Resources
In an analytical chemistry laboratory, a potentiometric titration is monitored at using an indicator platinum electrode and a saturated calomel reference electrode (SCE, ). A aliquot of is titrated with according to . Given for , calculate the potential of the indicator electrode versus standard hydrogen electrode () and the measured overall cell potential () after the addition of exactly of the titrant (the midpoint of the titration before the equivalence point).
Answer and steps
Final answer
;
Steps
Calculate the moles of reactants and products
The titration reaction is:
First, calculate the initial moles of present in the titration flask:
Next, calculate the moles of added:
Because the stoichiometric ratio is , the added acts as the limiting reactant:
- Moles of remaining:
- Moles of produced:
Since both ions share the same solution volume:
Determine the indicator electrode potential ()
Before the equivalence point, the potential of the platinum indicator electrode is determined by the unreacted analyte redox couple ():
Applying the Nernst equation at ():
Substitute :
Calculate the overall cell potential ()
The measured cell potential relative to the saturated calomel reference electrode () is:
Substitute the values:
Common Pitfall: At the midpoint (half-equivalence point) of a symmetrical redox titration, the ratio of oxidized to reduced form of the analyte is exactly , making the logarithmic term vanish regardless of total solution volume. Be careful to subtract, not add, the reference potential when finding the net cell potential measured across the two electrodes.
Typical errors
01 The student adds the reference electrode potential instead of subtracting it when calculating the cell potential.
Sample Student Work
Reviewed by ACEpath TeacherStep-by-Step Review
Walk Through It with Your Teacher- Step 1
- Step 2
- Step 3Correct
You added the reference electrode potential to rather than subtracting it. In a standard potentiometric cell where the indicator acts as the working electrode against a reference electrode, the measured voltage is .
WHAT YOU DID WELL
Compliments from Your TeacherYou calculated the titration midpoint volume accurately.
You identified that the reaction ratio of reduced to oxidized species is at the half-equivalence point.
You applied the Nernst equation correctly to find the potential of the indicator electrode versus SHE.
THE ERROR
Where Your ACEpath Teacher Spotted the MistakeYou initially wrote the correct subtraction , but crossed it out and changed the operation to addition.
WHY IT HAPPENED
ACEpath Teacher's DiagnosisConfusing cell potential convention with standard additive combinations, forgetting that the reference electrode potential serves as the baseline to subtract ().
REASONING PATH
Your ACEpath teacher’s suggested approach- Potentiometric Cell Voltage Formula
Always subtract the reference electrode potential () from the indicator electrode potential () when measuring potential difference against a reference electrode.
CORRECTED PATH
ACEpath Teacher's DemonstrationTake the indicator potential: .
Substitute into the potentiometric cell equation: .
Perform the subtraction: .
;
02 The student confuses the midpoint before the equivalence point with the equivalence point, mistakenly assuming all Fe²⁺ is completely reacted to leave zero remaining.
Sample Student Work
Reviewed by ACEpath TeacherStep-by-Step Review
Walk Through It with Your Teacher- Step 1
- Step 2Correct
Because is the limiting reagent before the equivalence point, adding of consumes only of , leaving of unreacted along with of newly formed .
- Step 3Correct
E_{\text{ind}} = E^\circ_{\ce{Fe^{3+}/Fe^{2+}}} - 0.0592\text{ V} \log_{10}\left(\frac{[\ce{Fe^{2+}}]}{[\ce{Fe^{3+}}]} ight) = +0.771\text{ V} - 0.0592\text{ V} \log_{10}(1) = +0.771\text{ V}
This step was thrown off by the zero concentration assumed in Step 2. With equal concentrations of and at the midpoint, the reaction quotient ratio is , making and .
- Step 4Correct
You correctly used the relationship , but your final number was affected by the incorrect value of .
WHAT YOU DID WELL
Compliments from Your TeacherYou calculated the initial moles of analyte and added moles of titrant accurately.
You correctly recalled the formula connecting cell potential, indicator electrode potential, and reference electrode potential ().
THE ERROR
Where Your ACEpath Teacher Spotted the Mistakenone
WHY IT HAPPENED
ACEpath Teacher's DiagnosisYou confused the half-equivalence point (midpoint) with the equivalence point, assuming that the analyte was completely consumed rather than recognizing that titrant is the limiting reactant and only half of the initial has reacted.
REASONING PATH
Your ACEpath teacher’s suggested approach- Identify the Limiting Reactant
Before the equivalence point in a titration, the added titrant is the limiting reactant, leaving unreacted analyte in the titration mixture.
Set up an ICF (Initial-Change-Final) mole table to subtract the consumed analyte moles from the initial analyte moles.
- Midpoint / Half-Equivalence Principle
At exactly half the volume required for equivalence, exactly half of the analyte has been converted into product, so .
Notice that , which makes the logarithmic term in the Nernst equation zero, yielding .
CORRECTED PATH
ACEpath Teacher's DemonstrationSet up an ICF table for : Initial , added .
Since is limiting, consumed , leaving and forming .
In the same solution volume, , so the ratio .
Apply the Nernst equation: .
Calculate the measured cell potential: .
;
03 The student inverts the ratio of reduced and oxidized species in the Nernst log term and evaluates log(2) instead of recognizing the concentrations are equal.
Sample Student Work
Reviewed by ACEpath TeacherStep-by-Step Review
Walk Through It with Your Teacher- Step 1
- Step 2Correct
Because of and of share the same solution volume, their concentration ratio is . Since , the logarithmic term vanishes entirely at the midpoint, giving .
- Step 3Correct
You applied the correct cell potential formula , but your numerical result was affected by the earlier calculation of .
WHAT YOU DID WELL
Compliments from Your TeacherYou accurately found the initial moles of analyte and titrant to determine remaining and formed quantities.
You recognized that the cell potential is measured as the indicator potential minus the reference potential.
THE ERROR
Where Your ACEpath Teacher Spotted the Mistakeno
WHY IT HAPPENED
ACEpath Teacher's DiagnosisYou used an arbitrary ratio of 2/1 in the Nernst term instead of using the ratio of the calculated equimolar quantities (1.00 mmol / 1.00 mmol = 1) at the half-equivalence point.
REASONING PATH
Your ACEpath teacher’s suggested approach- Evaluate the concentration ratio at the half-equivalence point
At the half-equivalence point of a 1:1 redox titration, exactly half of the initial analyte has reacted, so .
Always substitute the ratio of your calculated molar quantities into the Nernst quotient; when the amounts are equal, and .
- Check the Nernst quotient sign convention
For a reduction half-reaction , the Nernst equation is or .
Match the sign in front of the log term with the correct placement of reduced and oxidized species.
CORRECTED PATH
ACEpath Teacher's DemonstrationSet up the Nernst equation with the ratio of equimolar species: .
Compute the overall cell potential against the saturated calomel electrode: .
;
Lock it in
How is measured cell potential () related to the indicator electrode potential () and reference electrode potential ()?
.\nMemory cue: Measured voltage is the difference between working and reference electrodes.
Similar question
A potentiometric titration is monitored using an indicator electrode and an reference electrode (). If the indicator electrode potential versus SHE is determined to be , calculate the measured cell potential .
Answer
. Key step: .
In a potentiometric titration of of with monitored with SCE (), calculate and at the half-equivalence point. (Given: ).
Answer
, . Key steps: At the half-equivalence point, , so . Then .
A student measures an overall cell potential of using a saturated calomel electrode (SCE, vs SHE) connected as the reference electrode. What is the actual potential of the indicator electrode versus the standard hydrogen electrode ()?
Answer
. Key steps: Rearrange to give .