.0\text{ mg/L}

  3. Percentage reduction=850.0 mg/L−134.99 mg/L850.0 mg/L×100%=84.12%\text{Percentage reduction} = \frac{850.0\text{ mg/L} - 134.99\text{ mg/L}}{850.0\text{ mg/L}} \times 100\% = 84.12\%

Final answer

(a) Residual [NiX2+]=135.0 mg/L[\ce{Ni^{2+}}] = 135.0\text{ mg/L}; (b) Nickel emission reduction =84.12%= 84.12\%

NEXT STEPS
Final Takeaways from Your Teacher
  • Review complexometric titration problems and double-check whether the question asks for the mass of the metal ion or the mass of the precipitate.

  • Practice identifying the exact chemical formula of the analyte at each stage of a multi-step separation process.

OverviewACEpath Teacher's Diagnosis

02 The student forgets to convert the 100.0 mL aliquot volume to liters, dividing the mass in mg by 100.0 mL directly and resulting in an incorrect concentration.

Sample Student Work

Reviewed by ACEpath Teacher
Step-by-Step Review
Walk Through It with Your Teacher
Incorrect
  1. Step 1

    n(NiX2+)=0.01250 mol/L×0.01840 L=2.300×10−4 moln(\ce{Ni^2+}) = 0.01250\text{ mol/L} \times 0.01840\text{ L} = 2.300 \times 10^{-4}\text{ mol}

  2. Step 2

    Mass of NiX2+=2.300×10−4 mol×58.69 g/mol=0.01350 g=13.50 mg\text{Mass of }\ce{Ni^2+} = 2.300 \times 10^{-4}\text{ mol} \times 58.69\text{ g/mol} = 0.01350\text{ g} = 13.50\text{ mg}

  3. Step 3

    Residual NiX2+=13.50 mg100.0 mL=0.1350 mg/L\text{Residual }\ce{Ni^2+} = \frac{13.50\text{ mg}}{100.0\text{ mL}} = 0.1350\text{ mg/L}

    Correct

    [NiX2+]residual=13.50 mg0.1000 L=135.0 mg/L[\ce{Ni^2+}]_{\text{residual}} = \frac{13.50\text{ mg}}{0.1000\text{ L}} = 135.0\text{ mg/L}

    You divided 13.50 mg13.50\text{ mg} by 100.0 mL100.0\text{ mL} but labeled the resulting unit as mg/L\text{mg/L}. Because 1 L=1000 mL1\text{ L} = 1000\text{ mL}, 100.0 mL=0.1000 L100.0\text{ mL} = 0.1000\text{ L}, making the concentration 135.0 mg/L135.0\text{ mg/L}.

  4. Step 4

    Percentage reduction=(850.0−0.1350850.0)×100%=(849.865850.0)×100%=99.98%\text{Percentage reduction} = \left(\frac{850.0 - 0.1350}{850.0}\right) \times 100\% = \left(\frac{849.865}{850.0}\right) \times 100\% = 99.98\%

    Correct

    Percentage reduction=(850.0−135.0850.0)×100%=84.12%\text{Percentage reduction} = \left(\frac{850.0 - 135.0}{850.0}\right) \times 100\% = 84.12\%

    Your percentage formula and arithmetic were correct, but the result was distorted by the incorrect residual concentration from Step 3.

WHAT YOU DID WELL
Compliments from Your Teacher

You correctly calculated the moles of complexed NiX2+\ce{Ni^2+} using the 1:11:1 stoichiometric ratio with standard EDTA\ce{EDTA}.

You used the atomic molar mass of nickel (58.69 g/mol58.69\text{ g/mol}) rather than the mass of the precipitate complex.

You set up the percentage reduction formula correctly.

THE ERROR
Where Your ACEpath Teacher Spotted the Mistake
Unit conversion omission

You divided milligrams by milliliters but directly wrote the unit as mg/L\text{mg/L} without converting the denominator.

WHY IT HAPPENED
ACEpath Teacher's Diagnosis

Overlooking dimensional consistency during concentration calculations, specifically treating milliliters as liters in the denominator.

REASONING PATH
Your ACEpath teacher’s suggested approach
Check Denominator Units
  • Concentration in mg/L\text{mg/L} requires volume in liters: C=mass (mg)V (L)C = \frac{\text{mass (mg)}}{V\text{ (L)}}.

  • Always convert sample aliquot volumes from mL\text{mL} to L\text{L} (VL=VmL1000V_{\text{L}} = \frac{V_{\text{mL}}}{1000}) before computing concentration.

CORRECTED PATH
ACEpath Teacher's Demonstration
  1. Convert the aliquot volume to liters: V=100.0 mL=0.1000 LV = 100.0\text{ mL} = 0.1000\text{ L}.

  2. Compute residual concentration: [NiX2+]residual=13.50 mg0.1000 L=135.0 mg/L[\ce{Ni^2+}]_{\text{residual}} = \frac{13.50\text{ mg}}{0.1000\text{ L}} = 135.0\text{ mg/L}.

  3. Calculate percentage reduction: 850.0 mg/L−135.0 mg/L850.0 mg/L×100%=715.0850.0×100%=84.12%\frac{850.0\text{ mg/L} - 135.0\text{ mg/L}}{850.0\text{ mg/L}} \times 100\% = \frac{715.0}{850.0} \times 100\% = 84.12\%.

Final answer

(a) 135.0 mg/L135.0\text{ mg/L}; (b) 84.12%84.12\%

NEXT STEPS
Final Takeaways from Your Teacher
  • Write out explicit unit cancellation factors when calculating concentrations: mgmL×1000 mL1 L=mg/L\frac{\text{mg}}{\text{mL}} \times \frac{1000\text{ mL}}{1\text{ L}} = \text{mg/L}.

  • Sanity check concentrations: dividing by 100 mL100\text{ mL} should yield a numerical value 1010 times larger in mg/L\text{mg/L}, not 100100 times smaller.

OverviewACEpath Teacher's Diagnosis

03 The student calculates the residual percentage remaining rather than the percentage reduction achieved by the treatment.

Sample Student Work

Reviewed by ACEpath Teacher
Step-by-Step Review
Walk Through It with Your Teacher
Partially correct
  1. Step 1

    n(EDTA)=0.01250 M×0.01840 L=2.300×10−4 mol  ⟹  n(NiX2+)=2.300×10−4 moln(\ce{EDTA}) = 0.01250\text{ M} \times 0.01840\text{ L} = 2.300 \times 10^{-4}\text{ mol} \implies n(\ce{Ni^{2+}}) = 2.300 \times 10^{-4}\text{ mol}

  2. Step 2

    Mass of NiX2+=2.300×10−4 mol×58.69 g/mol=13.50 mg  ⟹  Residual NiX2+=13.50 mg/0.1000 L=135.0 mg/L\text{Mass of }\ce{Ni^{2+}} = 2.300 \times 10^{-4}\text{ mol} \times 58.69\text{ g/mol} = 13.50\text{ mg} \implies \text{Residual }\ce{Ni^{2+}} = 13.50\text{ mg} / 0.1000\text{ L} = 135.0\text{ mg/L}

  3. Step 3

    Percentage=135.0 mg/L850.0 mg/L×100%  ⟹  Percentage reduction=15.88%\text{Percentage} = \frac{135.0\text{ mg/L}}{850.0\text{ mg/L}} \times 100\% \implies \text{Percentage reduction} = 15.88\%

    Correct

    Percentage reduction=Cinitial−CresidualCinitial×100%=850.0 mg/L−135.0 mg/L850.0 mg/L×100%=84.12%\text{Percentage reduction} = \frac{C_{\text{initial}} - C_{\text{residual}}}{C_{\text{initial}}} \times 100\% = \frac{850.0\text{ mg/L} - 135.0\text{ mg/L}}{850.0\text{ mg/L}} \times 100\% = 84.12\%

    You calculated the percentage of initial nickel that remains in the effluent (135.0850.0×100%=15.88%\frac{135.0}{850.0} \times 100\% = 15.88\%) instead of the percentage removed (the reduction).

WHAT YOU DID WELL
Compliments from Your Teacher

You correctly calculated the moles of EDTA\ce{EDTA} required to reach the titration end point.

You used the correct atomic mass of nickel rather than the mass of the dimethylglyoximate complex.

You accurately converted mass and aliquot volume to report a residual concentration of 135.0 mg/L135.0\text{ mg/L}.

THE ERROR
Where Your ACEpath Teacher Spotted the Mistake
Residual Fraction vs. Percentage Reduction Confusion

You stopped after computing the residual fraction CresidualCinitial\frac{C_{\text{residual}}}{C_{\text{initial}}}, forgetting to subtract that value from 100%100\% to get the reduction.

WHY IT HAPPENED
ACEpath Teacher's Diagnosis

Confusing the fraction remaining (residual level) with the fractional change (reduction achieved by a removal process).

REASONING PATH
Your ACEpath teacher’s suggested approach
Define 'Reduction'
  • Reduction=Initial−Final\text{Reduction} = \text{Initial} - \text{Final}

  • Always find the amount removed before dividing by the initial amount: Initial−FinalInitial×100%\frac{\text{Initial} - \text{Final}}{\text{Initial}} \times 100\%, or compute 100%−%remaining100\% - \%\text{remaining}.

Sanity Check Green Removal Efficiency
  • A process that drops concentration from 850.0 mg/L850.0\text{ mg/L} to 135.0 mg/L135.0\text{ mg/L} removes most of the contaminant.

  • Check whether the calculated percentage reduction matches physical reality: removing >80%>80\% of the pollutant must give a reduction >80%>80\%, not ≈16%\approx 16\%.

CORRECTED PATH
ACEpath Teacher's Demonstration
  1. Calculate the concentration of nickel removed by the precipitation treatment: ΔC=Cinitial−Ctreated=850.0 mg/L−135.0 mg/L=715.0 mg/L\Delta C = C_{\text{initial}} - C_{\text{treated}} = 850.0\text{ mg/L} - 135.0\text{ mg/L} = 715.0\text{ mg/L}.

  2. Divide the removed concentration by the initial concentration: Percentage reduction=715.0 mg/L850.0 mg/L×100%=84.12%\text{Percentage reduction} = \frac{715.0\text{ mg/L}}{850.0\text{ mg/L}} \times 100\% = 84.12\%.

Final answer

(a) 135.0 mg/L135.0\text{ mg/L}; (b) 84.12%84.12\%

NEXT STEPS
Final Takeaways from Your Teacher
  • Review the distinction between percent remaining and percent removed in effluent treatment scenarios.

  • Practice cross-checking the numerical magnitude of percentage reductions against the raw change in values.

Lock it in

Similar question

01

A 50.0 mL50.0\text{ mL} aliquot of treated wastewater containing residual ZnX2+\ce{Zn^{2+}} is titrated to the end point with 12.00 mL12.00\text{ mL} of 0.00500 M0.00500\text{ M} EDTA\ce{EDTA} (1:11:1 stoichiometry). Given the atomic molar mass of Zn=65.38 g/mol\ce{Zn} = 65.38\text{ g/mol} and the precipitate Zn(OH)X2=99.42 g/mol\ce{Zn(OH)2} = 99.42\text{ g/mol}, calculate the residual ZnX2+\ce{Zn^{2+}} concentration in mg/L\text{mg/L}.

Answer

78.46 mg/L78.46\text{ mg/L}. Key steps: nZnX2+=nEDTA=0.00500 M×0.01200 L=6.00×10−5 moln_{\ce{Zn^{2+}}} = n_{\ce{EDTA}} = 0.00500\text{ M} \times 0.01200\text{ L} = 6.00 \times 10^{-5}\text{ mol}. Mass of ZnX2+=6.00×10−5 mol×65.38 g/mol=3.923×10−3 g=3.923 mg\ce{Zn^{2+}} = 6.00 \times 10^{-5}\text{ mol} \times 65.38\text{ g/mol} = 3.923 \times 10^{-3}\text{ g} = 3.923\text{ mg}. Concentration =3.923 mg/0.0500 L=78.46 mg/L= 3.923\text{ mg} / 0.0500\text{ L} = 78.46\text{ mg/L}.

02

An electroplating plant reduces lead emissions by precipitating lead as PbSOX4\ce{PbSO4} (303.26 g/mol303.26\text{ g/mol}). The initial effluent contains 450.0 mg/L450.0\text{ mg/L} of PbX2+\ce{Pb^{2+}} (207.2 g/mol207.2\text{ g/mol}). A 100.0 mL100.0\text{ mL} sample of the treated effluent requires 15.50 mL15.50\text{ mL} of 0.002000 M0.002000\text{ M} EDTA\ce{EDTA} to reach the end point. Calculate: (a) the residual PbX2+\ce{Pb^{2+}} concentration in mg/L\text{mg/L}, and (b) the overall percentage reduction in lead emission.

Answer

(a) 64.23 mg/L64.23\text{ mg/L}; (b) 85.73%85.73\%. Key steps: (a) n=0.002000 M×0.01550 L=3.100×10−5 moln = 0.002000\text{ M} \times 0.01550\text{ L} = 3.100 \times 10^{-5}\text{ mol}. Mass of PbX2+=3.100×10−5 mol×207.2 g/mol=6.423 mg\ce{Pb^{2+}} = 3.100 \times 10^{-5}\text{ mol} \times 207.2\text{ g/mol} = 6.423\text{ mg}. Residual [PbX2+]=6.423 mg/0.1000 L=64.23 mg/L[\ce{Pb^{2+}}] = 6.423\text{ mg} / 0.1000\text{ L} = 64.23\text{ mg/L}. (b) Reduction=450.0−64.23450.0×100%=85.73%\text{Reduction} = \frac{450.0 - 64.23}{450.0} \times 100\% = 85.73\%.

03

A hydrometallurgical waste stream has an initial cadmium concentration of 1200 mg/L1200\text{ mg/L}. Cadmium is removed by precipitation as CdS\ce{CdS} (144.48 g/mol144.48\text{ g/mol}, Cd=112.41 g/mol\ce{Cd} = 112.41\text{ g/mol}). To assess compliance with an environmental standard requiring >95.0%> 95.0\% emission reduction, a 250.0 mL250.0\text{ mL} aliquot of the filtered liquid is titrated with 8.20 mL8.20\text{ mL} of 0.0100 M0.0100\text{ M} EDTA\ce{EDTA}. Determine whether the process meets the regulatory emission reduction target.

Answer

Yes, it meets the standard (96.9%>95.0%96.9\% > 95.0\%). Key steps: nCdX2+=0.0100 M×0.00820 L=8.20×10−5 moln_{\ce{Cd^{2+}}} = 0.0100\text{ M} \times 0.00820\text{ L} = 8.20 \times 10^{-5}\text{ mol}. Mass of CdX2+=8.20×10−5 mol×112.41 g/mol=9.218 mg\ce{Cd^{2+}} = 8.20 \times 10^{-5}\text{ mol} \times 112.41\text{ g/mol} = 9.218\text{ mg}. Residual [CdX2+]=9.218 mg/0.2500 L=36.87 mg/L[\ce{Cd^{2+}}] = 9.218\text{ mg} / 0.2500\text{ L} = 36.87\text{ mg/L}. Percentage reduction =1200−36.871200×100%=96.93%= \frac{1200 - 36.87}{1200} \times 100\% = 96.93\%, which surpasses the 95.0%95.0\% threshold.

Loading workspace…